Professional Documents
Culture Documents
Works Examcollection 201 Dumps 2022-Feb-13 by Dominic 86q Vce
Works Examcollection 201 Dumps 2022-Feb-13 by Dominic 86q Vce
https://www.2passeasy.com/dumps/201/
NEW QUESTION 1
A BIG-IP Administrator adds new Pool Members into an existing, highly utilized pool. Soon after, there are reports that the application is failing to load for some
users. What pool level setting should the BIG-IP Administrator check?
A. Availability Requirement
B. Allow SNAT
C. Action On Service Down
D. Slow Ramp Time
Answer: D
Explanation:
Option ABC is a global configuration, has nothing to do with the new pool member, select D after excluding
NEW QUESTION 2
Administrative user accounts have been defined on the remote LDAP server and are unable to log in to the BIG-IP device.
Which log file should the BIG-IP Administrator check to find the related messages?
A. /var/log/secure
B. /var/log/messages
C. /Nar/log/ltm
D. /var/log/user.log
Answer: A
NEW QUESTION 3
Interface 1.2 on a BIG-IP VE has a status of UNINITIALIZED. What is the reason for this status?
Answer: B
Explanation:
trunk is a portchannel, you need to add a physical interface.
NEW QUESTION 4
A virtual server is defined per the charts. The last five client connections were to members C, D, A, B, B. Given the conditions shown in the above graphic, if a
client with IP address 205.12.45.52 opens a connection to the virtual server, which member will be used for the connection.
A. 172.16.20.1:80
B. 172.16.20.2:80
C. 172.16.20.3:80
D. 172.16.20.4:80
E. 172.16.20.5:80
Answer: D
NEW QUESTION 5
A virtual server is listening at 10.10.1.100:any and has the following iRule associated with it:
when CLIENT_ACCEPTED { if {[TCP::local_port] equals 80 } { pool pool1 } elseif {[TCP::local_port] equals 443} { pool pool2 }
If a user connects to 10.10.1.100 and port 22, which pool will receive the request?
A. pool1
B. pool2
C. Non
D. The request will be dropped.
E. Unknow
F. The pool cannot be determined from the information provided.
Answer: D
NEW QUESTION 6
Some users who connect to a busy Virtual Server have connections reset by the BIG-IP system. Pool member resources are NOT a factor in this behavior. What is
a possible cause for this behavior?
Answer: C
Explanation:
The topic explains that the connection reset behavior is caused by the vs configuration rather than the server resource problem. The answers B C are all
configuration at the service forwarding level. If there is a problem with the configuration, it is all a problem rather than some users. Answer C's Connection Limit will
cause a reset behavior when the connection reaches the threshold.
NEW QUESTION 7
A BIGJP Administrator needs to load a UCS file but must exclude the license file. How should the administrator perform this task?
A. From the CLI with command U tmsh load /$ys ucs <ucs filename> no-license
B. From the GUI, select the UCS file, unchcck the license box, and click restore
C. From the CLI with command(tmos)« tmsh load /sys ucs <ucs filename> no-license
D. From the GUI, select the UCS file and click restore
Answer: A
NEW QUESTION 8
What is the status of a pool member when manual resume is enabled and a health check first fails and then passes?
A. Offline (Disabled)
B. Offline (Enabled)
C. Available (Disabled)
D. Available (Enabled)
Answer: A
NEW QUESTION 9
Which statement is true concerning a functional iRule?
Answer: B
NEW QUESTION 10
When configuring a pool member's monitor, which three association options are available? (Choose three.)
Answer: ADE
NEW QUESTION 10
A BIG-IP Administrator upgrades the BIG-IP LTM to a newer software version. After the administrator reboots into the new volume, the Configuration fails to load.
Why is the Configuration failing to load?
Answer: A
NEW QUESTION 15
Refer to the exhibit.
Answer: B
NEW QUESTION 16
A BIG-IP Administrator suspects that one of the BIG-IP device power supplies is experiencing power outages.
Which log file should the BIG-IP Administrator check to verify the suspicion?
A. /war /log/daemon.log
B. /var/log/kern.log
C. /var/log/ltm
D. /var/log/audit
Answer: C
NEW QUESTION 18
Refer to the exhibit.
During a planned upgrade lo a BIG-IP HA pair running Active/Standby, an outage to application traffic is reported shortly after the Active unit is forced to Standby
Reverting the flower resolves the outage. What should the BIG-IP Administrator modify to avoid an outage during the next for over event?
Answer: A
NEW QUESTION 19
A BIG-IP Administrator configures remote authentication and needs to make sure that users can still login even when the remote authentication server is
unavailable.
Which action should the BIG-IP Administrators in the remote authentication configuration to meet this requirement?
Answer: B
NEW QUESTION 24
A site has six members in a pool. All of the servers have been designed, built, and configured with the same applications. It is known that each client's interactions
vary significantly and can affect the performance of the servers. If traffic should be sent to all members on a regular basis, which loadbalancing mode is most
effective if the goal is to maintain a relatively even load across all servers?
A. Ratio
B. Priority
C. Observed
D. Round Robin
Answer: C
NEW QUESTION 27
A BIG-IP Administrator is conducting maintenance on one BIG-IP appliance in an HA Pair. Why should the BIG-IP Administrator put the appliance into
FORCED_OFFLINE state?
A. To preserve existing connections to Virtual Servers and reduce the CPU load
B. To allow new connections to Virtual Servers and ensure the appliance becomes active
C. To terminate connections to the management IP and decrease persistent connections
D. To terminate existing connections to Virtual Servers and prevent the appliance from becoming active
Answer: D
NEW QUESTION 29
Under what condition must an appliance license be reactivated?
Answer: B
NEW QUESTION 30
To increase available bandwidth of an existing Trunk, the BIG-IP Administrator is adding additional interfaces.
Which command should the BIG-IP Administrator run from within bosh shell?
Answer: D
NEW QUESTION 31
A 816-IP Administrator recently deployed an application Users are experiencing slow performance with the application on some remote networks.
Which two modifications can the BIG-IP Administrator make to address this issue? (Choose two)
Answer: BC
NEW QUESTION 32
A BIG-IP Administrator need to ensure that a pool member and down by the monitor the BIG-IP system sends existing connections to another be pool member.
Which should the BIG-IP Administrator perform to meet this goal?
A. Set Action on Service Down sing under the server configuration to reselect.
B. Reconfigure the pool motor members as UP.
C. Enable mirroring within the persistence profile.
D. Set Action Service Down setting under the pool configuration to reselect.
Answer: D
NEW QUESTION 33
A BIG-IP Administrator finds the following log entry after a report of user issues connecting to a virtual server: 01010201: 2: Inet port exhaustion on 10.70.110.112
to 192.28.123.250:80 (proto 6)
How should the BIG-IP Administrator modify the SNAT pool that is associated with the virtual server?
Answer: C
NEW QUESTION 34
How is persistence configured?
Answer: B
NEW QUESTION 35
DNS queries from two internal DNS servers are being load balanced to external DNS Servers via a Virtual Server on a BIG-P device. The DNS queries originate
from 192.168.101.100 and 192.168.101.200 and target 192.168.21.50
All DNS queries destined for the external DNS Servers fail
Which property change should the BIG-IP Administrator make in the Virtual Server to resolve this issue?
Answer: C
NEW QUESTION 37
Which statement is true concerning cookie persistence?
Answer: A
NEW QUESTION 41
A BIG-IP Administrator needs to restore an encrypted UCS archive from the command line using the TMSH utility.
Which TMSH command should the BIG-IP Administrator use to accomplish this?
Answer: A
NEW QUESTION 43
A Standard Virtual Server configured for an application reports poor network performance. This application is accessed mainly from computers on the Internet.
What should the BIG-IP Administrator configure on the Virtual Server to achieve better network performance?
A. Protocol Profile (Client) with f5-tcp-wan and Protocol Profile (Server) with f5-tcp-lan
B. Protocol Profile (Client) with f5-tcp-lan
C. Protocol Profile (Client) with fS-tcp-lan and Protocol Profile (Server) with f5-tcp-wan
D. Protocol Profile (Client) with f5-tcp-optimized
Answer: A
NEW QUESTION 44
Which two can be a part of a virtual server's definition? (Choose two.)
A. rule(s)
B. pool(s)
C. monitor(s)
D. node address(es)
E. loadbalancing method(s)
Answer: AB
NEW QUESTION 46
Refer to the exhibit.
The BIG-IP Administrator has modified an iRule on one device of an HA pair. The BIG-IP Administrator notices there is NO traffic on the BIG-IP device in which
they are logged into.
What should the BIG-IP Administrator do to verify if the iRule works correctly?
A. Push configuration from this device to the group and start to monitor traffic on this device
B. Pull configuration to this device to the cluster and start to monitor traffic on this device
C. Log in to the other device in the cluster, push configuration from it, and start to monitor traffic on that device
D. Log in to the other device in the cluster, pull configuration to it, and start to monitor traffic on that device
Answer: D
Explanation:
The device in the picture is a standby machine, of course there is no traffic, you need to log in to the host, and then pull the configuration to the host.
NEW QUESTION 51
Refer to the exhibit.
A BIG-IP Administrator creates a new Virtual Server to load balance SSH traffic. Users are unable to log on to the servers.
What should the BIG-IP Administrator do to resolve the issue?
Answer: B
NEW QUESTION 52
An LTM device has a virtual server mapped to www.f5.com with a pool assigned. Users report that when browsing, they are periodically required to re-login to
/resources/201.1.7.b.2_l.com. The objects are defined as follows:
Virtual server. Destination 192.168.245.100:443 netmask 255.255.255.0 Persistence: SSL session persistence
Profiles: HTTP/TCP
Which persistence method should the BIG-IP Administrator apply to resolve this issue?
Answer: A
NEW QUESTION 55
A virtual server at 10.10.1.100:80 has the rule listed below applied.
when HTTP_REQUEST { if {[HTTP::uri] ends_with "htm" } { pool pool1 } else if {[HTTP::uri] ends_with "xt" } { pool pool2 }
If a user connects to http://10.10.1.100/foo.txt which pool will receive the request?
A. pool1
B. pool2
C. Non
D. The request will be dropped.
E. Unknow
F. The pool cannot be determined from the information provided.
Answer: B
NEW QUESTION 58
A BIG-IP Administrator wants to add the ASM Module to an HA pair of BIG-IP devices. The BIG-IP Administrator has already installed a new Add-On License on
both devices in the HA pair. What should the BIG-IP Administrator do next to use the module?
Answer: A
NEW QUESTION 62
During a maintenance window, an EUD test was executed and the output displayed on the screen. The BIG-IP Administrator did NOT save the screen output. The
BIG-IP device is currently handling business critical traffic. The BIG-IP Administrator needs to minimize impact. What should the BIG-IP Administrator do to provide
the EUD results to F5 Support?
A. Boot the device into EUD then collect output from console
B. Execute EUD from tmsh and collect output from console
C. Collect file /var/log/messages
D. Collect file /shared/log/eud.log
Answer: D
NEW QUESTION 67
A BIG-IP Administrator needs to remove a pool specific health monitor. There is a pool named Best Pool with two members, one named Best pool member and
one named Best pool member2. In the Local Traffic section of the administrative GUI, which stops should the BIG-IP Administrator take to remove a pool level
monitor?
A. Pool > Pool List > Best Pool > Members > Health Monitors
B. Nodes > Node List> Best _pool_memberl > Heath Monitors
C. Monitors > Monitor Name> Instances
D. Pool > Pool List> Best Pool > Health Monitors
Answer: D
NEW QUESTION 69
A pool of four servers has been partially upgraded for two new servers with more memory and CPU capacity. The BIG-IP Administrator must change the load
balance method to consider more connections for the two new servers. Which load balancing method considers pool member CPU and memory load?
A. Round Robin
B. Dynamic Ratio
C. Ratio
D. Least Connection
Answer: C
NEW QUESTION 73
What is the purpose of MAC masquerading?
Answer: C
NEW QUESTION 76
You have a pool of servers that need to be tested. All of the servers but one should be tested every 10 seconds, but one is slower and should only be tested every
20 seconds. How do you proceed?
A. It cannot be don
B. All monitors test every five seconds.
C. It can be done, but will require assigning monitors to each pool member.
D. It cannot be don
E. All of the members of a pool must be tested at the same frequency.
F. It can be done by assigning one monitor to the pool and a different monitor to the slower pool member.
Answer: D
NEW QUESTION 77
A node is a member of various pools and hosts different web applications. If a web application is unavailable, the BIG-IP appliance needs to mark the pool member
down for that application pool. What should a BIG-IP Administrator deploy at the pool level to accomplish this?
Answer: C
Explanation:
Requiring all traffic to be HTTPS access requires HTTP requests to be redirected directly to HTTPS.
NEW QUESTION 82
A BIG-IP Administrator is checking the BIG-IP device for known vulnerabilities. What should the 8IG-IP Administrator upload to BIG-IP iHealth for further analysis?
A. QKView
B. EUD
C. UCS
D. tcpdump
Answer: A
NEW QUESTION 86
A BIG-IP Administrator suspects that one of the BIG-IP device power supplies is experiencing power outages.
Which log file should the BIG-IP Administrator check to verify the suspicion?
A. /war /log/daemon.log
B. /var/log/kern.log
C. /var/log/ltm
D. /var/log/audit
Answer: C
NEW QUESTION 87
A BIG-IP Administrator needs to collect HTTP status code and HTTP method for traffic flowing through a virtual server.
Which default profile provides this information?
A. HTTP
B. Analytics
C. Request Adapt
D. Statistics
Answer: A
NEW QUESTION 91
When initially configuring the BIG-IP system using the config utility, which two parameters can be set? (Choose two.)
Answer: DE
NEW QUESTION 95
All pool members are online. All other virtual server settings are at default What might after the load balancing behavior?
Answer: D
A. If the destination of the traffic does not match a virtual server, the traffic will be discarded.
B. If the destination of the traffic does not match a virtual server, the traffic will be forwarded based on routing tables.
C. If the destination of the traffic matches a virtual server, the traffic will be processed per the virtual server definition.
D. If the destination of the traffic matches a virtual server, the traffic will be forwarded, but it cannot be loadbalanced since no SNAT has been configured.
Answer: AC
A. ftppool
B. telnetpool
C. Non
D. The request will be dropped.
E. Unknow
F. The pool cannot be determined from the information provided.
Answer: D
A. Neve
B. Each virtual server has a maximum of one profile.
C. Ofte
D. Profiles work on different layers and combining profiles is common.
E. Rarel
F. One combination, using both the TCP and HTTP profile does occur, but it is the exception.
G. Unlimite
H. Profiles can work together in any combination to ensure that all traffic types are supported in a given virtual server.
Answer: B
Answer: B
Answer: D
A. 192.1.1.100
B. 192.1.2.2
C. 192.1.1.1
D. 192.1.2.1
Answer: C
Answer: A
A. All of the pool member nodes are responding to the ICMP monitor as expected.
B. Less than 50% of the pool member nodes responded to the ICMP echo request.
C. All of the members of the pool have had their content updated recently and their responses no longer match the monitor.
D. Over 25% of the pool members have had their content updated and it no longer matches the receive rule of the custom monito
E. The other respond as expected.
Answer: D
According to the shown Configuration Utility stings What is the setting of the User Directory configuration under the Authentication submenu?
A. Local
B. Managed
C. Remote-TACACS+
D. Default system configuration
Answer: C
Answer: B
Answer: ABF
A. bigip.license file
B. QKViewfile
C. Device root password
Answer: B
Answer: D
A. CLIENT_ACCEPTED
B. HTTP_RESPONSE
C. HTTP_REQUEST
D. SERVER_CONNECTED
Answer: C
Explanation:
According to the UR! distribution is the category of HTTP requests, need to trigger HTTP_REQUEST event.
Answer: A
Answer: C
Answer: C
A. TCP
B. HTTP
C. HTTPS
D. ClientSSL
E. ServerSSL
F. CookieBased Persistence
Answer: ABDF
A BIG-IP Administrator creates a new Virtual Server. The end user is unable to access the page. During troubleshooting, the administrator learns that the
connection between the BIG-IP system and server is NOT set up correctly.
What should the administrator do to solve this issue?
Answer: C
Explanation:
The status of the pool can be seen that the members are all up, indicating that the network from F5 to the server is no problem, so there is no need to configure
selfip on the same subnet. The monitor is normal but the access is not normal, you have to consider the problem of snat, you can configure automap or configure
snat and specify snat ip.
A. A virtual server with an LACP profile and the switches' management IPs as pool members.
B. A virtual server with an LACP profile and the interfaces connected to the switches as pool members.
C. A Trunk listing the allowed VLAN IDs and MAC addresses configured on the switches.
D. A Trunk containing an interface connected to each switch.
Answer: D
A. Terminating SSL at the BIG-IP can eliminate SSL processing at the web servers.
B. Terminating SSL at IP the eliminates BIG all unencrypted traffic from the internal network.
C. Terminating SSL at the BIG-IP eliminates the need to purchase SSL certificates from a certificate authority.
D. Terminating SSL at the BIG-IP eliminates the need to use SSL acceleration hardware anywhere in the network.
Answer: A
Assume a virtual server has a ServerSSL profile. What SSL certificates are required on the BIG-IP?
Answer: A
The 816-IP Administrator runs the command shown and observes a device trust issue between BIG-IP devices in a device group. The issue prevents config sync
on device bigip3.local.
What is preventing the config sync?
Answer: A
Explanation:
Option A should be bioip3.local?. if choose bigip3.local, you should choose A.
Answer: C
Answer: A
A. The active system will restart the bigd daemon and continue in active mode.
B. The active system will restart the tmm daemon and continue in active mode.
C. The active system will reboot and the standby system will go into active mode.
D. The active system will failover and the standby system will go into active mode.
E. The active system will continue in active mode but gather member and node state information from the standby system.
Answer: ACD
A. The source address would not change, but the destination address would be translated to the origin address.
B. The destination address would not change, but the source address would be translated to the origin address.
C. The source address would not change, but the destination address would be translated to the NAT's address.
D. The destination address would not change, but the source address would be translated to the NAT's address.
Answer: A
A. The client IP address is unchanged between the client side connection and the serverside connection.
B. The server IP address is unchanged between the client side connection and the serverside connection.
C. The TCP ports used in the client side connection are the same as the TCP ports serverside connection.
D. The IP addresses used in the clientside connection are the same as the IP addresses used in the serverside connection.
Answer: A
Answer: D
The network team creates a new VLAN on the switches. The BIG-IP Administrator needs to create a configuration on the BIG-IP device. The BIG-IP Administrator
creates a new VLAN and Self IP, but the servers on the new VLAN are NOT reachable from the BIG-IP device.
Which action should the BIG-IP Administrators to resolve this issue?
Answer: C
Answer: B
A connection is being established to IP 1.1.1.1 on port 8080. Which virtual server will handle the connection?
A. fwd_8080_vs
B. host_vs
C. host_ 8080_VS
D. fwdvs
Answer: B
Answer: D
An LTM device has a virtual server mapped to www.f5.com. Users report that when they connect to
/resources/201.1.2h.l_l.com they are unable to receive content. What is the likely cause of the issue?
A. The pool associated with the virtual server does not have priority group activation enabled.
B. The virtual address does not have ARP enabled.
C. The virtual address does not have route advertising enabled.
D. The pool associated with the virtual server is falling its health check.
Answer: B
Answer: B
Explanation:
Because it is a web application, you can insert the source IP in the xff field in the http profile.
Answer: C
A. Four
B. Three
C. One
D. Two
Answer: B
A BIG-IP Administrator configures a now VLAN on an HA pair of devices that does NOT yet have any traffic. This action causes the assigned traffic group to fail
over to the standby device.
Which VLAN setting should be changed to prevent this issue?
Answer: B
A. bandwidth utilization
B. duplicate IP address
C. CPU utilization percentage
D. VLAN communication ability
Answer: D
A. Interfaces
B. Network routes
C. VLANS
D. IP addresses
Answer: A
Explanation:
trunk is a portchannel, you need to add a physical interface.
Answer: B
Answer: A
Answer: B
Answer: ABC
A. The active device will take the action specified for the failure.
B. The standby device also detects the failure and assumes the active role.
C. The active device will wait for all connections to terminate and then failover.
D. The standby device will begin processing virtual servers that have failed, but the active device will continue servicing the functional virtual servers.
Answer: A
A. SSL termination could not be performed if the virtual server's port was not port 443.
B. Virtual servers with a ClientSSL profile are always configured with a destination port of 443.
C. As long as client traffic was directed to the alternate port, the virtual server would work as intended.
D. Since the virtual server is associated with a ClientSSL profile, it will always process traffic sent to port 443.
Answer: C
Answer: C
Answer: CE
A. Option A
B. Option B
C. Option C
D. Option D
Answer: A
Answer: A
A. Least Sessions
B. Least Connections (member)
C. Fastest (node)
D. Weighted Least Connections (member)
Answer: D
Answer: C
Answer: B
Visit Our Site to Purchase the Full Set of Actual 201 Exam Questions With Answers.
We Also Provide Practice Exam Software That Simulates Real Exam Environment And Has Many Self-Assessment Features. Order the 201
Product From:
https://www.2passeasy.com/dumps/201/
* 201 Most Realistic Questions that Guarantee you a Pass on Your FirstTry
* 201 Practice Test Questions in Multiple Choice Formats and Updatesfor 1 Year