Professional Documents
Culture Documents
Csi e 550 E550 E550cr E550pm E550crpm 2016 en
Csi e 550 E550 E550cr E550pm E550crpm 2016 en
Csi e 550 E550 E550cr E550pm E550crpm 2016 en
E550 CR
E550 PM
E550 PM CR Automatic Edgebander with chain feeding system
E550 Automatic edgebander with chain feed
Chain feeding system
Maximum finishing quality Pre-milling
Corner rounding unit
E550
Chain feeding system
3 free spaces for finishing units Logic functioning controlled by PLC
3 free spaces for finishing units
3 mm edge coils
110 mm minimum panel length
1
Free space
1
Free space
1
Free space
HF 12000 RPM
systems. 1
Free space
1
Free space
1
Free space
HF 12000 RPM
HF 12000 RPM
DIAMOND tools 6 heating elements to 2 blades for perfect front/rear The system “reads” the edge Spray function Uniform colouring and
Ø = 60 mm H = 52 mm guarantee uniform end trimming on all types of thickness, making mistakes controlled by PLC finishing even on processed
glue temperature edges impossible! 2 sprayers (lower and upper) edges
HF motors 200 Hz
– 12.000 rpm Motorized glue spreading roller Operating cycle Rapid changeovers working and liquid tank 2 motors for buffing unit
– 0.75 kW (each) with an internal electrical controlled by PLC between radius milling, thin diameter 120 mm rotating
heating element and solid edges. at 1.400 rpm
Dedicated suction HF motor 200 Hz
system and blower Teflon-coated glue pot – 12.000 rpm – 0.22 kW 2 HF motors 200 Hz
for panel cleaning to permit complete Integrated suction system – 12,000 rpm – 0.37 kW
before glueing and rapid cleaning
Firm grip of panel guaranteed by special non-slip rubber on the pads. HF 12000 RPM
E550 PM 1 1 1
Linear feeding ensured by double sliding tracks with a special
Free space Free space Free space
HF 12000 RPM
HF 12000 RPM
Long lasting monolithic frame fully processed only in one cycle on E550 PM CR 1
Free space
1
Free space
1
Free space
Technical features
End trim unit with vertical corner rounding function (opt.) Min./max. panel height min. 8 – max. 50 mm
Min./max. edge thickness 0.4 – 3 mm (coils) / 0.4 – 3 mm (strips)
TWO PROCESSINGS IN ONE STEP Panel width min. 95 mm
Infeed and outfeed excess edge on panel being Panel length (Side being processed) min. 110 mm
processed is vertically milled with a diamond Panel feed speed 9 m/min
shaped tool Pre-milling motors (each) 200 Hz – 12.000 rpm – 0.75 kW
Glue pot heating element 1315 W – 6 cartridges
2 manual processing modes; straight and radius
End trimming motor 200 Hz – 12.000 rpm – 0.22 kW
High frequency motor 0,55kW – 12.000 RPM Flush trimming motors (each) 200 Hz – 12.000 rpm – 0.37 kW
Double copying system; horizontal and frontal Cutterblocks with combined WIDIA disposable Knives (radius/bevelled) ø 75 mm Z4 – hole ø 16 mm (r = 2–3 mm)
Total power installed 5 kW approx.
Weight 525 Kg approx.
Overall dimensions
200 cm
L2
E550 261 313
95 cm
E550 PM 261 313
E550 CR 311 363
SPECIAL OPERATIONS ALL UNITS UNDER CONTROL L1
Permits to apply edges on panels with cavities to hold The internal led lights on the units allows to E550 PM CR 311 363
hardware (also allows to apply edges on acute angle make adjustments in safety, even with bad
panels). outside lighting.
Both upper and lower copiers are fitted with
3 bearings which guarantee 3 support points We reserve the right to make technical modifications. The machines illustrated may include fittings and accessories not included on standard machine versions.
For photographic purposes, some units are shown without protections. Machines must however always be used with all protections fitted and operative.
for perfect copying in each situation.
Casadei Industria Group
www.casadei-industria.com
TECHNOLOGY FOR
WOODWORKING BUILDING/ARCHITECTURE V I S U A L C O M M U N I C AT I O N
S.p.a.