Professional Documents
Culture Documents
د حيدر محمد علي نور علي عباس
د حيدر محمد علي نور علي عباس
د حيدر محمد علي نور علي عباس
A Project Submitted to
The College of Dentistry, University of Baghdad, Department
of Orthodontics in Partial Fulfillment for the Bachelor of
Dental Surgery
By
Supervised By:
May 2022
Certification of the Supervisor:
I
Dedication
This study is wholeheartedly dedicated to my beloved parents,
who have been my source of inspiration and gave me strength when i
thought of giving up, who continually provide their moral, spiritual,
emotional, and financial support, to my brothers, sister, friends, and
classmates who shared their words of advice and encouragement to
finish this study.
II
Acknowledgement
III
Table of Contents
IV
3.2. Plastic brackets 11
3.3 .Ceramic brackets 12
4. Classification of the brackets according to slot size 13
Table of Contents
5. Brackets prescription 13
5.1. Standard edgewise brackets 13
5.2. The preadjusted edgewise brackets 14
5.2.1. Andrew Prescription 14
5.2.2. Alexander prescription 15
5.2.3. Ricketts prescription 16
5.2.4. Roth Prescription 16
5.2.5. MBT Prescription 20
5.2.6. Damon Brackets 23
5.2.7. Customized brackets 27
Chapter Two
Discussion 30
Chapter Three
Conclusions 33
Suggestions 35
References
References 36
V
List of Figures
VI
List of Tables
List of abbreviations
Abbreviation Deceptive
SL Self-ligating
SWA Straight wire appliance
VII
Introduction
Brackets act as handles to transmit the force from the active components to the
teeth, the aim of this review is to spotlight the orthodontic brackets and the way they
assist the orthodontist to offer better treatment aesthetically, orthodontic brackets are an
important component in order to deliver the precise force from the wire to the teeth,
brackets should have the right hardness and strength, they ought to have a smooth arch
wire slot to scale back frictional resistance and an otherwise `smooth surface to scale
back plaque deposition (Kannan et al., 2020).
Orthodontic patients, including a growing population of adults, not only want an
improved smile, but they also want better aesthetics during treatment, the development of
appliances that combines both acceptable aesthetics for the patient and adequate technical
performance for the clinician is the need of the hour, there has been a recent trend
towards the development of smaller stainless steel brackets but although these generally
provide the technical performance required by the orthodontist the aesthetic advantage
over conventionally sized appliances is limited (Kakadiya et al., 2017).
With time so many clinicians put forward their own prescriptions of brackets, for
effective use of these prescriptions many of them also advocated their own treatment
mechanics and bracket position on teeth, some of these prescriptions were also even
disowned after copyright of the patent was expired, other prescriptions were changed
with time after hit and trials reveals the flaws within them, in many cases same
prescription vary between different bracket manufacturers, order to avoid copyright and
patent violation many manufacturers produce the same prescription with minor changes
in tip and torque values, even different values in 0.018” and 0.022” slots of same
prescription are sold by the manufacturers,this is due to more clearance between wire and
slot in 0.022” slot so 0.022” slots are sometimes made in higher torque values than 0.018
“ slot (Proffit et al., 2000).
1
Many text books of orthodontics show charts containing only tip and torque and no
importance is given to counter rotation and mesial offset,some bracket sold in the markets
have prescriptions which are never endorsed by any clinician, meaning manufacturers
also make their own prescriptions (Sernetz, 1993).
2
Aims of the study
The aims of the study are to answer one simple question:
(What is the best prescription for every case? Is it a single prescription or hybrid?).
And this question will be answered by reviewing different bracket prescriptions in order
to reach a goal of choosing the best prescription for every patient that facilitates the
orthodontist work.
3
Chapter one
Review of literatures
1. Definitions
1.1. Brackets
Orthodontic brackets are important part of fixed appliances which are temporarily
attached to the teeth during the course of orthodontic treatment; they are used to deliver
forces from the wires or other power modules to the teeth (Khans, 2015).
4
1.3. Torque or Crown inclination (labiolingual or buccolingual inclination)
It was is inclination of long axis of clinical crown (LACC), crown inclination is
measured by angle formed by a line tangent to the middle of the labial or buccal long axis
or facial axis of the clinical crown (LACC or FACC) and a line that is 90° to the occlusal
plane, Crown inclination is measured in degrees with positive or negative sign, a positive
sign is given when gingival portion of the tangent line or gingival portion of crown is
lingual or palatal to the incisor portion, a minus or negative sign is given when gingival
portion of the tangent line or gingival portion of crown is buccal or labial to the incisor
portion (Dolci et al., 2013).
2. History
The origin of orthodontic brackets can well be coined with the origin of
orthodontics and the human desire to align crooked teeth, the first written record to
correct crowded or protruded teeth is found 3000 year ago (Weinberger, 2001).
Orthodontic appliances to correct maligned teeth have been found in Greek,
Etruscan and Egyptian artifacts, these ranges from crude metal wire loupes to metal
bands wrapped around individual teeth in ancient Egyptian mummies (Wahl, 2005).
Pierre Fauchard (1678 –1761) a French dentist was the first to make a scientific
attempt to align irregular teeth by an appliance named Bandeau, this appliance was made
of precious metal and it was shaped like a horse shoe to align teeth by arch expansion,
5
another French dentist used swelling threads and wooden wedges to separate crowded
teeth, Horace H. Hayden (1769-1844) invented bands with soldered knobs to correct
tooth rotation, in 1803, Joseph Fox invented a modified version of bandeau appliance that
consisted of silver or gold rim, Harris in 1850 attached metal caps to molar and took
anchorage from palate in his expansion appliance (Chapman, 1955).
Edward Hartley Angle (1855-1930) was the most dominant and influential figure
in orthodontics and is regarded as the “Father of Modern Orthodontics.” Angle developed
four major orthodontic appliance systems which lay the basis of contemporary fixed
braces (Asbell, 1990). These appliances were:
2.1. E Arch
The first device developed by Angle was E arch in late 1890s, this appliance was in
fact a mix of ideas from previous expansion appliance, in this appliance a heavy labial
arch extends around the arch with the end of the wire threaded and placed in the molar
bands (Asbell, 1990).
6
Figure (4) Pin and tube appliance (Weinberger, 2001).
7
Figure (6) Edgewise appliance (Cross, 1996).
2.5. Labiolingual twin Wire
Which used bands on first molars and a combination of heavy lingual and labial
archwires to which finger springs were soldered to move individual teeth, and the twin-
wire appliance (Kim et al., 2010).
9
active and passive ligating brackets depending upon the mechanism of closure of ligating
clip and holding the wire in slot (Stolzenberg, 2003).
10
3. Classification of the brackets according to materials
Ideal bracket in terms of material prospective should have following qualities:
Biocompatible in oral environment, low cost , high modulus of elasticity , high corrosion
resistance , no magnetic properties, no friction on bracket wire interaction , correct
strength and hardness , resist staining and discoloration in oral environment , resist
plaque deposition, and meet patient aesthetic demands (Matasa, 2003).
3.1. Metal Brackets
A. Advantages
Less expensive, sterilized and recycled, resist deformation and fracture, exhibit
least friction at the wire bracket interface (Kannan et al., 2020).
B. Disadvantages
Not aesthetically pleasing, patient tends to have a metallic smile, they can corrode
and cause staining of teeth (Kannan et al., 2020).
There are four main types of metal brackets used in modern orthodontics, these are:
a. Stainless steel brackets b. Cobalt chromium brackets
c. Titanium brackets d. Precious metal brackets
11
Advantages
They were introduced to improve the aesthetic value of the appliances, plastic
brackets are available in tooth colored or transparent forms (Douglass, 1989).
Disadvantages
Discolor particular in patients who smoke or drink coffee, poor dimensional
stability, slots tends to distort, the friction between plastic brackets and metal arch wire is
higher than metal of stainless steel brackets (Kannan et al., 2020).
Advantages
Superior aesthetic, high wear resistance and better color stability over the plastic
brackets, because of short coming of plastic brackets ceramic brackets have gained
increased interest especially in adults, ceramic brackets are inert and can safely be
bonded in patients with nickel and chromium allergy (Michalske et al., 1986).
Disadvantages
Ceramic brackets provide high bond strength, Due to increase hardness there is
difficulty in debonding, more chances of enamel damage and bracket fracture on
debonding and tooth attrition, discoloration of ceramic brackets also occurs in cases with
12
longer treatment time and due to stress corrosion, ceramic, being the 3rd hardest material
is harder than stainless steel wires, ceramic brackets are radiolucent and so can't be
detected by x rays if accidentally aspired or swallowed during debonding (Michalske et
al.,1986).
4. Classification of the brackets according to slot size
1. Slot size 0.018 2. Slot size 0.022
Usually clinician who favor loop mechanics for space closure prefer 0.018” slot
while clinician who choose sliding mechanics for space closure favor 0.022” slot, as
0.018” slot is more efficient in torque expression, cases requiring greater torque
expression are usually treated with 0.0.18” slot brackets, such case included class II div2,
surgical case requiring decompensation and growth modification cases, according to a
survey 54% of orthodontists prefer 0.022 inch slot size, 40.5% used 0.018 inch slot and
5% used a combination of above slots (biodimensional mechanics) or some other bracket
style, to decrease confusion in selection of slot size there are increased efforts by some
orthodontists to bring uniformity in slot size and give it a standard measuring unit
(Swartz, 2001).
Figure (14) Slot size 0.018 and Slot size 0.022 (Al-Huwaizi, 2021).
5. Brackets prescription
5.1. Standard edgewise brackets
The brackets having no built in in/out, tip and torque are called standard edgewise
brackets introduced by Angle, It was proposed that this appliance does not require wire
13
bending during treatment hence the name Straight wire appliance (SWA) was given to it
(Andrews, 1989).
5.2. The preadjusted edgewise brackets
Have tip, torque, in and out bends built within the brackets, it was believed that
these appliances don't require wire bending hence the name Straight wire appliance was
given to them (Weinberger, 2001).
Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip
Maxillary +7 +5 +3 +9 -7 +11 -7 +2 -7 +2 -9 +5 -9 +5
Arch
Mandibular -1 +2 -1 +2 -11 +5 -17 +2 -22 +2 -30 +2 -35 +2
Arch
14
5.2.2. Alexander prescription
Alexander's prescription by R.G. “Wick” Alexander (1978) using 0.018” slot
brackets and 0.017x0.025” wire Alexander advocated individualizing bracket positioning
for each patient to effectively use his bracket prescription, R. G. Wick Alexander
developed the vari simplex discipline in 1978, the „vari‟ indicates the variety of brackets
used, „simplex‟ signifies the principle of, Keep It Simple Sir, and discipline‟is to reflect
the idea that orthodontist must be knowledgeable in edgewise
mechanics (Alexander, 1983).
Bracket selection
Each tooth has a particular bracket that is most effective (Al-Zubair, 2015)
1. Twin Brackets (Diamond brackets): are used on large, flat surfaced teeth maxillary
central and lateral incisors
2. Lang Brackets: were invented by Howard Lang, used with the Diamond design on
large, round-surfaced teeth at the corners of the arch – maxillary and mandibular cuspids
3. Lewis Brackets: are used on large, round-surfaced teeth that are not at the curve of the
arch maxillary and mandibular bicuspids and on small flat surfaced teeth –mandibular
incisors
4. Other Attachment: Twin brackets with a convertible sheath are used on maxillary and
mandibular first molars, which are usually banded, the convertible sheath is easily
removed when second molars are banded, converting the attachment to a bracket
16
II. Overcorrection, especially in torque of brackets to accommodate relapse and
diminution of force
III. Leveling of curve of spee to some extent by placing anterior brackets more incisal
IV. More torque in anterior brackets to accommodate torque loss by wire play
V. Super torque brackets for rapid correction of torque in class II div2 cases
VI. Roth proposed a new arch form called Tru-Arch to be used with his prescription;
Roth advocated selection of arch wire is important as it effects the rotational position of
teeth
VII. Different translation philosophy, according to Roth tipping of the teeth to some
extent is accepted on round wires
VIII. Many auxiliary features were added to brackets such as double and triple tubes,
addition of hooks for ease of mechanics
Maxillary arch:
1. Incisors
Roth3 justified his prescription by explaining that 5° extra torque was added to
maxillary incisors keeping is line with his treatment philosophy of over correction and
accommodating torque loss by wire play so without moving to full dimension wires the
clinician can attain natural inclination of incisors (Roth, 1981).
2. Canine
For canines, Roth used -2° torque which was -5° less than Andrew prescription,
this was done to avoid reactionary effect of building more positive torque into the
incisors brackets, the final torque of canine would be -7° due to reactionary forces from
the wire and because of wire play, also canine tip was increased by +2° to accommodate
tip loss in extraction cases as distal translation of canine take place and it is also helpful
to get better canine guidance (Wadhwa, 2004).
2. Premolars
Both first and second premolar tip was taken from minimum translation series
brackets requiring mesial translation, premolar torque was taken from Andrew standard
17
SWA, Counter rotation feature was taken from minimum translation series brackets for
distal translation (Wadhwa, 2004).
3. Molars
On 1 and 2 molars buccal root torque was increased from -9° to -14°, the increased
torque can counter the effect of hanging of mesiolingual cusp on translation, so 0°tip was
in fact 5° tip of Class I molar, otherwise actually giving a 0° tip to molars in class I
position will result in poor angulation of molars (Roth, 1987).
Mandibular arch
Roth justification not much was changed from Andrew's in Roth prescription in
lower dentition. Canine angulation was increased 2° in an effort to give canine guidance
and give better canine class I relationship, distal tip and distal rotation was introduced in
lower prescription because Roth believe that lower teeth settle more mesial than upper
and also rotate while settling so using modifications will counter the relapse factor, both
the lower molars have same torque, decreasing the tip in lower arch would also decrease
the anchorage demands. Roth proposed that as his appliance rest on mesiobuccal cusp
rather than buccal groove so same torque on molars is justified (Roth, 1981).
In super torque prescription only the lower canine's brackets are present, tip was
maintained at norms while positive root torque was added to canine, this prescription
values is only suited when the upper laterals and canines have pushed the lower canine
inward. In that case usually the lower canine root is more labial and crown is lingual, the
super torque prescription of Roth was indeed genius innovation and it will help to correct
upper incisor inclination in less time but full torque expression built within the brackets
should be avoided (Roth, 1987).
18
Table(4) Roth Prescription (Profit et al., 2012)
Teeth Central Lateral Canine 1st 2nd 1st molar 2nd molar
incisors incsors premolar premolar
Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip
Maxillary 12 5 8 9 -2 9 -7 0 -7 0 -14 0 -14 0
Arch
Mandibular 0 0 0 0 -11 7 -17 0 -22 0 -30 1 -30 0
Arch
Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip
19
III. Root Parallelism
Like Andrew prescription Roth prescription also has problem with root parallelism
especially in maxillary canines, the canine root comes very close to the premolar root
after expression of tip, though it is claimed that not all the tip would be expressed
because of wire play, yet wire play is less a problem with tip than torque (Jain et al.,
2013).
22
placement position in Andrew and MBT prescription, so tip values for molars are same as
Andrew standard SWA (Usmani et al., 2002).
Table (6) MBT Prescription (Profit et al., 2012)
Teeth Central Lateral Canine 1st 2nd 1st molar 2nd molar
incisors Incisors premolar Premolar
Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip Torque Tip
Maxillary 17 4 10 8 -7 9 -7 0 -7 0 -14 0 -14 0
Arch
Mandibular -6 0 -6 0 -6 3 -12 2 -17 2 -20 0 -10 0
Arch
2. DAMON 2 Brackets
Damon 2 brackets (Ormco Corp.) were introduced to address the imperfections of
Damon SL, Combined with the introduction of metal injection moulding manufacture &
slight design changes, Damon 2 brackets are almost completely free from inadvertent
slide opening or slide breakage, however, the brackets were not immediately and
consistently very easy to open (Mizrahi, 2006).
23
Figure (16) DAMON 2 Brackets (Mizrahi, 2006).
Damon Prescription
Ul - Upper Central Incisors
+12° Torque +5° Tip 0° Rotation:
• The standard torque prescription selected when central incisors are in good position
with minimal requirements for treatment mechanics +17° Torque +5° Tip 0° Rotation:
• Selected for division 2 cases
• Cases needing extensive Class II elastics - prevents loss of torque control resulting from
elastic wear +7° Torque +5° Tip 0° Rotation
24
• Centrals requiring extensive uprighting
• Case needing extensive Class III elastics - prevents loss of torque control resulting from
elastic wear (Damon et al., 2003).
U2 - Upper Lateral Incisors:
+8° Torque +9° Tip 0° Rotation:
• The standard torque prescription selected when central incisors are in good position
with minimal requirements for treatment mechanics +10° Torque +9° Tip 0° Rotation:
• Selected for division 2 cases +3° Torque +9° Tip 0° Rotation:
• Laterals requiring extensive uprighting
• Lateral incisors that are blocked in lingual crossbite that will have too much torque as
they move into normal position (Mizrahi, 2006).
U3 - Upper Cuspids:
0° Torque +6° Tip 0° Rotation:
• The standard torque prescription selected when the cuspids are in good position or
labially inclined +7° Torque +6° Tip 0° Rotation;
• Any cuspid needing coronal uprighting
• Most extraction cases requiring first bicuspid space closure - prevents the cuspid crown
from tipping lingual during space closure and helps position the root in medullary bone
and away from the cortical plate (Kakadiya, 2017).
26
• The standard torque prescription selected for all lower second bicuspids (Mizrahi,
2006).
L6 - Lower First Molars:
-30° Torque +2° Tip 0° Rotation
• The standard torque prescription selected for all lower first molars
(Damon et al., 2003).
L7 - Lower Second Molars:
-10° Torque 0° Tip 5° Rotation
• The standard torque prescription selected for all lower second molars (Second molars
usually require uprighting - using -10° torque with 7° of tube and archwire play finishes
the second molar at a net 17° to 18°) (Damon et al.,2003).
28
Table (7) Bracket/Tube Prescription: Incisors Through Premolars, Brackets
Prescription (Proffit et al., 2012).
29
Chapter two
Discussion
Before the invention of the SWA, the bends were made in to the arch wire and
that will be time consuming, required skills, difficult to control tooth movement and the
finishing will be more difficult and less efficient.
The preadjusted edgewise brackets have tip, torque, in and out bends built within the
brackets, it was believed that these appliances don't require wire bending hence the name
Straight wire appliance was given to them (Weinberger, 2001).
However, after invention of the SWA, the tip, the torque values were built in the
brackets itself and that was the beginning of the new era.
We still don't have a prescription where a straight wire is used throughout the
treatment and no wire bending is required. Also lack of consensus on ideal position of the
bracket on the tooth limits the adaptation of a single prescription universally (Jain et al.,
2013).
Tip expression depends on the arch wire stiffness (the stiffer the wire, the more tip
expression), material, width and size of the brackets (good materials that will not be
deformed easily and the larger the brackets with small inter-brackets distance will express
the tip more and more), slot size whether we use 0.018 slot or 0.022 slot (the 0.022
require higher gauge to expree the tip).
Toque expression depends on arch wire stiffness (the stiffer the more toque
expressed), arch wire fitness (play, arch wire size and slot depth), brackets quality, slot
size and over correction.
It is clear that if the entire torque built within the bracket is expressed on
engagement of full dimension wires, the final inclination of incisors would be same no
matter from where one started (Moesi et al., 2013)
0.018 slot brackets allow full engagement of the wire which is a good choice in
non-extraction cases and a crossbite of a lateral incisor.0.022 slot brackets allow plays for
30
sliding and allow larger stiffer wires which are excellent in extraction cases and en mass
retraction.
Andrew advocated using full dimension rectangular wires for final expression of
torque, but there are some practical limitations of using full dimension wires in the slot,
Roth work was not an innovation rather it was awise selection of brackets from Andrews'
work that favors mechanics used by Roth on most of the patients he treated at his office,
Roth humbly named his prescription as Roth prescription of Andrew appliance, all the
prescriptions work fine if one follows the inventor's advocated mechanics, all the
prescriptions have their own limitations that needed to be compensated by wire bending
or elastics to some extent, we still don't have a prescription where a straight wire is used
throughout the treatment and no wire bending is required, also lack of consensus on ideal
position of the bracket on the tooth limits the adaptation of a single prescription
universally during treatment (Moesi et al., 2013).
Dr. Ricketts used a .0185 x .030-inch slot bracket for ease of wire placement and
use of overlaid arches, the concept of utility arch and sectional arches was first evolved
by Ricketts With time so many clinicians put forward their own prescriptions of brackets,
for effective use of these prescriptions many of them also advocated their own treatment
mechanics and bracket position on teeth, the increase in quality also comes with an
increase in its cost, the orthodontist should wisely choose which bracket system would be
best for the chosen case and also fulfill the aesthetics requirements of the patient, all the
prescriptions work fine if one follows the inventor's advocated mechanics, all
theprescriptions have their own limitations that needed to be compensated by wire
bending or elastics to some extent (Saxe et al., 2010).
We still don't have a prescription where a straight wire is used throughout the
treatment and no wire bending is required, also lack of consensus on ideal position of the
bracket on the tooth limits the adaptation of a single prescription universally (Wahl,
2005).
31
Summary of Roth Appliance one set upper and lower canines with more tip
(Overcorrection),upper anterior teeth with more torque (Overcorrection),decreased tip in
both upper and lower buccal segment (Anchorage),upper molars with less torque (Molar
control) Summary of MBT Appliance one set, less tip on upper and lower anterior teeth,
proclined upper incisors, retroclined lower incisors, upright lower buccal teeth.
Damon system has high torque. Damon SL brackets (“A Company, San Diego,CA)
had a slide that wrapped around the labial face of the bracket (Kakadiya, 2017).
Damon 2 brackets (Ormco Corp.) were introduced to address the imperfections
of Damon SL, Combined with the introduction of metal injection moulding manufacture
& slight design changes, Damon 3 and Damon 3MX brackets (Ormco corp.) have a
different location and action of the retaining spring, and this has produced a very easy
and secure mechanism for opening and closing (Mizrahi, 2006).
A customized appliance system uses digital models of the patient’s arches to
simulate the optimal position of each dental element and the ideal final occlusion, once
the desired virtual result is achieved, the personalized archwires, brackets, and indirect-
bonding transfer jigs are produced (Saxe et al., 2010).
Clinician should choose a prescription in which they find ease with mechanics
advocated for that prescription, due to various limitation of all prescription some degree
of wire bending and bracket position alteration is always required and clinician should
remain mentally prepared for that, all the cases must be finished in light of Andrews' six
keys or any other parameters set by local examination bodies or ethical councils (Jain et
al., 2013).
32
Chapter three
Conclusions and suggestions
Conclusions:
1. The brackets having no built in in/out, tip and torque are called standard edgewise
brackets, mean (Tip and Torque zero), then straight wire appliance were developed that,
have tip, torque, in and out prescription built within the brackets.
2. Preadjusted brackets have tip, torque, in and out bends built within the brackets, it was
believed that these appliances don't require wire bending hence the name Straight wire
appliance
3. Andrew prescription, the first preadjusted brackets where all the bending's needed in
arch wire in standard edgewise bracket system were built within the brackets, it was
proposed that this appliance does not require wire bending during treatment hence the
name Straight wire appliance
4. 0.018 slot size that enable full engagement the wire is easier for torque with stainless
steel wires and give more control for torque than 0.022 slot size, 0.022 slot size allows
play for sliding wire and allows larger stiffer wire.
5. Alexander's prescription, using 0.018” slot brackets and 0.017x0.025” wire Alexander
advocated individualizing bracket positioning for each patient to effectively use his
bracket prescription.
6. Dr. Ricketts used a .0185 x .030-inch slot bracket for ease of wire placement and use
of overlaid arches, the concept of utility arch and sectional arches was first evolved by
Ricketts.
7. Roth Appliance set upper and lower canines with more tip (Overcorrection), upper
anterior teeth with more torque (Overcorrection),decreased tip in both upper and lower
buccal segment (Anchorage),upper molars with less torque (Molar control).In conclusion
less torque and more tip used Roth prescription.
33
8. MBT Appliance set has, less tip on upper and lower anterior teeth resulted in,
proclined upper incisors, retroclined lower incisors, upright lower buccal teeth in
conclusion more torque and less tip used MBT Prescription.
9. In Damon system depends on early using of elastics, expansion, stripping and more
torque.
10. Customized brackets allows to see the teeth straightened in the virtual setup, and
brackets are then designed to be placed on ‘‘straight teeth’’ in the desired final
relationship with an unbent wire.
34
Suggestions:
1. Conduct a survey study to see the most common bracket prescription used in the
college of dentistry, university of Baghdad clinics, and the possibility of using hybrid
prescription.
2. Conduct a clinical trial study to see the tip effect of different bracket prescriptions of
canine during leveling stage of the fixed orthodontics treatments.
3. Compare the different brackets materials with the prescriptions to find out the effect of
good materials on the expression of the tip and torque.
4. Dig deep in literatures that concern about customized brackets.
5. Digital orthodontics is a new area that I highly suggested to cover it in the future
research projects of the undergraduate students.
35
References
(A)
1. Alexander, RG. (1983) The vari-simplex discipline. Part 1. Concept and appliance
design. J Clin Orthop.17:380–392.
2. Akram Al-Huwaizi.(2021) Understanding Brackets Prescription, YouTube video.
3. Andreiko (2011) 3D interactive treatment planning and patientspecific
appliances, in Lingual & Esthetic Orthodontics, ed.R. Romano, Quintessence,
Hanover Park, IL, pp. 157-166.
4. Andrews LF. (1989) Straight-Wire-The Concept and Appliance; L. A. WellsCo.,
San Diego,California. 92107.
5. Andrews LF. (1972) the six keys to normal occlusion. Am J Orthod ; 62:296-
309**
6. Antonio Gracco, DDS ,Stephen Tracey, DDS, MS. (2011) the Insignia System of
Customized Orthodontics.
7. Asbell MB.(1990) A brief history of orthodontics. Am J Orthod DentofacialOrthop
;98:176-83.
8. Ashish Kakadiya, Ragni Tandon, Aftab Azam.(2017)”Recent advancements in
orthodontic brackets” .
(B)
9. Begg PR.(1956) Differential force in orthodontic treatment. Int J Orthod ;42:481-
489.
10. Brandt S. (1979) JCO interviews Elliott Silverman, Morton Cohen, and A. J.
Gwinnett on bonding. J Clin Orthod ; 13:236-51.
(C)
36
13. Cross JJ. (1996) The Tweed philosophy: the Tweed years. Semin Orthod, Dec;
2(4):231-6.
(D)
(E)
(F)
(H)
20. Haris Khans.(2015) “orthodontics brackets selection, placement, debonding”.
(J)
37
21. Jain M, Varghese J, Mascarenhas R, Mogra S et al.(2013) Assessment of clinical
outcomes of Roth and MBT bracket prescription using the AmericanBoard of
Orthodontics Objective Grading System.Contemp Clin Dent. Jul;4(3):30712.
22. Johnson JE.(1934) Twin wire alignment appliance. Int J Orthod ;20:946-963.
(K)
23. Kannan , Nandhini ,Padmavati.” Brackets In Orthodontics” , Vol 07,2020.
24. Kapur-Wadhwa R.(2004) Physical and mechanical properties affecting torque
control. J Clin Orthod. Jun;38(6):335-40.
25. Kesling CK.(1989) Differential anchorage and the Edgewise appliance. J Clin
Orthod. Jun;23(6):402-9.
26. Kim SH, Kang SM, Choi YS, et al.(2010) Cone-beam computed tomography
evaluation of mini-implants after placement: is root proximity a major risk factor
for failure? Am J Orthod Dentofac Orthop 138:264-276.
27. Kusy R, Whitley J.(1999) Assessment of secondorder clearances between
orthodontic archwires and bracket slots via the critical contact angle for binding.
Angle Orthod. ;69:71–80.
(L)
28. Lewis PD. (1950) Space closure in extraction cases. Am J Orthod ;36:172-91.
(M)
29. Matasa C.(2003) Characterization of used orthodontic brackets. In: Eliades G,
Eliades T, Brantley WA, Watts DC, eds. Dental Materials in Vivo:Aging and
Related Phenomena. New York, NY: Quintessence; 141–156.
30. Mclaughlin RP, Bennett JC, Trevisi H.(2005)Systemized Orthodontic Treatment
Mechanics. New York:Mosby.
31. Michalske TA, Bunker BC, Freiman SW.(1986) Stress corrosion of ionic and
mixed ionic/covalent solids. J Am Ceram Soc. ;69:721–724.
32. Moesi B, Dyer F, Benson PE.(2013) Roth versus MBT: does bracket prescription
have an effect on the subjective outcome of pre-adjusted edgewise treatment? Eur J
38
Orthod. Apr;35(2):236-43.
(N)
33. Nabil muhsen al-zubair. (2015) alexander orthodontic philosophy.
(P)
34. Paul H. Ling.(2005) Lingual Orthodontics: History, Misconceptions and
Clarification. J Can Dent Assoc 71:2:99–102.
35. Power S, Irvine R, McDonald F.(2004) The effectiveness of laceback ligatures: a
randomized controlled clinical trial. J Orthod. Dec; 31(4):303-11.
36. Proffit WR, Fields HW & Sarver DM. (2000) Contemporary orthodontics, 3rd edn.
Mosby, St Louis, p. 344.
37. Proffit WR, Fields HW & Sarver DM. (2012) Contemporary Orthodontics. 5th ed.
New York:Mosby.
(R)
38. Ricketts, R.M.; Bench, R.W. Gugino, C.F.; Hilgers, J.J.; and Schulhof, R.J. (1979)
Bioprogressive Therapy, Rocky Mountain Orthodontics, Denver.
39. Roth RH. (1981) Functional occlusion for the Orthodontist. Part III. J Clin Orthod.
Mar; 15(3):174-9, 182-98.
40. Roth RH. (1987) the straight-wire appliance 17 years later. J Clin Orthod. Sep;
21(9):632-42.
(S)
41. Saleh M, EI-Mowafy O.(2010) Bond strength of orthodontic brackets with new
self-adhesive resin cements. Am J Orthod Dentofac Orthop 137:528-533.
42. Saxe, A.K.; Louie, L.J.; and Mah, J.(2010): Efficiency and effectiveness of
SureSmile, World J. Orthod. 11:16-22.
39
43. Sernetz F.(1993) Qualität und Normung orthodontischer Produkte aus der Sicht des
Herstellers. Kieferorthopädische Mitteilungen 7: 13-26
44. Sifakakis et al.(2013) Torque expression of 0.018 and 0.022 inch conventional
brackets. Eur J Orthod. Oct;35(5):610-4.
45. Stolzenberg J.(2003)The Russell attachment and its improved advantages. Int J
Orthod Dent Child. 21:837–840* 701-0262 Rev A,.
46. Swartz ML.(2001) Comprehensive fixed appliance therapy. In: McNamara JA,
Brudon WL, eds. Orthodontics and Dentofacial Orthopedics. Ann Arbor,Mich:
Needham Press; 149–151.
(U)
47. Usmani T, O'Brien KD, Worthington HV, et al. 2002) A randomized clinical trial
to compare the effectiveness of canine lacebacks with reference to canine tip. J
Orthod.Dec; 29(4):281-6.
(W)
48. Wahl N.(2005) Orthodontics in 3 millennia. Chapter 1: Antiquity to the mid-19th
century. Am J Orthod Dentofacial Orthop. Feb; 127(2):255-9.
49. Weinberger BW.(2001) Historical résumé of the evolution and growth of
orthodontia. J Am Dent Assoc ,21.
40