Professional Documents
Culture Documents
1.0 GI Pipes
1.0 GI Pipes
Impact
Speci- Grade CHEMICAL COMPOSITION % (Max.) MECHANICAL PROPERTIES
Hydrostatic
fication Energy
C.E. YIELD STRENGTH TENSILE STRENGTH % Elongation Test Pressure
C Mn P S Si V Nb Ti Min. Max Min. Max. J Ft/lb
PCM IIW
PSI MPa PSI MPa PSI MPa PSI MPa e min.
API 5L L210 or A 0.22 0.90 0.030 0.030 - - - - - - 30500 210 - - 48600 335 - - U.S Customary - U.S Customary Unit,
Unit P = 2ST / D
PSL-1 L245 or B 0.26 1.20 0.030 0.030 - - - - - - 35500 245 - - 60200 415 - - e = 625,000 S.I Unit
- P = 2000 ST/D
A0.2 /U0.9
S.I Unit S = Fibre Stress in
L290 or X-42 0.26 1.30 0.030 0.030 - - - - - - 42100 290 - - 60200 415 - - - PSI (MPa)
e = 1940
A0.2 /U0.9 = 60% of Min.
L320 or X-46 0.26 1.40 0.030 0.030 - - - - - - 46400 320 - - 63100 435 - - - Y.S for all sizes
Legend : for Grade A & B
e = specified min.
elongation = 60% of Min.Y.S
L360 or X-52 0.26 1.40 0.030 0.030 - - - - - - 52200 360 - - 66700 460 - - -
A= Tensile test for all sizes
piece cross <5 9/16" for
L390 or X-56 0.26 1.40 0.030 0.030 - - - - - - 56600 390 - - 71100 490 - - sectional area. - Gr. X-42 & above.
U= Specified min. = 75% of Min.
L415 or X-60 0.26 1.40 0.030 0.030 - - - - - - 60200 415 - - 75400 520 - - tensile strength. Y.S for size
-
> 5 9/16" &
< 8 5/8" for
L450 or X-65 0.26 1.45 0.030 0.030 - - - - - - 65300 450 - - 77600 535 - - - Gr. X-42 & above.
= 85% of Min.
L485 or X-70 0.26 1.65 0.030 0.030 - - - - - - 70300 485 - - 82700 570 - - - Y.S for size
>8 5/8" &
27 (20) <20" for
API 5L L245M or BM 0.22 1.20 0.025 0.015 0.45 0.050 0.050 0.040 0.25 0.43 35500 245 65300 450 60200 415 110200 760
Gr. X-42 & above.
= 90% of Min. Y.S
PSL-2 L290M or X42M 0.22 1.30 0.025 0.015 0.45 0.050 0.050 0.040 0.25 0.43 42100 290 71800 495 60200 415 110200 760 27 (20) for size >20" for
Gr. X-42 & above.
L320M or X46M 0.22 1.30 0.025 0.015 0.45 0.050 0.050 0.040 0.25 0.43 46400 320 76100 525 63100 435 110200 760 27 (20) Std. Test pressure
limited to 2970 PSI
(20500 kpa) for
L360M or X52M 0.22 1.40 0.025 0.015 0.45 - - - 0.25 0.43 52200 360 76900 530 66700 460 110200 760 27 (20) Gr. X-42 & above.
Alternate test pressure
L390M or X56M 0.22 1.40 0.025 0.015 0.45 - - - 0.25 0.43 56600 390 79000 545 71100 490 110200 760 27 (20) limited to 7260 PSI
(50000 kpa) for size
27 (20) <16," & 3630 PSI
L415M or X60M 0.12 1.60 0.025 0.015 0.45 - - - 0.25 0.43 60200 415 81900 565 75400 520 110200 760
(25000 kpa) for size
>16" for Gr. X-42
L450M or X65M 0.12 1.60 0.025 0.015 0.45 - - - 0.25 0.43 65300 450 87000 600 77600 535 110200 760 27 (20) & above
P = 2000 ST/D
L485M or X70M 0.12 1.70 0.025 0.015 0.45 - - - 0.25 0.43 70300 485 92100 635 82700 570 110200 760 27 (20) (limited to 19.3 MPa),
S for YST 210 = 124
for Std. Pressure,155
IS:1978 YST - 210 0.22 0.90 0.040 0.050 - - - - - - - 210 - - - 330 - - e = 1942.57 for ALT pessure ;
A0.2 /U0.9 S for YST 240 =145
YST - 240 0.27 1.15 0.040 0.050 - - - - - - - 240 - - - 410 - - for Standard Pressure,
181 for ALT pressure,
IS:1979 YST - 290 0.28 1.25 0.040 0.050 - - - - - - - 290 - - - 410 - - P = 2000 S T/D
or 20700 KPA
YST - 320 0.30 1.35 0.040 0.050 - - - - - - - 320 - - - 430 - - whichever is smaller
where S= Fibre stress
e = 1942.57 in MPA equal to % of
YST - 360 0.30 1.35 0.040 0.050 - - - - - - - 360 - - - 450*/500** - - SMYS for various
A0.2 /U0.9
sizes as below :
YST - 390 0.26 1.35 0.040 0.050 - - - - - - - 390 - - - 490*/520** - - Size
114.3 mm OD or
less = 60%
YST - 410 0.26 1.35 0.040 0.050 - - - - - - - 410 - - - 520*/540** - -
168.32 to 219.1 mm
OD = 75%
YST - 450 0.26 1.40 0.040 0.050 - - - - - - - 450 - - - 530*/550** - - 273.0 to 457.2 mm
OD = 85%
YST - 480 0.23 1.60 0.040 0.050 - - - - - - - 480 - - - 565 - - 508 mm OD and
large = 90%
* Applicable for pipes with < 508 mm OD and any wall thickness, and pipe with 508 mm and larger, and wall thickness > 9.5 mm P = 2 ST / D or
** Applicable for pipes with 508 mm OD and larger wall thickness < 9.5 mm 2800 PSI (19.3 MPa)
whichever is smaller
S = 0.60 times min.
specified Y.S PSI (Kpa)
ASTM A 0.25 0.95 0.050 0.045 - - - - - - 30000 205 - - 48000 330 - - e = 625,000
A0.2 /U0.9 P = 2ST / D shall not
exceed 5 MPa
A- 53 B 0.30 1.20 0.050 0.045 - - - - - - 35000 240 - - 60000 415 - - S = Stress which shall
be taken 60% of min.
G.L.= 5.65 area specified Y.S
IS:3589 Fe 330 0.16 1.20 0.040 0.040 - - - - - - - 195 - - - 330 - -
20
Fe 410 0.20 1.30 0.040 0.040 - - - - - - - 235 - - - 410 - - 18
15
Fe 450 0.25 1.20 0.040 0.040 - - - - - - - 275 - - - 450 - -
API 5CT H 40 - - 0.030 0.030 - - - - - - 40000 276 80000 552 60000 414 - - e = 625,000 20L/16T P = 2 ( f x yp x T ) / D
A0.2 /U0.9 f = a Factor,
J-55 - - 0.030 0.030 - - - - - - 55000 379 80000 552 75000 517 - - 27L/20T 0.8 for < 9 5/8"
& 0.6 for >9 5/8"
L= long. YP= Specified Min.
T= Trans. Yield Strength (PSI)
NOTE : Refer current edition of Relevant specification for Dimensions and Properties data A = Specimen cross-sectional area P = Test pressure PSI (MPA)
U = Specified Min. T.S. T = Specified wall thickness
* Specifications are subject to change without any prior notice D = Specified Outside Diameter.
Corporate Office:
Plot No. 30, Institutional Sector -44, Gurgaon-122 002, Haryana (India) Tel.: +91 124 2574325 / 26, 4624000 Fax: +91 124 2574327
e-mail: contact@mahaseam.com
# 10-030/ MSL
Website: www.jindal.com
Regd.Office & Works:
Pipe Nagar, Village Sukeli, N.H.-17, B.K.G. Road, Distt. Raigad - 402 126, Maharashtra (India) Tel.: +91 2194 238511 /12 /16 Fax: +91 2194 238513
e-mail: seamless@sancharnet.in
Branch Office:
Mumbai : 402, Sarjan Plaza, 100, Dr. Annie Besant Road, Opp. Telco Show Room, Worli, Mumbai - 400 018 (India) Tel.: +91 22 24902570 /72 /74 Fax : +91 22 24925473
e-mail: mslmum@mtnl.net.in
Chennai : 3A, Royal Court, No-44, 3rd Floor, Venkatanarayana Road, T. Nagar, Chennai - 600 017 (India) Tel.: +91 44 24342231, 24328747 Fax : +91 44 24347990
e-mail: chennai@mahaseam.com
Kolkata : Sukh Sagar Apartment, Flat No. 8 A&B, 8th Floor, 2/5 Sarat Bose Road, Kolkata -700 020 (India) Tel.: +91 33 24559982,32588626 Fax : +91 33 24742290
e-mail: kolkata@mahaseam.com