Professional Documents
Culture Documents
06 Gyplyner Walls
06 Gyplyner Walls
208
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 209
GypLyner™
Key facts
3
● Corrects background irregularities
● Minimal connection to the structure
● Can satisfy National Building Regulations on
1
thermal performance
● Can be used to upgrade the sound resistance and
thermal insulation
● Versatile, general purpose lining
2
● Little or no background preparation needed
● Commonality of ceiling and wall lining
components
209
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 210
www.gypsum.ie
GypWall™ CLASSIC
GypLyner™ Components
Gyproc board products Gypframe metal products
Gyproc WallBoard1,2 Gypframe GL1 Lining Channel
Thickness 12.5, 15mm
Width 1200mm
6 1 Moisture resistant boards are specifed in intermittent wet use areas 2 Also available in DUPLEX grades where a vapour check is required.
210
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 211
GypLyner™
Gypframe metal products Fixing and finishing products
Gypframe 99 FC 50 Fixing Channel Gyproc Wafer Head
Drywall Screws
For metal-to-metal fixing up to 0.79mm
thick
Gypframe GFS1 Fixing Strap
Gypframe GL11 GypLyner Anchors
For fixing Gypframe GL2 or GL9 Brackets
to concrete / masonry
Gypframe GFT1 Fixing 'T'
Gyproc Drywall Screws
For fixing boards to stud framing up to
0.79mm thick
211
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 212
www.gypsum.ie
GypWall™ CLASSIC
GypLyner™ Components
Fixing and finishing products Fixing and finishing products
212
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 213
GypLyner™
Construction tips
● Depth of the cavity is determined by the fixing brackets. Allow a stand-off of 25mm - 75mm, plus the lining
thickness, for a Gypframe GL2 Bracket and 25mm - 125mm, plus the lining thickness, for a Gypframe GL9 Bracket
● Keep the drylining cavity closed to prevent downgrading the thermal performance - where required apply a
continuous band of Gyproc Compound or Gyproc Sealant to the perimeter of external walls, around service
penetrations, openings, junctions and around the perimeter of suspended timber floors
● Use full height boards where possible - if joints are unavoidable, position them above suspended ceilings or below
access floor level where possible
● Support horizontal joints with Gypframe GFS1 Fixing Strap, Gypframe 99FC50 Fixing Channel, or Gypframe GFT1
Fixing ‘T’ (where specified).
213
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 214
www.gypsum.ie
CLASSIC
GypLyner™
Installation
GypWall™
1 2 3
• Use a straight edge (e.g. Gypframe • Determine cavity depth required and • Fix Gypframe GL8 Track to perimeters,
GL1 Lining Channel) to determine the mark chalk lines to floor and ceiling to with the longer leg towards the lining,
maximum undulation in the wall or indicate positioning of Gypframe GL8 at 600mm centres using appropriate
service protrusion. This will determine Track. fixings.
the minimum cavity depth.
214
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 215
GypLyner™
4 5 6
• Mark vertical lines on the wall at • Cut Gypframe GL1 Lining Channels to • Bend bracket legs forward and fix
600mm intervals (450mm intervals for size and round-off ends with tin snips each leg to the channel using a Gyproc
900mm width boards) to indicate for an easier fit. Wafer Head Drywall Screw. Insert screw
bracket fixing centres. through the hole in the bracket nearest
• Extend Gypframe GL1 Channels, to the back of the channel (See
• Mark horizontal lines at 800mm where required, by engaging channel
Construction details , Figure 18).
centres to determine individual bracket ends over a Gypframe GL3 Channel
position. Connector. NB Avoid exerting any backwards or
forwards pressure on the channels
• Position each bracket, ribs to the wall, NB Additional Gypframe GL1 Lining
when screw-fixing the brackets,
and fix through bracket slot into the Channels may be required to pick up
masonry wall using a Gypframe GL11 fixings for subsequent adjacent linings. otherwise a straight and true lining
GypLyner Anchor. surface may not be achieved. 6
• Friction fit Gypframe GL1 Lining
Channel into the track.
215
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 216
www.gypsum.ie
GypLyner™
GypWall™ CLASSIC
7 8 9
216
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 217
GypLyner™
10 11 12
www.gypsum.ie
GypLyner™
GypWall™ CLASSIC
13 14 15
• Fix Gyproc edge bead to the perimeter • Cut reveal and soffit boards to width, • Where openings occur in the run of
of the window frame to provide edge locate into the perimeter edge bead and lining, cut board around the opening to
restraint and protection to the reveal and fix into the Gypframe GL9 Channel and avoid a joint directly in line with edge of
soffit linings. Gypframe GL8 Track. openings.
• Fix boards to complete drylining at the • Ensure vertical board joints above door
opening. opes are supported by Gypframe GL1
Channels.
218
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 219
GypLyner™
16 17
219
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 220
www.gypsum.ie
CLASSIC
GypLyner™
Construction details
GypWall™ 1
3 4
125mm (maximum
stand-off) to face of
channel
220
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 221
GypLyner™
9 3
1
8 4
3 5
3 6
7
4 7
1
7
1 Gypframe GL1 Lining Channel 4 Gypframe GL2 or GL9 Bracket 7 Gyproc plasterboard lining
2 Gypframe GL8 Track 5 Gypframe GL11 GypLyner Anchor 8 Proprietary window unit 6
3 Gyproc Sealant 6 Wall structure 9 Moy Isover Insulation
(subject to requirements)
221
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 222
www.gypsum.ie
CLASSIC
GypLyner™
Junction details
GypWall™
22 External angle
222
May 2008
GypLyner UNIVERSAL (W)_120408:Layout 1 26/05/2008 15:31 Page 223
GypLyner™
6
223
May 2008