Professional Documents
Culture Documents
Manual
Manual
Manual
E3Z
Compact Sensor Offers Long Sensing
Distance and Superior
Noise-Immunity
D Photo-IC provides long sensing distance: 15 m and
10 m for through-beam, 4 m for retroreflective, and 1 m
for diffuse.
D Integrated Photo-IC improves noise immunity to
interference from inverters and other inductive loads.
D New injection molding technology assures IP67 rating
to withstand water and dust.
D Switch-selectable, Light-ON/Dark-ON operation.
D M8 connector-ready and 2 m, pre-wired models.
D NPN or PNP output models available.
Ordering Information
J Sensors
Stock Note: Shaded models are normally stocked.
Sensing
g method Light
g source Appearance
pp Connection method Sensing
g distance Model
NPN output PNP output
Through-beam
g IR/RED
/ Pre-wired 15 m (IR)
( ) E3Z-T61(A) E3Z-T81(A)
Connector 10 m (RED) E3Z-T66(A) E3Z-T86(A)
(See Note 1.)
1)
Pigtail 3 pin (M8) E3Z--T61(A)--M5J E3Z--T81(A)--M5J
www.DataSheet4U.com Pigtail 4 pin (M8) E3Z--T61(A)--M3J E3Z--T81(A)--M3J
Pigtail 4 pin (M12) E3Z--T61(A)--M1J E3Z--T81(A)--M1J
Polarized RED ((See Note 2.)) Pre-wired 100 mm to 4 m E3Z-R61 E3Z-R81
retroreflective
fl i Connector 100 mm to 3 m E3Z-R66 E3Z-R86
(See Note 3.)
3)
Pigtail 3 pin (M8) E3Z--R61--M5J E3Z--R81--M5J
Pigtail 4 pin (M8) E3Z--R61--M3J E3Z--R81--M3J
Pigtail 4 pin (M12) E3Z--R61--M1J E3Z--R81--M1J
Diffuse IR Pre-wired 5 to 100 mm E3Z-D61 E3Z-D81
reflective
fl i Connector ( id view)
(wide i ) E3Z-D66 E3Z-D86
Pigtail 3 pin (M8) E3Z--D61--M5J E3Z--D81--M5J
Pigtail 4 pin (M8) E3Z--D61--M3J E3Z--D81--M3J
Pigtail 4 pin (M12) E3Z--D61--M1J E3Z--D81--M1J
Pre-wired 1m E3Z-D62 E3Z-D82
Connector E3Z-D67 E3Z-D87
Pigtail 3 pin (M8) E3Z--D62--M5J E3Z--D82--M5J
Pigtail 4 pin (M8) E3Z--D62--M3J E3Z--D82--M3J
Pigtail 4 pin (M12) E3Z--D62--M1J E3Z--D82--M1J
Note: 1. Model numbers that end with (A) are red LED versions.
2. The Reflector is sold separately. Select the Reflector model most suited to the application.
3. Sensing distance can be extended to 4 meters when the E39-R1S reflector is used. The sensing distance is 3 meters when the
E39-R1 reflector is used.
Slit width Sensing distance (typical) Minimum sensing object (typical) Model
0.5 mm dia. 50 mm 0.5 mm dia. E39-S65A
1 mm dia. 200 mm 1 mm dia. E39-S65B
2 mm dia. 800 mm 2 mm dia. E39-S65C
0.5×10 mm 1m 0.7 mm dia. E39-S65D
1×10 mm 2.2 m 1.2 mm dia. E39-S65E
2×10 mm 5m 2.4 mm dia. E39-S65F
Note: The actual sensing distance may be reduced to approximately 70% of the typical sensing distance when using a Reflector other
than the E39-R1 or the E39-R1S.
www.DataSheet4U.com
www.DataSheet4U.com
Vertical protective cover E39-L98
bracket
Adjustable height and angle E39-L93XY
bracket for sensors; free
range of X and Y axis posi-
tioning; no base included for
vertical post
Note: If a through-beam model is used, order two Mounting Brackets — one for the emitter and one for the receiver.
J M12 CONNECTORS
Appearance Cable type Model
Straight
g 2 m (6.56 ft) Four-wire type
yp Y96E--44SD2
5 m (16.40 ft) Y96E--44SD5
Right
g angle
g 2 m (6.56 ft) Y96E--44RD2
5 m (16.40 ft) Y96E--44RD5
www.DataSheet4U.com
Note: 1. Sensing distance can be extended up to 4 meters when the E39-R1S reflector is used.
2. Sensing distance can be extended up to 3 meters when the E39-R1 reflector is used.
3. Sensing distance is 10 meters when using the (A) versions (visible red LED, 660 nm).
Operation
J Output Circuits
Model E3Z-T61/-T66/-R61/-R66/-D61/-D66/-D62/-D67
NPN output Through-beam receiver Through-beam emitter
Retroreflective model
Diffuse reflective model
Power indicator (orange)
Brown
Brown 12 to 24 VDC
Operation
indicator Stability
indicator Load
Orange Green (Relay)
100 mA
Control output Black max.
Main Main
12 to 24 VDC
circuit circuit
Blue
0V
Blue
Model E3Z-T81/-T86/-R86/-D81/-D86/-D82/-D87
PNP output Through-beam receiver Through-beam emitter
Retroreflective model
Diffuse reflective model
Power indicator (orange)
Brown 12 to 24 VDC Brown
Operation
indicator Stability
indicator
Orange Green
Black
www.DataSheet4U.com Main Control output 100 mA Load Main
12 to 24 VDC
circuit max. (Relay) circuit
Blue
0V
Blue
Connector pin
arrangement
Pin 2 is open. Pins 2, 4 are open.
J Timing Charts
Light-ON (L-ON) Operation Dark-ON (D-ON) Operation
Incident Incident
Interrupted Interrupted
Operation ON Operation
indicator ON
OFF indicator
(orange) (orange) OFF
Output ON ON
Output
transistor
OFF transistor OFF
Wire colors
Brown
White
Blue
Black
Y96E--44SD2 Y96E--44RD2
Y96E--44SD5 Y96E--44RD5
www.DataSheet4U.com
E39-RS3
E39-RS2
Distance Y (mm)
Distance Y (mm)
Distance Y (mm)
2-dia. slit E39-RS1
Black
carbon
Distance Y (mm)
Distance Y (mm)
Black carbon
White drawing paper White drawing paper SUS
SUS (glossy surface)
(glossy surface)
Sensing target:
100 x 100 mm white paper
Excess gain ratio
E39-R3 E39-R1S
E39-R1
Sensing target:
300 x 300 mm white paper
Excess gain ratio
Distance X (m)
White paper
SUS (glossy
SUS (glossy surface)
Distance (mm)
surface)
Distance (m)
White paper
Black paper
Black paper
J Sensors
Through-beam (Pre-wired Models) Through-beam (Connector Models)
E3Z-T61 20
E3Z-T66 20
E3Z-T81 (0.79) E3Z-T86 (0.79)
10.8 10.8
Emitter (0.43) Emitter (0.43)
Power indicator (orange) Power indicator (orange)
17 17
Lens (0.67) Lens (0.67)
Optical axis Optical axis
31
(1.22) 31
(1.22)
Two, M3 Two, M3
Vinyl-insulated round cable with two
conductors, 4 dia. (0.2 mm2 with M8
1.1-dia. insulator); standard length: 2m connector
20 20
(0.79) (0.79)
10.8 10.8
(0.43) (0.43)
Operation
selector Operation selector
Receiver Stability indicator
Sensing adjuster Receiver Stability indicator
Sensing adjuster
(green) (green)
17 17
Lens (0.67) Lens (0.67)
Optical axis
Optical axis
31
31 (1.22)
(1.22)
Two, M3 Two, M3
Vinyl-insulated round cable with three
conductors, 4 dia. (0.2 mm2 with M8
1.1-dia. insulator); standard length: 2m connector
31 31
(1.22) (1.22)
J Slits
E39-S65A E39-S65D
E39-S65B E39-S65E
10.4 10.4
E39-S65C (0.41) E39-S65F (0.41)
32.2
32.2 (1.27)
(1.27) 15.5
15.5
(0.61) (0.61)
J Reflectors
E39-R1
E39-R1S
40.3 (1.59) 7.5
Two, 3.5 dia. 34 (1.34) (0.30)
5.2
(2.05)
59.9
(2.36)
Material
Surface: Acrylic resin 2.7
1.6 (0.06)
Backside: ABS resin (0.11)
E39-R2
80.8 (3.18) 7.5
Four, 3.5 dia. 74.5 (2.93) (0.30)
7 7
8
www.DataSheet4U.com 59.9
(2.36)
52
(2.05)
Material
Surface: Acrylic resin 7 (0.28) 2.7
Backside: ABS resin 1.6 (0.06) (0.11)
6.5 (0.26) 34 (1.34)
42.3
(1.67)
21
8
(0.31)
15 3.5 (0.14)
4 (0.16)
25 (0.98) 5.5 (0.22)
Material
Reflecting surface: Acrylic resin 35.4 (1.39)
Back: ABS resin 8 (0.31)
61.4
(2.42)
30.4
(1.20)
10 (0.39)
J Miniature Reflector
E39-R3 29 (1.14)
6 3.4
4.5
3.4
13.7
14°
7 (0.54)
18.45 0.2
22.9 20
Material (0.90) (0.79)
Surface: Acrylic resin
Backside: ABS resin
Adhesive
11 tape side 0.2
22.5
(0.89)
19.3 16
(0.63)
Two,
3.2 34.8
41.8 dia. 34
(1.65) (1.37)
Two, M3 (1.34)
25.4 38
(1.00) (1.50) 3.4
10.1 SUS304
2.6 stainless
(0.40) 1.2 10°
1.2 steel
www.DataSheet4U.com
J Tape Reflectors
E39-RS1 E39-RS3
35 (1.38) 0.6
(0.02)
10 80 (3.15)
(0.39) 0.6
Material: (0.02)
Acrylic resin
Adhesive
tape side
E39-RS2
40 (1.57) 0.6
(0.02)
70
(2.76)
35
(1.38)
Material:
Acrylic resin
Material:
Adhesive Adhesive
Acrylic resin
tape side tape side
J Mounting Brackets
E39-L104
29 (1.14)
13.7 13.7
(0.54) (0.54) With Mounting Bracket
7
(E3Z-D62)
29 (1.14) (0.28)
16
(0.63) Two, 3.2 dia. Optical Two, M3
axis
Material:
SUS304 31
stainless steel 39 (1.22) 25.4
(1.54) 38.3 (1.00)
37.8 (1.51)
8.8 (0.35)
1.2
(0.05)
E39-L43
25.4 40 25.4
Four, 3.2 dia. (1.00) 40 (1.57) (1.00)
(1.57) Optical
7.5
axis
(0.3)
7.5 (0.3) 15
15
(0.59)
(0.59)
1.2
Material: 13 (0.05)
SUS304 (0.51)
stainless steel
13
(0.51)
www.DataSheet4U.com
E39-L44 With Mounting Bracket
(E3Z-D62)
10.8
16.2 (0.43) 14.1
(0.64) 20 (0.56)
8.7 23.2 (0.79)
(0.34) 9 23.2 Two, 9
(0.91) Optical
1.2 (0.05) (0.35) (0.91) M3 (0.35)
axis
25.4
3.2 dia.
18 36 36 (1.00) 31
Material: 18
(0.71) (1.42) (1.42) (1.22)
SUS304 (0.71)
35.3
stainless steel (1.39)
21 23
2-50° (0.91) 10.5
(0.41)
14.2
(0.56)
Optical 12.3 3.5
axis (0.48) (0.14)
38.5
(1.52) 25.4
(1.00)
1.5 25.4
Material: (0.06) (1.00)
SUS304 stainless steel 20
(0.79)
5°
7.3
(0.28)
14
E39-L142 (0.55)
With Sensor
8.7
(0.34) (Example: E3Z-L61)
7 6.9
22 (0.87) (0.27)
15.8 14
(0.62) (0.55) Four
3.4 dia.
Optical
axis
37 25.4
(1.46) (1.00)
55
(0.22)
28
15.3 (0.60) (1.10)
14°
4.5
Material: 4.5
SUS304 stainless steel 1.5 12 5.0
(0.06) (0.47) 4.0
4.5
7.8
www.DataSheet4U.com
E39-L93FH
26
48
20.7 (1.89)
8
15°
15°
215 Ø12
(8.46)
188
183 (7.40)
(7.20)
54 59
30 (2.32)
6
35
2--Ø6.6
50
(1.97) 45
26 22.5
48
E39-L93FV 26.1 48
(1.89)
20.7
8
15°
15°
www.DataSheet4U.com
208
(8.19) Ø12
181
176 (7.13)
(6.93)
48 53
(2.09)
24
12
35 2--Ø6.6
50
53 22.5
(2.09)
29
8
15°
15°
216
(8.50) Ø12
189
184 (7.44)
(7.24)
54 59
30 (2.32)
2--Ø6.6
34 27
10
14
32
45
E39-L93V 26.1
48
20.7 (1.89)
8
15°
15°
208 Ø12
(8.19)
www.DataSheet4U.com
176 181
(6.93) (7.13)
49
44 (1.93)
20
10
32 2--Ø6.6
46
48
(1.89)
15 8
24
E39-L93XY
197
(7.76)
165 8
22
20
15
35
21 26
40
(1.51)
170
(6.69) 15°
15°
8
24
11
48
Ø12
189 213
(7.44) (8.39)
Ø12
Note: The E39-L93XY consists of a vertical post, x-y joint, 2 nuts, 2 bolts and sensor mounting attachment. There is no base for the bot-
tom of the vertical post.
E39-L98
Mounting Holes
Two, M6
56 dia.
(2.2)
www.DataSheet4U.com
(1.73¦0.01)
Screw provided
Material: 61 25.4 20
SUS304 stainless steel (2.4) (1.00) (0.79)
35.3
(5.33)
16
(0.63)
56 (2.2)
34 (1.34)
LENGTH
Right Angle
Y96E--M833RD2 .72” REF
Ø.39” REF
[10.00mm]
Straight 21.5
XS3F-M421-402-A (L=2 m) 9 dia.
(0.35)
(0.85) 30 5
XS3F-M421-405-A (L=5 m) 31.4
(1.24)
50 (1.97)
50 (1.97)
23.1
(0.91) 30 5
3.4
2.15
0.5
1.95
www.DataSheet4U.com
14.7 31.24
(0.58) (1.23)
M12 1 -- Brown +V 3 -- Blue 0V
Right Angle thread
Y96E--44RD2 (L=2 m)
4 -- Black Output
Y96E--44RD5 (L=2 m) Gold/palladium/
nickel--plated
brass contaccts
J Operating Environment
Do not use the Sensor in locations with explosive or flammable
gas.
J Settings
E3Z-jjj E39-L104 Mounting Bracket
Power Reset Time (sold separately)
www.DataSheet4U.com
Protruding
portion
Lower
indented
Slit portion
Sensor
Mounting Method
1. Hook the upper protruding portion of the Slit to the upper indented mounting portion of the Sen-
sor and adjust the position of the Slit so that the Slit will be in parallel to the lens side of the
Sensor.
2. Press the lower protruding portion of the Slit onto the indented mounting portion of the Sensor
until the Slit snaps in.
Removal Method
1. Press the upper portion of the Slit.
2. Disconnect the lower protruding portion of the Slit from the Sensor and remove the Slit.
www.DataSheet4U.com
Complete “terms and conditions of sale” for product purchase and use are on Omron’s website at
www.omron.com/oei -- under the “About Us” tab in the Legal Matters section.
NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.
R
OMRON ELECTRONICS LLC OMRON CANADA, INC. OMRON ON--LINE
One East Commerce Drive 885 Milner Avenue Global -- http://www.omron.com
Schaumburg, IL 60173 Toronto, Ontario M1B 5V8 USA -- http://www.omron.com/oei
847-843--7900 416-286-6465 Canada -- http://www.omron.com.ca
For US technical support or other inquiries:
800-556--6766
Cat. No. E308--E3--3 10/04 Specifications subject to change without notice. Printed in U.S.A.