Professional Documents
Culture Documents
19C002-KA-55-L-SA-00001 Piping and Valve Specification Rev 01
19C002-KA-55-L-SA-00001 Piping and Valve Specification Rev 01
Originator/Contractor: Client/Contractor:
Originator Doc. no: Orig. Rev: Company Doc. no: Comp. Rev:
19C002-KA-55-L-SA-00001 01 18002-KAN-055-L-SA-0001
Sub-Supplier: Main Tag / Equipment:
HRSG
55-WHR-0101/0201/0301/0401
Sub-Supplier Doc. no: Contract/PO no: Total Pages:
67.6130 18
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
Summary of Changes
Rev. Description:
01 First Issue
Holds
Hold no. Page Description:
01 All All Valve Data Sheets (VDS’s)
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 2 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
Contents
1 Introduction ................................................................................................................. 4
1.1 Objective .......................................................................................................................... 4
2 Definitions and Abbreviations ...................................................................................... 4
2.1 Definitions ........................................................................................................................ 4
2.2 Abbreviations useful for piping and valve disciplines ...................................................... 4
3 Regulations, Codes and Standards................................................................................ 5
3.1 Classification..................................................................................................................... 5
3.2 Design Codes and Standards ............................................................................................ 5
3.2.1 DNVGL Normative references ....................................................................................... 5
3.2.2 API - American Petroleum Institute ............................................................................... 6
3.2.3 ASME/ASTM - American Society of Mechanical Engineers ........................................... 6
3.2.4 EU – European Standards .............................................................................................. 7
3.2.5 ISO – International Organization for Standardization ................................................... 7
3.2.6 NORSOK Design Guidelines ........................................................................................... 7
3.2.7 Other standards ............................................................................................................. 7
4 Piping Classes (PCS) Valid for This Project..................................................................... 8
4.1 PCS AC21 .......................................................................................................................... 8
4.2 PCS DC21 .......................................................................................................................... 9
4.3 PCS DC11 ........................................................................................................................ 10
4.4 PCS P11-class 600 ........................................................................................................... 11
4.5 PCS P11 – class 1500 ...................................................................................................... 12
4.6 PCS P22 – Class 900 ........................................................................................................ 13
4.7 PCS DC21 - Vacuum ........................................................................................................ 14
5 Valve Data Sheets (VDS)............................................................................................. 15
6 VDS Annex A .............................................................................................................. 15
6.1 Valve Internals ................................................................................................................ 15
6.2 Valve Testing .................................................................................................................. 15
6.3 Hand Wheels, Wrenches and Gear Boxes ...................................................................... 15
6.4 General ........................................................................................................................... 16
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 3 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
1 Introduction
1.1 Objective
This document contains the Piping and Valve Specification to be used for the GOLAR GIMI FLNG – HRSG
Modules project.
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 4 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
3.1 Classification
The project has chosen to invoke selected certification activities for the process unit with the class
notation, PROD, under the supervision of DNV GL AS, the project’s classification society. This process
requires DNV GL to execute a design review, manufacturer quality control, and manufacturing
procedures review according to DNVGL-OS-E201, January 2017, amended July 2017.
The SUPPLIER is responsible for ensuring that the total scope of work is fully in accordance with the
design, construction, inspection, testing and certification requirements of the CLASSIFICATION
SOCIETY.
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 5 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
DNVGL-RU-SHIP- DNVGL Rules for ships Pt.1 Ch.3 Jan 2017, Amended Jul
Pt1 Ch3 – General regulations – 2017
Documentation and certification requirements,
general (Replacing
DNV-RP-A201 Plan Approval
Documentation Types)
DNVGL-RU-SHIP- DNVGL Rules for ships Pt.3 Ch.12 – Open and Jul 2017, into force Jan
Pt3 Ch12 closing appliances 2018
DNVGL-RU-SHIP- DNVGL Rules for ships Pt.4 Ch.6 – Piping systems Jul 2017, into force Jan
Pt4 Ch6 2018
DNVGL-RU-SHIP- DNVGL Rules for ships Pt.4 Ch.8 – Electrical Jan 2017, Amended Jul
Pt4 Ch8 Installations 2017
DNVGL-RU-SHIP- DNVGL Rules for ships Pt.5 Ch.7 – Liquefied gas Jul 2017, into force Jan
Pt5 Ch7 tankers 2018
DNVGL-RP-C203 Fatigue Design of Offshore Steel Structures April 2016
DNVGL-RP-C204 Design Against Accidental Loads August 2017
DNVGL-RP-C205 Environmental Conditions and Environmental August 2017
Loads
DNVGL-RP-D101 Structural Analysis of Piping July 2017
Systems
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 6 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ASME BPVC-VIII-2 : Boiler and Pressure Vessel Code, Section VIII: Rules for Construction of
Pressure Vessels, Division 2
ASME BPVC-IX : Boiler and Pressure Vessel Code, Section IX: Welding, Brazing and Fusing
Qualifications
ASME PTC 19.3 TW : Temperature Measurement Instruments and Apparatus - Thermowells
ASTM A380/A380M : Cleaning and De-scaling of Stainless Steel Parts
ASTM A-751 : Standard Test Methods, Practices, and Terminology for Chemical Analysis of
Steel Products
ASTM A780 : Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip
Galvanized Coatings
ASTM E165/E165M : Standard Practice for Liquid Penetrant Examination for General Industry
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 7 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00 10.00
OD (mm) 21.3 26.7 33.4 48.3 60.3 88.9 114.3 168.3 219.1 273.1
THK (mm) 3,75 3,95 4,6 3,4 3,95 5,5 6,1 7,15 6,4 6.35
SCH 80 80 80 40 40 40 40 40 20 20
SCH XS XS STD STD STD
Weld Factor 1 1 1 1 1 1 1 1 0,95 0,95
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 8 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00 10.00
OD (mm) 21,3 26.7 33.4 48.3 60.3 88.9 114.3 168,3 219,1 273,1
THK (mm) 3,73 3,91 4,55 5,08 5,54 7,62 8,56 10,97 12,7 15,09
SCH 80 80 80 80 80 80 80 80 80 80
SCH
Weld Factor 1 1 1 1 1 1 1 1 1 1
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 9 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00 10.00
OD (mm) 21,3 26.7 33.4 48.3 60.3 88.9 114.3 168,3 219,1 273,1
THK (mm) 3,73 3,91 4,55 5,08 5,54 7,62 8,56 10,97 12,7 15,09
SCH 80 80 80 80 80 80 80 80 80 80
SCH
Weld Factor 1 1 1 1 1 1 1 1 1 1
END
SIZE GEOMETRIC MATERIAL
TYPE EDS CONN MDS RATING SCHD NOTES
FROM/TO STANDARD DESCRIPTION
#1 #2
PIPE 0.50 10.00 ASME B36.10M PE PE A333 6 SMLS
PIPE NIPPLE 100MM LONG 0.50 1.00 ASME B36.10M TE PE A333 6 SMLS
CAP 0.50 10.00 ASME B16.9 BE A420 WPL6
ECC/CONC. REDUCER 0.50 10.00 ASME B16.9 BE BE A420 WPL6
ELBOW LONG RADIUS 45/90
0.50 10.00 ASME B16.9 BE BE A420 WPL6
DEG
EQUAL/RED. TEE 0.50 10.00 ASME B16.9 BE BE A420 WPL6
WELDOLET 0.50 8.00 MSS-SP-97 BE BE A350 LF2
REINFORCED NIPOFLANGE 2.00 10.00 MANUF. STANDARD NOL1 BE RJ A350 LF2 003
BLIND FLANGE 1.00 10.00 ASME B16.5 RJ A350 LF2/A516 Gr70
WELDNECK FLANGE 0.50 10.00 ASME B16.5 RJ BE A350 LF2
080,
WELDNECK FLANGE 0.50 14.00 ASME B16.5 RF BE A350 LF2
081
WELDNECK ORIFICE FLANGE 1.00 10.00 ASME B16.36 RJ BE A350 LF2
SPECTACLE BLIND 0.50 10.00 AME B16.48 RJ RJ A516 Gr70
SPECTACLE BLIND 0.50 14.00 ASME B16.48 RF RF A516 Gr.70 080
GASKET OVAL RING 0.50 10.00 ASME B16.20 SOFT IRON
GASKET 0.50 14.00 ASME B16.20 RF RF SPIRAL WOUND SS316 080
STUD BOLT C/W NUTS 0.50 10.0 ASME B16.5 A193 B7 / A194 2H
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 10 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00 10.00 12.00 14.00 16.00
OD (mm) 21,3 26.7 33.4 48.3 60.3 88.9 114.3 168,3 219,1 273,1 328,8 355,6 406,4
THK (mm) 2,77 2,87 2,77 3,18 3,91 4,78 6,02 7,11 8,18 12,7 12,7 12,7 16,66
SCH STD STD 10 30 STD 30 STD STD STD XS XS XS 60
SCH
Weld Factor 1 1 1 1 1 1 1 1 1 1
END CONN
TYPE SIZE FROM/TO GEOMETRIC STANDARD EDS MATERIAL DESCRIPTION MDS RATING SCHD NOTES
#1 #2
PIPE 0.50 10.00 ASME B36.10M PE PE ASTM A-335 Gr.P11
PIPE NIPPLE 100MM LONG 0.50 1.00 ASME B36.10M TE PE ASTM A-335 Gr.P11
CAP 0.50 10.00 ASME B16.9 BE ASTM A-335 Gr.P11
ECC/CONC. REDUCER 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P11
ELBOW LONG RADIUS 45/90 DEG 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P11
EQUAL/RED. TEE 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P11
WELDOLET 0.50 8.00 MSS-SP-97 BE BE ASTM A-335 Gr.P11
REINFORCED NIPOFLANGE 2.00 10.00 MANUF. STANDARD NOL1 BE RJ ASTM A182 F11
BLIND FLANGE 1.00 10.00 ASME B16.5 RJ ASTM A182 F11
WELDNECK FLANGE 0.50 10.00 ASME B16.5 RJ BE ASTM A182 F11
WELDNECK FLANGE 0.50 14.00 ASME B16.5 RF BE ASTM A182 F11
WELDNECK ORIFICE FLANGE 1.00 10.00 ASME B16.36 RJ BE ASTM A182 F11
SPECTACLE BLIND 0.50 10.00 AME B16.48 RJ RJ ASTM A182 F11
SPECTACLE BLIND 0.50 14.00 ASME B16.48 RF RF ASTM A182 F11
GASKET OVAL RING 0.50 10.00 ASME B16.20 SOFT IRON
GASKET 0.50 14.00 ASME B16.20 RF RF SPIRAL WOUND SS316
STUD BOLT C/W NUTS 0.50 10.0 ASME B16.5 A193 B7 / A194 2H
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
Note 2:
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 11 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00 10.00 12.00
OD (mm) 21,3 26.7 33.4 48.3 60.3 88.9 114.3 168,3 219,1 273,1 328,8
THK (mm) 3,73 3,91 4,55 5,08 8,74 11,13 11,13 14,27 18,26 21,44 25,4
SCH XS XS XS XS 160 160 120 120 120 120 XXS
SCH
Weld Factor 1 1 1 1 1 1 1 1 1 1
END CONN
TYPE SIZE FROM/TO GEOMETRIC STANDARD EDS MATERIAL DESCRIPTION MDS RATING SCHD NOTES
#1 #2
PIPE 0.50 10.00 ASME B36.10M PE PE ASTM A-335 Gr.P11
PIPE NIPPLE 100MM LONG 0.50 1.00 ASME B36.10M TE PE ASTM A-335 Gr.P11
CAP 0.50 10.00 ASME B16.9 BE ASTM A-335 Gr.P11
ECC/CONC. REDUCER 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P11
ELBOW LONG RADIUS 45/90 DEG 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P11
EQUAL/RED. TEE 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P11
WELDOLET 0.50 8.00 MSS-SP-97 BE BE ASTM A-335 Gr.P11
REINFORCED NIPOFLANGE 2.00 10.00 MANUF. STANDARD NOL1 BE RJ ASTM A182 F11
BLIND FLANGE 1.00 10.00 ASME B16.5 RJ ASTM A182 F11
WELDNECK FLANGE 0.50 10.00 ASME B16.5 RJ BE ASTM A182 F11
WELDNECK FLANGE 0.50 14.00 ASME B16.5 RF BE ASTM A182 F11
WELDNECK ORIFICE FLANGE 1.00 10.00 ASME B16.36 RJ BE ASTM A182 F11
SPECTACLE BLIND 0.50 10.00 AME B16.48 RJ RJ ASTM A182 F11
SPECTACLE BLIND 0.50 14.00 ASME B16.48 RF RF ASTM A182 F11
GASKET OVAL RING 0.50 10.00 ASME B16.20 SOFT IRON
GASKET 0.50 14.00 ASME B16.20 RF RF SPIRAL WOUND SS316
STUD BOLT C/W NUTS 0.50 10.0 ASME B16.5 A193 B7 / A194 2H
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
Note 2:
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 12 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00 10.00 12.00
OD (mm) 21,3 26.7 33.4 48.3 60.3 88.9 114.3 168,3 219,1 273,1 328,8
THK (mm) 3,73 3,91 4,55 5,08 5,54 7,62 8,56 10,97 15,09 18,26 21,44
SCH XS XS XS XS XS XS XS XS 100 100 100
SCH
Weld Factor 1 1 1 1 1 1 1 1 1 1
END CONN
TYPE SIZE FROM/TO GEOMETRIC STANDARD EDS MATERIAL DESCRIPTION MDS RATING SCHD NOTES
#1 #2
PIPE 0.50 10.00 ASME B36.10M PE PE ASTM A-335 Gr.P22
PIPE NIPPLE 100MM LONG 0.50 1.00 ASME B36.10M TE PE ASTM A-335 Gr.P22
CAP 0.50 10.00 ASME B16.9 BE ASTM A-335 Gr.P22
ECC/CONC. REDUCER 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P22
ELBOW LONG RADIUS 45/90 DEG 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P22
EQUAL/RED. TEE 0.50 10.00 ASME B16.9 BE BE ASTM A-335 Gr.P22
WELDOLET 0.50 8.00 MSS-SP-97 BE BE ASTM A-335 Gr.P22
REINFORCED NIPOFLANGE 2.00 10.00 MANUF. STANDARD NOL1 BE RJ ASTM A182 F22
BLIND FLANGE 1.00 10.00 ASME B16.5 RJ ASTM A182 F22
WELDNECK FLANGE 0.50 10.00 ASME B16.5 RJ BE ASTM A182 F22
WELDNECK FLANGE 0.50 14.00 ASME B16.5 RF BE ASTM A182 F22
WELDNECK ORIFICE FLANGE 1.00 10.00 ASME B16.36 RJ BE ASTM A182 F22
SPECTACLE BLIND 0.50 10.00 AME B16.48 RJ RJ ASTM A182 F22
SPECTACLE BLIND 0.50 14.00 ASME B16.48 RF RF ASTM A182 F22
GASKET OVAL RING 0.50 10.00 ASME B16.20 SOFT IRON
GASKET 0.50 14.00 ASME B16.20 RF RF SPIRAL WOUND SS316
STUD BOLT C/W NUTS 0.50 10.0 ASME B16.5 A193 B7 / A194 2H
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
Note 2:
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 13 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
ND (inch) 0.50 0.75 1.00 1.50 2.00 3.00 4.00 6.00 8.00
OD (mm) 21,3 26.7 33.4 48.3 60.3 88.9 114.3 168,3 219,1
THK (mm) 2,41 2,87 2,77 3,18 3,91 7,78 4,79 7,11 7,04
SCH
Weld Factor 1 1 1 1 1 1 1 1 1
Note 1:
Under tolerance abbreviations typical used in above table: 12.5 = 12.5%, The specified under tolerance and weld factor in this table, summaries only
the minimum requirements for the piping items used in this piping class. As stricter requirement may apply for an individual piping item, this
information shall be used for design only and not as part of the purchase specification
Note 2:
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 14 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
6 VDS Annex A
• Valve internals shall be made from a forging, seamless pipe, plate, or bar material according
to an ASTM standard. Equivalent recognized standard may be used but corresponding ASTM
standard and grade to be identified. Materials shall meet the requirements of NACE
MR0175/ISO 15156.
• Min 13% Cr and 4% Ni
• Weld repair is not acceptable.
• A certificate in accordance with ISO 10474/EN 10204 Type 2.2 shall be issued.
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 15 of 16
Doc. title: Piping and Valve Specification
Doc. no.: 18002-KAN-055-L-SA-0001 Rev: 01
Project: Golar Gimi FLNG – HRSG Modules Date: 01.07.2019
• Drive to be suitable for any stem orientation of operation, horizontal to vertical up.
• Lever and handwheel shall be secured by a nut or dowel pin and an additional locking to
provide robust double retention.
• Unless otherwise agreed, wrench or handwheel for valves made from corrosion resistant alloy
shall be in AISI 316 stainless steel material.
• Wrench and hand-wheel shall be made from solid material, suitable for the environmental
conditions. Hollow components shall not be allowed except for gear hand wheels.
• Hand-wheel diameter shall not exceed twice the face-to-face or 32 in (800 mm).
• Wrench length shall not exceed twice the face-to-face or 24 in (600 mm).
• If the force or dimensional limitations are exceeded, the valve shall be provided with a
gearbox.
6.4 General
• The Supplier shall supply a valve maintenance instruction manual. This shall include required
pre-tension (or torques) for bolting in the valve bonnet and body flanges (closures).
• Through conduit gate valves:
• Valves shall be suitable for installation in any position. (except for stem below horizontal).
• Bonnet shall be equipped with a grease fitting for lubrication to stem packing area. Grease
fittings shall either be of one-piece double ball type or two-piece double ball with block.
This document is strictly confidential and contains references and descriptions of intellectual property protected by both local KANFA AS
and international regulations. Any reproduction, use or disclosure is strictly prohibited without explicit permission. Page 16 of 16