Professional Documents
Culture Documents
28mm Scifi Main Battle Tank - Instruction Booklet
28mm Scifi Main Battle Tank - Instruction Booklet
28mm Scifi Main Battle Tank - Instruction Booklet
POSSIBLE CONFIGURATIONS
WWW.DARKAGEDESIGN.CO.UK
WWW.FACEBOOK.COM/DARKAGEDESIGN
WWW.INSTAGRAM.COM/DARKAGEDESIGN
1. Getting Started
2. Central Core
3. Tracked Vehicle
4. Antigravity Vehicle
5. Top Turret Weapon
6. No Turret Weapon
7. Front Turret
8. Side Weapon Pods
9. Side Sponsons
10. Pintle Weapon
11. Auxiliary Weapons
These instructions will guide you through the assembly of the 28mm Scifi Main Battle
Tank.
This is a larger and more complicated kit, with multiple options for assembly and
construction. It is recommended that you read through all the steps in advance before
committing to assembly.
We recommend a Gel Cyanoacrylate (Super Glue) for assembly of resin printed parts,
although some larger assemblies may benefit from Epoxy or other types of adhesive.
Always “dry-fit” pieces before assembly to ensure correct fitment and alignment.
If you have any questions about the assembly process feel free to reach out to us via
Social Media or via email (alex@darkagedesign.co.uk)
To assemble the Central Core you will need to print the following pieces in the “MBT -
Generic Parts” folder:
(L) Assault Ramp Hinge.stl
(L) Front Arch.stl
(R) Assault Ramp Hingestl
(R) Front Arch.stl
2 x Exhaust Block.stl
2 x Mid Arch.stl
2 x Rear Arch.stl
Assault Ramp.stl
Front Turret Cover.stl (Retain this for a later step)
Main Body Shell (Middle - Front).stl
Main Body Shell (Middle - Rear Wall).stl
Main Body Shell (Middle - Rear).stl
If you don’t wish to print / show the interior of the vehicle you can skip printing the pieces
shown in Italics.
Locate the Main Body Shell (Middle—Rear Wall) into the Main Body Shell (Middle—Rear).
Align the shape of the bottom of the wall with the cutout pattern on the interior floor. The
wall should align flush with the angled edges of the half arch detail and the two cutouts.
Locate the Rear Arch into the Main Body Shell (Middle—Rear). Align the back of the Rear
Arch with the space between the raised arch details.
Locate the Mid Arch into the Main Body Shell (Middle—Front). Align the back of the Mid
Arch with the space between the raised arch details.
NOTE: If you want to paint the interior of the vehicle it is recommended that you do it at
this point in the construction—as access will significantly more restricted afterwards!
Glue the completed Main Body Shell (Middle—Front) and Main Body Shell (Middle—Rear)
together, aligning the pieces ensuring the sides are flush and the arches interlock cleanly.
NOTE: If you don’t want to see the interior you can just glue the Assault Ramp into the
Main Body assembly
Locate the Assault Ramp with the hinge pins in the Main Body assembly. Carefully apply
glue to the bottom of the (L) & (R) Assault Ramp Hinge pieces and use them to capture
the hinge pins in place.
Locate the 2 x Exhaust Block into the locating holes on the Main Body assembly.
The Central Core assembly is complete.
Now choose if you wish your Main Battle Tank to be motive via Tracks or Antigravity and
follow the appropriate steps in the following sections.
To assemble the Tracked Version you will need to print the following pieces in the “MBT -
Tracked Parts” folder:
Main Body Shell (Left Side - Front).stl
Main Body Shell (Left Side - Rear).stl
Main Body Shell (Right Side - Front).stl
Main Body Shell (Right Side - Rear).stl
Side Skirt (Left).stl
Side Skirt (Right).stl
Tracks (Front Left).stl
Tracks (Front Right).stl
Tracks (Rear Left).stl
Tracks (Rear Right).stl
Attach the Main Body Shell (Left Side—Front) to the Main Body Shell (Left Side—Rear).
Align the back of the track sections on a flat surface to ensure they are flush.
The sides of the Track Assemblies and Central Core are keyed in various ways to ensure a
proper alignment.
The Tracked Vehicle assembly is complete.
Now choose how you wish your Main Battle Tank to be armed and follow the appropriate
steps in the following sections.
To assemble the Antigravity Version you will need to print the following pieces in the
“MBT - Antigrav Parts” folder:
(L) Front Gravplate.stl
(L) Grav Main Body Shell (Side - Front).stl
(L) Grav Main Body Shell (Side - Rear).stl
(L) Lower Engine.stl
(L) Rear Engine Shroud.stl
(L) Rear Gravplate.stl
(L) Upper Engine.stl
(R) Front Gravplate.stl
(R) Grav Main Body Shell (Side - Front).stl
(R) Grav Main Body Shell (Side - Rear).stl
(R) Lower Engine.stl
(R) Rear Engine Shroud.stl
(R) Rear Gravplate.stl
(R) Upper Engine.stl
Gravplate Front x 8.stl
Gravplate Rear x 4.stl
Attach the (L) Grav Main Body Shell (Side—Front) to the (L) Grav Main Body Shell (Side—
Rear)
Align the back of the sections on a flat surface to ensure they are flush.
The sides of the Antigravity Assemblies and Central Core are keyed in various ways to en-
sure a proper alignment.
Attach the (L) Rear Gravplate to the assembly from the previous step.
Attach the (R) Rear Gravplate to the assembly from the previous step.
The Antigravity Vehicle assembly is complete.
Now choose how you wish your Main Battle Tank to be armed and follow the appropriate
steps in the following sections.
To assemble the MBT without a turret you will need to print the following pieces in the
“Weapons—Top Turret” folder:
All versions:
Main Body Shell Turret (Middle - Roof).stl
(L) Scifi Knight Arm.stl
(R) Scifi Knight Arm.stl
Scifi Knight Helmet.stl
Scifi Knight Torso.stl
Turret Ring and Arm (Top Turret).stl
One of the below, depending on if you want a rear facing Point Defence weapon:
Turret Centre.stl
Turret Centre (Point Defence).stl
Assemble the various Scifi Knight components into the Turret Ring and Arm (Top Turret).
NOTE: You may wish to leave affixing the Arms until you have positioned the Pintle
Weapon of your choice.
If you are using the Turret Centre (Point Defence) then you can insert your chosen Point
Defence weapon (Ground to Air Missile Pod or Point Defence Stubber).
Locate the Turret into the Main Body assembly from the previous section.
(Antigravity version shown here for reference, weapons are compatible with both).
The Top Turret Weapon assembly is complete.
(Antigravity version shown here for reference, weapons are compatible with both).
To assemble the MBT without a turret you will need to print the following pieces in the
“Weapons—No Turret” folder:
(L) Scifi Knight Arm.stl
(R) Scifi Knight Arm.stl
Driver Viewport.stl
Main Body Shell (Middle - Roof).stl
Scifi Knight Helmet.stl
Scifi Knight Torso.stl
Turret Ring and Arm.stl
Locate the Main Body Shell (Middle—Roof) into the Main Body assembly from the
previous section.
(Tracked version shown here for reference, weapons are compatible with both).
Locate the Driver Viewport into the Main Body assembly from the previous section.
Locate the Turret Ring and Arm into the Main Body assembly from the previous section.
(Tracked version shown here for reference, weapons are compatible with both).
Assemble the various Scifi Knight components into the Turret Ring and Arm.
NOTE: You may wish to leave affixing the Arms until you have positioned the Pintle
Weapon of your choice.
To assemble the Front Turret you will need to print one of the following pieces in the
“Weapons—Front Turret” folder:
Dual Chaingun.stl
Dual Gatling Cannon.stl
Dual Heavy Rifle.stl
Dual Laser Cannon.stl
NOTE: You will also need the Front Turret Cover component that you printed as part of the
Central Core.
Dual Heavy Rifle
Dual Chaingun
Locate the Front Turret weapon of your choice (Dual Chaingun, Dual Gatling Cannon, Dual
Heavy Rifle or Dual Laser Cannon) into the retaining hole in the Main Body assembly
(Tracked version shown here for reference, weapons are compatible with both).
Use the Front Turret Cover to hold the weapon in place, if no glue is placed onto the
weapon spindle it will be able to pivot in place.
The Front Turret assembly is complete (Example shows Dual Chaingun option).
To assemble the MBT with Side Weapon Pods you will need to print the following files
from the “Weapons—Side Launchers” folder:
Flamethrower Sponsons:
(L) Flamethrower Sponson Base.stl
(R) Flamethrower Sponson Base.stl
Flamethrower Barrel (Long) x 2.stl
Flamethrower Barrel (Short) x 2.stl
Sponson - Top Mount x 2.stl
Sponson - Lower Mount x 2.stl
Lasercannon Sponson
Flamethrower Sponson
Pintle Gatling
Locate your Pintle Weapon of choice onto the retaining notches on the Turret Ring and
Arm assembly.
To assemble the MBT with Auxiliary Weapons you will need to print your choice of the
following files from the “Weapons—Auxiliary” folder:
Fragmentation Launcher (Closed).stl
Fragmentation Launcher (Open).stl
Seeking Missile Pod (Closed).stl
Seeking Missile Pod (Open - Empty).stl
Seeking Missile Pod (Open - Loaded).stl
Seeking Missile.stl
Fragmentation Launcher
(Closed)
Fragmentation Launcher
(Open)
Locate your Auxiliary Weapons of choice onto the Main Body assembly.
Seeking Missile
Pod (Open—
Empty) & Seeking
Missile
Seeking Missile
Pod (Open—
Loaded)
Seeking Missile
Pod (Closed)
Locate your Auxiliary Weapons of choice onto the Main Body assembly.
If you have any problems with assembly please message us via our Website, Instagram
or Facebook using the details provided on the front page of this guide.