Professional Documents
Culture Documents
Citizen Blue Angels Skyhawk C650
Citizen Blue Angels Skyhawk C650
• This watch is solar-powered. Expose the dial to light and use it sufficiently charged.
• To see details of charging time, specifications and operations, refer to the instruction manual: C650/C651/C652 instruction manual
Component identification 5. Press and release the upper right button B repeatedly to
change the target to be set.
UTC hour hand/ UTC minute • Each time you press button B, the target changes as follows:
60
55
70 hand
Hour hand 50 55
NAUT.
70
50 ST
AT 8 Summer time Second Minute Hour 12/24-hour basis
4
5
4
5
.
8
0
0
Button B
90
40
90
40
Minute hand
24-hour hand
10
10
35
35
Crown
11
11
Area name display
• The summer time setting does not appear when selecting “UTC”.
12
30
12
30
. 13
indication
1
4
15
4
5 24
2 23 16 15
• Minute/hour: rotate the crown. When you rotate the crown quickly, the
24 22 17
21 18
23 20 19 16
Second hand
22
indication will change continuously. To stop the rapid change, rotate the
17
21 18
20 19
1/4
C650/C651/C652 Abbreviated instruction
Using the world time Switching the time of analog and digital sections
The time of the analog section (hour/minute/24-hour hands) cannot be adjusted
1. Push the crown in to position 0. directly.
2. Rotate the crown to move the mode hand to point [TME] or [CAL]. Set the time of the area you want to indicate in the analog section once in the
• When [CAL] is selected, the calendar is displayed. digital section and then switch the time between the analog and digital sections.
• The second hand and the second indication displayed on the digital display are
3. Press and release the lower right button A or upper right always synchronized.
button B to select an area. 1. Push the crown in to position 0.
The selected area and its time or calendar are indicated on the digital display
and the area name display. 2. Rotate the crown to move the mode hand to indicate [TME] or
Table of time zones and representative areas [CAL].
• When [CAL] is selected, the calendar is displayed.
Area name Representative Time Area name Representative Time 3. Press and release the lower right button A or upper right
area zone area zone button B to select an area.
Coordinated TYO Tokyo +9 The time or calendar of the selected area is indicated on the digital display
UTC
Universal Time ±0 SYD Sydney +10 and the area name display.
LON London NOU Noumea +11
PAR Paris AKL Auckland +12
4. Press and release both the upper right button A and lower
ROM Rome
+1
HNL Honolulu -10
right button B at the same time.
CAI Cairo The time of the digital and analog (hour/minute/24-hour hands) sections
+2 ANC Anchorage -9
IST Istanbul
switches.
LAX Los Angeles -8
MOW Moscow
KWI Kuwait
+3 DEN Denver -7 Registering an area of a time zone you like
MEX Mexico City
-6 You can register one new area of a time zone on the world time of this watch.
DXB Dubai +4 CHI Chicago
KHI Karachi +5
• Check the time zone (based on the UTC) of the area you want to register
NYC New York
-5 beforehand.
DAC Dhaka +6 YUL Montreal • The time zone can be set in 1 hour units.
BKK Bangkok +7 CCS Caracas -4
SIN Singapore RIO Rio de Janeiro 1. Push the crown in to position 0.
-3
HKG Hong Kong +8 BUE Buenos Aires 2. Rotate the crown to move the mode hand to point [SET].
PEK Beijing
3. Pull the crown out to position 2.
• The time zone in the table is based on UTC (Coordinated Universal Time). The area name and the time zone of the area previously set are displayed on
• Countries or regions may change time zones for various reasons. the area name display and the digital display.
• “---” is indicated when they have not been
Setting the summer time set.
You can set the summer time for each area. 4. Press and release the upper right button B repeatedly to
• You cannot set the summer time for “UTC”.
change the target to be changed.
1. Push the crown in to position 0. • The target that is blinking is adjustable.
2. Rotate the crown to move the mode hand to point [TME]. 5. Rotate the crown to set the target.
• Input alphabets and numbers to indicate the new area name. Following
3. Press and release the lower right button A or upper right letters, numbers and symbols can be used.
button B repeatedly to indicate an area name you want to set Alphabet: A to Z
the summer time to. Numbers: 0 to 9
Symbols: “--” (hyphens) and “ ” (blank spaces)
4. Pull the crown out to position 2. • The time zone can be set from “-11” to “+12”.
The second hand points 0 second and the summer time setting starts • When you rotate the crown quickly, the indication will change continuously.
blinking. To stop the rapid change, rotate the crown.
5. Press and release the lower right button A. 6. Repeat steps 4 and 5 to set the area name and the time zone.
• Each time you press button A, the summer time ON/OF(OFF) changes
alternately.
7. Push the crown in to position 0.
6. Push the crown in to position 0 to finish the procedure. 8. Rotate the crown to move the mode hand to point [TME].
9. Press and release the lower right button A or upper right
button B repeatedly to select the area newly registered.
Deleting the registered area
Set the area name to “---”.
2/4
C650/C651/C652 Abbreviated instruction
8. Rotate the crown to move the mode hand to indicate [TME] to Using the chronograph
finish the procedure. Measuring up to 24 hours in 1/100 second increments.
• Measurement continues even after changing the mode.
Using the alarm
1. Push the crown in to position 0.
The alarm sounds for about 15 seconds at the time of the area you set.
• Alarm can be set separately at [AL-1], [AL-2], and [AL-3]. 2. Rotate the crown to move the mode hand to point [CHR].
The chronograph is ready on the digital section.
1. Push the crown in to position 0.
2. Rotate the crown to move the mode hand to point [AL-1], [AL-2], 3.
Use the chronograph.
or [AL-3]. Start/stop: press button B.
The area, alarm time and the alarm setting currently set are indicated. • Pressing button A during measurement indicates the split time for 10
seconds and “SPL” blinks on the digital display.
3. Press and release the lower right button A or upper right
button B repeatedly to select an area. Reset: press button A while the chronograph is stopped.
4. Pull the crown out to position 2. Be sure to reset chronograph and change the mode to [TME] or [CAL] after
The alarm setting turns to “ON” and it blinks. finishing measurement.
5. Press and release the upper right button B repeatedly to
change the target to be set.
• Each time you press button B, the target changes as follows:
3/4
C650/C651/C652 Abbreviated instruction
4/4