Professional Documents
Culture Documents
Installation Manual: MX-2301N MX-2600N/3100N MX-2600G/3100G
Installation Manual: MX-2301N MX-2600N/3100N MX-2600G/3100G
INSTALLATION MANUAL
CODE: 00ZMX3100/I3E
MX-2301N 2
MX-2600N/3100N
MODEL MX-2600G/3100G
CONTENTS
[ 9 ] MX-PNX5A/B/C/D . . . . . . . . . . . . . . 9-1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
CONFIGURATION
MX-3100N
Service Manual
STAPLE CARTRIDGE
12 MX-SCX1 REVERSING
SINGLE PASS FEEDER DOCUMENT COVER
EXIT TRAY UNIT
6 MX-TRX1 1 MX-RPX2 2 MX-VRX1
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
FINISHER
7 MX-FNX9 2 MX-2301N/2600N/3100N Paper feed system
PUNCH MODULE
10 MX-PNX1 MX-2600G/3100G
A/B/C/D
STAPLE CARTRIDGE
12 MX-SCX1 LARGE CAPACITY TRAY
5 MX-LCX1
STAPLE CARTRIDGE
13 AR-SC3 (For saddle)
PAPER PASS UNIT
8 MX-RBX3
SADDLE STITCH
FINISHER
9 MX-FN10
PUNCH MODULE
11 MX-PNX5 STAND/1 x 500 SHEET STAND/2 x 500 SHEET
A/B/C/D PAPER DRAWER PAPER DRAWER
3 MX-DEX6 4 MX-DEX7
Printer expansion Image send expansion
PRINTER
EXPANSION KIT BARCODE FONT KIT
14 MX-PBX3 17 AR-PF1 FACSIMILE INTERNET FAX APPLICATION
EXPANSION KIT STAMP UNIT EXPANSION KIT INTEGRATION MODULE
PS3 EXPANSION KIT 18 MX-FXX2 19 AR-SU1 21 MX-FWX1 23 MX-AMX1
15 MX-PKX1
NETWORK SCANNER
XPS EXPANSION KIT STAMP CARTRIDGE EXPANSION KIT
16 MX-PUX1 20 AR-SV1 22 MX-NSX1
Authentication/Security Application/Solution
MX-3100N CONFIGURATION - i
2 : '09/Sep
3. Combination of options
MX-3100N CONFIGURATION - ii
2 : '09/Sep
A. Delivery notes
For installation of a large size machine, be sure to check that the
door size is great enough before bringing in.
B. Installation area
The following space must be provided around the machine in order
to assure machine performances and proper operations.
If any option is installed, provide the additional space for installing
it.
Especially the space at the rear of the machine must be provided
sufficiently. If not, the machine cannot exhibit functions against E. Environmental conditions
heat and dust, causing some troubles. (1) Temperature and humidity
This machine is designed to perform properly under the specified
30cm temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
30cm 45cm Do not install the machine near a heater, a cooler, or a humidifier.
B. Delivery
(3) Direct rays of sunlight Remove the packing materials prior to installation in the office envi-
If the machine is installed under the rays of the sun, the exterior of ronment.
the machine may be discolored and abnormal copies may be pro-
duced.
3. Unpacking
A. Unpacking procedure
1) Remove the PP band.
2) Remove the internal packing pads with the machine.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
1 2 3
4 5
4. Installation
<Note before installation>
* When connecting the main unit with the optional STAND/2 X 500
SHEET PAPER DRAWER (MX-DEX7) or MACHINE STAND
(MX-DSX2), first unpack and install the STAND/2 x 500 SHEET
PAPER DRAWER (MX-DEX7) or MACHINE STAND (MX-
C. Removal of parts packed together DSX2); then unpack the main unit and securely place the main
unit on the MX-DEX6 or MX-DEX7 before installing the main unit.
A. Lock release
(1) Tray rotation plate lock release
1) Pull out the tray, and remove the rotation plate fixing material
and the tray note label.
A
A
B A
12) Secure with fixing screw. Lower the DV lock lever until it clicks
A closed.
2
9) Secure the DV cover with the two screws.
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
$8720$7,&'(9(/23(5$'-8670(17
$7'(9($'-B/B. $7'(9(92B0B.
14) Install the waste toner box (package part No. 3). $7'(9($'-B/B& $7'(9(92B0B&
$7'(9($'-B/B0 $7'(9(92B0B0
$7'(9($'-B/B< $7'(9(92B0B<
$7'(9($'-B0B.
$7'(9($'-B0B&
$7'(9($'-B0B0
$7'(9($'-B0B<
$7'(9(92B/B.
$7'(9(92B/B&
$7'(9(92B/B0
$7'(9(92B/B<
. & 0 < (;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
$8720$7,&'(9(/23(5$'-8670(17
$7'(9($'-B/B. $7'(9(92B0B.
ON $7'(9($'-B/B& $7'(9(92B0B&
$7'(9($'-B/B0 $7'(9(92B0B0
$7'(9($'-B/B< $7'(9(92B0B<
$7'(9($'-B0B.
$7'(9($'-B0B&
$7'(9($'-B0B0
$7'(9($'-B0B<
$7'(9(92B/B.
$7'(9(92B/B&
$7'(9(92B/B0
$7'(9(92B/B<
. & 0 < (;(&87(
3) With the front cabinet open, turn on the power switch on the
Note: Be sure to select all of the four colors: K, C, M, Y
operation panel.
7) After the machine completes cycling, exit the simulation mode
by pressing the [CA] key on the main unit.
<State of switch>
OFF ON
2
3) Open the front cabinet, and insert each toner cartridge.
Y M C Bk
B
B
5) Replace the LSU claning bar to the front cover and attach the
waste toner box.
A
2 1
4) Touch the [Change] key in the above screen to change the set-
tings. The following settings can be configured.
1
Item Description
Type Select the type of paper that is loaded in the tray.
The paper types that can be selected vary by paper
tray.
Size Select the paper size from the list. The paper sizes
that can be selected vary by tray. The sizes that
can be selected may also be restricted by the paper
type selected above.
If the desired size does not appear in the list, select
I. Tray setup [Custom Size] and directly enter the size (only for
the bypass tray).
(1) Simulation setup Feeding Approved Select the modes that can be used. If there is a
Change the tray setting in the "system setting" mode. If "Disabling Job function that you do not wish to be used with the
of Tray Settings" has been enabled in the system settings (adminis- selected tray, disable the function. When the "Type"
trator), the tray settings (except for the bypass tray) cannot be con- is other than plain paper, recycled paper, colored
figured. paper, or a user type, [Fax] and [Internet Fax]
cannot be selected.
1) Press the [SYSTEM SETTINGS] key.
(2) Tray size setup
JOB STATUS PRINT
1) Pull out the paper tray.
READY
DATA Gently pull the tray out until it stops.
SYSTEM
SETTINGS IMAGE SEND If paper remains in the tray, remove it.
LINE
DATA
HOME
LOGOUT
SIM No Content
26 2 LCC paper size setting
3 Used to set the auditor specification mode.
5 Used to set the count mode of the total counter and
(;(&87( 2.
the maintenance counter.
18 Used to set YES/NO of the toner save mode (Only 㪈㪇 key
in UK and Japan versions) EXECUTE
* For other destination versions, this setup is EXECUTE
or end of print
made by the user program.
52 Used to set YES/NO of counting when non-print
ǂǂǂ6,08/$7,21ǂǂ12 &/26(
paper is passed through each counter.
7(67
/68326,7,21$'-8670(176(/)35,17
1
K. Image quality check
(Image Quality Check Flowchart)
Step 1: Image Skew Check
Perform Simulation 50-22 (select "ALL").
If Image Skew is "OK" for all Colors, proceed to Step 2.
If Image Skew is "NG" for any Colors, Proceed to Black Laser (;(&87( 2.
* When "R" is displayed in front of the value, turn and click the
skew adjustment screw (LSU) clockwise by the number of the
value.
* When "L" is displayed in front of the value, turn and click the Diagonal line D
skew adjustment screw (LSU) counterclockwise by the number
of the value.
At that time, the fractional part after the decimal point is rounded.
NOTE: The K (black) image skew level cannot be checked with
this adjustment. Diagonal line C
To check and adjust the K (black) image skew, follow the
procedures below and execute the adjustment.
b) Calculate the difference between the measured lengths C 9) If the adjustment result reaches the satisfactory level, tighten
1
and D of the diagonal lines. the adjustment screw.
c) Check to insure that the difference between C and D is in (The black image skew adjustment is completed with the
the following range. C – D = ±0.8mm above.)
If the difference between C and D is in the above range, there 10) In the above black image skew adjustment, check the color
is no need to adjust. image skew pattern printed when completion of the adjust-
(Method 2) ment.
a) Fit the side of A3 or 11" x 17" paper to the long side of the
4
rectangle print pattern.
Comparison line
A3 or 11 x 17 paper *B
0.5mm or less 4
Yellow
Magenta
Cyan
*A
Direction A
Direction B
Direction A Direction B
*B
mode. Check to confirm that the image loss and the void area are
in the range shown below. 5) Press [EXECUTE] key.
The adjustment pattern is printed out.
Content Standard adjustment value (Each paper is fed from selected paper feed tray, and the indi-
Lead edge void area 3.0±1.0mm vidual pattern according to each paper feed tray is printed out.)
Rear edge void area 2.0 - 5.0mm
6) Set the adjustment pattern on the document table. (Any direc-
FRONT/REAR void area 2.0±2.0mm
tion)
Lead edge image loss adjustment 3.0±1.0mm
Side image loss adjustment 2.0±1.0mm NOTE: Fit the adjustment pattern correctly with the document
guide.
NOTE: For details of the checking procedures of the image loss
and the void area, refer to the ADJ17 and the ADJ18.
(Adjustment procedure)
a. Image off-center automatic adjustment
(in original table mode)
1) Enter the SIM50-28 mode.
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
$872,0$*(326,7,21$'-8670(176(59,&(
2&ǂ$'- %.0$*ǂ$'-
63)ǂ$'- 6(78335,17ǂ$'-
5(68/7 '$7$
(Note)
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
* [LEAD]: Print image lead edge image position adjustment
* [OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
1 b. Copy lead edge image reference position adjustment, 6) Press [EXECUTE] key.
image off-center, and sub scanning direction image magni-
fication ratio automatic adjustment. (in original table mode)
ǂǂǂ6,08/$7,21ǂǂ12
1) Enter the SIM50-28 mode. 7(67
$872,0$*(326,7,21$'-8670(176(59,&(
&/26(
3/($6(:$,7
12:(;(&87,1*
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
$872,0$*(326,7,21$'-8670(176(59,&(
2&ǂ$'- %.0$*ǂ$'-
63)ǂ$'- 6(78335,17ǂ$'-
5(68/7 '$7$
5(35,17 (;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
ǂǂǂ6,08/$7,21ǂǂ12 $872,0$*(326,7,21$'-8670(176(59,&(
7(67 &/26(
6,08/$7,21&203/(7(
$872,0$*(326,7,21$'-8670(176(59,&(
3/($6(386+&$.(<
0)7 &6 &6
(;(&87(
2&ǂ$'- %.0$*ǂ$'-
63)ǂ$'- 6(78335,17ǂ$'-
5(68/7 '$7$
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
$872,0$*(326,7,21$'-8670(176(59,&(
6,'( 6,'(
$//
3/($6(86(63(&,),('7<3(2)$25h6,=(3$3(5
)257+,6$'-8670(17
(;(&87(
$1'35,177+(7(673$7&+
3/($6(86(63(&,),('7<3(2)$25h6,=(3$3(5
)257+,6$'-8670(17
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
(1*,1($872$'-8670(176(59,&(
3/($6(6(/(&77+(02'()$&725<256(59,&($1'3/$&(
7+(35,17('7(673$7&+21'2&80(17*/$667+(135(66>(;(&87(@
/,*+7$5($$7/()76,'(21'2&80(17*/$66
(;(&87(
PRINTER CALIBRATION *1 *1
$M
3
Ტ/CZᲣ
# $ % & ' ( ) * + , - . / 0 1 2
*1: In the case of the GDI printer, this section are not printed.
Remark: 7) Press [FACTORY] key on the operation panel, and press
(Descriptions on the factory service key button in the color bal- [EXECUTE] key.
ance automatic adjustment menu)
There are two kinds of the gamma target for the color balance
automatic adjustment: the factory target and the service target.
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
FACTORY key and SERVICE key are used to select one of (1*,1($872$'-8670(176(59,&(
%
*1: In the case of the GDI printer, this section is not printed.
8) The initial setting menu of the half tone image correction is dis- $M
played. Press [OK] key.
CMY
The initial setting of the half tone image correction is per- Blend
formed. 3
/CZ
# $ % & ' ( ) * + , - . / 0 1 2
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
(1*,1($872$'-8670(176(59,&(
2) Patch C or D of each of Y, C, M, and
&21),507+($'-867('3$7&+$1'35(66>2.@725(*,67(57+,63$7&+'$7$ BK is very slightly copied.
Patch A of each of Y, M, C, and
BK are not copied.
*1: In the case of the GDI printer, this section is not printed.
If the color balance of each patch of the process black (CMY
mixed color) is slightly shifted to Magenta, it means that the
adjustment is proper. If the color balance of the adjustment
pattern printed in this mode is slightly shifted to Magenta, it is
converted into the natural gray color balance by the color table
in an actual printer mode. (When the color balance target is
DEF 1.)
If a satisfactory result on the print color balance and the den-
sity is not obtained with the automatic adjustment, execute the
manual adjustment (SIM 67-25) (ADJ 21B).
1. Unpacking
A. Removal of the desk unit
1 2
No. Names of bundles Quantity
1 Right adjuster 1
2 Fixing screws (M4 x 8) 4
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
<State of switch>
OFF ON
3) Disconnect the power plug of the main unit from the power out-
let.
MX-3100N MX-DEX6/DEX7 2 – 1
B. Installation of the adjuster 2) Put the main unit on the desk unit.
1) Install the right adjuster (package part No. 1) to the desk unit. * Use man power of four persons or more to lift the main unit.
* Place the main unit on the desk unit slowly by fitting the
external lines. Check to insure that the positioning pin on the
top of the desk unit is securely engaged in the positioning
groove of the main unit.
1
1
MX-3100N MX-DEX6/DEX7 2 – 2
5) Lift the connection plates on the right and left of the main unit 7) Lift the connection plates, and fix them with the fixing screws.
front side, and fix them with the fixing screws (package part
No. 2).
2
2
MX-3100N MX-DEX6/DEX7 2 – 3
D. Release the lock E. Connector connection
1) Pull out each tray. 1) Remove the screw from the back of the main unit. Remove the
connector cover.
2) Turn and remove the fixing material, and remove the caution 2) Connect the connector.
sheet.
NOTE:
Before turning on the power, check to insure that the fixing 4) Install the connector cover and fix it with a screw.
material of the tray is disengaged. If the power is turned on
without disengaging the fixing material, a trouble may be
resulted.
4) Close the cassette which was pulled out.
MX-3100N MX-DEX6/DEX7 2 – 4
F. Turn on the power of the main unit 2) This screen allows you to configure the print off-center adjust-
1) Insert the power plug of the main unit into the power outlet. ment value for each paper feed tray.
<Detailed Description>
Setting
Item Display Description Default
range
E CS3 Print off-center adjustment value 1 to 99 50
(tray 3)
F CS4 Print off-center adjustment value 1 to 99 50
(tray 4)
3) On the touch panel, press [↓] to select "E: 50 : CS3" or "F:
50 : CS4."
4) Enter the desired adjustment value through the numeric key-
pad.
2) Open the front cabinet. (This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
Turn ON the power switch in the front cabinet of the main unit.
• Reducing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the rear.
• Increasing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the front.
5) After entering the adjustment value, press the [EXECUTE] key
ON
on the touch panel to start printing and save the setting.
6) Check that the adjustment pattern image is printed in the cor-
rect position.
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met:
+ 3.0mm
A-B = 0 -
<State of switch>
OFF ON B
A: 100 B : 50 ; MTF
C : 50 ; CS1
[64 - 140]
D : 50 ; CS2
EXECUTE OK
MX-3100N MX-DEX6/DEX7 2 – 5
[3] MX-TRX1
MX-3100N 2) Open theManual
Service front cabinet.
Turn OFF the power switch in the front cabinet of the main
unit.
1. Unpacking
A. Removal of the exit tray unit
OFF
3) Disconnect the power plug of the main unit from the power out-
let.
2. Installation
<Note before installation> 2
* Before starting installation, check to insure that the data lamp on
1
the operation panel does not light up or blink.
<State of switch>
OFF ON
MX-3100N MX-TRX1 3 – 1
3) Remove the screw, and remove the paper exit cover. C. Turn on the power of the main unit.
1) Insert the power plug of the main unit into the power outlet.
ON
1
OFF ON
D. Tray setting
Use SIM26-1 to set the tray YES/NO.
6) Install the exit tray unit (A) and the full detection actuator (B)
(package part No. 2).
* Be careful of the installing direction of the full detection actu-
ator.
B
B
MX-3100N MX-TRX1 3 – 2
[4] MX-RPX2
MX-3100N 2. Installation
Service Manual
<Note before installation>
1. Unpacking * Before installation, check to insure that the data lamp on the
operation panel does not blink or light up.
A. Removal of the RSPF
A. Turn off the power of the main unit.
1) Turn OFF the power switch on the operation panel.
<State of switch>
OFF ON
OFF
2 3 4
MX-3100N MX-RPX2 4 – 1
2) Remove the screws, and remove the glass holder (A). 5) Loosen the screw on the angle adjustment plate in the rear
Slide the table glass (B) in the arrow direction. side of the machine and lower the angle adjustment plate.
Remove the screws, and remove the glass holding left OC (C).
Arrange the SPF glass unit (D) (package part No. 1) and
tighten the screws.
3 C
2 A
B
D 6) Raise the RSPF unit upright, and fix it with the accessory
screw (M5 x 16) (package part No. 4).
3) Cut the screw hole in the cabinet, and install the SPF step 2
screw R (a) (package part No. 3) and the step screw R (b)
(package part No. 2). 2
1
b a b
2
a
1
7) Remove the connector cover. Connect the interface connector.
Check to insure that the projection (A) of the interface connec-
tor is in the groove on the main unit side as shown in the fig-
ure.
Tighten the connector fixing screw.
4) Insert the SPF step screw R and the step screw R into the
screw hole in the hinge section of the RSPF unit. Slide the unit A
toward the front side and close.
2
3
2
1
MX-3100N MX-RPX2 4 – 2
C. RSPF height adjustment
1) Make an RSPF height adjustment sheet
Cut copy paper in the longitudinal direction.
20mm
A4/Letter size
Is No Is No The height on
there a resist- there a resist- the right side
ance? ance? is not proper.
Yes Yes
A
MX-3100N MX-RPX2 4 – 3
c) Check section B.
Place the RSPF height adjustment sheet between section B
and the SPF glass height adjustment resin surface (a), and
close the RSPF unit.
Slowly pull out the RSPF height adjustment sheet.
Check to insure that a slight resistance is felt when pulling out
Check section B. the RSPF height adjustment sheet.
Is
there a re- No
sistance?
a
Yes
Adjust hinge E
until there is a
resistance in
section B.
(Clockwise)
Adjust hinge E
until the E
separation in
section C is
deleted.
(Counter-
clockwise)
e) Check section C.
Check to confirm that the projection in section C in the right
Check section C. front side of then RSPF bottom is in contact with the glass
surface (b).
C
b
MX-3100N MX-RPX2 4 – 4
D. Turn on the power of the main unit. E. RSPF diagonal adjustment
1) Insert the power plug of the main unit into the power outlet. 1) Set a test chart (A3) on the RSPF document tray, and make a
copy.
2) Measure (a) and (b) on the copied test chart. If (a) – (b) =
±1mm or more, perform the diagonal adjustment.
a
TEST CHART
2) Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
A3 size
b
ON
<State of switch>
OFF ON
4) Raise the RSPF unit upright, and loosen the fixing screw of the
hinge.
2
1
MX-3100N MX-RPX2 4 – 5
5) Close the RSPF unit, and loosen the hex nut of the RSPF G. Adjustment simulations
diagonal adjustment screw section.
(1) SPF size width detection level adjustment
Turn the hex wrench of the RSPF diagonal adjustment screw
to adjust the alignment. 1) Go to SIM53-6.
2) Set the tray document guide to the max. width position, and
press [EXECUTE] key. The button is highlighted and the tray
size volume maximum value adjustment is started.
3
* During the adjustment, "EXECUTING..." is displayed.
* After completion of the tray size volume maximum value
adjustment, the set value is saved to EEPROM and RAM
and the display is shifted to the tray volume A4R size adjust-
ment value start screen. (Each set value is saved to
1 EEPROM and RAM at each setting.)
2 3) Set the tray document guide to A4R (11 x 8.5R) width position
and press [EXECUTE] button. The pressed button is high-
lighted and the tray A4R size adjustment is started.
4) Adjust the tray volume A5R (8.5 x 5 1/2R) size and the tray
size volume minimum value according to the above proce-
dures.
* In the case of (A), turn the RSPF diagonal adjustment screw 5) After completion of the adjustment, "COMPLETE" is displayed.
counterclockwise. If the adjustment is not completed normally for any rea-
In the case of (B), turn the RSPF diagonal adjustment screw son,"ERROR"is displayed. In that case, the adjustment must
clockwise. be executed again.
<Adjustment item and content>
No. Display Content
1 TRAYVOLMAX Tray size volume maximum value
2 TRAYVOLA4R Tray volume A4R size adjustment value
3 TRAYVOLA5R Tray volume A5R size adjustment
4 TRAYVOLMIN Tray size volume minimum value
When one of 1-4 in the above table is selected, the guide plate is
shifted to each position of the four widths of the guide plate shown
in the table below. The value of the document width sensor
(RSPF_WIDTH) A/D value is saved to EEPROM.
<Guide plate positions and widths on the mechanism and A/D
A B values to be saved>
Widths on the mechanism A/D value,
Guide plate AB INCHI Code in the code in
No. Remark
position series series figure below the figure
below
1 Maximum 299 299 WIDTH_MAX AD_MAX
position
2 Middle 210 215.9 WITH_P1 AD_P1 A4R OR
position (L) LTR
3 Middle 148.5 139.7 WITH_P2 AD_P2 A5R OR
position (S) INVR
6) Make a copy again and measure (a) and (b) on the copied test 4 Minimum 118 118 WITH_MIN AD_MIN
chart. Repeat procedures 2) to 5) until the condition ((a)- position
(b)=±1mm or less) is satisfied.
[Initial screen]
F. Angle adjustment plate fixing
1) Lift the rear side of the machine and the angle adjustment 0
plate, and fix it with the screw. TEST SIMULATION NO.53-06 CLOSE
SPF TRAY ADJUSTMENT
TRAYVOLMAX TRAY ADJUSTMENT.
PRESS [EXECUTE] TO START
EXECUTE
MX-3100N MX-RPX2 4 – 6
(2) Auto void adjustment (SPF adjustment) 7) Press the [EXECUTE] button, and the machine starts reading
1) Go to SIM 50-28. SPF adjustment patterns (for the front side).
* The screen shows a message indicating that the machine is
0 reading and calculating SPF adjustment patterns (for the
TEST SIMULATION NO.50-28 CLOSE front side).
AUTO IMAGE POSITION ADJUSTMENT: SERVICE The machine starts calculating the adjustment amount (for
OC ADJ BK-MAG ADJ
the front side) after it has read the patterns for the front side.
SPF ADJ SETUP/PRINT ADJ After the machine has finished calculating the adjustment
RESULT DATA
amount for the front side, the next screen appears where
you can have the machine start reading SPF adjustment
patterns (for the back side).
1/1
<Adjustment Item List>
2) Press the [SPF ADJ] button. • SPF original leading edge adjustment (front side)
• SPF original off-center adjustment (front side)
0
TEST SIMULATION NO.50-28 CLOSE • SPF original sub-scan magnification adjustment (front side)
AUTO IMAGE POSITION ADJUSTMENT:SERVICE 8) SPF adjustment patterns are loaded into the SPF.
SIDE1 SIDE2
ALL
1/1
MX-3100N MX-RPX2 4 – 7
[5] MX-LCX1
MX-3100N 3) Remove the
Service paper feed desk fixing screw.
Manual
1. Unpacking
A. Removal of the large capacity tray unit
NOTE:
Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on
without removing the fixing screw, a trouble may be
resulted.
2 5
No. Names of bundles Quantity
1 Mounting plate upper 2
2 Connection unit 1
3 Fixing screw A (Hexagon with seat, S-tight, M4 x 35) 4
4 Fixing screw B (Hexagon with seat, S-tight, M4 x 12) 2
5 Fixing screw C (screw 4 x 8 cup) 1
2) Remove the fixing material and the packing parts.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
<State of switch>
OFF ON
MX-3100N MX-LCX1 5 – 1
2) Open the front cabinet. 3) Disengage the pawl, and remove the right adjuster.
Turn OFF the power switch in the front cabinet of the main unit.
1 1
OFF
3) Disconnect the power plug of the main unit from the power out- 4) Remove the screw cap, and remove the screw.
let.
1
2
1
3
2
MX-3100N MX-LCX1 5 – 2
7) Insert the temporarily fixed screw B into the key hole in the 2) Check to insure that the height adjustment check rib of the
connection unit (package part No. 2), and temporarily fix the large capacity tray unit and the axis line of the mounting plate
connection unit. upper mounted to the main unit are in the same line.
8) Fix the other fixing screw B (package part No. 4), and tighten
the temporarily fixed screw B securely.
NOTE:
If the screw is loosened or removed when servicing, be sure
to execute "C. Height adjustment of the large capacity tray
unit" after completion of servicing.
MX-3100N MX-LCX1 5 – 3
5) In the case of a shift to the right, press the front upper section 2) Connect the connector, and tighten the screw.
and fit the height adjustment check rib so that it is in the same
line with the axis line of the mounting plate upper. Insert the
large capacity tray unit into the main unit.
2) Loosen the stopper fixing screw (1 pc) on the right lower side
of the tray so that the stopper does not function.
MX-3100N MX-LCX1 5 – 4
a. Side plate size switch 2) Loosen the fixing screw (flat screw 1pc) of the auxiliary guide.
1) Remove four fixing screws (blue screws) which are fixing the 3) Set the mark position ( ) of the auxiliary guide and the cas-
upper and the lower sections of the side plate F and the side sette R to the size from A4 to LT, and fix with the fixing screw
plate R. (flat screw).
F side R side
A4 LT
At that time, set the mark position ( ) of the auxiliary guide
2) Adjust the mark position of the tray and the side plates in the and the cassette R to the same scale of the mark position ( )
lower section of the side plates F/R according to the desired of the side plate R and the size guide adjustment plate con-
size. Also adjust the upper section according to the desired firmed in procedure 1). (If the scale of the size guide adjust-
size, and fix with the four fixing screws (blue screws). ment plate is at the center, set it to the center. If the size guide
adjustment plate is in 1mm in the front side, set it in 1mm in the
front side.)
c. Rear edge shaft switch
1) Remove the rear edge shift fixing screw (blue screw) which is
fixing the shaft to the right side inside the tray, and remove the
rear edge shaft.
F side R side
2) Tighten the removed rear edge shaft with the fixing screw
(blue), and store it in the storage space inside the front cabi-
net.
MX-3100N MX-LCX1 5 – 5
3) Slightly push the tray, restore the stopper to the original posi- 2) Loosen the stopper fixing screw (1 pc) on the right lower side
tion, and fix the fixing screw. of the tray so that the stopper does not function.
At that time, check to insure that the stopper pawl is engaged 3) Pull out the tray again until it stops.
with the stopper reception of the large capacity tray unit.
F side R side
MX-3100N MX-LCX1 5 – 6
3) Slightly push the tray, restore the stopper to the original posi-
F side R side
tion, and fix the fixing screw.
2) Insert the removed rear edge shaft into the mounting hole in
the paper feed desk as shown in the figure below. Fix the
upper section with the fixing screw (blue screw) which was
removed previously.
NOTE:
When the rear edge shaft is switched to B5, check to confirm
that the side plates F/R are already set to B5. If the side plates
F/R are not set to B5, the rear edge shaft cannot be switched
to B5.
MX-3100N MX-LCX1 5 – 7
2) Open the front cabinet. 6) Check that the adjustment pattern image is printed in the cor-
Turn ON the power switch in the front cabinet of the main unit. rect position.
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met:
ON A
+ 3.0mm
A-B = 0 -
B
3) Turn ON the power switch on the operation panel.
No adjustment is needed if A - B = 0 ± 3.0 mm.
If the above condition is not met, do the following:
7) Change the adjustment value.
<State of switch> (Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
OFF ON approximately 0.1 mm.
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied.
8) After you have completed the adjustment, exit from simulation
G. Size setting mode by pressing the [CA] key.
Execute SIM 26-2 "Size setting" with the key operations of the main
unit. (2) Mechanical adjustment
1) The size selection menu of the large capacity tray is displayed Since the off-center adjustment is performed when shipping, there
on the operation message display. is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
2) Select a size button to be set on the message screen.
removed, perform the following adjustment procedures.
H. Off-center adjustment 1) Slowly pull out the tray until it stops.
(1) Adjustment with the simulation
1) Run SIM 50-10 using the keypad on the main unit.
The following screen appears.
0
TEST SIMULATION NO.50-10 CLOSE
EXECUTE OK
2) Loosen the stopper fixing screw (1 pc) on the right lower side
2) This screen allows you to configure the print off-center adjust- of the tray so that the stopper does not function.
ment value for each paper feed tray.
3) On the touch panel, press [↓] to select "G: 50 :LCC."
4) Enter the desired adjustment value through the numeric key-
pad.
(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
• Reducing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the rear.
• Increasing the adjustment value by 1 causes the main scan/
print position to shift by 0.1 mm toward the front.
5) After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting.
MX-3100N MX-LCX1 5 – 8
3) Pull out the tray again until it stops. b. When the shift is in the rear side
To adjust the print line in the direction B from the paper center as
shown in the figure:
1) Loosen two fixing screws (red screws) of the front/rear size
guide adjustment plate, and move the size guide adjustment
plate in the direction B (F side) by the shift amount, and tighten
the red fixing screws (2 for each). Restore the stopper to the
original position, and fix it with the fixing screws. Move the aux-
iliary guide in the direction B by the same size.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
R side
R side
F side
Slightly push the tray, restore the stopper to the original posi-
tion, and fix the fixing screw.
Check to insure that the stopper pawl is engaged with the stop-
per reception of the large capacity tray.
2) Slowly insert the tray to the original position.
Then make a copy to check to insure that there is no more
shift. Repeat the procedures until there is no shift.
MX-3100N MX-LCX1 5 – 9
[6] MX-FNX9
MX-3100N B. Removal
Service of the fixing tape and protection
Manual
material
1) Remove the fixing tape and protection material.
1. Unpacking
A. Removal of the inner finisher
1 2 3
4 5 6 7
8 9 10 11 12
MX-3100N MX-FNX9 6 – 1
2. Installation B. Removal of the paper holding arm unit
<Note before installation> 1) Push up the section A to disengage the pawl, and remove the
paper holding arm and the paper holding arm holder together
* Before starting installation, check to insure that the data lamp on
as a unit.
the operation panel does not light up or blink.
* Be careful to remove both of the paper holding arm (which is
A. Turn off the power of the main unit easily removed alone) and the paper holding arm holder.
1) Turn OFF the power switch on the operation panel.
<State of switch>
OFF ON
OFF
3) Disconnect the power plug of the main unit from the power out-
let.
MX-3100N MX-FNX9 6 – 2
3) Disengage two pawls, and remove the paper exit tray cover. 6) Engage the projection on the main unit frame with the hole in
the finisher fixing plate (package part No. 1).
7) Fix the right cover plate with the fixing screw (package part No.
8).
* Fix the side plate of the paper exit shifter with the fixing
guide.
5) Remove the paper exit full detection actuator. 8) Install the front slide rail (A) (package part No. 2) with the three
fixing screws (package part No. 8), and install the left front
cover (B) (package part No. 6) with one fixing screw (package
part No. 8).
B
9) Fix the dummy punch unit (package part No. 3) with the fixing
screw (package part No. 8).
MX-3100N MX-FNX9 6 – 3
10) Check to insure that the slide roller is in the rail groove, and 14) Fix the punch cover (package part No. 5) together with the
insert the inner finisher. band (metal fixture) with the fixing screw (package part No. 8).
11) Fix the rear slide rail with the fixing screw (package part No. 8).
15) Install the front cabinet upper with two screws.
12) After pushing the intermediate rail of accuride, insert the fin-
isher slide stopper (package part No. 7) between the rear slide
rail and the accuride.
Fix it with the coin screw (package part No. 10).
D. Connector Installation
1) Remove the protection material and fixing tape.
13) Install the front open/close cover (package part No. 4) to the 1
front rail stay rotating shaft, and fix it with the resin clip (pack-
age part No. 9).
2
MX-3100N MX-FNX9 6 – 4
3) Connect the finisher connector with the main unit connector, F. Turn on the power of the main unit
and tighten with a screw.
1) Insert the power plug of the main unit into the power outlet.
Lose the
clearance.
First label Second label
Corner R end fitting
Label attachment
reference Corner R end fitting
Corner of the "upper
cabinet rear"
<State of switch>
OFF ON
MX-3100N MX-FNX9 6 – 5
[7] MX-PNX1
MX-3100N C. Check the
Service packed items
Manual
1) Check that all the items are included in the package.
1. Unpacking
A. Removal of the punch unit
1 2
2. Installation
* When the punch unit is installed together with installation of
the MX-FNX9 (inner finisher), first install the inner finisher,
and then install the punch unit.
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
* Do not install the punch unit first because doing so would cause
interference between the inner finisher slide rail and the punch
unit drawer connector (possibly resulting in failure) when you
attempt to install the inner finisher.
<State of switch>
OFF ON
MX-3100N MX-PNX1 7 – 1
2) Open the front cabinet. 3) Remove the coin screw, and remove the finisher slide stopper.
Turn OFF the power switch in the front cabinet of the main unit.
OFF
3) Disconnect the power plug of the main unit from the power out-
let.
6) Remove the screw, and remove the band and the punch cover.
2) Open the front cover and slide the inner finisher to the left.
MX-3100N MX-PNX1 7 – 2
7) Remove the screw, and remove the dummy punch unit. 11) Remove the dust box.
12) Fix the punch cover and the band together with one screw.
1
8) Fix the punch unit with a screw.
* When installing the punch unit, be careful not to bump it
against the drawer connector.
* Fit the positioning pin and insert it.
3
2
9) Make positioning with the dove (A) and fix the punch unit with
the screw which was fixing the dummy punch unit.
14) Install the front cabinet upper part using the two screws
A removed in step 5).
15) Insert the finisher slide stopper between the slide rail and the
accuride, and fix it with the coin screw.
MX-3100N MX-PNX1 7 – 3
16) Slide the inner finisher to the original position, and close the D. Turn on the power of the main unit
front cover. 1) Insert the power plug of the main unit into the power outlet.
ON
Lose the
clearance.
First label Second label
Corner R end fitting
Label attachment
reference Corner R end fitting
Corner of the "upper
cabinet rear"
<State of switch>
OFF ON
MX-3100N MX-PNX1 7 – 4
[8] MX-RBX3, MX-FN10
MX-3100N C. Check the
Service packed items
Manual
1) Check that all the items are included in the package.
1. Unpacking the MX-RBX3
A. Removal of the interface pass unit
1 2 3
4 5 6 7
<State of switch>
OFF ON
OFF
4) Remove the paper exit full detection actuator (A), and install
the reverse detection actuator (B) (package part No. 6).
* Be careful of the installing direction of the reverse detection
actuator.
2
C. Installation of the interface pass unit A
1) Open the front cabinet. Remove the screws, and remove the
B B
front cabinet upper.
8) Fix the reverse tray with the resin crip (package part No. 5).
* Be sure to clamp and fix the paper exit tray shifter side plate
with the fixing guide.
6) Insert the rib of the interface left cabinet (package part No. 2)
into the slit on the lower surface of the scanner left cabinet.
Install the interface left cabinet with the fixing screw A (pack-
age part No. 4) of the paper exit tray which was removed in
procedure 4).
10) Install the front cabinet upper C unit, and fix with the screws.
12) Fix the interface pass disconnection preventing lever with the
fixing screw A (package part No. 4).
2) Holding the upper part of the saddle stitch finisher by two peo-
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot.)
1 2 3
4 5 6 7 8 9
10 11 12 13
5) Remove the other side similarly. No. Packed part names Quantity
1 Paper exit tray 1
2 Connection plate 1
1
3 Saddle tray 1
4 Paper holding A 1
5 Paper holding B 1
6 Fixing screw A 5
7 Fixing screw B 2
8 Fixing screw C 2
9 Staple cartridge 1
10 Staple position label (For scanner) 1
11 Staple position label (For RSPF) 1
2 12 Punch position label (For scanner) 1
13 Punch position label (For RSPF) 1
* The punch position labels (No.12 and No.13) should be kept at
hand since they will be necessary when installing the punch unit.
1 2
A A
Connection hole
Guide pin
1
2) Remove the two screws, and remove the front under cover Clearance
and foot cover.
2) If the upper and lower clearances between the main unit and
the finisher are not even, remove the screw (one for each) of
the foot covers on the front/rear sides, and remove the foot
cover.
2 2
1 1
4) When the clearances are even, tighten the fixing screw of the
adjustment section, and install the foot cover.
F. Connector connection
1) Connect the finisher connector with the connector of the inter-
face pass unit, and tighten the screw.
ON
<State of switch>
[For RSPF] (package part No. 11)
OFF ON
1. Unpacking
A. Removal of the punch unit
OFF
3) Disconnect the power plug of the main unit from the power out-
let.
1 2
000-0000
3
4) Disconnect the connector between the main unit and the sad-
dle finisher.
No. Packed part names Quantity
1 Harness A (Purple) 1
2 Harness B (Gray) 1
3 Punch jam processing label 1
* Use the punch position labels bundled with the MX-FN10.
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
<State of switch>
OFF ON
MX-3100N MX-PNX5A/B/C/D 9 – 1
B. Installation of the punch unit 4) Open the front cover. Remove the screw, and remove the front
1) Release the lock and separate the saddle finisher from the inner cover.
main unit.
MX-3100N MX-PNX5A/B/C/D 9 – 2
7) Connect the harness on the punch unit side with the PWB on 10) Fix the rear cover with a screw.
the finisher side.
8) Fix the front inner cover with screws, and close the front
cover.
000-0000
MX-3100N MX-PNX5A/B/C/D 9 – 3
D. Punch position label attachment E. Turn on the power of the main unit
1) Attach the label to the position indicated in the figure. 1) Connect the connector.
[For scanner]
Lose the
clearance.
First label Second label
Corner R end fitting
Label attachment
reference Corner R end fitting
Corner of the "upper
cabinet rear"
[For RSPF]
2) Insert the power plug of the main unit into the power outlet.
feed unit and clean the document scan
section with the glass cleaner (accessory).
ON
<State of switch>
OFF ON
MX-3100N MX-PNX5A/B/C/D 9 – 4
[10] MX-KBX1
MX-3100N 2. Installation
Service Manual
<Note before installation>
1. Unpacking * Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
<State of switch>
OFF ON
OFF
3) Disconnect the power plug of the main unit from the power out-
let.
1
2 3 4 5
6 7 8 9
MX-3100N MX-KBX1 10 – 1
B. Install the USB hub PWB. 4) Connect the connector of the scan mother harness, and con-
nect the mother PWB connection harness (part No.4 in the
1) Remove the screw, and remove the rear cabinet.
package).
3) Attach the USB hub PWB unit (part No.3 in the package) with
the removed screws.
MX-3100N MX-KBX1 10 – 2
1 : '08 Oct 15
2) Open the front cabinet, and remove the screw, and remove the 5) Remove the screw, and remove the panel angle.
front cabinet upper.
6) Install the keyboard unit (part No.1 in the package), and fix it
with the fixing screw A (part No.5 in the package) and the fix-
ing screw B (part No.6 in the package).
* When fixing the fixing screw B, use the short screwdriver or
3) Remove the screw, and remove the operation base plate unit.
the small screwdriver.
1
4) Remove the screws and disconnect two connectors. Place the
operation panel upside down on the protection sheet.
*1 *3
*2
*1: Don't pull the lead wire. The connector can be locked.
Hold the housing section of connector, pull out it.
*2: Slowly pull the lead wire and disconnect the connector.
*3: There is a locking section on the reverse side. Use care for
that.
MX-3100N MX-KBX1 10 – 3
1 : '08 Oct 15
1 2) Connect the connector. 7) Attach the front cabinet upper, and fix it with the screws.
3) Install the operation panel to the main unit, and fix it with the
screw.
*1
*2
ON
MX-3100N MX-KBX1 10 – 4
1 : '08 Oct 15
3) Turn ON the power switch on the operation panel. 2) Touch [Default Settings].
Keyboard Select
English English
French German Swedish Norwegian
(US) (UK)
System Settings
USB memory Clock Adjust
Keyboard Select
2) Check that the recognition mark displays on the lower right
section of the panel.
1
I. Language setting
Targets:
The model for 8.5 inch LCD panel with option keyboard installed.
The language selected should be the same as the layout of the
option keyboard, otherwise false input occur.
1) Press the [SYSTEM SETTINGS] key. 5) Press [CA] key to exit from system setting mode.
The following menu screen appears on the touch panel. End of language setting.
HOME
LOGOUT
MX-3100N MX-KBX1 10 – 5
[11] AR-SU1
MX-3100N 2) Open theManual
Service front cabinet, and turn OFF the power switch.
1. Unpacking
A. Remove the stamp unit
OFF
1 2
3 4
2. Installation
<Note before installation>
* Before execution of installation, check to confirm that the data
lamp on the installation panel does not light or flash. 2
3
A. Turn off the power of the main unit
1) Turn OFF the power switch on the operation panel.
<State of switch>
OFF ON
MX-3100N AR-SU1 11 – 1
* If stubby screwdriver is not available, loosen the screw of 4) Install the stamp case unit, and connect the connector.
the angle adjustment plate on the rear side of the machine,
and lower the angle adjustment plate and put the RSPF unit
straight.
1 2
1
6) Install the stamp cartridge (package part No. 3).
3) Attach the stamp unit (package part No. 1) to the stamp case
which was removed from the RSPF unit with the installing
screw (package part No. 4). (Fix it together with the earth
wire.)
2
1
MX-3100N AR-SU1 11 – 2
C. Turn on the power of the main unit
1) Insert the power plug into the power outlet.
2) Open the front cabinet of the machine, and turn ON the power
switch.
ON
<State of switch>
OFF ON
MX-3100N AR-SU1 11 – 3
[12] MX-PBX3
MX-3100N 2) Insert theManual
Service "Software CD-ROM" into the CD-ROM drive.
• To install the PCL printer driver, the PC printer driver, or the
PPD driver (when the expansion kit is installed), insert the
1. Unpacking "Software CD-ROM" with "for Windows Macintosh" speci-
fied on it into the CD-ROM drive.
3) Click [START] button and [My computer], and double-click
[CD-ROM] icon.
• In the case of Windows 98/Me/Nt 4.0/2000, double-click [My
computer] and double-click [CD-ROM] icon.
1 2 3 4 4) Double-click [SETUP] icon.
5) Confirm the contents of "Software License Agreement" dis-
A. Parts included played on the screen and press [YES]. Confirm the contents of
"Read me first" and click [NEXT] button.
6) Click [Printer Driver] button.
No. Packed part names Quantity
1 CD-ROM 1 • To install the PC-FAX driver, click [Support Tool] button, and
2 Product key sheet 1 click [PC-FAX driver] button.
3 BMLinkS label 1 • When [Detailed information display] button is clicked, the
4 On BMLinkS 1 detailed information of the software is displayed.
7) Click [NEXT] button and click [Standard install] button.
2. Installation The connection method is the LPR direct system. The name of
the printer driver can be fixed as the normally used printer. The
<Note before installation>
display font for the PCL printer driver is not installed.
NOTE: To enable the printer expansion function, the product key • Click [Custom install] button, and items can be changed and
must be acquired. (For the acquiring procedure of the prod- installed.
uct key, contact the distributor.)
8) The printer connected in the network is detected. Select this
When you acquire the product key, enter it on the product machine and click [NEXT] button.
key sheet (package part No. 2) and provide the sheet to the
• If this machine cannot be detected by retrieval, check to
user.
confirm that the power of this machine is turned ON and that
• To use the PS printer driver and the PPD driver, the PS expan- the machine is surely connected in the network, and click
sion kit is required. [Retrieval again] to perform retrieval again. With [Conditions
A. Preparations for enabling the printer setup] button, the model name of this machine (host name)
or the IP address can be used for retrieval.
expansion kit
9) The confirmation screen is displayed. Check the contents and
(1) Entering the product key click [NEXT] button.
1) To enable the printer expansion function, enter the product key When the printer driver selection screen is displayed, select
by the key operations on the operation panel. the printer driver to be installed, and click [NEXT] button.
a) Touch [PRODUCT KEY INPUT] key. 10) If the selection screen of the normally used printer is dis-
b) Enter the product key with the 10-key and touch [OK] key. played, select either item and click [NEXT] button.
2) After completion of entering the product key, turn OFF the 11) Check the contents according to the indications on the screen,
power switch of the machine and the main power switch, and and click [NEXT] button. Installation is started.
then turn ON the power switch and the main power switch. * In the case of Windows Vista:
(2) Printer driver/PC-FAX driver installation When the alarm window on security is displayed, click
* Use the packed CD-ROM (package part No. 1) to install the "Install this driver software."
printer driver and other drivers. * In the case of Windows 2000/XP/Server 2003:
Be sure to use this CD-ROM to install the PS printer driver and When the Windows logo test screen or the warning screen
the PPD driver. of digital signature is displayed, be sure to click [Continue] or
* Installation and setting of the driver software to the PC or the [OK] button.
server must be performed by the user himself/herself or by the 12) When the completion screen of installation is displayed, click
user's request. [Complete] button. Then click [CLOSE] button to terminate the
1) The machine must be connected in a network as shown below. installer.
(3) Adjust the printer driver to adapt with the machine
configuration.
TCP/IP network
(Local area network) After installation of the printer driver, the status of the peripheral
devices installed to the machine and the size and the type of paper
The LPR protocol is set in the machine must be set to the printer driver. Refer to the fol-
used for print-out. lowing procedures (when installing the standard printer driver) to
Windows computer set the printer driver.
(Connected in the same network) 1) Click [START] button and click [Printer and FAX] button.
* In the case of Windows XP/Server 2003, click [START] but-
* Installable OS: ton, and click [Printer and FAX] button.
Windows98/ Me (Administrator authority not required), Win- * In the case of Windows 98/Me/NT 4.0/2000, click [START]
dows NT4.0/ 2000/ XP/ Server2003/ Vista (Administrator button, select [Setting] and click [Printer] button.
authority required) * In the case of Windows XP, if [Printer and FAX] does not
appear on [START] menu, click [START] button and select
[Control panel] → [Printer and other hardware] → [Printer
and FAX] in this sequence.
MX-3100N MX-PBX3 12 – 1
2) Open the printer property screen.
a) Click the printer driver icon of this machine.
b) Click the [File] menu.
c) Select [Property].
3) Click [Option] tab.
* In the case of Windows 98/Me, click [Driver setting] tab, and
click [Option] tab on the displayed screen.
4) Click [Option auto setting] button.
The status of this machine is detected and setting is performed
automatically.
5) Set the image of this machine.
Set the image of this machine displayed on the printer driver
setting screen according to the peripheral devices installed to
the machine.
a) Select the peripheral device installed to the machine.
b) Click [OK] button.
• When [CANCEL] button is clicked, the automatic setting is
terminated. However, the contents which were automatically
set by step 4) are saved.
6) Click [OK] button on the property screen of the printer.
* If the automatic setting is failed, set manually.
• The status of the peripheral device installed to the machine
and the tray setting can be checked by printing the "All setting
list" of the system setting of the machine. The printing proce-
dure of the "All setting list" is as follows:
Press [System setting] key, [Data list print] key, and [All setting
list] key in this sequence.
• To check the contents of [Tray setting], [Paper type setting],
and [Tandem print setting], click each button to confirm.
• Paper type setting: The content of [Paper type setting] in
[Paper feed tray setting] of the system setting of the
machine is reflected. When the user type (1 – 7) is changed,
enter the changed type name.
MX-3100N MX-PBX3 12 – 2
1 : '08 Oct 15 2 : '09/Sep
1. Unpacking
A. Check the packed items
1) Check that all the items are included in the package.
MFP_P
RG1 MFP_P
RG2
1 2 3
1 2
Common Criteria
Validated
MFP Data Security Kit
4 5 6
2. Installation
<Note before installation>
• To enable the data security function, the product key must be
acquired. (For the method of acquiring the product key, contact
the dealer.)
• Before installing the data security kit, be sure to perform backup
2) Remove the screw from the right rear cabinet.
of data stored in the memory (including HDD) of the main unit.
3) Remove the right rear cabinet.
When the data security kit is installed, all the job data stored in
the memory (including HDD) of the main unit will be lost. 4) Remove the two screws from the control PWB unit.
• If the LINE indicator or the DATA indicator for the printer and • If the fax box unit is installed, carry out steps 5), 6), and
image transmission on the operation panel is lit or blinking, data 7) additionally.
that has not been processed remains in the memory of the main 5) Pull out the control PWB unit and remove the snap band.
unit (including HDD). Output or transmit all the data to clear the 6) Remove the interface cable from the frame.
data remaining in the main unit and then start installation. (Check 7) Remove the connector.
to insure that neither the LINE indicator nor the DATA indicator
8) Pull out and remove the control PWB unit.
on the operation panel does light up or blink.)
3
<State of switch> 8 6
5
7
OFF ON
4 5
2) After checking that the operation panel has gone out, open the
2
front cabinet and turn the main power switch to the "OFF" posi-
tion.
OFF
C. Mount the data security kit ROMs to the D. Reattach the control PWB and the right rear
control PWB unit. cabinet.
1 Remove the ROMs (PROG1 and PROG2) from the control PWB • If the fax box unit is installed, carry out steps 1), 2), and 3)
and replace them with the data security ROMs (MFP_PRG1 and additionally.
MFP_PRG2). 1) Connect the interface cable to the control PWB unit.
When mounting the data security kit ROMs, insert them to the 2) Push the interface cable into the recessed portion of the sheet
same positions in the same orientations as those before replace- metal on the control PWB unit.
ment until they click and ensure that the inserted ROMs are locked 3) Attach the snap band to the sheet metal of the control PWB
with the sockets. unit.
1
PROG1
PROG2
PCL/BUMON
BARCODE
FAX IMG EXT
PS KANJI
MFP_PRG2
MFP_
PRG2 • If the fax box unit is installed, carry out step 6) addition-
ally.
PRG1
MFP_PRG1 6) Fit the interface cable into the right rear cabinet cover.
MFP_
Hook 1 Hook 2
Hook 3
Hook 4
E. Turn on the main power switch of the main (2) Boot mode operations
unit. Install the DSK firmware as follows.
1) Insert the power plug of the main unit to the outlet. a. Operations and functions of the keys in the boot mode
NOTE: Never press the C (clear) key in the boot mode.
Otherwise, may enter to the mode unrelated to
this procedure.
If, however, the C (clear) key was pressed by
mistake, press the home (MENU) key a few times
to return to the previous mode.
LOGOUT
MENU key
<State of switch>
MENU key Firm Update
OFF ON From USB Memory
Firm Update
2) After 10 seconds from displaying the above error, the following
From USB Memory
display is made.
Fig. Display of the SFU file
Emergency Prog Init 2) Insert the USB memory with the installation or update firmware
Please wait file (SFU file) in it into the USB port of the machine, and press
[OK] key.
1 3) Select the target firmware file (SFU file) by using [UP] key and G. Data security function setting 2
[DOWN] key. 1) When the document filing file is saved before installing the
• When [OK] key is pressed with the directory name dis- data security kit, the files in the HDD are deleted.
played, the control can enter the lower level directory. (How- After installing, therefore, be sure to delete the data area.
ever, one level lower only.) (System setting (Administrator) → Security setting → All data
4) Press [OK] key. area delete)
The selected firmware file (SFU file) is read. (It takes about 2) Restore the saved file data to the machine.
one minute.) 3) Perform product key input, operation check, and initial setting
according to the Operation manual and Note (MX-FR10 only)
packed together with the machine.
Firm Update H. Common criteria authentication label
Reading Data attachment (MX-FR10 only)
1) Attach the common criteria authentication label packed
together to the position shown below.
5) After completion of reading, installation (update) of the firm-
ware is processed.
1. Unpacking
A. Parts included
1 2
No. Packed part names Quantity
1 CD-ROM (For Screen Font) 1
2 Product key sheet 1
NOTE: To set up the PS driver, do not use the CD-ROM which is
included in the MX-PKX1 but use the CD-ROM which is
included in the MX-PBX3.
2. Installation
<Note before installation>
NOTE: To enable PS3, the product key must be acquired. (For
details of the acquiring method of the product key, refer to
the distributor.)
Write down the acquired product key on the product key
sheet and pass it to the user.
B. PS3 check
1) Print the test page in PS3 fonts by the key operation of the
operation panel. (Select the PS font list by the procedures
described in the data list print printer test page of the system
setup guide.)
Check to confirm that printing is made normally.
APPLICATION
NUMBER
MACHINE
SERIAL
NUMBER
PRODUCT
KEY
MX-3100N MX-PKX1 14 – 1
[15] MX-PUX1
MX-3100N
Service Manual
1. Unpacking
A. Parts included
1 2 3
2. Installation
A. Preparation for enabling XPS
1) To enable XPS, enter the product key by the key operation of
the copier machine.
a) Touch [PRODUCT KEY INPUT].
b) Enter the product key with the 10-key, and touch [OK] key.
APPLICATION
NUMBER
MACHINE
SERIAL
NUMBER
PRODUCT
KEY
MX-3100N MX-PUX1 15 – 1
[16] AR-PF1
MX-3100N 3) Remove the
Service power plug of the main unit from the outlet.
Manual
1. Unpacking
A. Parts included
2. Installation
A. Turn off the power switches of the main unit.
1) Turn the power switch located on the operation panel to the
"OFF" position.
<State of switch> 2) Remove the screw from the right rear cabinet.
3) Remove the right rear cabinet.
OFF ON 4) Remove the two screws from the control PWB unit.
• If the fax box unit is installed, carry out steps 5), 6), and
7) additionally.
2) After checking that the operation panel has gone out, open the 5) Pull out the control PWB unit and remove the snap band.
front cabinet and turn the main power switch to the "OFF" posi-
6) Remove the interface cable from the frame.
tion.
7) Remove the connector.
8) Pull out and remove the control PWB unit.
OFF
4
3
8 6
5
7
4 5
2
MX-3100N AR-PF1 16 – 1
C. Installation of the barcode font ROM PWB 6) Fit the interface cable into the right rear cabinet cover.
Install the barcode font ROM PWB to the barcode connector. 7) Attach the right rear cabinet cover to the main unit.
* Check to confirm that the silver push lever extends out when the At this time, check that the four hooks are properly fitted to the
PWB is installed. main unit.
8) Secure the right rear cabinet with the screw.
Hook 1 Hook 2
Hook 3
Hook 4
BOOT
PROGRAM 9) Attach the ozone filter cover to the main unit.
PCL/BUMON
BARCODE
FAX IMG EXT
PS KANJI
ON
MX-3100N AR-PF1 16 – 2
3) Turn on the power switch located on the operation panel.
<State of switch>
OFF ON
G. Font list
Font No. Font name
1 Code128TT-Regular
2 Code128-NarrowTT-Regular
3 Code128-WideTT-Regular
4 Code39HalfInch-Regular
5 Code39OneInch-Regular
6 Code39QuarterInch-Regular
7 Code39SmallHigh-Regular
8 Code39Slim-Regular
9 Code39SmallLow-Regular
10 Code39SmallMedium-Regular
11 Code39Wide-Regular
12 Codabar-Regular
13 Interleaved2of5-Regular
14 Interleaved2of5-Thin-Regular
15 OCR-A
16 OCR-B
17 OCR-B-C39-Regular
18 Upc-Half
19 Upc-Half-Bars
20 Upc-HalfMusic
21 Upc-HalfNarrow
22 Upc-HalfThin
23 Upc-Tall-Regular
24 Upc-TallBarsThin-regular
25 Upc-TallMusicThin-Regular
26 Upc-TallNarrow-Regular
27 Upc-TallThin-regular
28 ZipCodeBarcode-Regular
MX-3100N AR-PF1 16 – 3
[17] MX-NSX1
MX-3100N
Service Manual
1. Unpacking
A. Parts included
1 2 3
2. Installation
<Note before installation>
• To enable the network scanner function, the product key must be
acquired.
• For the models in which the printer and the network function can-
not be used, the expansion memory board must be installed in
advance. (Refer to the Operation Manual attached to the
machine and the Service Manual.)
MX-3100N MX-NSX1 17 – 1
[18] MX-AMX1
MX-3100N
Service Manual
1. Unpacking
A. Parts included
1 2 3
2. Installation
<Note before installation>
• To enable the Application Integration Module function, the prod-
uct key must be acquired.
• The network scanner expansion kit must be installed in advance.
The installing procedure differs depending on the destination.
To install the network scanner expansion kit, refer to the descrip-
tions for the "[17] Network scanner expansion kit (MX-NSX1)" in
this Service Manual.
MX-3100N MX-AMX1 18 – 1
2 : '09/Sep
[19] MX-AMX2
MX-3100N • MX-2600N/MX-3100N
Service Manual
1) By the procedure of A., "OSA setting" key is added to the
menu screen of the system setting or the key operator pro-
1. Unpacking gram.
A. Parts included
1 2
2. Installation
<Note before installation>
* To enable the external account kit, the product key must be
acquired.
MX-3100N MX-AMX2 19 – 1
2 : '09/Sep
D. Selecting a external application (3) Method to select from the function expansion key
2 • MX-2301N/MX-2600G/MX-3100G 1) Press the function expansion key.
There are three methods to select an external application which is * When no external application is registered on the Web
set on the Web screen of the copier: screen, it cannot be used.
The method to select on the basic menu of each mode, the method
to select in the document filing mode, and the method to select with
the function expansion key.
(1) Method to select from the base screen
1) Touch the OSA icon. 2) (When two or more external applications are registered on the
* When no external application is registered on the Web Web screen)
screen, it cannot be touched. Select an external application.
* If only one external application is registered on the Web
screen, it is not required to perform this procedure.
OSA
File Retrieve
File
Folder
Quick File
Folder
2) (When two or more external applications are registered on the
Web screen)
2) (When two or more external applications are registered on the
Select an external application.
Web screen)
Select an external application. * If only one external application is registered on the Web
screen, it is not required to perform this procedure.
* If only one external application is registered on the Web
screen, it is not required to perform this procedure.
App 01
1/2
App 02
App 03
App 04
MX-3100N MX-AMX2 19 – 2
2 : '09/Sep
MX-3100N MX-AMX2 19 – 3
2 : '09/Sep
[20] MX-AMX3
MX-3100N • MX-2600N/MX-3100N
Service Manual
a) By the procedure of 1), "OSA setting" key is added to the
menu screen of the system setting or the key operator
1. Unpacking program.
A. Parts included
1 2
MX-3100N MX-AMX3 20 – 1
[21] MX-FXX2
MX-3100N 3) Remove the
Service power plug of the main unit from the outlet.
Manual
1. Unpacking
A. Parts included
Installation
M3 Screw: directions:
Line cable:
2. Installation
<Note before installation>
• Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
A. Turn off the power switches of the main unit. 3) Insert the step screw into the mounting hole of the fax box unit.
1) Turn the power switch located on the operation panel to the 4) Use a screw that has been removed in step 1) to secure the
“OFF” position. fax box unit.
<State of switch>
OFF ON
2) After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the “OFF” opsi-
tion.
MX-3100N MX-FXX2 21 – 1
2) Remove the screw from the right rear cabinet and remove the E. Attach the interface cable.
right rear cabinet. 1) Connect the interface cable to the control PWB unit.
[Note] Check that the connector is not obliquely inserted.
2) Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.
3) Fix a snap band with the bundled M3 screw.
Screw
BOOT
PROGRAM 3) Fit the interface cable into the opening that has been cut.
PCL/BUMON 4) Attach the right rear cabinet cover to the main unit.
BARCODE
At this time, check that the four hooks are properly fitted to the
FAX IMG EXT
main unit.
PS KANJI
MX-3100N MX-FXX2 21 – 2
5) Secure the right rear cabinet with the screw. H. Set the destination and the logo type.
1) Switch the operation panel to the copy mode and use the key
Hook 1 Hook 2 operation [P], [∗], [C], and [∗] to enter the simulation mode.
Hook 3 2) Use the numeric keys to enter [26] in the main code entry
screen shown below and press the [START] key.
Hook 4
Display Description
U.S.A U.S.A.
CANADA Canada
INCH Inch system, other destinations
JAPAN Japan
AB_B AB system (B5 size detectable), other destinations
EUROPE Europe
U.K. U.K.
2) Turn on the main power switch.
AUS. Australia
AB_A AB system (A5 size detectable), other destinations
CHINA China
ON
<State of switch>
OFF ON
MX-3100N MX-FXX2 21 – 3
I. Clear the FAX related software switches. J. Clear the image memory.
1) Switch the operation panel to the copy mode and use the key 1) Switch the operation panel to the copy mode and use the key
operation [P], [∗], [C], and [∗] to enter the simulation mode. operation [P], [∗], [C], and [∗] to enter the simulation mode.
2) Use the numeric keys to enter [66] in the main code entry 2) Use the numeric keys to enter [66] in the main code entry
screen shown below and press the [START] key. screen shown below and press the [START] key.
3) Use the numeric keys to enter [02] in the sub-code entry 3) Use the numeric keys to enter [10] in the sub-code entry
screen shown below and press the [START] key. screen shown below and press the [START] key.
4) Use numeric keys [0] and [1] to enter the desired 8-digit coun-
try code. 4) In the submenu screen shown below, press [EXECUTE] on the
touch panel.
After entry, press [SET], [EXECUTE], and [YES] in this order.
After [YES] on the panel lights up, press it.
MX-3100N MX-FXX2 21 – 4
K. Connect the line cable to the fax box unit.
1) Connect the line cable of the line side to the modular jack indi-
cated with “LINE.”
ǂǂǂ6,08/$7,21ǂǂ12
7(67 &/26(
0$&+,1(6<67(0
0$&+,1(0;* 360;3.;
563)'63)0;53; ;360;38;
67$03$569 6(&85,7<0;)58
'(6.0;'(; $,00;$0;
),1,6+(50;)1; +''ˆˆˆˆˆ0%
)$;0;);; 1,&67$1'$5'
)$;0;)/; %$5&2'($53)
)$;ǂ0(025<$500 )217$53)
+$1'ǂ6(70;+1; ,17(51(7)$;0;):;
1(7:25.ǂ6&$11(50;16; 23(186%0;$0;
MX-3100N MX-FXX2 21 – 5
[22] MX-FWX1
MX-3100N
Service Manual
1. Unpacking
A. Parts included
1 2
No. Packed part names Quantity
1 CD-ROM 1
2 Product key sheet 1
2. Installation
<Note before installation>
• In order to enable the Internet Fax send function, the product key
must be acquired.
• In order to specify the address of the Internet Fax with the PC-
FAX driver, the PC-FAX driver must be updated by the Internet
Fax expansion kit.
MX-3100N MX-FWX1 22 – 1
[23] MX-SMX3
MX-3100N B. Pull outManual
Service the control PWB.
• If cables are connected to the control PWB unit, remove all
cables.
1. Unpacking
1) Push the location indicated in the illustration to unlock, and
A. Parts included remove the ozone filter cover from the right rear cabinet.
OFF ON
4
2) After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the "OFF" posi-
tion.
3
8 6
5
7
OFF 4 5
2
3) Remove the power plug of the main unit from the outlet.
Installing
position
MX-3100N MX-SMX3 23 – 1
a) Push the sections indicated with → at the same time with D. Reattach the control PWB and the right rear
both hands. cabinet.
* When handling the expansion memory, be careful not to • If the fax box unit is installed, carry out steps 1), 2), and 3)
touch the pin section.
additionally.
* Insert the memory straightly until it comes in contact
1) Connect the interface cable to the control PWB unit.
with the contact.
2) Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.
3) Attach the snap band to the sheet metal of the control PWB
unit.
Hook 1 Hook 2
Hook 3
2) Insert the power plug of the copier into the power outlet. Turn 7
ON the power switch. Hook 4
MX-3100N MX-SMX3 23 – 2
9) Attach the ozone filter cover to the main unit.
ON
<State of switch>
OFF ON
MX-3100N MX-SMX3 23 – 3
COPYRIGHT 2009 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.
Trademark acknowledgements
Microsoft ® Windows ® operating system is a trademark or copyright of Microsoft
Corporation in the U. S.A. and other countries.
Windows® 95, Windows® 98, Windows ® Me, Windows NT ® 4.0, Windows ® 2000,
Windows ® XP, Windows ® Vista, Windows ® 2000 Server, Windows ® Server 2003
and Internet Explorer® are trademarks or copyrights of Microsoft Corporation in the
U.S.A. and other countries.
IBM and PC/AT are trademarks of International Business Machines Corporation.
Acrobat ® Reader Copyright ® 1987 -2002 Adobe Systems Incorporated. All rights
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks
of Adobe Systems Incorporated.
All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Business Solutions Group
CS Promotion Center
Yamatokoriyama, Nara 639-1186, Japan
2009 September Printed in Japan