Professional Documents
Culture Documents
EIM-11 Q1 W2 Mod3
EIM-11 Q1 W2 Mod3
NAME: ______________________________________________________
GRADE & TRACK/STRAND: __________________________________
ADDRESS: __________________________________________________
CONTACT NUMBER: ________________________________________
STEEVE MARK L. MASAYON S.Y: 2020-2021
Teacher
0
How to Use this Competency Based Module?
Before you start answering the module, I want you to set aside other tasks
that will disturb you while enjoying the lessons. Read the simple instructions below to
successfully enjoy the objectives of this kit. Have fun!
1. Follow carefully all the contents and instructions indicated in every page of
this module.
2. Write on your notebook or any writing pad the concepts about the lessons.
Writing enhances learning that is important to develop and keep in mind.
3. Perform all the provided activities in the module.
4. Let your facilitator/guardian assess your answers.
5. Analyze conceptually the posttest and apply what you have learned.
6. Enjoy studying!
1
Parts of the Module
Expectations - These are what you will be able to know after completing the
lessons in the module.
Pre-test - This will measure your prior knowledge and the concepts to be
mastered throughout the lesson.
Looking Back - This section will measure what learnings and skills that you
understand from the previous lesson.
Brief Introduction- This section will give you an overview of the lesson.
Activities - These are activities designed to develop critical thinking and other
competencies. This can be done with or without a partner depending on the
nature of the activity.
Remember - This section summarizes the concepts and applications of the
lessons.
Checking your Understanding - It will verify how you learned from the lesson.
Post-test - This will measure how much you have learned from the entire
module.
2
Lesson 3: Prepare Electrical Tool and Materials
Expectations
Pre-test 3.1
I. Multiple Choice: Read each statement carefully. Then, Write the letter of the
correct answer before on the space provided. Use capital letter only and no
erasures.
_1. What will be the best tools to use, if you want to mount junction box in a
wooden wall?
A. Screwdriver B. Hammer C. Pliers D. Gimlet
_2. To remove the insulator of the TW #18 AWG solid cu. wire, what is the best
tool to use?
A. Pliers B. Wire stripper C. Blade cutter D. Hickey
_3. This is tools used in driving or pounding and pulling out nails.
A. Ballpeen hammers B. Claw hammer
C. Mallet (rubber head) D. Stubby screwdriver
3
_4. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in
making holes on metal sheets and concrete walls.
A. Electric power drill B. Portable electric drill
C. Power saw D. Portable grinder
_5. Johnny wants to bend a plastic pipe in 90degree. What is the best power
tools to use?
A. Electric stove B. Heat gun
C. Lighter D. Gas stove
_6. This is a metal box where all circuit breaker place.
A. Junction box B. Square box
C. Utility box D. Panel board
_7. An electrical material used as the passage of wires for protection and
insulation?
A. Connectors B. Clamps
C. Conduits D. Male plug
_8. It is used to attach metallic or non-metallic conduit to the junction or utility
boxes.
A. Connectors B. Clamps
C. Conduits D. Male plug
_9. This is a protective device used to automatically in trip position when trouble
in the circuit such as short circuit or overload occurs.
A. Circuit breaker B. Fuse
C. Electrical tape D. Bulb
_10. It is an octagonal shaped electrical material where the connections or
joints of wires are being done? It is also where the flush type lamp holder is
attached.
A. Junction box B. Square box
C. Utility box D. Panel board
II. Identification: Read the statement carefully and identify what is being described
or defined. Write your answer on the space provided.
4
8. This is a rectangular shaped metallic or plastic (PVC) material in
which flush type convenience outlet and switch are attached.
9. Are electrical materials used as the passage of wires for
protection and insulation?
10. Are used to attach metallic or non-metallic conduit to the
junction or utility boxes.
I. Identification: Read the statement carefully and identify what is being described
or defined. And write the answer before the number
Brief Introduction
5
Topic: Electrical Basic Hand Tools and Power
Tools
Objectives:
1. familiarize the different basic electrical hand tools and equipment;
2. use and select basic electrical hand tools and equipment in line with the job
specification; and
3. appreciate the value of basic hand and power tools.
Learning Content:
The following are common electrical tools and equipment needed in the
installation of electrical wiring.
SCREW DRIVERS- These tools are made of steel hardened and tempered at the tip
used to loosen or tighten screws with slotted heads. They come in various sizes and
shapes.
6
2) Philips Screwdriver- This has a cross tip resembling a positive (+)
sign. This is used to drive screws with cross slot heads.
7
HAMMERS- These are tools used in driving or pounding and pulling out nails. They
are made of hard steel, wood, plastic, or rubber. The following are types of hammer:
1) Claw hammer
3) Ballpeen hammer
PLIERS- These made from metal with insulators in the handle and are used for
cutting, twisting, bending, holding, and gripping wires and cables.
8
2) Side Cutting Pliers- This type of pliers is used for cutting fine,
medium and big wires and cables.
3) Long Nose Pliers- This is used for cutting and holding fine wires.
This can reach tight space or small opening where other pliers
cannot reach and used in making terminal loops of copper wires.
Wire Stripper- A tool used for removing insulation of medium sized wires ranging
from gauge #10 to gauge #16.
Electrician’s Knife- This is used by linemen to remove insulation of wire and cables
in low and high voltage transmission lines.
9
Portable Electric drill- A small drilling machine with a chuck capacity of ¼’’ and 3/8’’.
It is used in making holes on metal sheets and concrete walls.
Hacksaw- This tool is used to cut metal conduit and armored/shielded cable.
Steel tape rule - is a measuring tool used to measure the length of an object in
centimeter and inches.
10
Bender (Hickey) - a pipe bending apparatus.
Heat gun - A heat gun is a device used to emit a stream of hot air, usually at
temperatures between 100 °C and 550 °C (200-1000 °F), with some hotter models
running around 760 °C (1400 °F), which can be held by hand. Heat guns usually
have the form of an elongated body pointing at what is to be heated, with a handle
fixed to it at right angles and a trigger, in the same general layout as a handgun,
hence the name.
11
File - A file is a tool used to remove fine amounts of material from a workpiece. It is
common in woodworking, metalworking, and other similar trade and hobby tasks.
Most are hand tools, made of a case-hardened steel bar of rectangular, square,
triangular, or round cross-section, with one or more surfaces cut with sharp,
generally parallel teeth.
Gimlet - A gimlet is a hand tool for drilling small holes, mainly in wood, without
splitting.
Fuse puller - A fuse puller is a tool used to insert and remove electrical fuses from
their housing.
12
Pipe threader - Use to thread metallic pipe.
Soldering - tools are used in making splices and taps connections of wires.
Activity
Direction: Draw a minimum of 25 basic hand and power tools with function in long
bond paper.
Performance Rubrics
Criteria 3 2 1 Rating
Some of the Most of the
All drawings are drawings are drawings are
Appearance
creative/ artistic. moderately not creative
creative/ artistic. and artistic
Able to finish
Time Able to finish
Able to finish the the activity
the activity
Management activity exact to after the
ahead of time.
the given period. given period
13
Less than ½
No. of Above to the Exact to the to the
prescribed no. of prescribed no. of prescribed
drawings
drawings drawings no. of
drawings
TOTAL
Remember
Performance Rubrics
Criteria 3 2 1 Rating
14
Able to finish the
Able to finish the Able to finish the
Time activity after the
activity ahead of activity exact to
Management given period of
time. the given time.
time
Systematically Systematically
Cannot follow
follow the steps follow the steps
Process the steps
prescribed all the prescribes
prescribed.
time. sometimes.
Did not observe
Observed the
Observed the the safety
safety precaution
Safety safety precaution precaution
prescribed
all the time. prescribed all the
sometimes.
time.
Can act with Can act with
Can act with full confidence confidence
Acting Role of confidence according to according to
according to their role their role
their role. but have but have
some more
difficulties, difficulties.
The
The The
Moral Lesson presentation/vlog
presentation/vlog presentation/vlog
is very well
is well instructive is instructive
instructive
TOTAL
Objectives:
1. familiarize the different electrical wiring supplies and materials;
2. use and select electrical wiring supplies and materials in line with the job
specification ; and
3. appreciate the value of electrical wiring materials and supplies in line with the
job requirements.
Learning Content:
Electrical materials are developed and constructed for a special purpose such as to:
Lamp holders- devices that hold and protect the lamp and are also called as lamp
Sockets/ Receptacle. These come in many designs and sizes. They are classified as
flush, hanging (weatherproof/chain) and surface types.
17
Hanging chain type
Switch- devices that connects and disconnects the flow of electric current in the
circuit. There are many shapes, designs, and types and they are classified as
hanging, flush, and surface types.
Surface type
18
Fuse- a circuit protective device that automatically blows and cut the current when
and overload or short circuit happens
Circuit Breaker - a protective device used to automatically blow and cuts the current
when trouble in the circuit such as short circuit or overload occurs.
Bolt-on type
19
Utility Box- a rectangular shaped metallic or plastic (PVC) material in which flush
type convenience outlet and switch are attached.
Flat Cord- Is a duplex stranded wire used for temporary wiring installation and
commonly used in extension cord assembly. It comes in a roll of 150 meters and with
sizes of gauge # 18 and gauge #16 AWG (American wire gauge).
2. Solid- wire is made of a single strand of copper or aluminum wire. These are
used in wiring installation inside and outside the buildings.
20
Conduits/Pipes- electrical materials used as the passage of wires for protection and
insulation. These could be rigid metallic, flexible metallic conduit (FMC), rigid non-
metallic (PVC), and flexible non-metallic or corrugated plastic conduit (CPC).
Clamps- electrical materials used to hold and anchor electrical conduits in its proper
position.
PVC Connector
21
Activity
Performance Rubrics
Criteria 3 2 1 Rating
Some of the Most of the
All drawings are drawings are drawings are
Appearance
creative/ artistic. moderately not creative
creative/ artistic. and artistic
Able to finish
Time Able to finish
Able to finish the the activity
the activity
Management activity exact to after the
ahead of time.
the given period. given period
Remember
Using appropriate electrical wiring materials and supplies are very essentials
to know to avoid electrical hazards like electrical fire.
22
Checking Your Understanding
Direction: List down all the electrical wiring materials and supplies that you will be
found in the electrical plan below. Write you answer in the table below.
Source: https://www.google.com/url?sa=i&url=https%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv
%3DglwP2ZgyklE&psig=AOvVaw1
M4IFhSWmz0TbeuNZAFAyU&ust=1592917670673000&source=images&cd=vfe&ved=0CAIQjRxqFwoTCNDlv_6-
leoCFQAAAAAdAAAAABAP
23
Post Test 3.1
I. Multiple Choice: Read each statement carefully. Then, Write the letter of the
correct answer before on the space provided. Use capital letter only and no
erasures.
_1. What will be the best tools to use, if you want to mount junction box in a
wooden wall?
A. Screwdriver B. Hammer C. Pliers D. Gimlet
_2. To remove the insulator of the TW #18 AWG solid cu. wire, what is the best
tool to use?
A. Pliers B. Wire stripper C. Blade cutter D. Hickey
_3. This is tools used in driving or pounding and pulling out nails.
A. Ballpeen hammers B. Claw hammer
C. Mallet (rubber head) D. Stubby screwdriver
_4. A small drilling machine with a chuck capacity of ¼‖ to 3/8‖. It is used in
making holes on metal sheets and concrete walls.
A. Electric power drill B. Portable electric drill
C. Power saw D. Portable grinder
_5. Johnny wants to bend a plastic pipe in 90degree. What is the best power
tools to use?
A. Electric stove B. Heat gun C. Lighter D. Gas stove
_6. This is a metal box where all circuit breaker place.
A. Junction box B. Square box C. Utility box D. Panel board
_7. An electrical material used as the passage of wires for protection and
insulation?
A. Connectors B. Clamps C. Conduits D. Male plug
_8. It is used to attach metallic or non-metallic conduit to the junction or utility
boxes.
A. Connectors B. Clamps C. Conduits D. Male plug
_9. This is a protective device used to automatically in trip position when trouble
in the circuit such as short circuit or overload occurs.
A. Circuit breaker B. Fuse C. Electrical tape D. Bulb
_10. It is an octagonal shaped electrical material where the connections or
joints of wires are being done? It is also where the flush type lamp holder
is attached.
A. Junction box B. Square box C. Utility box D. Panel board
II. Identification: Read the statement carefully and identify what is being described
or defined. Write your answer on the space provided.
Reflective Learning
Direction: Write your reflection about the lesson on the space provided.
I learned that ….
____________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
_________________________________________________________
24
REFERENCES
25
Acknowledgement
First Edition 2020
Republic Act 8293, section 176 states that: No copyright shall subsist in any
work of the Government of the Philippines. However, prior approval of the
government agency or office wherein the work is created shall be necessary for
exploitation of such work for profit. Such agency or office may, among other things,
impose as a condition the payment of royalties.
26
27