Professional Documents
Culture Documents
Diamant 16 en
Diamant 16 en
DIAMANT 16
Diamant 16 The demands placed on modern semi-
mounted reversible ploughs are be-
headlands and maximum acreage
performance.
2
outputs on tractors and larger work- The DuraMaxx generation of plough The traction booster reduces slip and
ing widths. bodies delivers a longer service life, increases the load applying to the rear
less clogging and lower traction re- tractor axle, reducing fuel consump-
Their design allows operators to quirements, resulting in cost savings tion.
plough right up to fences, ditches and when using the plough.
field edges, despite large working The ploughs can be transported safely
widths. The skimmers can be easily The Hydromatic-T overload protection on roads, even at high speeds, with-
and quickly adjusted without tools. allows plough bodies to be deflected out placing excessive loads on trac-
in three directions. tors.
Equipped with Dural plough bodies in
the basic equipment. The OptiLine adjustment system
allows fuel savings of up to 10%.
3
Diamant 16 – On-land or in the furrow...
In recent years, there has been a trend
towards larger tractors with wider
tyres with 710 mm, 800 mm or above.
As a result there is not enough space
for these large tyres in the furrows, re-
sulting in soil compaction damage
when driving across loosened soils
and along furrow edges.
quickly and easily converted to in-fur- can be swivelled into two positions.
30
0,6
1,2
40
0,4
1,0
60
[bar] 0,6
70
80
0,2
90
On-land ploughing with the Diamant mant 16, the swivel cylinder is ex-
[bar]
100
(cm)
4
... with maximum traction
Diamant 16 ploughs can be fitted with traction booster is automatically re- The height of the horizontal draw
an optional traction booster. duced to ensure that full tractor sta- point is easily adjusted simply by re-
bility is maintained at all times. As positioning a pin.
• An additional hydraulic cylinder soon as the transport wheel is low-
transfers weight to the tractor’s rear ered, pressure is automatically in- • This allows a precise load transfer to
axle to boost its traction. creased again. the rear axle of the tractor.
• This “smart ballasting” system re- • When using crawler tracks, the draw
duces slip and therefore saves fuel. point is set very low to ensure that
even loads are applied to the tracks.
• As soon as the hydraulic system
raises the plough frame via the • Slip is minimised on all tractors
transport wheel, the pressure in the through the optimal transfer of trac-
tive forces.
5
OptiLine adjustment system
The draw point of the Diamant lies in
front of the lower link connection. This
position far to the front ensures an ef- 1
6
Always the right bearing
7
4 2
5 1
3
6
Plough frame
Fixed main
bearing pin
Lubricating
point
The fixed bolted connection between The frame plates supporting the The main bearing bolt of the swivel
the adjustment brackets and frame swivel brackets are bolted to the bracket is equipped with tension
provides outstanding stability, reliable frame. This provides outstanding sta- bushes and locked against rotation
durability and a high degree of engi- bility, increased durability and a high with the frame plates.
neering precision. degree of engineering precision.
• The swivel bracket has crimped
• Once the central bolt has been loos- • The pivots for the swivel brackets, flange bushings. The two bushes of
ened, four working widths which are supported next to the the cutting width adjustment run
between 33 and 60 cm can be set frame, are located close to the within each other for a long service
(depending on interbody clearance). plough body. This reduces strain on life.
the bearings and other components.
• Skimmers and disc coulters are ad- • Each component can be replaced
justed automatically. • The working width is continuously separately if worn.
adjustable via a double-acting
hydraulic cylinder.
7
Mounting, parking and rotation
The continuous, flexible Cat. 3 and 4 Two reversing cylinders ensure that The stand height can be adjusted to
cross shaft absorbs major impact the plough can be rotated powerfully various levels to ensure that the head-
loads to protect both the tractor and and smoothly by 180 degrees. stock is ideally positioned for coupling
headstock. to and decoupling from the tractor.
• Single-acting reversing mechanism
• It can be rotated towards the rear to via a telescopic cylinder with • The stand is easily moved from the
reduce side pull (in the version with- mechanical tilt adjustment. parking to the transport or working
out OptiLine). position by simply repositioning a
pin.
• The plough axle is surface hard-
ened, mounted on tapered rollers
and easy to lubricate for high
strength and a long service life.
8
Tilt adjustment Straightforward Front furrow adjustment
uncoupling
The tilt adjustment is made via screws The plough can be positioned verti- The front furrow width is set via a
either side of the central framework. cally before uncoupling by removing turnbuckle. There is an option to make
the relevant tilt adjustment screw. this adjustment hydraulically from the
• The tilt adjustment is made sepa- tractor cab.
rately for each side by a simple me- • This straightens the headstock to
chanical device. make coupling and uncoupling • With on-land ploughing, this setting
processes easier. adjusts the distance between the
• The screw serves as a stop for the tractor and the furrow.
reversing cylinder.
Turning procedure
The large clearance between the controlled during plough rotation. The on narrow headlands and in hilly or
plough headstock and tractor permits optimal interaction between the re- difficult terrain.
a steering angle of up to 90°. The versing mechanism and transport
transport wheel is automatically wheel allows easy, rapid turning even
9
Quality and safety on fields and roads
Road transport
The semi-mounted reversible plough • It can then be safely towed behind • The ModuLight LED provides maxi-
mum safety during road transport.
is rotated into its centre position and the tractor just like any single-axle
locked via two stop valves for quick trailer.
and safe road transport.
• All Diamant ploughs feature a trans-
port wheel damper as standard to
protect both tractor and plough
effectively against excessive loads.
The large transport wheel minimises hydraulic/electrical mechanism. The • The hydro-pneumatic suspension
soil compaction during ploughing and relevant shut-off valve is set to ei- absorbs major impact loads.
ensures the required safety for road ther the SET or WORK position. This
transport. can be done manually or via a spool • A range of wheel sizes is available
valve operated from the tractor seat. upon request:
• The Diamant 16 features hydraulic Standard equipment
depth adjustment. The working • An easy-to-read display facilitates 400/55-22.5, 1,020 x 400 mm
depth is set via the three-point link- working depth adjustments and at Optional
age at the front and via the trans- the same time protects the lifting 500/45-22.5, 1,020 x 500 mm
port wheel at the rear, either via a cylinder against dirt. 500/60-22.5, 1,200 x 500 mm
hydraulic/mechanical (standard
equipment) or optionally via a
10
Cost-effective plough bodies
Sword coulter
Landside
Dural mouldboard
Share wing
The frog of the Dural body is tem-
Share point pered and extremely strong.
Hard faced share point
Mouldboard
• The pitch of the plough bodies is
Mouldboard shin adjustable to ensure consistently
good penetration of the plough into
the soil.
The slats of the slatted bodies are • Slatted bodies and conventional • High material density and firm at-
made of thick, fully hardened special mouldboards are based on the same tachment provide for resistance to
steel and can be individually replaced. basic body. wear and breakage.
• The attachment screws are deeply • The shares are divided and made of • The wear zones of the share wings
sunk to ensure that the slats remain micro-alloyed boron steel. are significantly larger than with
firmly in place throughout their conventional shares.
extremely long service life. • The overlapping design prevents
roots or foreign objects from catch-
ing.
11
Reliable and cost-effective on all soils
3800
Dural: 0 279 (Gewichtabnahme
(Weight reductioninin[g])
[g])
3600
DuraMaxx: 0 158 (Gewichtabnahme
(Weight reductioninin[g])
[g])
3400
3200
Weight [g]
3000
Gewicht
2800
2600
2400
2200
2000
0 85 210 320
CultivatedFläche
bearbeitete area [ha]
[ha]
Prof. Dr. YvesProf.
Reckleben,
Dr. YvesKiel University
Reckleben, of Applied Sciences
Fachhochschule Kiel
The DuraMaxx plough body rep- than previous bodies. This was pos- • Mouldboards and slats are fully sup-
resents a radically new approach that sible as the material is no longer ported by the frog. They are no lon-
increases service life by up to 150% weakened by drilled or punched ger a load-bearing part of the
whilst reducing set-up times by up to holes. plough body. With these bodies, al-
80%. most the full part length is available
• DuraMaxx plough bodies offer a for use, as there are no worn screw
• All DuraMaxx components are man- longer service life, less clogging and heads requiring slats or mould-
ufactured from much harder steel low traction requirements. boards to be replaced early.
12
Quick, tool-less change Body assembly DuraMaxx Hybrid
for sticky soils
DuraMaxx plough bodies are de- The DuraMaxx plough body is avail- The DuraMaxx plough body can also
signed to allow mouldboards, slats able with mouldboards or slats. be configured with plastic slats. These
and mouldboard shins to be changed are ideal for use on extremely sticky
quickly and without requiring tools. • The mouldboard and slats are at- soils and in soil conditions where only
tached with no more than two little pressure applies on the mould-
• The mouldboard shin, which can be hooks. board.
easily detached after removing a
lynch pin, also serves to keep the • On the slat bodies, the clearance be- • Optimal sliding properties are
other components securely locked tween the slats and their support achieved by using plastic slats at the
in place. The mouldboard or slats has been considerably increased. top and bottom areas of the plough
can then be simply pulled out of The support is aligned with the slats, body, which are most susceptible to
their connectors. which allows the plough to work adhesion.
without blockages even in difficult
• The share point is attached with conditions. • This ensures that the DuraMaxx
only a single screw, making a body works without any adhesion
change much quicker than with con- even in extreme conditions.
ventional systems.
13
Disruption-free ploughing in any conditions
All LEMKEN overload protection sys- • The Diamant T version features the Minimum and maximum trigger force
tems protect against damage from the Hydromatic overload protection. values can be individually set between
share point impacting on obstacles. The trigger force is set via a stop- 120 and 200 bar via the hand wheel on
cock below the pressure gauge. The the (optional) control valve, e.g. for
• The Diamant features double-cut trigger force should be set as low as shallow sections or sections with
shear-off protection with a shear- possible to protect the tractor and heavy soils.
bolt as standard. In ploughs with plough.
automatic overload protection, the • These limits can then be actuated
shear bolt protects the plough via the control unit on the tractor.
against damage due to the system
becoming trapped under rocks or • No readjustments based on pres-
roots. sure gauge readings are necessary.
14
• The plough bodies are kept stable at
all times and cannot unlatch or tear
off.
The innovative LEMKEN Hydromatic • The high trigger and re-entry forces
overload protection comprises a steer- of the Hydromatic ensure that the
ing system that maintains a firm con- system is triggered softly and
nection between the plough body smoothly when an obstacle is en-
and bearing point in any position. countered.
15
Always well prepared
The working depth can be continu- The Diamant version with skimmers The trash boards are mounted directly
ously adjusted via a pin on the flat features robust flat stalks that are con- on the leg and can be set over a wide
stalk. This requires no tools. nected to the frame via two bolts. range.
This allows all skimmers on the plough • The flat stalk prevents skimmer • They ensure blockage-free work and
to be adjusted evenly without distortion. the neat insertion of plant material.
repeated checks and readjustments.
• It can be easily removed for plough- • Trash boards are also available in
ing without skimmers. plastic for sticky soil conditions.
New skimmers with different share • The special share shape minimises • Plastic mouldboards are available
lengths reliably prevent blockages wear and increases service life while for sticky soils and in soil conditions
during ploughing even in difficult creating excellent soil flow. where only little pressure applies on
conditions. the skimmer.
• The specially shaped mouldboard
separates and neatly deposits the
organic matter.
16
1 2
3 4 5
Subsoiler for
Disc coulter
effective loosening
The smooth disc coulter is corrugated • The disc coulters are available in a The specially shaped subsoiler delivers
at the sides to provide continuous range of versions and mounting a particularly good loosening effect.
drive even when breaking up large positions:
amounts of organic material. 1) 0 500 mm, next to skimmers • The subsoiler depth can be adjusted
2) 0 590 mm, in front of/next to without tools, and the subsoiler can
• The disc coulter arms are swivelled skimmers, adjustable also simply be removed without
vertically for depth adjustment and 3) 0 500 mm, suspended requiring tools, if necessary.
can be fixed in position with a screw 4) 0 590 mm, next to skimmers
when engaged with the gears. 5) Alternatively, serrated discs are • All wear parts can be individually
available in all diameters. replaced. The stalk guard prevents
• The smooth bearings on the un- wear on the stalk.
ploughed side are double-sealed
against dirt ingress.
17
Technical data
Description Working width per furrow Interbody clearance Number of furrows Weight
[approx. cm] [cm] [approx. kg]
Diamant Diamant V Diamant Diamant V
With double-cutting shear bolt device
Diamant 16 (V) 5 L 100 33, 38, 44, 50 30 - 55 100 5 2,584 2,759
Diamant 16 (V) 5+1 L 100 33, 38, 44, 50 30 - 55 100 5+1 2,834 3,069
Diamant 16 (V) 6 L 100 33, 38, 44, 50 30 - 55 100 6 2,830 3,040
Diamant 16 (V) 6+1 L 100 33, 38, 44, 50 30 - 55 100 6+1 3,080 3,350
Diamant 16 (V) 7 L 100 33, 38, 44, 50 30 - 55 100 7 3,076 3,321
Diamant 16 (V) 7+1 L 100 33, 38, 44, 50 30 - 55 100 7+1 3,326 3,631
Diamant 16 (V) 8 L 100 33, 38, 44, 50 30 - 55 100 8 3,322 3,602
Diamant 16 (V) 8+1 L 100 33, 38, 44, 50 30 - 55 100 8+1 3,572 3,912
Diamant 16 (V) 5 L 120 40, 45, 53, 60 30 - 60 120 5 2,634 2,829
Diamant 16 (V) 5+1 L 120 40, 45, 53, 60 30 - 60 120 5+1 2,896 3,153
Diamant 16 (V) 6 L 120 40, 45, 53, 60 30 - 60 120 6 2,892 3,124
Diamant 16 (V) 6+1 L 120 40, 45, 53, 60 30 - 60 120 6+1 3,154 3,448
Diamant 16 7 L 120 40, 45, 53, 60 120 7 3,150
Diamant 16 7+1 L 120 40, 45, 53, 60 120 7+1 3,412
18
Service is decisive
The renowned, almost legendary In the unlikely event that a part is not in contract farmers and dealers in com-
LEMKEN service begins right after the stock, it can be ordered from the missioning implements and for expert
purchase of a LEMKEN implement. LEMKEN logistics centre, which is open maintenance and repair. Thanks to reg-
We operate 18 branches and external around the clock, 365 days a year, and ular training, LEMKEN customer service
warehouses in Germany and have our delivered to the customer within is always up-to-date with current
own sales companies and importers in 24 hours. LEMKEN technology.
more than 40 countries worldwide to
Expertise from LEMKEN spe-
ensure optimum availability of imple-
cialists
ments and spare parts in cooperation
with specialist agricultural machinery Highly qualified customer service tech-
dealers. nicians are available to assist farmers,
19
lemken.com
Weseler Strasse 5
info@lemken.com
Phone +49 2802 81-0
46519 Alpen, Germany
LEMKEN GmbH & Co. KG Your specialist LEMKEN dealer:
LEMKEN . 12/19 . 17512637/en All data, dimensions and weights are subject to ongoing further technical development and are therefore not binding.
Weights given are always based on standard features. All information given is subject to change without notice.