Professional Documents
Culture Documents
Fume Hood (United Version)
Fume Hood (United Version)
Fume Hood (United Version)
A-PR / VA / BY type
※ Product operation manual must be fully informed before the customer use.
※ Product Operation Manual must be fully informed before the customer use.
This operating manual of Fume hood is a precaution for safety to keep the appropriate usage and the user’s safety as well as the laboratory safety, and to prevent any loss of property etc.
FUME HOOD Product operation manual
A-PR / VA / BY type
03
Contents
1. Preparation section
1.1 Warning and caution for safety 06
1.2 Installation environment 12
1.3 Transportation 13
1.4 Product installation 14
2. Use section
2.1 Buttons and features of the controller 16
2.2 Use of Controller 19
2.3 Use of valve 22
3. Other sections
3.1 Cleaning and repair 24 3.5 Product warranty contents and scope 30
3.2 Checklist before claim report 25 3.6 Product warranty
3.3 Product dimension 27
3.4 Power distribution box power distribution 29
diagram
04
FUME HOOD
Product operation manual
Preparation section
1.1 Warning and caution for safety 06
1.2 Installation environment 12
1.3 Transportation 13
1.4 Product installation 14
Warning
If not observed, user may be injured.
Caution
If not observed, property loss may be caused.
This is a sign of compulsory order, which shows the items to be surely observed.
This is a sign of prohibition of an action, which stresses the items not to be done.
06
Preparation section Warning and caution for safety
Do not install near the heating equipment and the object sensible
to heat, moistly/oily/dusty place, where direct rays and water (rain It should be installed where the bottom is strong and horizontal.
water etc.) is reached, or where there is a possibility of gas leak.
▶ Unusual vibration, noise, and failure may be caused.
▶ There is a danger of electric shock, fire, failure, and explosion.
▶ A socket with earth must be used.
07
Preparation section Warning and caution for safety
Be sure to connect the power plug to the end of socket, and do Connect the power plug with its cord directed downward.
not use any damaged power plug, power cord, and loose socket.
▶ If connected in the opposite direction, lines may be cut at inside
▶ Electric shock or fire may be caused. of the cord, which may cause electric shock or fire.
Do not excessively bend, pull, twist or tie the power cord. And In case power cord or power plug is damaged, let them be
do not hang it up on the metal part, nor put heavy object on it, exchanged by the manufacturer or service agent or qualified
nor insert in between or into the backside of product. engineer in order to prevent any danger.
▶ Electric shock or fire may be caused.
08
Preparation section Warning and caution for safety
09
Preparation section Warning and caution for safety
150mm
or more
Wear the personal protective equipment In case equipment is stored, backside and floor
Do not use it with a head inside the hood.
before use. side should be spaced for a smooth air flow.
PERCHLORIC PERCHLORIC
ACID ACID
10
Preparation section Warning and caution for safety
◎ Additional cautions
[Other cautions]
▶ Use the fume hood after checking if it is normally operated or not ▶ Do not use the chemicals of which use is prohibited in the fume hood.
before test.
▶ Product performance test should be taken more than one time per
▶ Push and turn the handle of the locking device for the gas valve. one year.
(Test should be implemented by an expert in a proven method.)
▶ Do not evaporate any chemicals in the hood with disposal of
chemicals. ▶ All test materials and equipment should be put inside for use within
150mm from the door.
▶ In case test solution is spilt or poured, it should be cleaned
immediately. ▶ In case any accident is occurred, close the fume hood door in
use and contact an expert and a person in charge of equipment.
▶ In case any horizontal window is installed, use the horizontal
window with closed.(Do not open the horizontal window with the
door lifted up.)
▶ In case any chemicals are stored in the space of power distribution box,
there is a danger of explosion and fire.
11
Preparation section Installation environment
[Installation environment]
Installation environment conditions Safety measure
▶ Fume hood(A-PR/ A-VA/ A-BY) is designed in accordance with the ▶ Required conditions : It should be handled by an authorized personnel.
following conditions.
Should be used in clean room. Protection against water ① The product should be treated in
infiltration is not available.
accordance with the laws and
regulations for the human health and
safety of each countries.
12
Preparation section Transport method
▶ Please avoid the place where the sun is beating down, where there is much
heat, where it is severely cold.
- It the temperature of an installation place is too high or low, abnormality
of function may be caused.
13
Preparation section Product installation
[Product installation]
① Please install the product after being fully informed of the
cautions before the product installation.
⑤ Put the product on the installation place and connect the power
cord of the upper part.
Please push the power button after power is connected, and check if there is any abnormality with the blower operation.
14
FUME HOOD
Product operation manual
Use Section
2.1 Buttons and features of the controller 16
2.2 Use of Controller 19
2.3 Use of valve 22
Blower
Power <Setting>
Airflow Enter
check
Up Menu
<Move>
Down
<Move> Alarm off
Lamp Display
16
Use section Part Names and Functions
17
Use section Part Names and Functions
⑤ [Blower] ⑥ [Enter]
You can turn the ON / OFF. - You can choice the menu.
(When Using only the Blower)
<OFF> <ON>
⑧ [Alarm]
It can be On / Off when an alarm occurs.
⑦ [Menu]
You can launch the menu.
<OFF> <ON>
19
Use section Use the Controller
Air flow speed Inverter Air flow speed Blower Air flow speed Damper
range setting Control value range setting Control value range setting Control value
20
Use section
[ Error message]
※ Mounting a Air Flow Sensor
Screen Contents
Vel:Sensor Err 60Hz A warning sound and a message will occur when the
A:0.20-0.50m 40% air flow sensor is out of order.
22
FUME HOOD
Product operation manual
Other section
3.1 Cleaning and repair 24
3.2 Check list before claim report 25
3.3 Product dimension 27
3.4 Power distribution box power distribution 29
diagram
3.5 Product warranty contents and scope 30
3.6 Product warranty 32
1 2
Power should be disconnected from the Clean inside of work table with a sponge In case the fume hood should not be used inevitably for more than one month,
socket before cleaning. and soft cloth wet with neutral detergent. or should be kept in warehouse, the front door should be closed completely,
and should be sealed completely by use of vinyl.
3 4
Clean the outside surface, and remove Cleaning is completed. Please shut off the power of the product. Do not move, nor touch it while being
dusts etc. partially from the upper part and kept in a warehouse.
work table.
When the inside and outside of this product is cleaned, do not use brush, sponge, rough cloth etc. of which surface is rough.
Do not spray the product directly with water, nor clean it with Benzene, Thinner etc.
- Discoloration, Deformation, Damage, Electric Shock, Fire may be caused.
24
Other section Checklist before claim report
1-1. Isn't the voltage different? 1-1. This product is used only for 220V.
1-2. Isn't the power plug removed? 1-2. After checking the power plug, insert it again.
1-3. Isn't the circuit breaker away? 1-3. After checking the distribution box, operate it again.
2-1. Isn't the power plug removed? 2-1. After checking the power plug, insert it again.
2-2. Isn't the circuit breaker away? 2-2. After checking the distribution box, operate it again.
2-3. Isn't the life time of lamp expired? 2-3. Replace the lamp.
3-1. Isn't there any abnormality for the blower wiring? 3-1. Please check the condition of blower wiring.
3-2. Isn't the blower wiring out of order? 3-2. Please replace the blower wiring.
25
Other section Checklist before claim report
4-1. Isn't the life time of Lamp expired? 4-1. Please replace the lamp.
4-2. Isn't there any abnormality for the wiring? 4-2. Please check the condition of wiring.
Please refer to the above situations if any problem is occurred for the product.
If any problem is not solved with the solutions described as above, please contact CHCLAB Co., Ltd.
26
Other section Product demension
[TECHNICAL DATA]
A-PR / VA / BY A-PR / VA / BY
Dimension Dimension
1200 1500 1800 2100 2400 1200 1500 1800 2100 2400
Worktop Epoxy 25t (A-PR,A-VA)/ Ceramite 30t (A-BY) Electrical Box 220V Single phase
Vacuum,Air
Option
Valve ※ For more information, please visit www.chclab.com.
27
Other section Product demension
※ Product appearance, specification etc. may be changed without ※ Using Inconvenience and failure receive
prior notice for product improvement. TEL) +82-42-933-0036
FAX) +82-42-933-0039
※ Pictures, photos in the manual may not be matched up with
※ You can get fast service if you inform us correct Model No.,
the product.
Contact No. before you call us.
※ Please be careful not to lose the warranty in the operation manual. ※ Inter homepage
www.chclab.com
28
Other section Electric control box, electric diagram
[220V Single phase electric control box, electric diagram] Basic type
③ Terminal block
220V
110V
110V 220V
BLACK (S)
WHITE (W)
RED (R)
BLUE (B)
GREEN (G)
29
Other section Electric control box, electric diagram
① Circuit breaker
② AC electromagnetic switch
③ Overload relay
⑥ Terminal block
BLACK (S)
WHITE (W)
RED (R)
BLUE (B)
GREEN (G)
30
Other section 제품 보증 내용 및 보증 범위
▣ The warranty period of A-PR/ VA/ BY is 1 year after the first installation, and 1 year from the dispatch
date by CHC LAB Co., Ltd. Consumables and accessories are not included, and details are as follows.
If any problem is occurred, please contact the dealer (Purchase place) or CHC LAB.
31
Other section Product warranty
PRODUCT WARRANTY
1. CHC LAB Co., Ltd. enforces warranty for product based on the notification of the fair
trade commission as below
2. The warranty for quality of this product is received as per the contents written in the warranty.
3. Please call to the purchase place or +82-42-933-0036 if any failure occurred for the product.
※ In case product purchase date is not confirmed, the warranty period is dated from the
manufacture date or the date that has passed 3 months from the import customs
clearance date.
32
FUME HOOD
A-PR/ A-VA/ A-BY Product operation manual
Ver.01612
※ The Intellectual property right included in this operation manual (Contents, Image etc.) is owned by CHC LAB Co., Ltd., and any
unauthozized use without the consent of our company is prohibited.
※ The colors of the products included in this operation manual may be different with those of acual products, and the design
and performance may be changed without prior notice for the improvement of performance.