Professional Documents
Culture Documents
Data Sheet
Data Sheet
0 0 0 5
0 50
4 0
1 1 2
IP 54
FK SERIES FK-202F TRANSDUCER
TRANSDUCER
SPECIFICATIONS
Page 2 of 2
CONFIGURATION
6H14-042 Rev.9
Issued : Feb. 2015
Revised : Apr. 2019
CV SERIES CV-86 PIEZOELECTRIC VELOCITY TRANSDUCER
TRANSDUCER
SPECIFICATIONS
Model Code
SPECIFICATIONS
Sensitivity 3.94mV/mm/s (100mV/in/s REF.)pk ± 5% at 100Hz, 25°C (77°F REF.)
Max. Velocity 1,270mm/s (50in/s REF.)pk
2
Vibration Limit 2,450m/s (250g REF.)pk
2
24,500m/s (2,500g REF.)pk (non-Intrinsically Safe)
Shock Limit 2
23,520m/s (2,400g REF.)pk (Intrinsically Safe)
Max. Shock Energy 4J (Intrinsically safe)
Linearity ± 1% of F.S.
Natural Frequency 15kHz
Frequency Response 2.5 to 3,500Hz ± 10%, 2 to 7,000Hz ± 3dB
Transverse Sensitivity Max.5%
Output Impedance 200(typical)
Grounding Case isolated, internally shielded
Temperature Response ± 10% (around the operating temperature range)
Power Supply 18 to 30VDC, 2 to 10mADC (constant current)
Operating Temperature Range -50 to +120°C (-58 to +248°F REF.)
Range of Temperature at Explosion proof EX1,7 : -20 to +60C (Transducer, Cable)
construction EX5,8 : -50 to +120C (Transducer, Cable)
Relative Humidity 100%RH
Case Material Stainless Steel
Sealing Hermetic
Protection Rating IP67(CV-861 & CW-□□□F-FF, CV-862)
Weight Approx.145g(CV-861) Approx.250g(CV-862(including cable))
Accessories Supplied M6 mounting stud
Output Connector*4 MIL-C-5015 2-pin
Matching Connector*4 D/MS3106A10SL-4S
CV-861 : Twisted pair shielded cable
Cabling
CV-862 : Coax. cable (intergral cabling type)
2 2
Recommended Cable Shielded Specifications AWG No.20 to No.16 gage (0.5mm to 1.25mm ) Twisted pair shielded cable
*4 CV-861 TYPE SPECIFICATIONS
【NOTICE】
The instructions manual contains important information such as conditions necessary for safe handling of the system.
Such information and conditions are important and indispensable for ensuring safety.
Therefore, be sure to read the instructions manual thoroughly before handling the system.
6H14-062 Rev.5
Issued : Feb. 2015
Revised : Oct. 2019
0 5 0 0
VM-25 VM-25 CONDITION MONITORING SYSTEM
MONITORING SYSTEM
SPECIFICATIONS Page 1 of 5
Model Code
Specification
SPECIFICATIONS Page 2 of 5
Specification
DISPLAY
OUTPUT
※ Selectable by front switch.
Input/output characteristic
Input Points
Input points : 2 channel / slot
Burnout Function*1
*1
Input Transducer When an OK alarm occurs (Output defeat function: ON) or at the monitor
startup, the recorder output and the measurement value are controlled as
Eddy current transducer : FK-202F
follows.
Displacement vibration mesurement
Burnout function setting
Velocity transducer : CV-86, CV-87
Velocity vibration measurement or Burnout
Burnout setting value
displacement vibration measurement Recorder output value Mesurement value
Acceleration transducer : CA-302 Down Scale 0% Equivalent to “0” of the 0
Acceleration vibration measurement or measurement value
velocity vibration measurement Down Scale 0mA / 0V 0V or 0mA 0
Other transducer : Voltage signal
Conversion Accuracy
Vibration Measurement
I/O Conversion Accuracy :±1.5% of F.S. at 100Hz at 25°C
Monitor type*1 : Displacement vibration, Velocity vibration, ±3.0% of F.S. at 100Hz at -20 to +65°C
Acceleration vibration
Monitor range*1 : 1 to 1000 Output
Unit : μm, mils, mm/s, in/s, m/s2, g
Measurement detection : pk-pk、pk、rms Recorder(Non-Isolated) Output*1*4 :
Rectification : Avarage value Current / Voltage output proportional to
Measurement range(AC) : 0 to 9V pk measurement value.
The input voltage of 100% of F.S. at 100Hz should be Measurement value of each channel can be
within the range of 39.4mV pk to 9V pk. assigned to any output channel of its own slot.
Measurement range (DC) : 0 to 22VDC(CV-86, CV-87, CA-302 input) The recorder output gain (1 time or 2 times) can be
: -22 to 0VDC(FK-202F input) changed.
Input voltage range : -24 to 24VDC Number of output points : 2 channel
Input impedance : Approx. 50kΩ Output range : 4 to 20mADC, 1 to 5V
Max. load resistance : 600Ω (current mood)
Output impedance: Approx. 250Ω (voltage mood)
Frequency Response*1 Monitor output : Input signal is output via buffer amplifier.
4 pole high-pass filter : 2Hz, 5Hz, 10Hz, 20Hz (-3db) Location : BNC(Front) and Terminal block(Bottom)
2 pole low-pass filter : 500Hz, 1kHz, 4kHz, 10kHz (-3db) Output impedance : Approx.100Ω
Output voltage : Max.5mA
Transducer Power Supply :
Proximity transducer (FK-202F) : -24VDC±10% / 25mA Max.
Piezoelectric transducer (CA-86, CA-302)
: +24VDC±10% / 4mA (constant current)
SPECIFICATIONS Page 3 of 5
Specification
Power ON
Contact type Energization method Power OFF
Normal state Alarm state
NORMALLY DE-ENERGIZED OPEN OPEN CLOSE
N.O. contact
NORMALLY ENERGIZED OPEN CLOSE OPEN
NORMALLY DE-ENERGIZED CLOSE CLOSE OPEN
N.C. contact
NORMALLY ENERGIZED CLOSE OPEN CLOSE
SPECIFICATIONS Page 4 of 5
Default Value
SPECIFICATIONS Page 5 of 5
Functional Layout
VM-25M00-151-01-01-00-00-00 VM-25M00-151-01-01-26-21-21
1. Vib. measurement 1. Vib. measurement
2. Vib. measurement 2. Vib. measurement
3. Blank 3. Recorder Output
4. Blank 4. Relay Output
5. Blank 5. Relay Output
1 2 3 4 5 1 2 3 4 5
※ The specifications and other items indicated herein are subject to change without notice.
No entry if additional
Model Code / Additional Spec. Code spec, code is not specified.
VM-25S01 /SU0
Setup*1
*1 A PC is required. Setup option includes initial setup of the PC, installation of the software and PC address setting.
Specification
CONNECTION
Supported devices : VM-25 Monitor VM-25 Monitor VM-25S01 Device Config
Number of simultaneous connections : 1device*3
*3 Connected device can be changed by altering the IP address, if the connection is made
via Ethernet. Example of Screen
COMMUNICATION Ethernet
Network : Ethernet 100Base-TX
Protocol : TCP/IP
SCREEN
Screen display language : English
DISPLAY FUNCTION
Actual screens may differ from the images shown in this document
MEASUREMENT VALUES
Gap/Bias Voltage Indications, Digital indication of measurement values,
Peak measurement values
ALARM STATUS
DANGER alarm, ALERT alarm, OK alarm
OTHER DISPLAY
The specifications and other items indicated herein are subject to change without notice.
Time etc. All company and product names in this brochure are trademarks or registered trademarks.