Report Gunung Walat

LAPORAN ANALISIS STRUKTUR
CAFE DAN RESTORAN GUNUNG WALAT

Kab.Sukabumi
10/10/2022
Daftar Tabel
1. Structure Data 6
1.1 Story Data 6

1.2 Grid Data 6
1.3 Point Coordinates 6
1.4 Line Connectivity 8
1.5 Area Connectivity 12
1.6 Mass 14
1.7 Groups 14
2. Properties 15
2.1 Materials 15
2.2 Frame Sections 15
2.3 Shell Sections 15
2.4 Reinforcement Sizes 16
2.5 Links 16
2.6 Tendon Sections 16
3. Assignments 17
3.1 Joint Assignments 17

3.2 Frame Assignments 20
3.3 Shell Assignments 26
4. Loads 28
4.1 Load Patterns 28

4.2 Load Sets 28
4.3 Auto Seismic Loading 28
4.4 Applied Loads 31
4.4.1 Line Loads 31
4.4.2 Area Loads 34
4.5 Functions 36
4.5.1 Response Spectrum Functions 36
4.5.2 Time History Functions 37
4.6 Load Cases 37
4.7 Load Combinations 37
5. Analysis Results 38
5.1 Structure Results 38

5.2 Story Results 38
5.3 Point Results 39
5.4 Modal Results 50
Daftar
Table 1.1 Story Definitions 6
Table 1.2 Grid Definitions - General 6
Table 1.3 Grid Definitions - Grid Lines 6
Table 1.4 Point Bays 6
Table 1.5 Column Bays 8
Table 1.6 Beam Bays 9
Table 1.7 Brace Bays 11
Table 1.8 Floor Bays 12
Table 1.9 Mass Source Definition 14
Table 1.10 Mass Summary by Story 14
Table 1.11 Mass Summary by Group 14
Table 1.12 Group Definitions 14
Table 2.1 Material Properties - General 15
Table 2.2 Frame Section Property Definitions - Summary 15
Table 2.3 Area Section Property Definitions - Summary 15
Table 2.4 Reinforcing Bar Sizes 16
Table 2.5 Link Property Definitions - Summary 16
Table 2.6 Tendon Section Properties 16
Table 3.1 Joint Assignments - Summary 17
Table 3.2 Frame Assignments - Summary 20
Table 3.3 Area Assignments - Summary 26
Table 4.1 Load Pattern Definitions 28
Table 4.2 Shell Uniform Load Sets 28
Table 4.5 Frame Loads Assignments - Distributed 31
Table 4.6 Area Load Assignments - Uniform 34
Table 4.7 Area Load Assignments - Uniform Load Sets 36
Table 4.8 Functions - Response Spectrum - User Defined 37
Table 4.9 Functions - Time History - User Defined 37
Table 4.10 Load Case Definitions - Summary 37
Table 4.11 Load Combination Definitions 37
Table 5.1 Base Reactions 38
Table 5.2 Story Drifts 38
Table 5.3 Story Forces 39
Table 5.4 Joint Reactions 39
Table 5.5 Modal Periods And Frequencies 50
Table 5.6 Modal Participating Mass Ratios 50
Table 5.7 Modal Load Participation Ratios 51
Table 5.8 Modal Direction Factors 51
Structure 10/10/20
1 Structure Data
This chapter provides model geometry information, including items such as story levels, point coordinates, and element
connectivity.
1.1 Story Data

Table 1.1 - Story Definitions
Height Master Splice
Tower Name Similar To Color
m Story Story
T1 Atap 2.5 No None No Red
T1 Ringbalk 3 No None No Red
T1 Lantai 3 1.5 No None No Red
T1 ++ 1.5 No None No Red
T1 Lantai 2 1.5 No None No Magenta
T1 + 1.5 No None No Yellow
1.2 Grid Data
Table 1.2 - Grid Definitions - General

Bubble
Ux Uy Rz Story
Tower Name Type Size Color
m m deg Range
mm
T1 G1 Cartesian 0 0 0 Default 1250 Gray6
Table 1.3 - Grid Definitions - Grid Lines

Grid Line Ordinate Bubble Location
Name End Visible
Type m
X 0
G1 (Cartesian) X Yes
(Cartesian) X
G1 (Cartesian) X 3.5 End Yes
(Cartesian) X
G1 (Cartesian) Y 6.5 End Yes
(Cartesian) Y
(Cartesian) Y
(Cartesian) Y
(Cartesian)
G1 0 Start Yes
G1 3.5 Start Yes
G1 7 Start Yes
G1 11 Start Yes
G1 15 Start Yes
G1 17 Start Yes
Y
G1 23 Start Yes
(Cartesian)
Y
G1 27 Start Yes
(Cartesian)
Page 4 of 50
Structure 10/10/20
1.3 Point Coordinates

Table 1.4 - Point Bays
LabelIs Auto Point X Y DZBelow m
m m
22 No 3.5 19 0
23No6.5190
24 No 9.5 19 0
34 No 0 7 0
25 No 13.5 19 0
42 No 8.5 7 0.1685
43 No 8.5 11 0.1685
44 No 8.5 15 0.1685
45 No 8.5 19 0.1685
47 No 4.3333 4.0833 2.1114
48 No 3.5 0 0
49 No 3.5 3.5 0
50 No 3.5 7 0
51 No 3.5 11 0
52 No 3.5 15 0
53 No 3.5 17 0
54 No 6.5 0 0
55 No 6.5 3.5 0
56 No 6.5 7 0
57 No 6.5 11 0
58 No 6.5 15 0
59 No 6.5 17 0
60 No 9.5 0 0
61 No 9.5 3.5 0
62 No 9.5 7 0
63 No 9.5 11 0
64 No 9.5 15 0
65 No 9.5 17 0
66 No 13.5 0 0
67 No 13.5 3.5 0
68 No 13.5 7 0
69 No 13.5 11 0
70 No 13.5 15 0
71 No 13.5 17 0
72 No 3.5 23 0
73 No 6.5 23 0
74 No 9.5 23 0
75 No 13.5 23 0
76 No 13.5 27 0
77 No 9.5 27 0
78 No 5.1667 4.6667 1.7228
79 No 6 5.25 1.3342
80 No 6.8333 5.8333 0.9456
81 No 7.6667 6.4167 0.5571
82 No 12.6667 4.0833 2.1114
83 No 11.8333 4.6667 1.7228
84 No 11 5.25 1.3342
85 No 10.1667 5.8333 0.9456
86 No 9.3333 6.4167 0.5571
87 No 4.3333 22.3333 2.1114
88 No 5.1667 21.6667 1.7228
89 No 6 21 1.3342
90 No 6.8333 20.3333 0.9456
91 No 7.6667 19.6667 0.5571
92 No 12.6667 22.3333 2.1114
93 No 11.8333 21.6667 1.7228
Page 5 of 50
Structure 10/10/20
Is Auto X Y DZBelow
Label
Point m m m
94 No 11 21 1.3342
95 No 10.1667 20.3333 0.9456
96 No 9.3333 19.6667 0.5571
135 No 0 3.5 0
1.4 Line Connectivity
Table 1.5 - Column Bays

Label PointBayI PointBayJ IEndStory
C1 135 135 Same
C2 34 34 Same
C3 22 22 Below
C4 23 23 Below
C5 24 24 Below
C6 25 25 Below
C14 48 48 Same
C15 49 49 Same
C16 50 50 Same
C19 51 51 Same
C20 52 52 Same
C21 53 53 Same
C22 54 54 Same
C23 55 55 Same
C25 56 56 Same
C26 57 57 Same
C27 58 58 Same
C34 59 59 Same
C35 60 60 Same
C36 61 61 Same
C37 62 62 Same
C38 63 63 Same
C41 64 64 Same
C42 65 65 Same
C43 66 66 Same
C44 67 67 Same
C45 68 68 Same
C46 69 69 Same
C47 70 70 Same
C48 71 71 Same
C49 72 72 Same
C50 73 73 Same
C51 74 74 Same
C52 75 75 Same
C53 76 76 Same
C54 77 77 Same
C56 49 49 Below
C57 50 50 Below
C58 51 51 Below
C59 52 52 Below
C61 55 55 Below
C62 56 56 Below
C63 57 57 Below
C64 58 58 Below
C66 61 61 Below
C67 62 62 Below
C69 63 63 Below
C70 64 64 Below
C74 67 67 Below
Page 6 of 50
Structure 10/10/20

C75 68 68 Below
C90 69 69 Below
C91 70 70 Below
C107 72 72 Below
C108 73 73 Below
C109 74 74 Below
C110 75 75 Below
C111 76 76 Below
C112 77 77 Below
Table 1.6 - Beam Bays

Label PointBayI PointBayJ
B19 22 23
B20 23 24
B21 24 25
B26 52 22
B27 64 24
B28 70 25
B29 25 75
B30 22 72
B31 23 73
B32 24 74
B33 58 23
B34 42 45
B35 80 90
B36 79 89
B37 78 88
B38 47 87
B39 83 93
B40 84 94
B41 82 92
B42 85 95
B43 86 96
B44 50 56
B45 56 62
B46 62 68
B47 49 55
B48 55 61
B49 61 67
B50 48 54
B51 54 60
B52 60 66
B53 81 91
B54 81 86
B55 49 50
B56 48 49
B57 55 56
B58 54 55
B59 61 62
B60 60 61
B61 67 68
B62 66 67
B63 53 59
B64 59 65
B65 65 71
B66 52 58
B67 58 64
B68 64 70
B69 51 57
Page 7 of 50
Structure 10/10/20
Label PointBayI PointBayJ

B70 57 63
B71 63 69
B72 52 53
B73 51 52
B74 50 51
B75 58 59
B76 57 58
B77 56 57
B78 64 65
B79 63 64
B80 62 63
B81 70 71
B82 69 70
B83 68 69
B84 72 73
B85 53 72
B86 73 74
B87 59 73
B88 65 74
B89 74 75
B90 77 76
B91 74 77
B92 75 76
B93 71 75
B94 34 50
B95 135 49
B96 80 85
B97 79 84
B98 78 83
B99 47 82
B100 87 92
B101 88 93
B102 89 94
B103 90 95
B104 91 96
B139 135 34
Table 1.7 - Brace Bays

D21 50 42 Below
D22 68 42 Below
D23 51 43 Below
D24 69 43 Below
D25 52 44 Below
D26 70 44 Below
D27 22 45 Below
D28 25 45 Below
D35 49 47 Below
D36 47 78 Same
D37 78 79 Same
D38 79 80 Same
D39 80 81 Same
D40 81 42 Same
D41 67 82 Below
D42 82 83 Same
D43 83 84 Same
D44 84 85 Same
D45 85 86 Same
D46 86 42 Same
Page 8 of 50
Structure 10/10/20

D47 72 87 Below
D48 87 88 Same
D49 88 89 Same
D50 89 90 Same
D51 90 91 Same
D52 91 45 Same
D53 75 92 Below
D54 92 93 Same
D55 93 94 Same
D56 94 95 Same
D57 95 96 Same
D58 96 45 Same
1.5 Area Connectivity
Table 1.8 - Floor Bays

NumPoint PointNum PointBay
Label
s ber
F1 4 1 135
F1249
F1 3 50
F1 4 34
F5 4 1 48
F5 2 54
F5 3 55
F5 4 49
F6 4 1 54
F6 2 60
F6 3 61
F6 4 55
F7 4 1 60
F7 2 66
F7 3 67
F7 4 61
F8 4 1 49
F8 2 55
F8 3 56
F8 4 50
F9 4 1 55
F9 2 61
F9 3 62
F9 4 56
F10 4 1 61
F10 2 67
F10 3 68
F10 4 62
F11 4 1 50
F11 2 56
F11 3 57
F11 4 51
F12 4 1 56
F12 2 62
F12 3 63
F12 4 57
F16 4 1 62
F16 2 68
F16 3 69
F16 4 63
F17 4 1 51
Page 9 of 50
Structure 10/10/20
NumPoint PointNum
Label PointBay
s ber
F17 2 57
F17 3 58
F17 4 52
F21 4 1 57
F21 2 63
F21 3 64
F21 4 58
F22 4 1 63
F22 2 69
F22 3 70
F22 4 64
F23 4 1 52
F23 2 58
F23 3 59
F23 4 53
F24 4 1 58
F24 2 64
F24 3 65
F24 4 59
F25 4 1 64
F25 2 70
F25 3 71
F25 4 65
F26 4 1 65
F26 2 71
F26 3 75
F26 4 74
F27 4 1 59
F27 2 65
F27 3 74
F27 4 73
F28 4 1 53
F28 2 59
F28 3 73
F28 4 72
F29 4 1 74
F29 2 75
F29 3 76
F29 4 77
1.6 Mass
Table 1.9 - Mass Source Definition
Include NameIs DefaultLateral Include Vertical Mass? Source Added
SourceMove
Mass?
LumpSource Mass?Self Mass? Load Pattern
Mass? LoadMass Multiplier
Patterns? Centroid?
MsSrc1 Yes Yes No Yes No No Yes No DL 1
MsSrc1 SIDL 1
MsSrc1 LL 0.25
Page 10 of
Structure 10/10/20
Table 1.10 - Mass Summary by Story

UX UY UZ
Story
kg kg kg
Atap 2804.74 2804.74 0
Ringbalk 77775.05 77775.05 0
Lantai 3 324129.39 324129.39 0
++ 0 0 0
Lantai 2 242095.71 242095.71 0
+ 0 0 0
Lantai 1 55857.81 55857.81 0
Table 1.11 - Mass Summary by Group

Self
Self Mass Mass X Mass Y Mass Z
Group Weight
kg kg kg kg
kN
All 0 2221.6013 702662.69 702662.69 0
1.7 Groups
Table 1.12 - Group Definitions

Steel Concrete Composit
Name Color
Design? Design? e Design?
All Yellow No No No
Page 11 of
Properti 10/10/20
2 Properties
This chapter provides property information for materials, frame sections, shell sections, and links.
2.1 Materials
Table 2.1 - Material Properties - General
Material Type SymType Grade Color Notes
4000Psi Concrete Isotropic f'c 4000 psi Gray8Dark
A416Gr270 Tendon Uniaxial Grade 270 Green
A615Gr60 Rebar Uniaxial Grade 60 Blue
2.2 Frame Sections
Page 12 of
Properti
BJ37 Steel Isotropic Grade 50 Yellow
10/10/20
K300 Concrete Isotropic 25 Mpa Green
Table 2.2 - Frame Section Property Definitions - Summary (Part 1 of 3)

Area J I33 I22 As2 As3S33Pos S33Neg
Name MaterialShape Color
cm2 cm4 cm4 cm4 cm2 cm2 cm3 cm3
Balok B5 WF
300.150.6,5.9 Steel I/Wide
Flange 45.3 10 6932.5 506.9 19.4 25.4 462.2 462.2
BJ37 8454016
Balok B6 WF
250.125.6.9 Steel I/Wide
Flange 36.4 7.8 3892.9 293.4 14.8 21.4 311.4 311.4
BJ37 4227327
Cold Formed
C 150.50.20.2,5 BJ37 C Red 6.9 0.1 232.3 24.1 3.6 2.3 31 31
Kolom WF
300.150.6,5.9 Steel I/Wide
Flange 45.3 10 6932.5 506.9 19.4 25.4 462.2 462.2
BJ37 Magenta

S22Pos S22Neg Z33 Z22 R33 R22 CG CG PNA PNA SC SC
Cw
Offset 3 Offset 2 Offset 3 Offset 2 Offset 3 Offset 2
cm3 cm3 cm3 cm3 mm mm cm6 mm mm mm mm mm mm
67.6 67.6 522.1 104.2 123.7 33.4 107174.4 0 0 0 0
46.9 46.9 351.9 72.4 103.4 28.4 42539.8 0 0 0 0
15.5 7 37.8 10.7 57.9 19.1 1181.8 9.4 0 22.6 0 46.9 0
67.6 67.6 522.1 104.2 123.7 33.4 107174.4 0 0 0 0

Area As2 As3 I33 I22 Mass Weight
J Modifier Modifier
Modifier Modifier Modifier Modifier Modifier Modifier
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
2.3 Shell Sections
Table 2.3 - Area Section Property Definitions - Summary

Total Deck Depth mm
Element Type Deck
Name Type Material Thickness Material
mm
Deck20 Deck Membrane K300 200 BJ37 42
Plank1 Slab Membrane 4000Psi 200
Plat Tangga Slab Shell-Thin K300 200
Slab1 Slab Shell-Thin 4000Psi 200
Wall1 Wall Shell-Thin 4000Psi 250
Page 13 of
Properti 10/10/20
2.4 Reinforcement Sizes
Table 2.4 - Reinforcing Bar Sizes

Diameter Area
Name
mm cm2
6 6 0.3
8 8 0.5
10 10 0.8
12 12 1.1
14 14 1.5
16 16 2
18 18 2.5
20 20 3.1
22 22 3.8
25 25 4.9
26 26 5.3
28 28 6.2
32 32 8
36 36 10.2
40 40 12.6
50 50 19.6
2.5 Links
Table 2.5 - Link Property Definitions - Summary

Degrees Defined Defined
Mass Weight
Name Type of Length Area
kg kN
Freedom m m2
Link1 Linear U1 0 0 1 1
2.6 Tendon Sections
Table 2.6 - Tendon Section Properties

StrandAre
Name Material a Color Notes
cm2
Tendon1 A416Gr270 1 Red
Page 14 of
Assignmen 10/10/20
3 Assignments
This chapter provides a listing of the assignments applied to the model.
3.1 Joint Assignments

Table 3.1 - Joint Assignments - Summary
UniqueNa Diaphrag
Story Label Restraints
me m
Atap 42 306From Area
Atap43307From Area
Atap 44 308 From Area
Ringbalk 49 100 From Area
Lantai 3 49 92 From Area
Page 15 of
Assignmen 10/10/20
UniqueNa Diaphrag
me m
Lantai 35295From Area
UX; UY; UZ; RX;
RY; RZ
Lantai 3 58 114From Area
From Area UX; UY; UZ; RX;
Lantai 3 59 115
RY; RZ
UX; UY; UZ; RX;
Lantai 3 64 126 From Area RY; RZ
Lantai 3 71 139
RY; RZ
Lantai 3 72 147
RY; RZ
Lantai 3 73 149
RY; RZ
Lantai 3 74 151
RY; RZ
Lantai 3 75 153
RY; RZ
Lantai 3 76 155
RY; RZ
Lantai 3 77 157
RY; RZ

Lantai 2 53 18 From Area UX; UY;
Lantai 2 49 10 RY;UZ;
RZ RX;
RY; RZ
Lantai 2 59 66
RY; RZ
Lantai 2 65 78
RY; RZ
Page 16 of
Assignmen 10/10/20
UniqueNa Diaphrag
me m
Lantai 2 71 90
RY; RZ
Lantai 1 34 166
RY; RZ
Lantai 1 135 165
RY; RZ
Lantai 1 48 7
RY; RZ
Lantai 1 49 9
RY; RZ
Lantai 1 50 11
RY; RZ
Lantai 1 51 13
RY; RZ
Lantai 1 52 15
RY; RZ
Lantai 1 53 17
RY; RZ
Lantai 1 54 55
RY; RZ
Lantai 1 55 57
RY; RZ
Lantai 1 56 59
RY; RZ
Lantai 1 57 61
RY; RZ
Lantai 1 58 63
RY; RZ
Lantai 1 59 65
RY; RZ
Lantai 1 60 67
RY; RZ
Lantai 1 61 69
RY; RZ
Lantai 1 62 71
RY; RZ
Lantai 1 63 73
RY; RZ
Lantai 1 64 75
RY; RZ
Lantai 1 65 77
RY; RZ
Lantai 1 66 79
RY; RZ
Lantai 1 67 81
RY; RZ
Lantai 1 68 83
RY; RZ
Lantai 1 69 85
RY; RZ
Lantai 1 70 87
RY; RZ
Lantai 1 71 89
RY; RZ
Lantai 1 72 105From AreaUX; UY; UZ
Lantai 173107From AreaUX; UY; UZ
Lantai 1 74 109 From Area UX; UY; UZ
Page 17 of
Assignmen 10/10/20
3.2 Frame Assignments

Table 3.2 - Frame Assignments - Summary
Max Station Spacing m
Min Number Stations
UniqueNa Design Length m Analysis
Story Label
meType SectionDesign Section
Balok B6 WF
Atap B34 359 Beam 12 Balok B6 WF
250.125.6.9 0.5
250.125.6.9
Atap B35 384 Beam 14.5 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B36 385 Beam 15.75 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B37 386 Beam 17 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B38 387 Beam 18.25 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B39 388 Beam 17 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B40 389 Beam 15.75 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B41 390 Beam 18.25 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B42 391 Beam 14.5 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B43 392 Beam 13.25 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B53 393 Beam 13.25 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B54 394 Beam 1.6667 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B96 395 Beam 3.3333 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B97 396 Beam 5 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B98 397 Beam 6.6667 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B99 398 Beam 8.3333 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B100 399 Beam 8.3333 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B101 400 Beam 6.6667 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B102 401 Beam 5 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B103 402 Beam 3.3333 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Atap B104 403 Beam 1.6667 C 150.50.20.2,5 C 150.50.20.2,5 0.5
Balok B6 WF Balok B6 WF
Atap D21 345 Brace 5.5169 250.125.6.9 250.125.6.9 3
3
Atap D22 346 Brace 5.5169 250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9 3
Atap D23 347 Brace 5.5169
3
Atap D24 348 Brace 5.5169 250.125.6.9 250.125.6.9
250.125.6.9 3
Atap D25 349 Brace 5.5169 250.125.6.9
Balok B6 WF
Balok B6 WF 3
250.125.6.9 250.125.6.9
250.125.6.9 3
Atap D27 351 Brace 5.5169 250.125.6.9
Balok B6 WF
Balok B6 WF 3
250.125.6.9
Atap D28 352 Brace 5.5169 250.125.6.9
Balok B6 WF
Balok B6 WF 3
250.125.6.9
Atap D35 360 Brace 1.0889 250.125.6.9
Balok B6 WF
Balok B6 WF 3
250.125.6.9
Atap D36 361 Brace 1.0889 250.125.6.9
Balok B6 WF
Balok B6 WF 3
250.125.6.9 250.125.6.9
Atap D37 362 Brace 1.0889 Balok B6 WF
Balok B6 WF 3
250.125.6.9 250.125.6.9
250.125.6.9 3
Atap D39 364 Brace 1.0889 250.125.6.9 Balok B6 WF
Balok B6 WF 3
250.125.6.9
250.125.6.9
Atap D40 365 Brace 1.0889 Balok B6 WF
Balok B6 WF 3
250.125.6.9
250.125.6.9 Balok B6 WF
Atap D41 366 Brace 1.0889 3
Balok B6 WF 250.125.6.9
250.125.6.9 Balok B6 WF
Atap D42 367 Brace 1.0889 3
Balok B6 WF
250.125.6.9
250.125.6.9 Balok B6 WF
Atap D43 368 Brace 1.0889 3
Balok B6 WF
250.125.6.9
250.125.6.9
Atap D45 370 Brace 1.0889 3
250.125.6.9 250.125.6.9
Atap D46 371 Brace 1.0889 3
250.125.6.9 250.125.6.9
Page 18 of
Assignmen 10/10/20
Max
Min
UniqueNa Design Length Analysis Station
Story Label Design Section Number
me Type m Section Spacing
Stations
m
Atap D47 372 Brace 1.1357 3
250.125.6.9 250.125.6.9
Balok B6 WF 250.125.6.9
Atap D48
Balok B6 WF 250.125.6.9 373 Brace Balok B6 WF 3
1.1357 250.125.6.9
Balok B6 WF 250.125.6.9
Balok B6 WF
Atap 250.125.6.9
D49 374 Brace Balok B6 WF 3
1.1357 250.125.6.9
Balok B6 WF 250.125.6.9
Balok B6 WF
Atap 250.125.6.9
D50 375 Brace Balok B6 WF
1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Balok B6 WF 250.125.6.9 Balok B6 WF
Atap D51 376 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Atap D52 377 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Atap D53
Balok B6 WF 250.125.6.9 378 Brace 1.1357 250.125.6.9 3
Atap D54
Balok B6 WF 250.125.6.9 379 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Balok B6 WF
Atap D55
Balok B6 WF 250.125.6.9 380 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Atap D56 381 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Atap D57 382 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Atap D58 383 Brace 1.1357 250.125.6.9 3
Balok B6 WF 250.125.6.9
Ringbalk B44 223 Beam 3 250.125.6.9 0.5
Balok B6 WF 250.125.6.9
Ringbalk B45
Balok B6 WF 250.125.6.9 224 Beam 3 250.125.6.9 0.5
Balok B6 WF 250.125.6.9
Ringbalk B46 225 Beam Balok B6 WF
Balok B6 WF 250.125.6.9 4 250.125.6.9 0.5
Balok B6 WF 250.125.6.9
Balok B6 WF
Ringbalk 250.125.6.9
B47 226 Beam Balok B6 WF
3 250.125.6.9 0.5
Balok B6 WF 250.125.6.9
Balok B6 WF
Ringbalk 250.125.6.9
B48 227 Beam Balok B6 WF
3 250.125.6.9 0.5

4 250.125.6.9 0.5

3.5 250.125.6.9 0.5

3.5 250.125.6.9 0.5

3.5 250.125.6.9 0.5

3.5 250.125.6.9 0.5

3 250.125.6.9 0.5

3 250.125.6.9 0.5

4 250.125.6.9 0.5

3 250.125.6.9 0.5

3 250.125.6.9 0.5

4 250.125.6.9 0.5

4 250.125.6.9 0.5

4 250.125.6.9 0.5

4 250.125.6.9 0.5

4 250.125.6.9 0.5

4 250.125.6.9 0.5
Balok B6 WF
Ringbalk B80 235 Beam 4 250.125.6.9 0.5
Balok B6 WF
Ringbalk B82 238 Beam 4 250.125.6.9 0.5
Page 19 of
Assignmen 10/10/20
Max
UniqueNa Min
Story Label Design Length Analysis Station
Design Section Number
Stations
m
Ringbalk B83 239 Beam 4 0.5
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9 250.125.6.9
250.125.6.9
250.125.6.9
250.125.6.9
250.125.6.9
Kolom WF Kolom WF
Ringbalk C56 66 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 Kolom WF
Kolom WF
Ringbalk C90 110 Column 3 3
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Page 20 of
Assignmen 10/10/20
Max
Min
Stations
m
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF 300.150.6,5.9
Ringbalk C109
Kolom WF 300.150.6,5.9 36 Column Kolom WF 3
3 300.150.6,5.9
Kolom WF 300.150.6,5.9
Kolom WF 300.150.6,5.9
Ringbalk C110 37 Column Kolom WF 3
3 300.150.6,5.9
Kolom WF 300.150.6,5.9
Kolom WF 300.150.6,5.9
Ringbalk C111 38 Column Kolom WF
3 300.150.6,5.9 3
Kolom WF 300.150.6,5.9
Kolom WF 300.150.6,5.9
Ringbalk C112 39 Column Kolom WF
3 300.150.6,5.9 3
Balok B5 WF 300.150.6,5.9
Balok B5 WF 300.150.6,5.9 Kolom WF
Balok B5 WF 300.150.6,5.9
Ringbalk
Balok B5 WFC4
300.150.6,5.982 Column 3 300.150.6,5.9 3
Ringbalk
Balok B5 WFC5
300.150.6,5.994 Column 3 300.150.6,5.9 3
Balok B5 WF 300.150.6,5.9
Ringbalk Kolom WF
Balok B5 WFC6
300.150.6,5.9106 Column 3 300.150.6,5.9 3
Balok B5 WF 300.150.6,5.9
Balok
Lantai 3 B5 WFB44
300.150.6,5.9205 Beam Balok B5 WF
3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 3 B5 WFB45
300.150.6,5.9206 Beam Balok B5 WF
3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 3 B5 WFB46
300.150.6,5.9207 Beam Balok B5 WF
4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok B5 WF 300.150.6,5.9 Balok B5 WF
Lantai 3 B47 208 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 3 B5 WFB48
Balok 300.150.6,5.9209 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 3 B5 WFB49 Balok B5 WF
Balok 300.150.6,5.9210 Beam 4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 3 B5 WFB55
300.150.6,5.9186 Beam Balok B5 WF
3.5 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 3 B5 WFB57
300.150.6,5.9190 Beam Balok B5 WF
3.5 300.150.6,5.9 0.5
Lantai 3 B59 194 Beam Balok B5 WF

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

2 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

2 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5
Balok B5 WF
Lantai 3 B77 189 Beam 4 300.150.6,5.9 0.5
Balok B5 WF
Lantai 3 B78 191 Beam 2 300.150.6,5.9 0.5
Page 21 of
Assignmen 10/10/20
Max
UniqueNa Min
Stations
m
Lantai 3 B79 192 Beam 4 0.5
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C15 59 Column 3 3
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C20 62 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C21 63 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C23 77 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C25 78 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C26 79 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C27 80 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C34 81 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 3 C36 89 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 3 C37 90 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 3 C38 91 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 3 C41 92 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 3 C42 93 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 3 C44 101 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 3 C45 102 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Page 22 of
Assignmen 10/10/20
Max
Min
Stations
m
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF 300.150.6,5.9
Lantai 3 WF 300.150.6,5.9
Kolom C50 29 Column Kolom WF 3
6 300.150.6,5.9
Kolom WF 300.150.6,5.9
Kolom
Lantai 3 WF 300.150.6,5.9
C51 30 Column Kolom WF 3
6 300.150.6,5.9
Kolom WF 300.150.6,5.9
Balok
Lantai 3 B5 WF 300.150.6,5.931
C52 Column Kolom WF
6 300.150.6,5.9 3
Balok B5 WF 300.150.6,5.9
Balok
Lantai 3 B5 WF 300.150.6,5.932
C53 Column Kolom WF
6 300.150.6,5.9 3
Balok B5 WF 300.150.6,5.9
Lantai 3 C54 33 Column 6 300.150.6,5.9 3
Balok B5 WF 300.150.6,5.9
Lantai 2 B5 WF
Balok B139
300.150.6,5.970 Beam 3.5 300.150.6,5.9 0.5
Lantai 2 B5 WF
Balok B44
300.150.6,5.9154 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 2 B5 WF
B45 Balok B5 WF
Balok 300.150.6,5.9155 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 2 B5 WF 300.150.6,5.9156
B46 Beam Balok B5 WF
4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 2 B5 WF 300.150.6,5.9157
3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 2 B5 WF 300.150.6,5.9158
3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 2 B49 159 Beam 4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 2 B5 WF
Balok B50
300.150.6,5.9160 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 2 B5 WF
B51 Balok B5 WF
Balok 300.150.6,5.9161 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 2 B5 WF 300.150.6,5.9162
4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 2 B5 WF 300.150.6,5.9166
3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5
Balok B5 WF
Lantai 2 B72 163 Beam 2 300.150.6,5.9 0.5
Balok B5 WF
Lantai 2 B73 164 Beam 4 300.150.6,5.9 0.5
Page 23 of
Assignmen 10/10/20
Max
UniqueNa Min
Stations
m
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
300.150.6,5.9 300.150.6,5.9
Lantai 2 B94 65 Beam 3.5 0.5
300.150.6,5.9 300.150.6,5.9
Lantai 2 B95 71 Beam 3.5 0.5
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C22 40 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C23 41 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C25 42 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C26 43 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C27 44 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C34 45 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C35 46 Column 3 300.150.6,5.9 3
300.150.6,5.9
Kolom WF Kolom WF
Lantai 2 C36 47 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 2 C37 48 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 2 C38 49 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 2 C41 50 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 2 C42 51 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 2 C43 52 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
Lantai 2 C44 53 Column 3 300.150.6,5.9 3
300.150.6,5.9 Kolom WF
Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Page 24 of
Assignmen 10/10/20
Max
Min
Stations
m
Kolom WF Kolom WF
300.150.6,5.9 300.150.6,5.9
Kolom
Lantai 2 WF 300.150.6,5.9
C1 1 Column Kolom WF 3
Kolom WF 300.150.6,5.9 3 300.150.6,5.9
Balok B5 WF 300.150.6,5.9 300.150.6,5.9
Lantai 1 B5 WF
Balok B139
300.150.6,5.9300 Beam 3.5 300.150.6,5.9 0.5
Lantai 1 B5 WFB44
Balok 300.150.6,5.9271 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 1 B5 WFB45 Balok B5 WF
Balok 300.150.6,5.9272 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 1 B5 WFB46
300.150.6,5.9273 Beam Balok B5 WF
4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 1 B5 WFB47
300.150.6,5.9274 Beam Balok B5 WF
3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Balok
Lantai 1 B5 WFB48
300.150.6,5.9275 Beam Balok B5 WF
3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 1 B49 276 Beam 4 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
Lantai 1 B5 WFB50
Balok 300.150.6,5.9277 Beam 3 300.150.6,5.9 0.5
Balok B5 WF 300.150.6,5.9
3 300.150.6,5.9 0.5

4 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5

3.5 300.150.6,5.9 0.5
3.3 Shell Assignments
Table 3.3 - Area Assignments - Summary

UniqueNa Section Property
Story Label
mePropertyType
Ringbalk F29 6 Deck20 Deck
Lantai 3F822Deck20Deck
Lantai 3 F9 23 Deck20 Deck
Page 25 of
Assignmen 10/10/20
UniqueNa Section Property

Story Label
mePropertyType
Lantai 3F284Deck20Deck
Page 26 of
Loa 10/10/20
4 Loads
This chapter provides loading information as applied to the model.
4.1 Load Patterns

Table 4.1 - Load Pattern Definitions
Self
Is Auto
Name Type Weight Auto Load
Load Multiplier
~LLRF Yes Other 0
DL No Dead 1
EQS-X No Seismic 0 User Loads
EQS-Y No Seismic 0 User Loads
LL No Live 0
RL No Snow 0
SIDL No Super Dead 0
4.2 Load Sets
Table 4.2 - Shell Uniform Load Sets

LoadLoad NamePatternValue
kN/m2
Arsip DL 4.79
Atap Baja Ringan
DL 0.24
Kantor DL 2.4
Resto DL 4.79
Teras
DL 4.79
Balkon
4.3 Applied Loads

4.3.1 Line Loads
Table 4.5 - Frame Loads Assignments - Distributed

Absolute Absolute
Relative Relative
UniqueN Load Load Directio Distance Distance Distance Force A Force B
Story Label Distance Distance
ame Pattern Type n Type A B kN/m kN/m
A B m m
Ringbalk B47 226 SIDL Force Gravity Relative 0 1 0 3 8.829 8.829
Ringbalk B55 232 SIDL Force Gravity Relative 0 1 0 3.5 8.829 8.829
Ringbalk B61 240 SIDL Force Gravity Relative 0 1 0 3.5 8.829 8.829
Lantai 3 B47 208 SIDL Force Gravity Relative 0 1 0 3 7.358 7.358
Page 27 of
Loa 10/10/20
Absolute Absolute
Relative Relative
UniqueN Load Load Directio Distance Distance Distance Force A Force B
Story Label Distance Distance
ame Pattern Type n Type A B kN/m kN/m
A B m m
Lantai 3 B55 186 SIDL Force Gravity Relative 0 1 0 3.5 7.358 7.358
Page 28 of
Loa 10/10/20
4.3.2 Area Loads
Table 4.6 - Area Load Assignments - Uniform

UniqueNa Load Load
Story Label Direction
me Pattern kN/m2
Lantai 3 F8 22 LL Gravity 4.79
Lantai 3 F8 22 SIDL Gravity 1.48
Page 29 of
Loa 10/10/20
UniqueNa Load Load

Story Label Direction
me Pattern kN/m2
Table 4.7 - Area Load Assignments - Uniform Load Sets

UniqueNa Load Set
Story Label
me
Lantai 3 F8 22 Resto
Lantai 3F923Resto
Lantai 3F295Resto
Teras Balkon Teras Balkon Teras Balkon
Lantai 2 F5 7
Kantor Kantor Kantor Kantor Kantor Kantor Kantor Kantor Kantor
Kantor
Lantai 2 F6 8
Lantai 2 F7 9
Lantai
F8 F9 F10
2 F11 F12 F16 F17 F21
10F22
Lantai 2 F23 11
Lantai 2 12
Lantai 2 13
Lantai 2 14
Lantai 2 15
Lantai 2 16
Lantai 2 17
Lantai 2 18
Lantai 2 19
Lantai 2 F24 20 Kantor

Lantai 2 F25 21 Kantor
4.4 Functions
4.4.1 Response Spectrum Functions
Table 4.8 - Functions - Response Spectrum - User Defined

NamePeriodValueDamping secRatio
UnifRS 0 1 0.05
UnifRS11
Page 30 of
Loa 10/10/20
4.4.2 Time History Functions
Table 4.9 - Functions - Time History - User Defined

Time
Name Value
sec
RampTH 0 0
RampTH 1 1
RampTH 4 1
UnifTH 0 1
UnifTH 1 1
4.5 Load Cases

Table 4.10 - Load Case Definitions - Summary
Name Type
Modal -
Modal Eigen
DL Linear Static
LL Linear Static
SIDL Linear Static
RL Linear Static
EQS-X Linear
EQS-Y Linear Static
4.6 Load Combinations
Table 4.11 - Load Combination Definitions

Load Name
Name TypeIs Auto SF Notes
Kombinasi 1 Linear Add No DL 1.4
Kombinasi 2 LL 1.6
Kombinasi 2 SIDL 0.5
Kombinasi 3 SIDL 1.6
Kombinasi 3 LL 1
Kombinasi 4 LL 1
Page 31 of
Analysis 10/10/20
5 Analysis Results
This chapter provides analysis results.
5.1 Structure Results

Table 5.1 - Base Reactions
Output Case FX FY FZ MX MY MZ X Y Z
Case Type kN kN kN kN-m kN-m kN-m m m m
DL LinStatic 0 0 3723.9413 44443.6226 -31879.2328 0 0 0 0
LL LinStatic 0 0 1883.6675 21521.7694 -15845.0206 0 0 0 0
SIDL LinStatic 0 0 2695.909 30410.0153 -22799.9343 0 0 0 0
RL LinStatic 0 0 0 0 0 0 0 0 0
EQS-X LinStatic 0 0 0 0 0 0 0 0 0
EQS-Y LinStatic 0 0 0 0 0 0 0 0 0
Kombinasi 1 Combination 0 0 5213.5178 62221.0716 -44630.926 0 0 0 0
102972.185
Kombinasi 2 Combination 0 0 8830.5521 -75007.0795 0 0 0 0
7
123510.140
Kombinasi 3 Combination 0 0 10665.8515 9 -90579.9948 0 0 0 0
Kombinasi 4 Combination 0 0 6352.3971 74854.1165 -54100.1 0 0 0 0
5.2 Story Results
Table 5.2 - Story Drifts

Output Case X Y Z
Story Directio n Drift Label
Case Type m m m
Ringbalk DL LinStatic X 7.6E-05 67 13.5 3.5 9
Ringbalk DL LinStatic Y 0.000198 75 13.5 23 9
Ringbalk LL LinStatic X 4E-05 22 3.5 19 9
Ringbalk LL LinStatic Y 0.000128 75 13.5 23 9
Ringbalk SIDL LinStatic X 7.2E-05 25 13.5 19 9
Ringbalk SIDL LinStatic Y 8.6E-05 72 3.5 23 9
Ringbalk Kombinasi 1 Combination X 0.000106 67 13.5 3.5 9
Ringbalk Kombinasi 1 Combination Y 0.000277 75 13.5 23 9
Lantai 3 DL LinStatic X 3E-06 67 13.5 3.5 6
Lantai 3 LL LinStatic X 2E-06 67 13.5 3.5 6
Lantai 3 SIDL LinStatic X 1E-06 49 3.5 3.5 6
Lantai 3 Kombinasi 1 Combination X 5E-06 67 13.5 3.5 6
Lantai 2 DL LinStatic X 2.095E-07 51 3.5 11 3
Lantai 2 DL LinStatic Y 4.196E-07 66 13.5 0 3
Lantai 2 LL LinStatic X 1.125E-07 51 3.5 11 3
Lantai 2 LL LinStatic Y 2.027E-07 66 13.5 0 3
Lantai 2 SIDL LinStatic X 2.87E-07 34 0 7 3
Lantai 2 SIDL LinStatic Y 2.949E-07 135 0 3.5 3
Lantai 2 Kombinasi 1 Combination X 2.933E-07 51 3.5 11 3
Lantai 2 Kombinasi 1 Combination Y 1E-06 66 13.5 0 3
Lantai 2 Kombinasi 3 Combination X 4.829E-07 34 0 7 3
Lantai 2 Kombinasi 3 Combination Y 1E-06 135 0 3.5 3
Page 32 of
Analysis 10/10/20
Table 5.3 - Story Forces

Output Case P VX VY T MX MY
Story Location
Case Type kN kN kN kN-m kN-m kN-m
Ringbalk DL LinStatic Top 149.7509 0 0 0 2908.4828 -1505.4445
Ringbalk DL LinStatic Bottom 176.9665 0 0 0 3293.6882 -1736.7772
Ringbalk LL LinStatic Top 0 0 0 0 0 0
Ringbalk LL LinStatic Bottom 0 0 0 0 0 0
Ringbalk SIDL LinStatic Top 626.859 0 0 0 9621.4028 -5646.1455
Ringbalk SIDL LinStatic Bottom 626.859 0 0 0 9621.4028 -5646.1455
Ringbalk RL LinStatic Top 0 0 0 0 0 0
Ringbalk RL LinStatic Bottom 0 0 0 0 0 0
Ringbalk EQS-X LinStatic Top 0 0 0 0 0 0
Ringbalk EQS-X LinStatic Bottom 0 0 0 0 0 0
Ringbalk EQS-Y LinStatic Top 0 0 0 0 0 0
Ringbalk EQS-Y LinStatic Bottom 0 0 0 0 0 0
Ringbalk Kombinasi 1 Combination Top 209.6513 0 0 0 4071.8759 -2107.6224
Ringbalk Kombinasi 1 Combination Bottom 247.7531 0 0 0 4611.1635 -2431.488
5.3 Point Results
Table 5.4 - Joint Reactions

Unique Output Case FX FY FZ MX MY MZ
Story Label
Name Case Type kN kN kN kN-m kN-m kN-m
Lantai 3 53 97 DL LinStatic 0.4844 4.159 56.8867 34.8596 -0.2575 -1.7146
Lantai 3 53 97 LL LinStatic 0.08 2.2616 25.7535 15.1387 0.0001 -0.781
Lantai 3 53 97 SIDL LinStatic -1.2488 0.8891 54.8315 39.9122 -0.0006 1.7433
Lantai 3 53 97 RL LinStatic 0 0 0 0 0 0
Lantai 3 53 97 EQS-X LinStatic 0 0 0 0 0 0
Lantai 3 53 97 EQS-Y LinStatic 0 0 0 0 0 0
Lantai 3 53 97 Kombinasi 1 Combination 0.6782 5.8226 79.6414 48.8034 -0.3606 -2.4004
Lantai 3 53 97 Kombinasi 3 Combination -1.3368 8.675 181.7479 120.8296 -0.3099 -0.0492
Lantai 3 59 115 DL LinStatic 0.5517 4.0559 107.2451 66.2789 0.0005 -2.1184
Lantai 3 59 115 LL LinStatic 0.2078 1.9894 51.7032 31.4469 0.0002 -1.1673
Lantai 3 59 115 SIDL LinStatic -0.8832 0.4955 19.6417 13.5586 -0.0004 1.5553
Lantai 3 59 115 Kombinasi 1 Combination 0.7724 5.6783 150.1431 92.7905 0.0007 -2.9658
Lantai 3 59 115 Kombinasi 3 Combination -0.5432 7.6494 211.824 132.6754 0.0001 -1.221
Lantai 3 65 127 DL LinStatic -2.6104 -0.0785 121.6045 73.4989 -0.204 0.5651
Lantai 3 65 127 LL LinStatic -1.3138 -0.4279 59.7868 36.0636 -0.0003 0.2989
Lantai 3 65 127 SIDL LinStatic 1.0499 0.8643 18.6878 11.1088 0.0006 -1.0784
Lantai 3 65 127 Kombinasi 1 Combination -3.6546 -0.1099 170.2463 102.8985 -0.2855 0.7912
Lantai 3 65 127 Kombinasi 3 Combination -2.7665 0.8608 235.6127 142.0364 -0.244 -0.7484
Page 33 of
Analysis 10/10/20

Story Label
Lantai 3 71 139 DL LinStatic -2.2829 -3.4605 69.7766 40.3949 0.461 0.8091
Lantai 3 71 139 LL LinStatic -1.1074 -2.1466 33.2368 19.1132 -0.0002 0.3374
Lantai 3 71 139 SIDL LinStatic 1.4204 1.789 55.6379 39.1919 0.0008 -1.4832
Lantai 3 71 139 Kombinasi 1 Combination -3.1961 -4.8446 97.6872 56.5529 0.6454 1.1328
Lantai 3 71 139 Kombinasi 3 Combination -1.5742 -3.4368 205.9893 130.2942 0.5543 -1.0647
Lantai 3 72 147 DL LinStatic 1.0535 -0.8376 56.8044 -41.3924 0.3621 0.8053
Lantai 3 72 147 LL LinStatic 0.2392 -0.3325 24.4202 -19.4034 -0.0058 0.3542
Lantai 3 72 147 SIDL LinStatic 1.2281 -1.6942 81.9534 -35.4706 -3.4185 -0.8559
Lantai 3 72 147 Kombinasi 1 Combination 1.4748 -1.1727 79.5262 -57.9494 0.5069 1.1274
Lantai 3 72 147 Kombinasi 2 Combination 2.2609 -2.3843 148.2144 -98.4516 -1.2841 1.1051
Lantai 3 72 147 Kombinasi 3 Combination 3.4683 -4.0484 223.711 -125.8273 -5.0409 -0.0489
Lantai 3 73 149 DL LinStatic 0.4063 -1.2354 91.6004 -80.1986 -0.2607 0.9732
Lantai 3 73 149 SIDL LinStatic -0.2541 -0.1852 62.9464 -14.1406 0.4705 -0.7524
Lantai 3 74 151 DL LinStatic -0.335 0.3507 170.9252 -67.6848 -0.5779 -0.4389
Lantai 3 74 151 LL LinStatic -0.3732 -0.4138 70.558 -33.0225 -0.4178 -0.2297
Lantai 3 74 151 SIDL LinStatic 2.5005 0.9172 115.6973 -1.604 -2.1615 0.5567
Lantai 3 74 151 Kombinasi 1 Combination -0.4689 0.491 239.2953 -94.7588 -0.8091 -0.6145
Lantai 3 74 151 Kombinasi 2 Combination 0.2511 0.2173 375.8517 -134.8598 -2.4427 -0.6159
Lantai 3 74 151 Kombinasi 3 Combination 3.2256 1.4745 460.784 -116.8107 -4.5697 0.1343
Lantai 3 75 153 DL LinStatic -2.3967 0.2316 136.1169 -27.4926 -1.8211 -0.5322
Lantai 3 75 153 LL LinStatic -0.562 -0.3923 51.8547 -12.622 -0.6112 -0.2295
Lantai 3 75 153 SIDL LinStatic -3.9617 -0.0565 137.4599 -24.4767 5.7816 0.7574
Lantai 3 75 153 Kombinasi 2 Combination -5.7561 -0.378 315.0377 -65.4246 -0.2724 -0.6272
Lantai 3 75 153 Kombinasi 3 Combination -9.7768 -0.2048 435.1308 -84.7758 6.4541 0.3437
Lantai 3 75 153 Kombinasi 4 Combination -3.4381 -0.1144 215.195 -45.6131 -2.7965 -0.8682
Lantai 3 76 155 DL LinStatic -0.1609 -1.7526 58.6072 -24.0304 0.3063 -2.66E-05
Lantai 3 76 155 LL LinStatic -0.0327 -0.0827 18.7797 -12.6048 -0.0617 -4.171E-05
Lantai 3 76 155 Kombinasi 1 Combination -0.2252 -2.4536 82.05 -33.6426 0.4288 -3.724E-05
Lantai 3 76 155 Kombinasi 2 Combination -2.4562 -2.8297 133.6818 -55.2818 3.3405 -0.0001
Page 34 of
Analysis 10/10/20

Story Label
Lantai 3 77 157 DL LinStatic 0.1334 -1.6181 58.1728 -24.1851 -0.3605 -0.0001
Lantai 3 77 157 LL LinStatic -0.0384 0.0224 18.3583 -12.7205 -0.0747 -2.773E-05
Lantai 3 77 157 SIDL LinStatic 5.3132 -1.5615 69.1285 -12.2138 -4.4504 -0.0001
Lantai 2 49 10 DL LinStatic 1.396 0.1421 107.9491 0.5697 -2.4786 -0.0587
Lantai 2 49 10 LL LinStatic 0.8486 0.1766 61.0824 7.5389 -1.2288 -0.037
Lantai 2 49 10 SIDL LinStatic 0.8999 0.1203 104.2168 7.1407 -6.6662 0.1152
Lantai 2 49 10 Kombinasi 3 Combination 3.9636 0.5396 357.3681 19.6477 -14.8691 0.0769
Lantai 2 53 18 LL LinStatic 0.2002 -0.4948 5.6147 -2.5893 -4.918E-05 0.0339
Lantai 2 53 18 SIDL LinStatic -0.2009 0.0018 19.597 -4.7208 -5.5181 -0.058
Lantai 2 65 78 LL LinStatic 0.2569 -0.506 13.1923 -5.9333 1.555E-05 0.0428
Lantai 2 65 78 SIDL LinStatic -0.1579 -0.3976 29.762 -1.8502 -4.2919 -0.051
Lantai 2 71 90 DL LinStatic 0.1549 -0.5359 14.1529 -6.3813 0.4615 0.0132
Lantai 2 71 90 LL LinStatic 0.0667 -0.2564 7.6139 -3.4902 3.908E-05 0.0016
Lantai 2 71 90 SIDL LinStatic -0.0161 -0.3641 23.9231 -5.0702 9.81 0.0303
Page 35 of
Analysis 10/10/20

Story Label
Lantai 1 34 166 DL LinStatic 0.6471 -0.8949 18.5375 0.5196 0.2425 0
Lantai 1 34 166 LL LinStatic 0.2781 -0.8675 15.0022 0.8489 0.2574 0
Lantai 1 34 166 SIDL LinStatic 0.4804 -0.2681 30.747 -7.2482 -7.0688 0
Lantai 1 34 166 Kombinasi 1 Combination 0.9059 -1.2529 25.9525 0.7274 0.3395 0
Lantai 1 34 166 Kombinasi 2 Combination 1.4616 -2.5959 61.6221 -1.6423 -2.8315 0
Lantai 1 34 166 Kombinasi 3 Combination 1.8232 -2.3704 86.4424 -10.1247 -10.7617 0
Lantai 1 135 165 DL LinStatic 0.0079 0.8962 17.7494 -0.5209 -0.3481 0
Lantai 1 135 165 LL LinStatic -0.0899 0.8682 14.5458 -0.8496 -0.0826 0
Lantai 1 135 165 SIDL LinStatic -0.0273 0.2681 30.2457 7.2486 -7.5355 1.126E-06
Lantai 1 135 165 Kombinasi 1 Combination 0.011 1.2547 24.8492 -0.7292 -0.4874 5.796E-07
Lantai 1 135 165 Kombinasi 2 Combination -0.1481 2.5987 59.6954 1.6399 -4.3176 1.737E-06
Lantai 1 135 165 Kombinasi 3 Combination -0.1242 2.3727 84.2382 10.1231 -12.5571 2.721E-06
Lantai 1 135 165 Kombinasi 4 Combination -0.0805 1.9437 35.8451 -1.4746 -0.5003 9.199E-07
Lantai 1 48 7 LL LinStatic 0.0709 0.4266 9.9275 -0.4175 0.0653 0
Lantai 1 48 7 SIDL LinStatic 0.0298 0.2636 30.0347 7.2528 -5.4908 0
Lantai 1 48 7 Kombinasi 1 Combination 0.3189 1.2162 31.9655 -0.6914 -0.0723 -6.608E-07
Lantai 1 48 7 Kombinasi 2 Combination 0.4017 1.8568 58.3004 2.3658 -2.7029 -9.284E-07
Lantai 1 48 7 Kombinasi 3 Combination 0.3919 1.8909 85.382 10.5944 -8.7819 -9.357E-07
Lantai 1 48 7 Kombinasi 4 Combination 0.3442 1.4691 37.3265 -1.0101 0.0033 -7.58E-07
Lantai 1 49 9 DL LinStatic 0 0 2.8786 0 0.0945 0
Lantai 1 49 9 LL LinStatic 0 0 0 0 0 0
Lantai 1 49 9 SIDL LinStatic 0 0 49.6631 0 1.9927 0
Lantai 1 49 9 Kombinasi 1 Combination 0 0 4.03 0 0.1323 0
Lantai 1 50 11 DL LinStatic 0.4774 -0.1024 118.9345 -0.2559 0.5377 0
Lantai 1 50 11 SIDL LinStatic 1.059 0.0742 148.8601 -7.5834 2.9713 0
Lantai 1 50 11 Kombinasi 1 Combination 0.6684 -0.1434 166.5083 -0.3583 0.7527 -5.735E-07
Lantai 1 50 11 Kombinasi 3 Combination 2.5271 -0.1815 447.6582 -12.2669 5.6404 0
Lantai 1 51 13 DL LinStatic 0.4176 0.0917 117.0472 -0.0897 0.3885 0
Lantai 1 51 13 SIDL LinStatic -0.2642 0.0482 110.4964 -0.0472 -0.2456 0
Page 36 of
Analysis 10/10/20

Story Label
Lantai 1 51 13 Kombinasi 1 Combination 0.5847 0.1284 163.866 -0.1256 0.5439 0
Lantai 1 52 15 SIDL LinStatic -0.2079 -0.3713 92.0565 0.3633 -0.1932 0
Lantai 1 53 17 DL LinStatic 0 0 0.5234 0 0 0
Lantai 1 53 17 SIDL LinStatic 0 0 0 0 0 0
Lantai 1 53 17 Kombinasi 1 Combination 0 0 0.7327 0 0 0
Lantai 1 54 55 SIDL LinStatic 0.0028 0.5834 45.0016 6.9398 0.0024 0
Lantai 1 54 55 Kombinasi 3 Combination 0.238 4.5939 148.2959 7.9491 0.2185 0
Lantai 1 55 57 SIDL LinStatic 0.4075 -0.1759 142.7676 0.1722 0.3769 0
Lantai 1 55 57 Kombinasi 1 Combination 0.8987 -1.0136 202.3901 0.9921 0.8325 -5.735E-07
Page 37 of
Analysis 10/10/20

Story Label
Lantai 1 58 63 SIDL LinStatic -0.1872 -0.1552 31.5476 0.1519 -0.1737 0
Lantai 1 60 67 SIDL LinStatic -0.0304 0.3542 45.3269 7.1642 -4.3203 0
Lantai 1 60 67 Kombinasi 1 Combination 0.0308 3.5692 75.2534 -2.9941 -0.2571 0
Lantai 1 60 67 Kombinasi 2 Combination -0.0216 5.1785 125.9024 -0.8848 -2.4113 -6.425E-07
Lantai 1 60 67 Kombinasi 3 Combination -0.0427 4.8398 161.236 7.7085 -7.1521 -6.597E-07
Lantai 1 60 67 Kombinasi 4 Combination 0.0059 4.2731 88.7129 -3.7542 -0.2396 -5.086E-07
Lantai 1 61 69 DL LinStatic -0.0466 -0.8447 171.3682 0.8268 -0.2463 0
Lantai 1 61 69 LL LinStatic -0.0496 -0.2733 87.5325 0.2676 -0.0458 0
Lantai 1 61 69 SIDL LinStatic 0.8267 0.2591 175.111 -0.2535 -3.527 0
Lantai 1 61 69 Kombinasi 1 Combination -0.0652 -1.1826 239.9155 1.1576 -0.3448 0
Lantai 1 61 69 Kombinasi 2 Combination 0.2781 -1.3215 433.2493 1.2935 -2.1323 0
Lantai 1 61 69 Kombinasi 3 Combination 1.2173 -0.8725 573.3519 0.8541 -5.9845 0
Lantai 1 62 71 DL LinStatic -0.0625 0.4803 232.1121 -0.8262 -0.2605 0
Lantai 1 62 71 SIDL LinStatic 1.1109 -0.3062 120.4043 -7.2111 -3.2642 0
Lantai 1 62 71 Kombinasi 1 Combination -0.0876 0.6724 324.9569 -1.1566 -0.3647 0
Page 38 of
Analysis 10/10/20

Story Label
Lantai 1 66 79 DL LinStatic -0.2587 1.4827 31.8252 -1.0946 0.2256 0
Lantai 1 66 79 SIDL LinStatic -0.0109 0.2099 31.245 7.3054 9.7999 0
Lantai 1 66 79 Kombinasi 1 Combination -0.3621 2.0757 44.5553 -1.5324 0.3158 0
Lantai 1 66 79 Kombinasi 2 Combination -0.3944 3.0033 76.145 1.2441 5.0975 0
Lantai 1 66 79 Kombinasi 3 Combination -0.3769 2.8145 102.1399 9.6907 15.9047 7.69E-07
Lantai 1 67 81 DL LinStatic -0.3043 -0.4856 112.1001 0.4754 0.1837 0
Lantai 1 67 81 SIDL LinStatic -2.0237 0.232 144.8431 -0.2271 7.9358 0
Lantai 1 67 81 Kombinasi 1 Combination -0.426 -0.6798 156.9401 0.6655 0.2572 0
Lantai 1 68 83 DL LinStatic -0.3201 0.2715 136.5041 -0.6218 0.1694 0
Lantai 1 68 83 SIDL LinStatic -2.1992 0.052 151.1273 -7.5617 7.7749 0
Page 39 of
Analysis 10/10/20

Story Label
Page 40 of
Analysis 10/10/20

Story Label
5.4 Modal Results

Table 5.5 - Modal Periods And Frequencies
Frequenc CircFreq Eigenvalu
Period sec
Case Mode y e
rad/sec
cyc/sec rad2/sec2
Modal 1 0.514 1.945 12.2186 149.2948
Modal 2 0.405 2.467 15.5 240.2501
Modal 3 0.31 3.221 20.2373 409.5484
Modal 4 0.248 4.038 25.3707 643.6709
Modal 5 0.213 4.693 29.4876 869.5208
Modal 6 0.19 5.261 33.0553 1092.6509
Modal 7 0.155 6.455 40.5599 1645.107
Modal 8 0.147 6.782 42.6153 1816.0615
Modal 9 0.089 11.185 70.2783 4939.0429
Modal 10 0.085 11.748 73.8145 5448.5854
Modal 11 0.081 12.387 77.8305 6057.5851
Modal 12 0.061 16.346 102.7066 10548.6383
Page 41 of
Analysis 10/10/20
Table 5.6 - Modal Participating Mass Ratios (Part 1 of 2)

Period
Case Mode UX UY UZ SumUX SumUY SumUZ RX RY RZ SumRX
sec
Modal 1 0.514 0 0.1614 0 0 0.1614 0 0.5698 7.166E-07 0.0051 0.5698
Modal 2 0.405 0.001 0.0002 0 0.001 0.1615 0 0.0008 0.0028 0.0574 0.5706
Modal 3 0.31 0.0005 0.0055 0 0.0016 0.167 0 0.0181 0.0019 0.025 0.5887
Modal 4 0.248 0.088 2.723E-05 0 0.0896 0.167 0 0.0001 0.31 0.2194 0.5888
Modal 5 0.213 3.229E-05 0.0023 0 0.0896 0.1693 0 0.0076 0.0001 4.826E-05 0.5964
Modal 6 0.19 0.0994 0 0 0.189 0.1693 0 9.234E-07 0.231 0.0601 0.5964
Modal 7 0.155 0.0305 0 0 0.2195 0.1693 0 0 0.0915 0.0013 0.5964
Modal 8 0.147 4.468E-05 0 0 0.2195 0.1693 0 0 0.0007 0.0016 0.5964
Modal 9 0.089 0.0079 0 0 0.2274 0.1693 0 1.006E-06 0.0013 0.0079 0.5964
Modal 10 0.085 0.1974 4.273E-06 0 0.4248 0.1693 0 0 0.0221 0.142 0.5964
Modal 11 0.081 0.0003 0 0 0.4251 0.1693 0 8.921E-06 0.0003 0.0002 0.5964
Modal 12 0.061 0 7.361E-07 0 0.4251 0.1693 0 1.257E-06 2.466E-06 1.237E-05 0.5964
Table 5.6 - Modal Participating Mass Ratios (Part 2 of 2)

SumRY SumRZ
7.166E-07 0.0051
0.0028 0.0624
0.0047 0.0874
0.3147 0.3068
0.3148 0.3069
0.5458 0.367
0.6373 0.3683
0.638 0.3699
0.6393 0.3778
0.6613 0.5198
0.6616 0.52
0.6616 0.52
Table 5.7 - Modal Load Participation Ratios

StaticDynamic
CaseItemTypeItem
%%
ModalAccelerationUX 94.6 42.51
Modal Acceleration UY 98.23 16.93
Modal Acceleration UZ 0 0
Table 5.8 - Modal Direction Factors

Period
Case Mode UX UY UZ RZ
sec
Modal 1 0.514 0 0.973 0 0.026
Modal 2 0.405 0.003 0.004 0 0.993
Modal 3 0.31 0.003 0.016 0 0.982
Modal 4 0.248 0.982 0.001 0 0.018
Modal 5 0.213 0 0.007 0 0.992
Modal 6 0.19 0.959 0 0 0.041
Modal 7 0.155 0.89 0 0 0.11
Modal 8 0.147 0.716 0 0 0.284
Modal 9 0.089 0.001 0 0 0.999
Modal 10 0.085 0.221 0 0 0.779
Modal 11 0.081 0.001 0.001 0 0.998
Modal 12 0.061 0.003 0 0 0.997
Page 42 of
Analysis 10/10/20
Gambar. Check Model
Page 43 of
Analysis 10/10/20
Gambar. Penampang Momen
Page 44 of
Analysis 10/10/20
Gambar. Penampang Geser Maksimum
Page 45 of
Analysis 10/10/20
Gambar. Momen Maksimum Balok B5
Page 46 of
Analysis 10/10/20
Gambar. Momen Balok B5 ¼ Bentang
Page 47 of
Analysis 10/10/20
Gambar. Momen Balok B5 1/2 Bentang
Page 48 of
Analysis 10/10/20
Gambar. Momen Balok B5 3/4 Bentang
Page 49 of
Analysis 10/10/20
Gambar. Momen Maksimum Balok B6
Page 50 of
Analysis 10/10/20
Gambar. Momen Balok B6 ¼ Bentang
Page 51 of
PERHITUNGAN FONDASI FOOTPLAT
BENTUK EMPAT PERSEGI PANJANG
A. DATA FONDASI FOOT
DATA TANAH
Kedalaman fondasi, Df = 2.00 m
Berat volume tanah, = 17.60 kN/m3
Sudut gesek dalam, = 34.00 
Kohesi, c= 20.00 kPa
Tahanan konus rata-rata (hasil pengujian sondir), qc = 95.00 kg/cm2
DIMENSI FONDASI
Lebar fondasi arah x, Bx = 1.20 m
Lebar fondasi arah y, By = 1.20 m
Tebal fondasi, h= 0.35 m
Lebar kolom arah x, bx = 0.30
m
Lebar kolom arah y, by = 0.30
m
Posisi kolom (dalam = 40, tepi = 30, sudut = 20) s = 40
BAHAN KONSTRUKSI
Kuat tekan beton, fc' = 25.0
MPa
Kuat leleh baja tulangan, fy = 400
MPa
Berat beton bertulang, c = 24
kN/m3
BEBAN RENCANA FONDASI
Gaya aksial akibat beban terfaktor, Pu = 538.000
Momen arah x akibat beban terfaktor, Mux = 9.000 kN
Momen arah y akibat beban terfaktor, Muy = 30.000 kNm
kNm
B. KAPASITAS DUKUNG
1. MENURUT TERZAGHI DAN PECK (1943)
Kapasitas dukung ultimit tanah menurut Terzaghi dan Peck (1943) :

c = kohesi
qu = ctanah * (1 +) 0.3 * B / L) + Df *  * Nq + 0.5 * B * N * (1c -=0.2 *20.00
* Nc(kN/m
2
B / L) 
Df = Kedalaman fondasi (m) Df = 2.00 m
 = berat volume tanah (kN/m3) = 17.60 kN/m3
B = lebar fondasi (m) B = By = 1.20 m
L = panjang fondasi (m) L = By = 1.20 m
Sudut gesek dalam, = 34.00 
 =  / 180 *  = 0.59341195 rad
= 4.01140898
(3* / 4 - /2)*tan 
a=e
Kp = 3 * tan [ 45 + 1/2*(  + 33) ] = 72.4763059
2
Faktor kapasitas dukung tanah menurut Terzaghi :

Nc = 1/ tan  * [ a2 / (2 * cos2 (45 + /2) - 1 ] = 52.637
Nq = a2 / [ (2 * cos2 (45 + /2) ] = Nc * tan  + 1 = N 36.504
= 1/2 * tan  * [ Kp / cos2  - 1 ] = 35.226
Kapasitas dukung ultimit tanah menurut Terzaghi :
qu = c*Nc*(1+0.3*B/L) + Df**Nq + 0.5*B*N*(1-0.2*B/L) = 2670.44 kN/m2
Kapasitas dukung tanah, qa = qu / 3 = 890.15 kN/m2
2. MENURUT MEYERHOF (1956)
Kapasitas dukung tanah menurut Meyerhof (1956) :

q ac= q / 33 * [ ( B + 0.3 ) / B ]2 * K d ( dalam kg/cm2)
harus  1.33
dengan, Kd = 1 + 0.33 * Df / B
qc = tahanan konus rata-rata hasil sondir pada dasar fondasi ( kg/cm2 )

B = lebar fondasi (m) B = By = 1.20 m
Df = Kedalaman fondasi (m) Df = 2.00 m
Kd = 1 + 0.33 * Df / B = 1.55 > 1.33
 diambil, Kd = 1.33
95.00
Tahanan konus rata-rata hasil sondir pada dasar fondasi, qc = kg/cm2
a 5.982
q = cq / 33 * [ ( B + 0.3 ) / B ]2 * Kd = kg/cm2
598.25
Kapasitas dukung ijin tanah, qa = kN/m2
3. KAPASITAS DUKUNG TANAH YANG DIPAKAI
Kapasitas dukung tanah menurut Terzaghi dan Peck : qa = 890.15 kN/m2

Kapasitas dukung tanah tanah menurut Meyerhof : qa = 598.25 kN/m2
Kapasitas dukung tanah yang dipakai : qa = 598.25 kN/m2
C. KONTROL TEGANGAN
Luas dasar foot plat, A = Bx * By = m 2

1.4400
Tahanan momen arah x, Wx = 1/6 * By * Bx2 = 0.2880 m
3
Tahanan momen arah y, Wy = 1/6 * Bx * B 2 = 0.2880 m

3
y
Tinggi tanah di atas foot plat, z = Df - h = 1.65 m
37.440
Tekanan akibat berat foot plat dan tanah, q = h * c + z *  = kN/m2
Eksentrisitas pada fondasi :
ex = Mux / Pu = 0.0167 m < Bx / 6 = 0.2000 m (OK)
ey = Muy / Pu = 0.0558 m < By / 6 = 0.2000 m (OK)
Tegangan tanah maksimum yang terjadi pada dasar fondasi :
546.468
qmax = Pu / A + Mux / Wx + Muy / Wy + q = kN/m2
qmax < qa  AMAN (OK)
Tegangan tanah minimum yang terjadi pada dasar fondasi :
qmin = P / A - M / W - M / W + q = 275.634 kN/m2
u ux x uy y
qmin > 0  tak terjadi teg.tarik (OK)

D. GAYA GESER PADA FOOT
1. TINJAUAN GESER ARAH X
Jarak pusat tulangan terhadap sisi luar beton, d' = 0.075 m

Tebal efektif foot plat, d = h - d' = 0.275 m
Jarak bid. kritis terhadap sisi luar foot plat, ax = ( Bx - bx - d ) / 2 = 0.313 m
Tegangan tanah pada bidang kritis geser arah x,
qx = qmin + (Bx - ax) / Bx * max - qmin) = 475.938 kN/m2
(q 177.661
Gaya geser arah x, Vux = [ qx + ( qmax - qx ) / 2 - q ] * ax * By = 1200 kN
Lebar bidang geser untuk tinjauan arah x, b = By = 275 mm
Tebal efektif footplat, d= 1.0000 mm
Rasio sisi panjang thd. sisi pendek kolom, c = bx / by =
Kuat geser foot plat arah x, diambil nilai terkecil dari Vc yang diperoleh dari pers.sbb. :
Vc = [ 1 + 2 / c ] * √ fc' * b * d / 6 * 10-3 = 825.000 kN
Vc = [ s * d / b + 2 ] * √ fc' * b * d / 12 * 10-3 = 1535.417 kN
Vc = 1 / 3 * √ fc' * b * d * 10-3 = 550.000 kN
Diambil, kuat geser foot plat,  Vc = 550.000 kN
Faktor reduksi kekuatan geser,  = 0.75
Kuat geser foot plat,   Vc = 412.500 kN
Syarat yang harus dipenuhi,
  Vc ≥ Vux
412.500 > 177.661  AMAN (OK)
2. TINJAUAN GESER ARAH

Jarak bid. kritis terhadap sisi luar foot plat, ay = ( By - by - d ) / 2 = 0.318 m
Tegangan tanah pada bidang kritis geser arah y,
qy = qmin + (By - ay) / By * max - qmin) = 474.810 kN/m2
(q 180.289
Gaya geser arah y, Vuy = [ qy + ( qmax - qy ) / 2 - q ] * ay * Bx = 1200 kN
Lebar bidang geser untuk tinjauan arah y, b = Bx = 265 mm
Tebal efektif footplat, d= 1.0000 mm
Rasio sisi panjang thd. sisi pendek kolom, c = bx / by =
Kuat geser foot plat arah y, diambil nilai terkecil dari Vc yang diperoleh dari pers.sbb. :
Vc = [ 1 + 2 / c ] * √ fc' * b * d / 6 * 10-3 = 795.000 kN
Vc = [ s * d / b + 2 ] * √ fc' * b * d / 12 * 10-3 = 1435.417 kN
Vc = 1 / 3 * √ fc' * b * d * 10-3 = 530.000 kN
Diambil, kuat geser foot plat,  Vc = 530.000 kN
Faktor reduksi kekuatan geser,  = 0.75
Kuat geser foot plat,   Vc = 397.500 kN
Syarat yang harus dipenuhi,
  Vc ≥ Vux
397.500 > 180.289  AMAN (OK)
3. TINJAUAN GESER DUA ARAH

Lebar bidang geser pons arah x, cx = bx + 2 * d = 0.565 m
Lebar bidang geser pons arah y, cy = by + 2 * d = 0.565 m
Gaya geser pons yang terjadi,
Vup = ( Bx * By - cx * cy ) * [ ( qmax + qmin ) / 2 - q ] = 418.734 kN
Luas bidang geser pons, Ap = 2 * ( cx + cy ) * d = 0.599 m
2
Lebar bidang geser pons, bp = 2 * ( cx + cy ) = Rasio 2.260 m

sisi panjang thd. sisi pendek kolom,  c = bx / by = 1.0000
Tegangan geser pons, diambil nilai terkecil dari fp yang diperoleh dari pers.sbb. :
fp = [ 1 + 2 / c ] * √ fc' / 6 = MPa
2.500
fp = [ s * d / bp + 2 ] * √ fc' / 12 = MPa
2.788
fp = 1 / 3 * √ fc' = 1.667 MPa
Tegangan geser pons yang disyaratkan, fp = 1.667 MPa
Faktor reduksi kekuatan geser pons,  = 0.75
Kuat geser pons,  * Vnp =  * Ap * fp * 103 = 748.63 kN
Syarat :  * Vnp ≥ Vup
748.625 > 418.734  AMAN (OK)
 * Vnp ≥ Pu
748.625 > 538.000  AMAN (OK)
E. PEMBESIAN FOOTPLAT
1. TULANGAN LENTUR ARAH X
Jarak tepi kolom terhadap sisi luar foot plat, ax = ( Bx - bx ) / 2 = 0.450 m

Tegangan tanah pada tepi kolom,
qx = qmin + (Bx - ax) / Bx * max - qmin) = 444.905 kN/m2
(q
Momen yang terjadi pada plat fondasi akibat tegangan tanah,
Mux = 1/2 * ax2 * [ qx + 2/3 * ( qmax - qx ) - q ] * By = 57.734 kNm
Lebar plat fondasi yang ditinjau, b = By = 1200 mm
Tebal plat fondasi, h= 350 mm
Jarak pusat tulangan thd. sisi luar beton, d' = 75 mm
Tebal efektif plat, d = h - d' = 275 mm
Kuat tekan beton, fc' = 25 MPa
Kuat leleh baja tulangan, fy = 400 MPa
Modulus elastis baja, Es = 2.00E+05 MPa
Faktor distribusi teg. beton, 1 = 0.85
b = 1* 0.85 * fc’/ fy * 600 / ( 600 + fy ) = 0.02709375
Faktor reduksi kekuatan lentur,  = 0.80
Rmax = 0.75 * b * fy * [1-½*0.75* b * fy / ( 0.85 * fc’ ) ] = 6.574
Mn = Mux /  = 72.167 kNm
6 2
Rn = Mn * 10 / ( b * d ) = 0.79523
Rn < Rmax  (OK)
Rasio tulangan yang diperlukan,
 = 0.85 * fc’ / fy * [ 1 -  {1 – 2 * Rn / ( 0.85 * fc’ ) } ] = 0.0020
Rasio tulangan minimum, min = 0.0025
Rasio tulangan yang digunakan, Luas  = 0.0025
tulangan yang diperlukan, 825.00 mm2
As =  * b * d =
Diameter tulangan yang digunakan, D 12 mm
Jarak tulangan yang diperlukan, Jarak s =  / 4 * D * b / As =
2
165 mm
tulangan maksimum, smax = 200 mm
Jarak tulangan yang digunakan,  s= 165 mm
Digunakan tulangan, D 12 - 160
Luas tulangan terpakai, As =  / 4 * D * b / s
2
= 848.23 mm2
2. TULANGAN LENTUR ARAH Y
Jarak tepi kolom terhadap sisi luar foot plat, ay = ( By - by ) / 2 = 0.450 m

Tegangan tanah pada tepi kolom,
qy = qmin + (By - ay) / By * max - qmin) = 444.905 kN/m2
(q
Momen yang terjadi pada plat fondasi akibat tegangan tanah,
Muy = 1/2 * ay2 * [ q y+ 2/3 * ( q ma x- qy ) - q ] * Bx = 57.734 kNm
Lebar plat fondasi yang ditinjau, b = Bx = 1200 mm
Tebal plat fondasi, h= 350 mm
Jarak pusat tulangan thd. sisi luar beton, d' = 85 mm
Tebal efektif plat, d = h - d' = 265 mm
Kuat tekan beton, fc' = 25 MPa
Kuat leleh baja tulangan, fy = 400 MPa
Modulus elastis baja, Es = 2.00E+05 MPa
Faktor distribusi teg. beton, 1 = 0.85
b = 1* 0.85 * fc’/ fy * 600 / ( 600 + fy ) = 0.02709375
Faktor reduksi kekuatan lentur,  = 0.80
Rmax = 0.75 * b * fy * [1-½*0.75* b * fy / ( 0.85 * fc’ ) ] = 6.574
Mn = Muy /  = 72.167 kNm
6 2
Rn = Mn * 10 / ( b * d ) = 0.85638
Rn < Rmax  (OK)

Rasio tulangan yang diperlukan,
 = 0.85 * fc’ / fy * [ 1
-  {1 – 2 * Rn / ( 0.85 * fc’ ) } ] = 0.0022
Rasio tulangan minimum, min = 0.0025
Rasio tulangan yang digunakan, Luas
 = 0.0025
tulangan yang diperlukan, 795.00 mm2
As =  * b * d =
Diameter tulangan yang digunakan, D 12 mm
Jarak tulangan yang diperlukan, Jarak s =  / 4 * D * b / As =
2
171 mm
tulangan maksimum, smax = 200 mm
Jarak tulangan yang digunakan,  s= 171 mm
Digunakan tulangan, D 12 - 170
Luas tulangan terpakai, As =  / 4 * D * b / s
2
= 798.33 mm2
3. TULANGAN SUSUT
Rasio tulangan susut minimum, smin = 0.0014

Luas tulangan susut arah x, Asx = smi n* d * Bx = 462.000 mm2
Luas tulangan susut arah y, Asy = smi n* d * By = 445.200 mm2
Diameter tulangan yang digunakan,  10 mm
Jarak tulangan susut arah x,

sx =  / 4 * 2 * By / Asx = 204 mm
Jarak tulangan susut maksimum arah x, sx,max = 200 mm
Jarak tulangan susut arah x yang digunakan,  sx = 200 mm
Jarak tulangan susut arah y, sy =  / 4 * 2 * Bx / Asy = 212 mm
Jarak tulangan susut maksimum arah y, sy,max = 200 mm
Jarak tulangan susut arah y yang digunakan,  sy = 200 mm
 10 - 200
Digunakan tulangan susut arah x,
 10 - 200
Digunakan tulangan susut arah y,
PERHITUNGAN KOLOM LENTUR DUA ARAH (BIAXIAL )
KOLOM BAJA BANGUNAN
A. DATA BAHAN
Tegangan leleh baja (yield stress ),

fy = 240 MPa
Tegangan sisa (residual stress ),
fr = 70 MPa
Modulus elastik baja (modulus of elasticity ), MPa
E= 200000
Angka Poisson (Poisson's ratio ),
= 0.3
B. DATA PROFIL BAJA

Profil : WF (300x150x6/5x9)
ht = 300 mm
tf bf = 150 mm
tw = 6.5 mm
tf = 9
mm
t w ht r= 13
mm
h h2 A= 4678
mm2
Ix = 124000
mm4
Iy = 32900
mm4
h r rx = 136.5
mm
1 ry = 39
mm
bf Sx = 67700
mm3
Sy = 481000
mm3
C. DATA KOLOM
Panjang elemen thd.sb. x, mm

Lx = 6000
Panjang elemen thd.sb. y, mm
Ly = 1500
Gaya aksial akibat beban terfaktor, N
Nu = 108900
Momen akibat beban terfaktor thd.sb. x, Mux = 16621966 Nmm
Momen akibat beban terfaktor thd.sb. y, Muy = 9785360 Nmm
Gaya geser akibat beban terfaktor, Vu = 207000 N
Faktor reduksi kekuatan untuk aksial tekan, n = 0.85
Faktor reduksi kekuatan untuk lentur, Faktor b = 0.90
reduksi kekuatan untuk geser, f = 0.75
1
D. SECTION PROPERTIES
G = E / [2*(1 + )] = 76923.0769 MPa
h1 = tf + r = 22.00 mm
h2 = ht - 2 * h1 = 256.00 mm
h = ht - tf = 291.00 mm
J =  [ b * t /3 ] = 2 * 1/3 * bf * tf + 1/3 * (ht - 2 * tf) * t 3 =
3 3
98714.8 mm4
w
Iw = Iy * h2 / 4 = 6.965E+08 mm6
87460.2
X1 =  / Sx * √ [ E * G * J * A / 2 ] = MPa
0.0000067
X2 = 4 * [ Sx / (G * J) ]2 * Iw / Iy = mm2/N2
522076.5
Zx = tw * h 2 / 4 + ( bf - tw ) * ( ht - tf ) * tf = 104228.6 mm3
t 2 2
Zy = tf * bf / 2 + ( ht - 2 * tf ) * t / 4 = mm3
w
G = modulus geser, Zx = modulus penampang plastis thd. sb. x, J =
Konstanta puntir torsi, Zy = modulus penampang plastis thd. sb. y, Iw
= konstanta putir lengkung, X1 = koefisien momen tekuk torsi lateral,
h = tinggi bersih badan, X2 = koefisien momen tekuk torsi lateral,
2
KOLOM BIAXIAL BENDING
FAKTOR PANJANG TEKUK UNTUK PORTAL BERGOYANG (SMITH, 1996)
thd.sb. X :
Ic3 = 124000
Lc3 = 4500
Ib3 = 34800000 Ib4 = 34800000

Lb3 = 7000 B Lb4 = 7000 Joint B :
( Ic / Lc) = 55
Ic2 = 124000 ( Ib / Lb) = 9943
Lc2 = 4500 GBx =  ( Ic / L c ) /  ( Ib / L b ) = 0.0
Ib1 = 34800000 Ib2 = 34800000

Lb1 = 7000 A Lb2 = 7000 Joint A :
 ( Ic / Lc) =
Ic1 = 124000
 ( Ib / Lb) =
Lc1 = 4500
GAx =  ( Ic / L c ) /  ( Ib / L b ) =
3
55
9943
0.0
Faktor panjang tekuk efektif thd.sb. x,
kx = [ 3*GAx*GBx + 1.4*(GAx+ GBx) + 0.64 ] / [ 3*GAx*GBx + 2.0*(GAx+ GBx) + 1.28 ]
 kx = 0.50344
thd.sb. Y :
Ic3 = 17400000
Lc3 = 4500
Ib3 = 12500000 Ib4 = 12500000

Lb3 = 5000 B Lb4 = 5000 Joint B :
( Ic / Lc) = 7733
Ic2 = 17400000 ( Ib / Lb) = 5000
Lc2 = 4500 GBy =  ( Ic / L c ) /  ( Ib / L b ) = 1.5
Ib1 = 12500000 Ib2 = 12500000

Lb1 = 5000 A Lb2 = 5000 Joint A :
 ( Ic / Lc) =
Ic1 = 17400000
 ( Ib / Lb) =
Lc1 = 4500
GAy =  ( Ic / L c ) /  ( Ib / L b ) =
4
7733
5000
1.5
Faktor panjang tekuk efektif thd.sb. y,
ky = [ 3*GAy*GBy + 1.4*(GAy+ GBy) + 0.64 ] / [ 3*GAy*GBy + 2.0*(GAy+ GBy) + 1.28 ]
 kY = 0.82955
5
E. PERHITUNGAN KEKUATAN
1. TAHANAN AKSIAL TEKAN PENGARUH KELANGSINGAN KOLOM
Faktor tekuk kolom dihitung dengan rumus sebagai berikut :

a. Untuk nilai c  0.25 maka termasuk kolom pendek :
→ =1
b. Untuk nilai 0.25 < c ≤ 1.20 maka termasuk kolom sedang :
→  = 1.43 / ( 1.6 - 0.67 * c )
c. Untuk nilai c > 1.20 maka termasuk kolom langsing :
→  = 1.25 * c2
Menentukan parameter kelangsingan :

Faktor panjang tekuk efektif terhadap sumbu x, kx = 0.50
Faktor panjang tekuk efektif terhadap sumbu y, ky = 0.83
Panjang kolom terhadap sumbu x : Lx = 6000 mm
Panjang tekuk efektif terhadap sumbu x, Lkx = kx * Lx = 3021 mm
Panjang kolom terhadap sumbu y : Ly = 1500 mm
Panjang tekuk efektif terhadap sumbu y, Lky = ky * Ly = 1244 mm
Parameter kelangsingan terhadap sumbu x,
cx = 1 /  * Lkx /rx * √ ( fy / E ) = 0.2440
Parameter kelangsingan terhadap sumbu Y,
cy = 1 /  * Lky / ry * √ ( fy / E ) = 0.3518
Menentukan nilai faktor tekuk terhadap sumbu x
:
Untuk parameter kelangsingan terhadap sumbu x, cx = 0.2440
a. Kolom pendek : = 1.0000
b. Kolom sedang :  = 1.43 / ( 1.6 - 0.67 * c ) = 0.9955
c. Kolom langsing :  = 1.25 * c2 = -
Faktor tekuk terhadap sumbu x,  x = 1.0000
Menentukan nilai faktor tekuk terhadap sumbu y :
Untuk parameter kelangsingan terhadap sumbu y, cy = 0.3518
a. Kolom pendek : = -
b. Kolom sedang :  = 1.43 / ( 1.6 - 0.67 * c ) = 1.0482
c. Kolom langsing :  = 1.25 * c2 = -
Faktor tekuk terhadap sumbu y,  y = 1.0482
6
Tegangan tekuk :
Tegangan tekuk terhadap sumbu x, fcrx = fy / x = 240.000 MPa
Tegangan tekuk terhadap sumbu y, fcry = fy / y = 228.971 MPa
Tahanan aksial tekan :
Tahanan aksial tekan nominal thd.sb. x, Nnx = A * fcrx = 1122720 N
Tahanan aksial tekan nominal thd.sb. y, Nny = A * fcry = 1071128 N
Tahanan aksial tekan nominal terkecil, Nn = 1071128 N
2. TAHANAN AKSIAL TEKAN PENGARUH TEKUK LENTUR TORSI
Tahanan aksial nominal tekan pengaruh tekuk lentur torsi, harus dihitung dengan rumus :
Nn = A * fclt dengan,
fclt = [ ( fcry + fcrz) / ( 2 * H ) ] * [ 1 - 1 - 4* fcry* fcrz* H / ( fcry + fcrz)2] ]
Koordinat pusat geser terhadap titik berat penampang, xo = 0.00 mm

yo = 0.00 mm
Jari-jari girasi polar terhadap pusat geser,
ro2 = ( Ix + Iy ) / A + xo2 + yo2 = H mm
34
= 1 - [ ( xo2 + yo2 ) / ro2 ] =
1.00
Tegangan tekuk thd.sb. y (sumbu lemah), fcry = fy / y = MPa
228.971
fcrz = G * J / ( A * ro2 ) = 48396.700 MPa
Tegangan tekuk lentur torsi,
fclt = [ ( fcry + fcrz) / (2*H) ] * [ 1 -1 - 4* fcry* fcrz* H / ( fcry + fcrz)2] ] = 228.971 MPa
Tahanan aksial tekan nominal, Nn = A * fclt = 1071128 N
3. TAHANAN AKSIAL TEKAN
Tahanan aksial tekan nominal pengaruh kelangsingan kolom,

Nn = 1071128 N
Tahanan aksial tekan nominal pengaruh tekuk lentur torsi,
Nn = 1071128 N
Tahanan aksial tekan nominal (terkecil),  Nn = 1071128 N
Tahanan aksial tekan, n * Nn = 910459 N
7
4. MOMEN NOMINAL PENGARUH LOCAL BUCKLING PADA
Momen nominal penampang akibat pengaruh local buckling pada sayap untuk :
a. Penampang compact :   p
→ Mn = Mp
b. Penampang non-compact : p <   r
→ Mn = Mp - (Mp - Mr) * (  - p) / ( r - p)
c. Penampang langsing :  > r
→ Mn = Mr * ( r /  )2
Momen plastis thd.sb. x, Mpx = fy * Zx = 125298360 Nmm

Momen batas tekuk thd.sb. x, Mrx = Sx * ( fy - fr ) = 11509000 Nmm
Momen plastis thd.sb. y, Mpy = fy * Zy = 25014870 Nmm
Momen batas tekuk thd.sb. y, Mry = Sy * ( fy - fr ) = 81770000 Nmm
Kelangsingan penampang sayap,  = bf / tf = 16.667
Batas kelangsingan maksimum untuk penampang compact ,
p = 170 / √ fy =
10.973
Batas kelangsingan maksimum untuk penampang non-compact ,
r = 370 / √ ( fy - fr ) = 28.378
 > p dan  < r
Berdasarkan nilai kelangsingan sayap, maka termasuk penampang non-compact
Momen nominal thd.sb. x :
compact : Mnx = Mpx = - Nmm
non-compact : Mnx = Mpx - (Mpx - Mrx) * (  - p) / ( r - p) = 88076009 Nmm
langsing : Mnx = Mrx * ( r /  )2 = - Nmm
Momen nominal untuk penampang : non-compact Mnx = 88076009 Nmm
Momen nominal thd.sb. y :
compact : Mny = Mpy = - Nmm
non-compact : Mny = Mpy - (Mpy - Mry) * (  - p) / ( r - p) = 43580396 Nmm
langsing : Mny = Mry * ( r /  )2 = - Nmm
Momen nominal untuk penampang : non-compact Mny = 43580396 Nmm
8
5. MOMEN NOMINAL PENGARUH LOCAL BUKLING PADA
Kelangsingan penampang badan,  = h / tw = 44.769

Gaya aksial leleh, Ny = A * fy = 1122720 N
Nu / ( b * Ny ) = 0.108 N
a. Batas kelangsingan maksimum untuk penampang compact :
Untuk nilai, Nu / ( b * Ny ) ≤ 0.125
→ p = 1680 / √ fy * [ ( 1 - 2.75 * Nu / ( b * Ny ) ]
Untuk nilai, Nu / ( b * Ny ) > 0.125
→ p = 500 / √ fy * [ ( 2.33 - Nu / ( b * Ny ) ]  665 / √ fy
b. Batas kelangsingan maksimum untuk penampang non-compact :
→ r = 2550 / √ fy * [ ( 1 - 0.74 * Nu / ( b * Ny ) ]
Untuk nilai : Nu / ( b * Ny ) < 0.125

p = 1680 / √ fy * [ ( 1 - 2.75 * Nu / ( b * Ny ) ] = 76.303
p = 500 / √ fy * [ ( 2.33 - Nu / ( b * Ny ) ] = -
p = 665 / √ fy = -
Batas kelangsingan maksimum penampang compact , p = 76.303
Batas kelangsingan maksimum penampang non-compact ,
r = 2550 / √ fy * [ ( 1 - 0.74 * Nu / ( b * Ny ) ] = 151.474
 < p dan  < r
Berdasarkan nilai kelangsingan badan, maka termasuk penampang compact
Momen nominal thd.sb. x :
compact : Mnx = Mpx = 125298360 Nmm

non-compact : Mnx = Mpx - (Mpx - Mrx) * (  - p) / ( r - p) = - Nmm
langsing : Mnx = Mrx * ( r /  ) =2
- Nmm
Momen nominal thd.sb. x : penampang compact Mnx = 125298360 Nmm
Momen nominal thd.sb. y :
compact : Mny = Mpy = 25014870 Nmm

non-compact : Mny = Mpy - (Mpy - Mry) * (  - p) / ( r - p) = - Nmm
langsing : Mny = Mry * ( r /  )2 = - Nmm
Momen nominal thd.sb. y : penampang compact Mny = 25014870 Nmm
9
6. TAHANAN MOMEN
Momen nominal berdasarkan pengaruh local buckling pada sayap,

Momen nominal thd.sb. x, Mnx = 88076009 Nmm
Momen nominal thd.sb. y, Mny = 43580396 Nmm
Momen nominal berdasarkan pengaruh local buckling pada badan,
Momen nominal thd.sb. x, Mnx = 125298360 Nmm
Momen nominal thd.sb. y, Mny = 25014870 Nmm
Momen nominal (terkecil) yang menentukan,
Momen nominal thd.sb. x,  Mnx = 88076009 Nmm
Momen nominal thd.sb. y,  Mny = 25014870 Nmm
Tahanan momen lentur thd.sb. x, b * Mnx = 79268409 Nmm
Tahanan momen lentur thd.sb. y, b * Mny = 22513383 Nmm
7. INTERAKSI AKSIAL TEKAN DAN MOMEN LENTUR
Gaya aksial akibat beban terfaktor, Nu = 108900 N

Momen akibat beban terfaktor thd.sb. x, Mux = 16621966 Nmm
Momen akibat beban terfaktor thd.sb. y, Muy = 9785360 Nmm
Tahanan aksial tekan, n * Nn = 910459 N
Tahanan momen lentur thd.sb. x, b * Mnx = 79268409 Nmm
Tahanan momen lentur thd.sb. y, b * Mny = 22513383 Nmm
Kolom yang menahan gaya aksial tekan dan momen lentur harus memenuhi
persamaan interaksi aksial tekan dan momen lentur sbb :
Untuk nilai, Nu / ( n * Nn ) > 0.20
→ Nu / ( n * Nn ) + 8 / 9 * [ Mux / ( b * Mnx ) + Muy / ( b * Mny )]  1.0
Untuk nilai, Nu / (  * Nn ) ≤ 0.20
→ Nu / ( 2 * n * Nn ) + [ Mux / ( b * Mnx ) + Muy / ( b * Mny ) ]  1.0
Untuk nilai : Nu / ( n * Nn ) = 0.1196 < 0.20

Nu / ( n * Nn ) + 8/9*[ Mux / ( b * Mnx ) + Muy / ( b * Mny ) ] = -
Nu / ( 2 * n * Nn ) + [ Mux / ( b * Mnx ) + Muy / ( b * Mny ) ] = 0.7041
Nilai interaksi aksial tekan dan momen lentur = 0.7041
0.7041 < 1.  AMAN (OK)
1
8. TAHANAN
Ketebalan plat badan tanpa pengaku harus memenuhi syarat,

h2 / tw  6.36 *  ( E / fy )
39.38462 < 183.60  Plat badan memenuhi syarat (OK)
Kontrol tahanan geser nominal plat badan tanpa pengaku :

Gaya geser akibat beban terfaktor, Vu = 207000 N
Luas penampang badan, Aw = tw * ht = 1950 mm2
Tahanan gaya geser nominal, Vn = 0.60 * fy * Aw = 280800 N
Tahanan gaya geser,  f * Vn = 210600 N
Syarat yg harus dipenuhi : Vu  f * Vn
207000 < 210600  AMAN (OK)
Vu / ( f * Vn ) = < 1.0 (OK)

0.9829
9. INTERAKSI GESER DAN LENTUR
Elemen yang memikul kombinasi geser dan lentur harus dilakukan kontrol sbb. :
Sayarat yang harus dipenuhi untuk interakasi geser dan lentur :
Mux / ( b * Mnx ) + Muy / ( b * Mny ) + 0.625 * Vu / ( f * Vn )  1.375
Mux / ( b * Mnx ) = 0.2097

Muy / ( b * Mny ) = 0.4346
Vu / ( f * Vn ) = 0.9829
Mux / ( b * Mnx ) + Muy / ( b * Mny ) + 0.625* Vu / ( f * Vn ) = 1.2587
1.2587 < 1.375 AMAN (OK)
1
PERHITUNGAN BALOK B5
A. DATA BAHAN

fy = 240 MPa
Tegangan sisa (residual stress ), fr = 70 MPa
Modulus elastik baja (modulus of elasticity ), E= 200000 MPa
Angka Poisson (Poisson's ratio ), = 0.3
B. DATA PROFIL BAJA

Profil : WF (300x150x6/5x9)
ht = 300 mm
tf bf = 150 mm
tw = 6.5 mm
tf = 9 mm
tw r= 13
h h2 ht A= 4678
mm
mm2
Ix = 124000 mm4
Iy = 32900 mm4
rx = 136.5
r mm
h1 ry = 39
mm
Sx = 67700
bf Sy = 481000
mm3
mm3
w= 360.027
Berat : N/m
BALOK TANPA PENGAKU BADAN
Page
C. DATA BALOK
Panjang elemen thd.sb. x, Lx = 6000 mm

Panjang elemen thd.sb. y ( jarak dukungan lateral ), Ly = 1500 mm
Momen maksimum akibat beban terfaktor, Mu = 9313.847156 Nmm
Momen pada 1/4 bentang, MA = 1229.058319 Nmm
Momen di tengah bentang, MB = 5029.411998 Nmm
Momen pada 3/4 bentang, MC = 925.7120132
Nmm
Gaya geser akibat beban terfaktor, Faktor Vu = 9807.350847
N
reduksi kekuatan untuk lentur, Faktor b = 0.90
G = E / [ 2 *( 1 +  ) ] = 76923 MPa
h1 = tf + r = 22.00 mm
h2 = ht - 2 * h1 = 256.00 mm
h = ht - tf = 291.00 mm
J =  [ b * t /3 ] = 2 * 1/3 * bf * tf3 + 1/3 * (ht - 2 * tf) * 3
3
98714.8 mm4
w =
t 6.965E+08
Iw = Iy * h2 / 4 = 87460.2 mm6
X1 =  / Sx * √ [ E * G * J * A / 2 ] = 0.0000067
MPa
522076.5
X2 = 4 * [ Sx / (G * J) ]2 * Iw / Iy = mm2/N2
104228.6
Zx = tw * h 2 / 4 + ( bf - tw ) * ( ht - tf ) * tf mm3
t
=
Z =t *b2/2+(h -2*t )*t 2/4= mm3
y f f t f w
G = modulus geser, tf
J = Konstanta puntir torsi,
Iw = konstanta putir lengkung, tw
h h2 ht
X1 = koefisien momen tekuk torsi lateral - 1,
r
h1
Zx = modulus penampang plastis thd. sb. x, bf
Zy = modulus penampang plastis thd. sb. y,
Page
1. MOMEN NOMINAL PENGARUH LOCAL BUCKLING

p = 170 / √ fy = 10.973
r = 370 / √ ( fy - fr ) = 28.378
Momen plastis, Mp = fy * Zx = 125298360 Nmm
Momen batas tekuk, Mr = Sx * ( fy - fr ) = 11509000 Nmm
Momen nominal penampang untuk :
→ Mn = Mp
→ Mn = Mp - (Mp - Mr) * (  - p) / ( r - p)
→ M n = M r * ( r /  ) 2
 > p dan  < r

Momen nominal penampang dihitung sebagai berikut :
compact : Mn = Mp = - Nmm
non-compact : Mn = Mp - (Mp - Mr) * (  - p) / ( r - p) = 88076009 Nmm

langsing : M n = M r * ( r /  ) 2 = - Nmm
Momen nominal untuk penampang : non-compact Mn = 88076009 Nmm
Page
2. MOMEN NOMINAL BALOK PLAT BERDINDING PENUH

Untuk penampang yang mempunyai ukuran : h / tw > r
maka momen nominal komponen struktur, harus dihitung dengan rumus :
Mn = Kg * S * fcr
dengan, Kg = 1 - [ ar / (1200 + 300 * ar) ] * [ h / tw - 2550 /  fcr ]
a. Untuk kelangsingan : G ≤ p → fcr = fy
b. Untuk kelangsingan : p < G ≤ r
→ fcr = Cb * fy * [ 1 - ( G - p ) / ( 2 * ( r - p ) ) ] ≤ fy
c. Untuk kelangsingan : G > r → fcr = fc * ( r / G )2 ≤ fy
Untuk tekuk torsi lateral : → fc = C b * fy / 2 ≤ fy
Untuk tekuk lokal : → fc = fy / 2
Koefisien momen tekuk torsi lateral,
Cb = 12.5 * Mu / ( 2.5 * Mu + 3 * MA + 4 * MB + 3 * MC ) = 2.33 > 2.3
 diambil, Cb = 2.30
Perbandingan luas plat badan terhadap luas plat sayap,
ar = h * tw / ( bf * tf ) = 1.401
Momen inersia, I1 = Iy / 2 - 1/12 * t w3 * 1/3 * h2 = 14497 mm4
Luas penampang, A1 = A / 2 - 1/3 * tw * h2 = 1784 mm2
Jari-jari girasi daerah plat sayap ditambah sepertiga bagian plat badan yang mengalami
tekan, r1 =  ( I1 / A1 ) = 3 mm
Page
2.1. Momen nominal berdasarkan tekuk torsi lateral
Jarak antara pengekang lateral, L = Ly = 1500 mm

Angka kelangsingan, G = L / r1 = 526.246
p = 1.76 * √ ( E / fy ) = 50.807
r = 4.40 * √ ( E / fy ) = 127.017
Tegangan acuan untuk momen kritis tekuk torsi lateral,
fc = C b * fy / 2 = 276.00 MPa
fc > fy maka diambil, fc = 240.00 MPa
G > p dan G > r

Tegangan kritis penampang dihitung sebagai berikut :
G ≤ p fcr = fy = - MPa
p ≤ G ≤ r fcr = Cb* fy* [ 1 - ( G - p) / ( 2*( r - p) ) ] = -1187.48 MPa

G > r fcr = fc * ( r / G )2 = 13.98 MPa
fcr = 13.98 MPa
fcr < fy maka diambil, fcr = 13.98 MPa
Modulus penampang elastis, S = Sx = 67700 mm3
Koefisien balok plat berdinding penuh,
Kg = 1 - [ ar / (1200 + 300 * ar) ] * [ h / tw - 2550 /  fcr ] = 1.551
Momen nominal penampang, Mn = Kg * S * fcr = 1468097 Nmm
Page
2.2. Momen nominal berdasarkan local buckling pada sayap
Faktor kelangsingan plat badan, ke = 4 /  ( h / tw ) = < 0.763

0.598
diambil, ke =
0.598
Kelangsingan penampang sayap, G = bf / ( 2 * tf ) =
8.33
p = 0.38 * √ ( E / fy ) = 10.97
r = 1.35 * √ ( ke * E / fy ) = 30.13
Tegangan acuan untuk momen kritis tekuk lokal, fc = fy / 2 = 120.00 MPa
G < p dan G < r

Berdasarkan nilai kelangsingan sayap, maka termasuk penampang compact
G ≤ p fcr = fy = 240.00 MPa
p ≤ G ≤ r fcr = Cb* fy* [ 1 - ( G - p) / ( 2*( r - p) ) ] = - MPa

G > r fcr = fc * ( r / G )2 = - MPa
Tegangan kritis penampang, fcr = 240.00 MPa
Kg = 1 - [ ar / (1200 + 300 * ar) ] * [ h / tw - 2550 /  fcr ] = 1.104
Page
3. MOMEN NOMINAL PENGARUH LATERAL BUCKLING
Momen nominal komponen struktur dengan pengaruh tekuk lateral, untuk :

a. Bentang pendek : L  Lp
→ Mn = Mp = fy * Zx
b. Bentang sedang : Lp < L  Lr
→ Mn = Cb * [ Mr + ( Mp - Mr ) * ( Lr - L ) / ( Lr - Lp ) ]  Mp
c. Bentang panjang : L > Lr
→ Mn = Cb *  / L*√ [ E * Iy * G * J + (  * E / L )2 * Iy * Iw ]  Mp
Panjang bentang maksimum balok yang mampu menahan momen plastis,

Lp = 1.76 * ry * √ ( E / fy ) = 1981 mm
fL = fy - fr = 170 MPa
Panjang bentang minimum balok yang tahanannya ditentukan oleh momen kritis tekuk torsi
lateral, Lr = ry * X1 / fL * √ [ 1 + √ ( 1 + X2 * f 2 ) ] = 2902 mm
L
Cb = 12.5 * Mu / ( 2.5*Mu + 3*MA + 4*MB + 3*MC ) = 2.33
Panjang bentang thd.sb. y (jarak dukungan lateral), L = Ly = 1500 mm
L < Lp dan L < Lr
 Termasuk kategori : bentang pendek
Momen nominal dihitung sebagai berikut :
Mn = Mp = fy * Zx = 125298360 Nmm
Mn = Cb * [ Mr + ( Mp - Mr ) * ( Lr - L ) / ( L - Lp ) ] = - Nmm
r Nmm
Mn = Cb *  / L*√ [ E * I * G * J + (  * E / L ) * I * Iw ] =
2
- Nmm
y Mn y > Mp
Momen nominal yang digunakan,  Mn = 12529836 Nmm
Page
4. TAHANAN MOMEN LENTUR
a.
Momen nominal berdasarkan pengaruh local buckling , Mn = Nmm
b.
125298360
Momen nominal balok plat berdinding penuh :
Momen nominal berdasarkan tekuk torsi lateral, Mn = 1468097 Nmm
Momen nominal berdasarkan local buckling pd. sayap, Mn = 17931616 Nmm
c.
Momen nominal berdasarkan pengaruh lateral buckling , Mn = 125298360 Nmm
Momen nominal (terkecil) yang menentukan,  Mn = 1468097 Nmm
Tahanan momen lentur, b * Mn = 1321287 Nmm
Momen akibat beban terfaktor, Mu = 9313.847156 Nmm
Syarat yg harus dipenuhi : Mu  b * Mn
9314 < 1321287  AMAN (OK)
Mu / ( b * Mn ) = < 1.0 (OK)

0.0070
5. TAHANAN GESER
Kontrol tahanan geser nominal plat badan tanpa pengaku : Ketebalan plat
badan tanpa pengaku harus memenuhi syarat,
h2 / tw  6.36 *  ( E / fy )
39.38462 < 183.60  Plat badan memenuhi syarat (OK)
Gaya geser akibat beban terfaktor, Vu = 9807.350847 N

Tahanan gaya geser, f * Vn = 252720 N
9807.35085 < 252720  AMAN (OK)
Vu / ( f * Vn ) = < 1.0 (OK)

0.9000
Page
Syarat yang harus dipenuhi untuk interaksi geser dan lentur :
Mu / ( b * Mn ) + 0.625 * Vu / ( f * Vn )  1.375
Mu / ( b * Mn ) = 0.0070
Vu / ( f * Vn ) = 0.0388
Mu / ( b * Mn ) + 0.625 * Vu / ( f * Vn ) = 0.0313
< 1.375 AMAN (OK)
Page
PERHITUNGAN BALOK B6
A. DATA BAHAN

fy = 240 MPa
Tegangan sisa (residual stress ), fr = 70 MPa
Modulus elastik baja (modulus of elasticity ), E= 200000 MPa
Angka Poisson (Poisson's ratio ), = 0.3
B. DATA PROFIL BAJA

Profil : WF (250x125x9x16)
ht = 250 mm
tf bf = 125 mm
tw = 16 mm
tf = 9 mm
tw r= 12
h h2 ht A= 376600
mm
mm2
Ix = 40500000 mm4
Iy = 2940000 mm4
rx = 104
r mm
h1 ry = 27.9
mm
Sx = 324000
bf Sy = 47000
mm3
mm3
w= 288.31551
Berat : N/m
BALOK TANPA PENGAKU BADAN
Page
C. DATA BALOK
Panjang elemen thd.sb. x, Lx = 6000 mm

Panjang elemen thd.sb. y ( jarak dukungan lateral ), Ly = 0 mm
Momen maksimum akibat beban terfaktor, Mu = 244.4676728 Nmm
Momen pada 1/4 bentang, MA = 277539 Nmm
Momen di tengah bentang, MB = 2762827 Nmm
Momen pada 3/4 bentang, MC = 802954
Nmm
Gaya geser akibat beban terfaktor, Faktor Vu = 507466.5
N
reduksi kekuatan untuk lentur, Faktor b = 0.90
G = E / [ 2 *( 1 +  ) ] = 76923 MPa
h1 = tf + r = 21.00 mm
h2 = ht - 2 * h1 = 208.00 mm
h = ht - tf = 241.00 mm
J =  [ b * t /3 ] = 2 * 1/3 * bf * tf3 + 1/3 * (ht - 2 * tf) * 3
3
377507.3 mm4
w =
t 4.269E+10
Iw = Iy * h2 / 4 = 320653.5 mm6
X1 =  / Sx * √ [ E * G * J * A / 2 ] = 0.0000072
MPa
486421.0
X2 = 4 * [ Sx / (G * J) ]2 * Iw / Iy = mm2/N2
85160.5
Zx = tw * h 2 / 4 + ( bf - tw ) * ( ht - tf ) * tf mm3
t
=
Z =t *b2/2+(h -2*t )*t 2/4= mm3
y f f t f w
G = modulus geser, tf
J = Konstanta puntir torsi,
Iw = konstanta putir lengkung, tw
h h2 ht
r
h1
Zx = modulus penampang plastis thd. sb. x, bf
Zy = modulus penampang plastis thd. sb. y,
Page
1. MOMEN NOMINAL PENGARUH LOCAL BUCKLING

p = 170 / √ fy = 10.973
r = 370 / √ ( fy - fr ) = 28.378
Momen nominal penampang untuk :
→ Mn = Mp
→ Mn = Mp - (Mp - Mr) * (  - p) / ( r - p)
→ M n = M r * ( r /  ) 2
 > p dan  < r

Momen nominal penampang dihitung sebagai berikut :
compact : Mn = Mp = - Nmm
non-compact : Mn = Mp - (Mp - Mr) * (  - p) / ( r - p) = 106412023 Nmm

langsing : M n = M r * ( r /  ) 2 = - Nmm
Momen nominal untuk penampang : non-compact Mn = 106412023 Nmm
Page
2. MOMEN NOMINAL BALOK PLAT BERDINDING PENUH

Untuk penampang yang mempunyai ukuran : h / tw < r
maka momen nominal komponen struktur, tidak harus dihitung dengan rumus :
Mn = Kg * S * fcr
dengan, Kg = 1 - [ ar / (1200 + 300 * ar) ] * [ h / tw - 2550 /  fcr ]
a. Untuk kelangsingan : G ≤ p → fcr = fy
b. Untuk kelangsingan : p < G ≤ r
→ fcr = Cb * fy * [ 1 - ( G - p ) / ( 2 * ( r - p ) ) ] ≤ fy
c. Untuk kelangsingan : G > r → fcr = fc * ( r / G )2 ≤ fy
Untuk tekuk torsi lateral : → fc = C b * fy / 2 ≤ fy
Untuk tekuk lokal : → fc = fy / 2
Cb = 12.5 * Mu / ( 2.5 * Mu + 3 * MA + 4 * MB + 3 * MC ) = 0.00 < 2.3
 diambil, Cb = 0.00
Perbandingan luas plat badan terhadap luas plat sayap,
ar = h * tw / ( bf * tf ) = 3.428
Momen inersia, I1 = Iy / 2 - 1/12 * t w3 * 1/3 * h2 = 1446334 mm4
Luas penampang, A1 = A / 2 - 1/3 * tw * h2 = 187191 mm2
Jari-jari girasi daerah plat sayap ditambah sepertiga bagian plat badan yang mengalami
tekan, r1 =  ( I1 / A1 ) = 3 mm
Page
2.1. Momen nominal berdasarkan tekuk torsi lateral
Jarak antara pengekang lateral, L = Ly = 0 mm

Angka kelangsingan,  G = L / r1 = 0.000

p = 1.76 * √ ( E / fy ) = 50.807
r = 4.40 * √ ( E / fy ) = 127.017
Tegangan acuan untuk momen kritis tekuk torsi lateral,
fc = C b * fy / 2 = 0.03 MPa
fc < fy maka diambil, fc = 0.03 MPa
G < p dan G < r

G ≤ p fcr = fy = 240.00 MPa
G > r fcr = fc * ( r / G )2 = - MPa
fcr = 240.00 MPa
Kg = 1 - [ ar / (1200 + 300 * ar) ] * [ h / tw - 2550 /  fcr ] = 1.230
Page
2.2. Momen nominal berdasarkan local buckling pada sayap
Faktor kelangsingan plat badan, ke = 4 /  ( h / tw ) = > 0.763

1.031
diambil, ke =
0.763
Kelangsingan penampang sayap, G = bf / ( 2 * tf ) =
6.94
p = 0.38 * √ ( E / fy ) = 10.97
r = 1.35 * √ ( ke * E / fy ) = 34.04
Tegangan acuan untuk momen kritis tekuk lokal, fc = fy / 2 = 120.00 MPa
G < p dan G < r

Berdasarkan nilai kelangsingan sayap, maka termasuk penampang compact
G ≤ p fcr = fy = 240.00 MPa

G > r fcr = fc * ( r / G )2 = - MPa
Tegangan kritis penampang, fcr = 240.00 MPa
Kg = 1 - [ ar / (1200 + 300 * ar) ] * [ h / tw - 2550 /  fcr ] = 1.230
Page
3. MOMEN NOMINAL PENGARUH LATERAL BUCKLING
Momen nominal komponen struktur dengan pengaruh tekuk lateral, untuk :

a. Bentang pendek : L  Lp
→ Mn = Mp = fy * Zx
b. Bentang sedang : Lp < L  Lr
→ Mn = Cb * [ Mr + ( Mp - Mr ) * ( Lr - L ) / ( Lr - Lp ) ]  Mp
c. Bentang panjang : L > Lr
→ Mn = Cb *  / L*√ [ E * Iy * G * J + (  * E / L )2 * Iy * Iw ]  Mp
Panjang bentang maksimum balok yang mampu menahan momen plastis,

Lp = 1.76 * ry * √ ( E / fy ) = 1418 mm
fL = fy - fr = 170 MPa
Panjang bentang minimum balok yang tahanannya ditentukan oleh momen kritis tekuk torsi
lateral, Lr = ry * X1 / fL * √ [ 1 + √ ( 1 + X2 * f 2 ) ] = 7625 mm
L
Cb = 12.5 * Mu / ( 2.5*Mu + 3*MA + 4*MB + 3*MC ) = 0.00
Panjang bentang thd.sb. y (jarak dukungan lateral), L = Ly = 0 mm
L < Lp dan L < Lr
 Termasuk kategori : bentang pendek
Momen nominal dihitung sebagai berikut :
Mn = Mp = fy * Zx = 116741040 Nmm
Mn = Cb * [ Mr + ( Mp - Mr ) * ( Lr - L ) / ( L - Lp ) ] = - Nmm
r Nmm
Mn = Cb *  / L*√ [ E * I * G * J + (  * E / L ) * I * Iw ] =
2
- Nmm
y Mn y > Mp
Momen nominal yang digunakan,  Mn = 11674104 Nmm
Page
4. TAHANAN MOMEN LENTUR
a.
Momen nominal berdasarkan pengaruh local buckling , Mn = Nmm
b.
116741040
Momen nominal balok plat berdinding penuh :
Momen nominal berdasarkan tekuk torsi lateral, Mn = 95646646 Nmm
Momen nominal berdasarkan local buckling pd. sayap, Mn = 95646646 Nmm
c.
Momen nominal berdasarkan pengaruh lateral buckling , Mn = 116741040 Nmm
Momen nominal (terkecil) yang menentukan,  Mn = 95646646 Nmm
Tahanan momen lentur, b * Mn = 86081981 Nmm
Momen akibat beban terfaktor, Mu = 244.4676728 Nmm
Syarat yg harus dipenuhi : Mu  b * Mn
24 < 86081981  AMAN (OK)
Mu / ( b * Mn ) = < 1.0 (OK)

0.0000
5. TAHANAN GESER
Kontrol tahanan geser nominal plat badan tanpa pengaku : Ketebalan plat
badan tanpa pengaku harus memenuhi syarat,
h2 / tw  6.36 *  ( E / fy )
1 < 183.60  Plat badan memenuhi syarat (OK)
Gaya geser akibat beban terfaktor, Vu = 507466.5 N

Tahanan gaya geser, f * Vn = 518400 N
507466.5 < 518400  AMAN (OK)
Vu / ( f * Vn ) = < 1.0 (OK)

0.9000
Page
Syarat yang harus dipenuhi untuk interaksi geser dan lentur :
Mu / ( b * Mn ) + 0.625 * Vu / ( f * Vn )  1.375
Mu / ( b * Mn ) = 0.0000
Vu / ( f * Vn ) = 0.9789
Mu / ( b * Mn ) + 0.625 * Vu / ( f * Vn ) = 0.6118
< 1.375 AMAN (OK)
Page
CV. GEOTEKNIK
KUSUMAH
CONSULTANT & SOIL
CONE PENETROMETER TEST

PROJEC : Pembangunan Café Gn.Walat DEPT : - 2.60 dari
: Jl. Pahlawan, Batununggal,
LOCATION : Kec. Cibadak, GROUND SURFACE LEVEL : 0.0 dari Jalan
: Kab. Sukabumi, Jawa Barat 43351 GROUND WATER LEVEL : - dari GSL
SOUNDING No. : S-1 OPERATOR : Lutfi
DATE OF TESTED : 12 September 2022 ENGINEER : Rifaldi Yusuf,S.T.
Manometer Reading Cone Local Friction Soil Clasification
Depth Cone Total Resistance Friction TCF Ratio Prediction from Program
Cw Tw qc fs Rf or
(m) (kg/cm2) (kg/cm2) (kg/cm2) (kg/cm2) (kg/cm) (%) Manual
0.00 0 0 0 0 0 0
-0.20 2 5 2 0.20 3.95 9.88 Organic clays & mixed
soils
soils
-0.60 4 7 4 0.20 11.85 4.94 Inorganic clay soft
soils
soils
soils
soils
-1.60 7 12 7 0.33 46.10 4.70 Inorganic clay medium
soils
-2.00 8 14 8 0.40 61.90 4.94 Inorganic clay medium
-2.20 100 130 100 1.98 101.42 1.98 Moderate sands
-2.40 130 150 130 1.32 127.76 1.01 Dense or cemented sands
-2.80 170 >150
CV. GEOTEKNIK
KUSUMAH
CONSULTANT & SOIL

PROJEC : Pembangunan Café Gn.Walat DEP : - 2.20 dari
LOCATION
: Kec. Cibadak, GROUND SURFACE LEVEL : 0.0 dari Jalan
SOUNDING No.
: S-2 OPERATOR : Lutfi
DATE OF TESTED : 12 September 2022 ENGINEER : Rifaldi Yusuf, S..T.
Cw Tw qc fs Rf or
0.00 0 0 0 0 0 0
-0.20 2 5 2 0.20 3.95 9.88 Organic clays & mixed soils
-1.60 100 120 100 1.32 68.49 1.32 Moderate sands
-2.40 170 >150
CV. GEOTEKNIK
KUSUMAH
CONSULTANT & SOIL

PROJEC : Pembangunan Café Gn.Walat DEP : - 2.20 dari
LOCATION : Kec. Cibadak, GROUND SURFACE LEVEL : 0.0 dari Jalan
SOUNDING No. : S-3 OPERATOR : Lutfi
DATE OF TESTED : 12 September 2022 ENGINEER : Rifaldi Yusuf, S.T.
Cw Tw qc fs Rf or
0.00 0 0 0 0 0 0
-0.60 4 7 4 0.20 11.85 4.94 Inorganic clay soft
-1.40 12 22 12 0.66 43.46 5.49 Inorganic clay stiff
-1.60 90 120 90 1.98 82.98 2.20 Clayey-sands and silts
-2.40 170 >150
Parameter tanah Rencana Pembangunan Cafe, Perumahan Gunung
Walat Green Hill, Jl. Pahlawan, Batununggal, Kec. Cibadak,
Kabupaten Sukabumi, Jawa Barat 43351
Titik sondir 1
Depth v' Dr ø Cu M E G OCR mv CBR
m t/m2 % o kg/cm2 kg/cm2 kg/cm2 kg/cm2 cm2/kg %
0.20 0.12 - - 0.14 5.00 10.00 - 5.1 0.200 0.87

0.40 0.24 - - 0.21 7.50 15.00 - 3.3 0.133 1.35
0.60 0.36 - - 0.29 14.00 20.00 - 2.8 0.071 1.84
0.80 0.48 - - 0.28 12.50 25.00 - 1.9 0.080 2.35
1.00 0.60 - - 0.28 12.50 25.00 - 1.5 0.080 2.35
1.20 0.72 - - 0.33 15.00 30.00 - 1.5 0.067 2.87
1.40 0.84 - - 0.28 12.50 25.00 - 1.1 0.080 2.35
1.60 0.96 - - 0.39 24.50 35.00 - 1.3 0.041 3.39
1.80 1.08 - - 0.39 17.50 35.00 - 1.2 0.057 3.39
2.00 1.20 - - 0.44 44.00 40.00 - 1.2 0.023 3.92
2.20 1.40 95.2 48.0 - 381.18 250.00 19.59 - 0.003 33.33
2.40 1.62 100.6 48.0 - 523.16 325.00 25.78 - 0.002 43.33
2.60 1.84 102.9 48.0 - 617.55 375.00 31.42 - 0.002 50.00
Titik sondir 2
0.20 0.12 - - 0.14 5.00 10.00 - 5.1 0.200 0.87

0.40 0.24 - - 0.21 7.50 15.00 - 3.3 0.133 1.35
0.60 0.36 - - 0.21 7.50 15.00 - 2.0 0.133 1.35
0.80 0.48 - - 0.29 10.00 20.00 - 2.0 0.100 1.84
1.00 0.60 - - 0.29 10.00 20.00 - 1.5 0.100 1.84
1.20 0.72 - - 0.28 12.50 25.00 - 1.2 0.080 2.35
1.40 0.84 - - 0.56 25.00 50.00 - 2.2 0.040 5.00
1.60 1.04 99.4 48.0 - 397.76 250.00 14.55 - 0.003 33.33
1.80 1.26 104.2 48.0 - 542.34 325.00 20.05 - 0.002 43.33
2.00 1.48 104.0 48.0 - 583.00 350.00 24.41 - 0.002 46.67
2.20 1.70 104.0 48.0 - 624.59 375.00 29.03 - 0.002 50.00
Titik sondir 3
0.20 0.12 - - 0.14 5.00 10.00 - 5.1 0.200 0.87

0.40 0.24 - - 0.14 5.00 10.00 - 2.0 0.200 0.87
0.60 0.36 - - 0.29 14.00 20.00 - 2.8 0.071 1.84
0.80 0.48 - - 0.29 10.00 20.00 - 2.0 0.100 1.84
1.00 0.60 - - 0.28 12.50 25.00 - 1.5 0.080 2.35
1.20 0.72 - - 0.28 12.50 25.00 - 1.2 0.080 2.35
1.40 0.82 - - 0.67 66.00 60.00 - 2.9 0.015 6.10
1.60 1.01 96.8 48.0 - 348.79 225.00 13.37 - 0.003 30.00
1.80 1.23 99.8 48.0 - 438.97 275.00 18.06 - 0.002 36.67
2.00 1.45 102.2 48.0 - 531.54 325.00 23.08 - 0.002 43.33
2.20 1.67 104.3 48.0 - 626.18 375.00 28.52 - 0.002 50.00

Report Gunung Walat

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Report Gunung Walat

Uploaded by

Copyright:

Available Formats

LAPORAN ANALISIS STRUKTUR

CAFE DAN RESTORAN GUNUNG WALAT

1.1 Story Data 6

3.1 Joint Assignments 17

4.1 Load Patterns 28

5.1 Structure Results 38

1.1 Story Data

1.2 Grid Data

Table 1.2 - Grid Definitions - General

Table 1.3 - Grid Definitions - Grid Lines

G1 3.5 Start Yes

1.3 Point Coordinates

1.4 Line Connectivity

Table 1.5 - Column Bays

Label PointBayI PointBayJ IEndStory

Table 1.6 - Beam Bays

Label PointBayI PointBayJ

Table 1.7 - Brace Bays

Label PointBayI PointBayJ IEndStory

1.5 Area Connectivity

Table 1.8 - Floor Bays

Table 1.10 - Mass Summary by Story

Table 1.11 - Mass Summary by Group

Table 1.12 - Group Definitions

2.2 Frame Sections

Table 2.2 - Frame Section Property Definitions - Summary (Part 1 of 3)

Table 2.2 - Frame Section Property Definitions - Summary (Part 2 of 3)

Table 2.2 - Frame Section Property Definitions - Summary (Part 3 of 3)

2.3 Shell Sections

Table 2.3 - Area Section Property Definitions - Summary

2.4 Reinforcement Sizes

Table 2.4 - Reinforcing Bar Sizes

Table 2.5 - Link Property Definitions - Summary

2.6 Tendon Sections

Table 2.6 - Tendon Section Properties

3.1 Joint Assignments

Lantai 3 50 93 From Area

Lantai 25114From Area

3.2 Frame Assignments

Ringbalk B49 228 Beam Balok B6 WF

Ringbalk B55 232 Beam Balok B6 WF

Ringbalk B57 75 Beam Balok B6 WF

Ringbalk B59 236 Beam Balok B6 WF

Ringbalk B61 240 Beam Balok B6 WF

Ringbalk B66 217 Beam Balok B6 WF

Ringbalk B67 218 Beam Balok B6 WF

Ringbalk B68 219 Beam Balok B6 WF

Ringbalk B69 220 Beam Balok B6 WF

Ringbalk B70 221 Beam Balok B6 WF

Ringbalk B71 222 Beam Balok B6 WF

Ringbalk B73 230 Beam Balok B6 WF

Ringbalk B74 231 Beam Balok B6 WF

Ringbalk B76 73 Beam Balok B6 WF

Ringbalk B77 74 Beam Balok B6 WF

Ringbalk B79 234 Beam Balok B6 WF

Lantai 3 B59 194 Beam Balok B5 WF

Lantai 3 B61 198 Beam Balok B5 WF

Lantai 3 B63 211 Beam Balok B5 WF

Lantai 3 B64 212 Beam Balok B5 WF

Lantai 3 B65 213 Beam Balok B5 WF

Lantai 3 B66 199 Beam Balok B5 WF

Lantai 3 B67 200 Beam Balok B5 WF

Lantai 3 B68 201 Beam Balok B5 WF