Professional Documents
Culture Documents
Moscow React Hanger - Concrete - Mar 8, 2021
Moscow React Hanger - Concrete - Mar 8, 2021
88
www.hilti.com.tr
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + Rebar 12mm
Item number: not available (element) / 2045030 HIT-HY 200-A
(adhesive)
Effective embedment depth: hef,opti = 70.0 mm (hef,limit = 218.0 mm)
Material: B500B
Evaluation Service Report: ESR-3187
Issued I Valid: 1.05.2021 | 1.03.2022
Proof: Design Method ACI 318-11 / Chem
Stand-off installation: eb = 0.0 mm (no stand-off); t = 8.0 mm
Anchor plate :
R lx x ly x t = 250.0 mm x 250.0 mm x 8.0 mm; (Recommended plate thickness: not calculated)
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
3 4
Anchor forces are calculated based on the assumption of a rigid anchor plate.
3 Tension load
Load Nua [kN] Capacity f Nn [kN] Utilization bN = Nua/f Nn Status
Steel Strength* 2.500 40.300 7 OK
Bond Strength** 10.000 35.029 29 OK
Sustained Tension Load Bond Strength* 0.500 7.344 7 OK
Concrete Breakout Failure** 10.000 46.703 22 OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
Variables
2 2
Ase,N [mm ] futa [N/mm ]
113 550.00
Calculations
Nsa [kN]
62.000
Results
Nsa [kN] f steel f Nsa [kN] Nua [kN]
62.000 0.650 40.300 2.500
Nag = (AA ) y
Na
Na0
ec1,Na y ec2,Na y ed,Na y cp,Na Nba ACI 318-11 Eq. (D-19)
f Nag ³ Nua ACI 318-11 Table D.4.1.1
ANa see ACI 318-11, Part D.5.5.1, Fig. RD.5.5.1(b)
2
ANa0 = (2 cNa) ACI 318-11 Eq. (D-20)
t uncr
cNa = 10 da √ 1100
ACI 318-11 Eq. (D-21)
( )
1
'
y ec,Na = eN £ 1.0 ACI 318-11 Eq. (D-23)
1+
cNa
Na
ACI 318-11 Eq. (D-25)
= MAX(
c ) £
c c a,min Na
y cp,Na , 1.0 ACI 318-11 Eq. (D-27)
c ac ac
Nba = l a · t k,c · p · da · hef ACI 318-11 Eq. (D-22)
Variables
t k,c,uncr [N/mm ]
2
da [mm] hef [mm] ca,min [mm] aoverhead 2
t k,c [N/mm ]
11.21 12.0 70.0 910.0 1.000 7.78
Calculations
cNa [mm] ANa [mm ]
2
ANa0 [mm ]
2
y ed,Na
145.2 221,326 84,363 1.000
Results
Nag [kN] f bond f Nag [kN] Nua [kN]
53.891 0.650 35.029 10.000
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
Variables
la aoverhead t k,c [N/mm ]
2
da [mm] hef [mm]
1.000 1.000 7.78 12.0 70.0
Calculations
Nba [kN]
20.542
Results
Nba [kN] f bond 0.55 f Nba [kN] Nua,s [kN]
20.542 0.650 7.344 0.500
Ncbg = (AA ) y
Nc
Nc0
ec,N y ed,N y c,N y cp,N Nb ACI 318-11 Eq. (D-4)
f Ncbg ³ Nua ACI 318-11 Table D.4.1.1
2
ANc0 = 9 hef ACI 318-11 Eq. (D-5)
( )
1
'
y ec,N = 2 eN £ 1.0 ACI 318-11 Eq. (D-8)
1+
3 hef
ef
ACI 318-11 Eq. (D-10)
= MAX(
c ) £
c 1.5h a,min ef
y cp,N , 1.0 ACI 318-11 Eq. (D-12)
c ac ac
1.5
Nb = kc l a √ '
fc hef ACI 318-11 Eq. (D-6)
Variables
hef [mm] ec1,N [mm] ec2,N [mm] ca,min [mm] y c,N
70.0 0.0 0.0 910.0 1.000
'
cac [mm] kc la fc [psi]
111.9 17 1.000 3,626
Calculations
ANc [mm ]
2
ANc0 [mm ]
2
y ec1,N y ec2,N y ed,N y cp,N Nb [kN]
152,100 44,100 1.000 1.000 1.000 1.000 20.833
Results
Ncbg [kN] f concrete f Ncbg [kN] Nua [kN]
71.851 0.650 46.703 10.000
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
4 Shear load
Load Vua [kN] Capacity f Vn [kN] Utilization bV = Vua/f Vn Status
Steel Strength* 1.250 22.500 6 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Bond Strength 5.000 75.448 7 OK
controls)**
Concrete edge failure in direction x+** 5.000 95.345 6 OK
Variables
2 2
Ase,V [mm ] futa [N/mm ]
113 550.00
Calculations
Vsa [kN]
37.500
Results
Vsa [kN] f steel f Vsa [kN] Vua [kN]
37.500 0.600 22.500 1.250
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
Na0
ec1,Na y ec2,Na y ed,Na y cp,Na Nba ] ACI 318-11 Eq. (D-41)
f Vcpg ³ Vua ACI 318-11 Table (D.4.1.1)
ANa see ACI 318-11, Part D.5.5.1, Fig. RD.5.5.1(b)
2
ANa0 = (2 cNa) ACI 318-11 Eq. (D-20)
t uncr
cNa = 10 da √ 1100
ACI 318-11 Eq. (D-21)
( )
1
'
y ec,Na = eN £ 1.0 ACI 318-11 Eq. (D-23)
1+
cNa
na
ACI 318-11 Eq. (D-25)
= MAX(
c ) £
c c a,min Na
y cp,Na , 1.0 ACI 318-11 Eq. (D-27)
c ac ac
Nba = l a · t k,c · p · da · hef ACI 318-11 Eq. (D-22)
Variables
kcp aoverhead t k,c,uncr [N/mm ]
2
da [mm] hef [mm] ca,min [mm]
2
t k,c [N/mm ]
2 1.000 11.21 12.0 70.0 910.0 7.78
Calculations
cNa [mm] ANa [mm ]
2
ANa0 [mm ]
2
y ed,Na
145.2 221,326 84,363 1.000
Results
Vcpg [kN] f concrete f Vcpg [kN] Vua [kN]
107.783 0.700 75.448 5.000
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
Vcbg = (AA ) y
Vc
Vc0
ec,V y ed,V y c,V y h,V y parallel,V Vb ACI 318-11 Eq. (D-31)
f Vcbg ³ Vua ACI 318-11 Table D.4.1.1
AVc see ACI 318-11, Part D.6.2.1, Fig. RD.6.2.1(b)
2
AVc0 = 4.5 ca1 ACI 318-11 Eq. (D-32)
( )
1
'
y ec,V = 2ev £ 1.0 ACI 318-11 Eq. (D-36)
1+
3ca1
a1
ACI 318-11 Eq. (D-38)
= (7 ( ) √ d ) l
0.2
l
Vb e
a a √f'c c1.5
a1 ACI 318-11 Eq. (D-33)
d a
Variables
ca1 [mm] ca2 [mm] ecV [mm] y c,V ha [mm]
910.0 910.0 0.0 1.000 250.0
'
le [mm] la da [mm] fc [psi] y parallel,V
70.0 1.000 12.0 3,626 1.000
Calculations
AVc [mm ]
2
AVc0 [mm ]
2
y ec,V y ed,V y h,V Vb [kN]
613,750 3,726,450 1.000 0.900 2.337 393.245
Results
Vcbg [kN] f concrete f Vcbg [kN] Vua [kN]
136.207 0.700 95.345 5.000
z z
bNV = bN + bV <= 1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Condition A applies where the potential concrete failure surfaces are crossed by supplementary reinforcement proportioned to tie the
potential concrete failure prism into the structural member. Condition B applies where such supplementary reinforcement is not provided, or
where pullout or pryout strength governs.
• Design Strengths of adhesive anchor systems are influenced by the cleaning method. Refer to the INSTRUCTIONS FOR USE given in the
Evaluation Service Report for cleaning and installation instructions.
• For additional information about ACI 318 strength design provisions, please go to
https://submittals.us.hilti.com/PROFISAnchorDesignGuide/
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. Reference ACI 318-11,
Part D.9.1
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
7 Installation data
Anchor type and diameter: HIT-HY 200 + Rebar 12mm
Profile: IPE, IPE 100; (L x W x T x FT) = 100.0 mm x 55.0 mm x 4.1 mm x 5.7 Item number: not available (element) / 2045030 HIT-HY
mm 200-A (adhesive)
Hole diameter in the fixture: df = 12.0 mm Maximum installation torque: -
Plate thickness (input): 8.0 mm Hole diameter in the base material: 16.0 mm
Recommended plate thickness: not calculated Hole depth in the base material: 70.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 102.0 mm
Cleaning: Compressed air cleaning of the drilled hole according to instructions
for use is required
Rebar with HIT-HY 200 injection mortar with 70 mm embedment h_ef, 12mm, Hammer drilled installation per ESR-3187
y
125.0 125.0
35.0
3 4
125.0
180.0
x
125.0
1 2
35.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.88
www.hilti.com.tr
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Mar 8, 2021 (1) Date: 11.09.2023
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2023 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10