Professional Documents
Culture Documents
Aiwa - BZG 5 - 09 00c 353 3n4
Aiwa - BZG 5 - 09 00c 353 3n4
Aiwa - BZG 5 - 09 00c 353 3n4
This set employs laser. Therefore, be sure to follow carefully the CAUTION
instructions below when servicing. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
WARNING! radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO ATTENTION
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE L'utilisation de commandes, réglages ou procédures autres que
FROM A DISTANCE OF MORE THAN 30cm FROM THE ceux spécifiés peut entraîner une dangereuse exposition aux
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL radiations.
PICK-UP BLOCK.
ADVARSEL!
Caution: Invisible laser radiation when
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
open and interlocks defeated avoid expo-
af funktion. Undgå udsættelse for stråling.
sure to beam.
Advarsel:Usynling laserståling ved åbning,
This Compact Disc player is classified as a CLASS 1 LASER
når sikkerhedsafbrydere er ude af funktion.
product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-
ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit-
CLASS 1 LASER PRODUCT
tävälle näkymättömälle lasersäteilylle. KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
-2-
Precaution to replace Optical block
(KSS-213F, 5ZL-3)
PICK-UP ASSY PWB
Body or clothes electrostatic potential could ruin
(KSS-213F: 87-A90-836-010) MODEL
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
Solder
-3-
How to Adjust the Rotating Phase of the
Gear, Main Cam
1) Push down the hooking catch of the CHAS. MECH, and remove
the TRAY.
2) Align the arrow mark of the Gear, Main Cam with the black round
mark of the CHAS, MECHA as shown below.
3) Confirm that the Slide, Mech Cam is located in the right position,
then insert the TRAY gently.
-4-
ELECTRICAL MAIN PARTS LIST-1/2
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
IC C128 87-A10-504-080 C-CAP,U 0.047-16 K B<EXCEPT ZD3GNDM>
C129 87-010-403-080 CAP, ELECT 3.3-50V
87-A21-821-030 C-IC,LC78645E<EXCEPT ZD3GNDM> C130 87-010-759-020 C-CAP,U 0.1-25 Z F<ZD3GNDM>
87-A21-821-130 C-IC,LC78645NE<ZD3GNDM> C130 87-010-759-080 C-CAP,U, 0.1-25F<EXCEPT ZD3GNDM>
87-A21-822-010 IC,LA6568 C131 87-010-759-020 C-CAP,U 0.1-25 Z F<ZD3GNDM>
-5-
ELECTRICAL MAIN PARTS LIST-2/2
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
PS401 87-A90-156-010 SNSR,SG-240<EXCEPT ZD7NFD> MOTOR C.B(ZD7NFD)
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.
-6-
TRANSISTOR ILLUSTRATION-1/1
B
E ECB
2SC3052 KTA1266
2SA1235 KTC3198
2SA19790
-7-
BLOCK DIAGRAM-1/1
EXCEPT ZD7:3ZG2E3NM
ZD7:3ZG2E7NF
(EXCEPT ZD3GNDM)
(ZD3GNDM)
CD MOUNT SW
TRAY SW
KSS213F(EXCEPT ZD7NFD)
5ZL-3 YR3(ZD7NFD)
CN203
ZD3GNDM MODEL
-8-
WIRING-1/2 (3CD)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
D
5ZL-3
E
-9-
SCHEMATIC DIAGRAM-1/1
(ZD7FD)
(ZD3GNDM)
(ZD7NFD)
(ZD3GNDM,YZD3NCH,YZD3N1CM)
Q301 Q307
2SC3052F 2SA1235
Q301
MC2840
8
Q307
D302
R316
ZD3GNDM MODEL
6
7 MTZJ 6.8B
ZD3GNDM MODEL (ZD3GNDM,YZD3NCM,
(ZD3GNDM,YZD3NCM,YZD3N1CM) YZD3N1CM)
(EXCEPT ZD3GNDM)
(ZD3GNDM) (ZD7NFD)
R316
(ZD7NFD) 180 1/4W
4 5
CD MOUNT SW TRAY SW
OFF UP ON OPEN
ON
OFF DOWN OFF CLOSE
RF-500TB DC-50V
2
1
3
BCH3B14
CN203
CONN,6P 6216H
KSS213F(EXCEPT ZD7)
5ZL-3YR3(ZD7)
(EXCEPT ZD7)
3ZG-2 (ZD7)
-10-
WIRING-2/2 (T-T, DRIVE, MOTOR)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
(CONDUCTOR SIDE) A
CN202 B
H
DRIVE C.B EXCEPT ZD7 MODEL
(CONDUCTOR SIDE) I
M
CN203
O
MOTOR C.B ZD7 MODEL
T
CN203
-11-
WAVE FORM-1/1
8 IC101 ? (XOUT)
8 IC101 ? (XOUT)
TIME/DIV: 5mS
5Vp-p
4.4Vp-p
8
0Vp-p
1.45Vp-p
1.24Vp-p
-12-
IC BLOCK DIAGRAM-1/1
IC, LA6568
-13-
IC DESCRIPTION-1/1 (LC78645)-1/2
-14-
IC DESCRIPTION-1/1 (LC78645)-2/2
-15-
ELECTRICAL MESUREMENT
• Perform the adjustments after the machine enters the test mode.
• Place the CD mechanism horizontally level.
• Equipment and tools required
1. RF Waveform Check
1) Connect an oscilloscope to test point (IC101 4pin, RF), (IC101 11pin, Vref).
1.8 Vp-p
2) Play back the 2nd track of the TCD-782. OSCILLOSCOPE
3) Check to see that the RF waveform has the maximum amplitude 0V
EYE PATTERN
and the center of the wedge waveform has the clear blank. must be CLEAR and MAX.
OUTPUT
VOLT/DIV: 500mV
+ --
TIME/DIV: 0.5µS
2. Jitter Check RF
AC INPUT
VREF
1) While an oscilloscope is kept connected in the same test point
OSCILLOSCOPE
as in the 2. RF Waveform Check, connect the output terminal
of an oscilloscope to the input terminal of a jitter meter. JITTER METER
1) Play back the 4th, 9th and 13th track of ATD-001. Check to see
that noise does not occur and sound skipping does not occur.
-16-
MECHANICAL EXPLODED VIEW-1/1
14
15
16
12
B
19
18
21
20 24
25
22 23
26
*27 YZD3N1CM model
11 is not supplied.
13
29
8
3 31
LED 901
17
7 32
6
10 30
5
CUSH,
CD A
4
3
PWB
PWB
(BZA-1) CUSH,CD A
2
C C
1 CUSH,CD A
3ZG2 28
-17-
MECHANICAL PARTS LIST-1/1
REF. NO PART NO. KANRI DESCRIPTION REF. NO PART NO. KANRI DESCRIPTION
NO. NO.
1 84-ZG1-672-010 F-CABLE,5P 1.25 210MM WHITE N 19 84-ZG1-274-010 GEAR,RELAY 8
2 84-ZG1-225-010 BELT,SQ1.0-63.3 20 81-ZG1-291-110 GEAR,TRAY RELAY NO3
3 84-ZG1-267-010 PULLEY,LOAD MO 8 21 84-ZG1-205-210 GEAR,TRAY (*)
4 87-045-364-010 MOTOR(BCH3B14) 22 83-ZG3-213-010 LVR,SW
5 84-ZG1-238-010 GEAR,WORM N 23 84-ZG1-208-210 LEVER,CAM<ZD7NFD>
-18-
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green
-19-
MECHANISM EXPLODED VIEW 1/2 (3ZG-2)
7
8
-20-
CD MECHANISM PARTS LIST-1/2 (3ZG-2)
-21-
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
921338 Printed in Singapore