CONTROL UNIT

ENGINE-ECU

Engine-ECU is installed on the lower side of the right door front pillar. Engine-ECU
judges (calculates) the optimum control to deal with the constant minute changes in
driving conditions based on information input from the sensors and drives the
actuator. Engine-ECU is composed of 32-bit microprocessor and Random Access
Memory (RAM), Read Only Memory (ROM) and Input /Output interface. Engine-ECU
uses flash-memory ROM that allows re-writing of data so that change and correction
of control data is possible using special tools. It also uses Electrically Erasable
Programmable Read Only Memory (EEPROM) so that studied compensation data is
not deleted even if battery terminals are disconnected.

ENGINE-ECU CONNECTOR INPUT/OUTPUT PIN

ARRANGEMENT
Terminal Terminal Terminal name Terminal Terminal Terminal name
No. code No. code
1 ETV+ Throttle valve 2 ETV- Throttle valve
control servo (+) control servo (-)
3 OHFL Oxygen sensor 4 OHRL Oxygen sensor
(front) heater (rear) heater
5 SGT Crank angle sensor 6 SGC Camshaft position
sensor
7 ALTG Alternator G 8 CIL1 No. 1 ignition coil
terminal
9 INJ1 No. 1 injector 10 INJ2 No. 2 injector
11 PURG Purge control 12 OFLE Oxygen sensor
solenoid valve (front) offset voltage
13 O2FL Oxygen sensor 14 MAP Manifold absolute
(front) pressure sensor
15 5V Power supply 16 E Sensor earth
voltage applied to
manifold absolute
pressure sensor
17 TPSE Throttle position 18 DGND Sensor earth (digital
sensor earth signal)
19 TPS5 Power supply 20 K/S Detonation sensor
voltage applied to (+)
throttle position
sensor
21 ALTF Alternator FR 22 ALTL Alternator L
terminal terminal
23 CIL2 No. 2 ignition coil 24 INJ3 No. 3 injector
25 INJ4 No. 4 injector 26 ORLE Oxygen sensor
(rear) offset voltage
27 O2RL Oxygen sensor 28 WTS Engine coolant
(rear) temperature sensor
29 ATS Intake air 30 TPSM Throttle position
temperature sensor sensor (main)
31 TPSS Throttle position 33 K/SE Detonation sensor
sensor (sub) (-)
34 CIL4 No. 4 ignition coil 35 CIL3 No. 3 ignition coil
42 OPSW Engine oil pressure 48 C/RL Throttle valve
switch control servo relay
58 RSB Power supply 59 RSG Throttle valve
voltage applied to control servo earth
throttle valve
control servo
65 P/S Power steering fluid 72 FP/R Fuel pump relay
pressure switch
74 AC/T Fin thermo sensor 75 DIAG Diagnosis output
terminal
76 FMB Flash EP-ROM 77 BACK Backup power
data rewriting source
power source
80 V/S Vehicle speed 86 AFSE Air flow sensor
sensor earth
87 ACTE Fin thermo sensor 88 AC/S Blower switch
earth
89 IGN Ignition switch-IG 95 AFS Air flow sensor
96 AFS5 Power supply 97 ST Ignition switch-ST
voltage applied to
Air flow sensor (5V)
98 STCD Starter active signal 101 CANH CAN interface
(high)
102 CANL CAN interface (low) 103 STRL Starter relay
104 AC/R A/C compressor 106 BAT1 Power source
relay
108 F/LO A/C condenser fan 110 C/R Engine control relay
relay
111 APSM Accelerator pedal 112 APS5 Power supply
position sensor voltage applied to
(main) accelerator pedal
position sensor
(main)
113 APSE Accelerator pedal 119 GNDB Engine-ECU earth
position sensor
(main) earth
120 GNDE Engine-ECU earth 123 APSS Accelerator pedal
position sensor
(sub)
124 AP5 Power supply 125 APE Accelerator pedal
voltage applied to position sensor
accelerator pedal (sub) earth
position sensor
(sub)

MMC-Manuals.ru