Professional Documents
Culture Documents
Nemo Outdoor 9.21 Device Configuration Guide
Nemo Outdoor 9.21 Device Configuration Guide
2
Nemo Outdoor Device Configuration Guide
3
Nemo Outdoor
Device Configuration Guide
Table of Contents
1 Introduction ................................................................................................................................................... 7
1.1 Device autodetection ....................................................................................................... 8
1.2 Manual configuration of data connection ........................................................................ 8
1.3 Adding devices with NATA using ADB forwarding ......................................................... 12
1.4 Adding devices with NATA using tethering ................................................................... 15
1.5 Adding non-rooted devices ........................................................................................... 19
1.6 Using devices with Nemo Intelligent Device Interface and Nemo Device Interface
(NIDI/NDI) ................................................................................................................................. 21
1.7 Using devices with Nemo Diagnostic Module (NDM) .................................................... 22
1.8 Disabling driver signature verification on 64-Bit Windows 8.1 or 10 ............................ 23
2 Apple iPhone 6, 6S, 7, 8 ..........................................................................................................................26
3 Bandrich BandLuxe C320 .......................................................................................................................28
4 Bittium Tough Mobile...............................................................................................................................30
5 Blackberry Torch 9810 ............................................................................................................................32
6 Cellient R40 .................................................................................................................................................35
6.1 Setting up the packet data connection (Windows Mobile Broadband Connection)...... 38
7 Datang DTM8101/DTM8120/LeadCore LC8130e .........................................................................39
8 Essential Phone PH-1 ..............................................................................................................................41
9 Exelonix..........................................................................................................................................................42
10 Google Pixel, Pixel 3 .................................................................................................................................43
11 HTC U11 ........................................................................................................................................................44
12 HTC U12+ .....................................................................................................................................................45
13 Huawei P9 ....................................................................................................................................................48
14 Huawei E398................................................................................................................................................49
14.1 Changing TCP/IP Properties .......................................................................................... 49
15 Huawei Mate 20X, Mate 30 5G, Mate 30 Pro, Mate 30 Pro 5G, P40, P40 Pro ................... 51
15.1 Connecting Huawei P40 (ANA-NX9) with Nemo Invex II UIC ........................................ 53
16 Kodiak PTT....................................................................................................................................................54
16.1 Driver installation ........................................................................................................... 54
16.2 Pairing the phone with the laptop ................................................................................. 56
16.3 Configure and connect Kodiak PTT client via Bluetooth ............................................... 58
16.4 Adding Kodiak PTT device in Nemo Outdoor ................................................................. 60
17 LG G4, G6......................................................................................................................................................62
18 Lierda NB-IoT USB Dongles ..................................................................................................................63
19 Longsung KnowYou (KDC-5737 rel13) .............................................................................................64
20 Longsung KnowYou (KDC-6336 rel14) .............................................................................................65
21 Motorola Edge+, Edge 20 Pro, Edge 30 Pro ....................................................................................66
4
Nemo Outdoor Device Configuration Guide
5
Nemo Outdoor Device Configuration Guide
6
Nemo Outdoor Device Configuration Guide
1 Introduction
The purpose of this document is to give step-by-step instructions for setting up test devices for
data testing with Nemo tools.
Note that the devices below have been removed from the current document.
Configuration instructions for these devices can be found in the Device Configuration
Guide version 8.91.
• HTC 10M • LG G2
7
Nemo Outdoor Device Configuration Guide
Autodetection works with all Nemo Outdoor test terminals verified by Keysight. In some cases it
is possible that the terminal is not recognized and the autodetection does not work. If this
happens, manually select the correct trace and modem ports. Then select Automatic in the PS
data connection field and click Apply. If the automatic data connection detection does not
work, please see instructions below.
8
Nemo Outdoor Device Configuration Guide
2. Select the correct terminal from the list and click Next.
With Nokia terminals, select the item with the highest number, e.g., in this case #3.
3. In the Telephone Number field, enter *99# (#777 for CDMA terminals). In the
Connection name field type, for example, Nokia Dial-up connection. Select Allow
other people to use this connection. Click Connect.
9
Nemo Outdoor Device Configuration Guide
5. Click Close.
6. Go to Control Panel | Network and Internet | Network and Sharing Center, and select
Connect to a network. Right-click on the Terminal Dial-up Connection, and select
Properties.
10
Nemo Outdoor Device Configuration Guide
7. In the Networking tab, deselect the Internet Protocol Version 6 (TCP/IPv6) item and
select Internet Protocol Version 4 (TCP/IPv4). Click OK.
11
Nemo Outdoor Device Configuration Guide
9. Select the Advanced tab, and type in atz in the Extra initialization commands field,
and click on OK.
10. See the following chapters for terminal-specific instructions on adding terminals to
Nemo Outdoor.
When NATA is used, check that the mobile data setting is enabled from the device.
Pull down the menu from the top of the device screen and check that the mobile data
setting is activated.
1. Go to the developer options of the NATA device. Enable USB debugging and accept
ADB authorization popup (automatically done with the latest Nemo firmware).
12
Nemo Outdoor Device Configuration Guide
2. Start NATA. ADB forwarding is enabled by default if the device supports it. Also,
Outdoor USB mode is selected by default.
3. To see more USB mode options, go to Settings – General and enable the Show
advanced USB modes option.
13
Nemo Outdoor Device Configuration Guide
4. Follow the device-specific instructions in this document for installing the device drivers.
5. After the drivers have been installed, connect the device to the Nemo Outdoor laptop
and add the device in Nemo Outdoor.
6. In the Device Configuration dialog, select the correct ports for Trace port and Modem
port. See the device-specific instructions in this document for more detailed information.
7. Select Automatic in the ADB field.
8. Select ADB in the NATA field.
14
Nemo Outdoor Device Configuration Guide
When NATA is used, check that the mobile data setting is enabled from the device.
Pull down the menu from the top of the device screen and check that the mobile data
setting is activated.
1. First follow the device-specific instructions in this document for installing the device
drivers.
2. After the drivers have been installed, connect the device to the Nemo Outdoor laptop
and add the device in Nemo Outdoor.
3. In the Device Configuration dialog, select the correct ports for Trace port and Modem
port. See the device-specific instructions in this document for more detailed information.
15
Nemo Outdoor Device Configuration Guide
4. Select Automatic in the NATA and PS data connection fields. Click OK.
16
Nemo Outdoor Device Configuration Guide
5. If the NATA field is disabled, check that USB tethering has been activated. Go to
Windows Network and Sharing Center and click Change adapter settings.
6. In the Network Connections dialog, check that there is a Local Area Connection made
with the test device (e.g. Samsung) and that the connection is enabled. If the
connection is disabled, right-click on the connection and select Enable.
17
Nemo Outdoor Device Configuration Guide
7. If there is no local area connection for your test device, disconnect the USB cable,
reboot the test device, and then reconnect the device to the laptop. Also, try another
USB mode as the selection is device-specific.
8. To see more USB mode options, go to Settings – General and enable the Show
advanced USB modes option.
18
Nemo Outdoor Device Configuration Guide
Usually these devices can be added to Nemo Outdoor using autodetection (provided that the
diagnostics port is enabled) in which case Nemo Outdoor will automatically detect the correct
ports and data connections. If autodetection does not work for some reason, follow the
instructions below.
When NATA is used, check that the mobile data setting is enabled from the device.
Pull down the menu from the top of the device screen and check that the mobile data
setting is activated.
2. Ensure that USB debugging is enabled on the device and the ADB connection with the
controlling laptop is accepted. The steps to perform this are device specific.
3. Install the device drivers and connect the device to the Nemo Outdoor laptop.
4. In the Device Configuration dialog, select the correct ports for Trace port and Modem
port. See the device-specific instructions (if available) in this document for more detailed
information.
With some devices, the modem port setting should be set to Not Used to avoid
problems due to non-working AT command interpreter.
19
Nemo Outdoor Device Configuration Guide
20
Nemo Outdoor Device Configuration Guide
1.6 Using devices with Nemo Intelligent Device Interface and Nemo
Device Interface (NIDI/NDI)
When a Nemo Outdoor test device is used for the first time with Nemo Intelligent Device
Interface (NIDI) or Nemo Device Interface (NDI), you need to install the FTDI virtual COM port
driver. After installing the FTDI and device-specific drivers, devices can be added to Nemo
Outdoor using autodetection in which case Nemo Outdoor will automatically detect the correct
ports and data connections.
4. Select Browse my computer for driver software and go to the folder where you
downloaded the FTDI driver files (two .inf files). Click Next to start the installation.
5. After the installation is finished, return to the Device Manager. Under Universal Serial
BUS controllers, you should see a USB Serial Converter item. Right-click the item and
select Update Driver Software.
6. Select Browse my computer for driver software and go to the folder where you
downloaded the FTDI driver files (two .inf files). Click Next to start the installation.
21
Nemo Outdoor Device Configuration Guide
7. Return to the Device Manager. You should now see a USB Serial Port item under Ports
and the USB Serial Converter item under Universal Serial Bus controllers.
8. Next follow the device-specific instructions in this document for installing the device
drivers.
9. After the drivers have been installed, connect the devices to the Nemo Outdoor laptop
and add the devices with the autodetection tool.
22
Nemo Outdoor Device Configuration Guide
23
Nemo Outdoor Device Configuration Guide
Select Restart.
24
Nemo Outdoor Device Configuration Guide
When the computer starts up again, you will be given a list of startup settings that you can
change. Press the F7 key to select the Disable driver signature enforcement setting.
The computer will restart and you will now be able to install unsigned drivers.
25
Nemo Outdoor Device Configuration Guide
These instructions apply to the Apple iPhone carrier build phones provided by Apple.
1. Install iTunes.
2. Connect the iPhone to the control PC using the iPhone’s own cable.
3. Allow iPhone to connect to the control PC (iTunes will ask this, so if it is not started
automatically, you need to start it manually) and select Trust from the iPhone.
4. Check that there is an IP address in NATA.
5. If there is no IP address, switch on Personal Hotspot from the iPhone (switch off WiFi
before this). Select Bluetooth and USB Only.
26
Nemo Outdoor Device Configuration Guide
6. Go to Device Manager. Under Network Adapters you should see the Apple Mobile
Device Ethernet item.
7. Start Nemo Outdoor. Click the Autodetect button and start the device in Offline mode.
8. Go to the Nemo Outdoor Device Configuration dialog and select Automatic for the
NATA option.
When NATA is set to <Automatic>, Voice quality must be disabled because it is not
supported by NATA/iPhone.
27
Nemo Outdoor Device Configuration Guide
6. Click Install to start the installation and click Finish to finish the installation.
7. Close the BandLuxe software that appears, as it will not be required in the following
steps.
8. Go to Start | Control Panel | Hardware and Sound | Device Manager. Under Modems
you should be able to see the BandLuxe 3.5G Modem, under Network adapters you
28
Nemo Outdoor Device Configuration Guide
should see the BandLuxe 3.5G Ethernet Adapter, and under Ports the BandLuxe
Adapter Control Interface (COMxx) and BandLuxe AT CMD Interface (COMxx) items.
9. In Nemo Outdoor Device Configuration dialog, select the COM port number assigned
to the BandLuxe Adapter Control Interface item in the Trace Port field. Select the
COM port number assigned to the BandLuxe 3.5G Modem item (right-click the item
and select Properties) in the Modem Port field.
29
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo
Outdoor\Nemo Outdoor xx\Drivers\Bittium\Tough Mobile). Run the Qualcomm installer
QUD.WIN.1.1 Installer-10037.3.zip.
2. Select WWAN-DHCP as the Setup Type. Click Next.
30
Nemo Outdoor Device Configuration Guide
6. Go to Device Manager. Under Ports you should see the ToughMobile HS-USB
Diagnostics item. Under Modems you should see the ToughMobile HS-USB Android
Modem item.
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
8. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to ToughMobile HS-USB
Diagnostics.
• Modem port: Select the COM port number assigned to ToughMobile HS-USB Android
Modem.
• PS data connection: NDIS
9. Click Apply.
10. If the device connecting fails, check that you have selected the correct COM ports and
try again.
31
Nemo Outdoor Device Configuration Guide
Please note that currently the driver can be installed on 32-bit Windows only.
Install the device drivers. The file is located on the Nemo Outdoor USB flash drive.
Browse the file manually and double-click the 610_b038_multilanguage file. The
package will self-extract.
1. The Blackberry Desktop Software application is launched. Select the installation
language and click OK.
2. If the installer requests to install the Microsoft Visual C++ 2008 Redistributable file, click
Install.
3. Click Next to begin the Blackberry Desktop SW installation.
32
Nemo Outdoor Device Configuration Guide
9. Go to Device Manager. Under Modems you should see the Standard Modem item and
under Ports two RIM Virtual Serial Port v2 items.
10. Connect the device USB cable to the device and to the Nemo Outdoor laptop. Select
USB Drive from the device screen.
11. Start Nemo Outdoor. Autodetection does not work with the Blackberry device so add
the device manually (Add New Device | Phone | Qualcomm).
12. In the Device Configuration dialog, select the COM port with the bigger number
assigned to the RIM Virtual Serial Port v2 item in the Trace Port field. Select the COM
33
Nemo Outdoor Device Configuration Guide
port with the smaller number in the Modem Port field. Select Automatic in the PS data
connection field.
34
Nemo Outdoor Device Configuration Guide
6 Cellient R40
Please note that this driver is an unsigned driver. Driver signature verification on 64-
Bit Windows 8.1 or 10 needs to be disabled. Please follow the instructions in chapter
1.4.
1. Extract the Cellient R40 drivers.zip file and run the Setup.exe file.
2. When the installation is finished, connect the USB cable.
3. In Windows Device Manager, you will see several Cellient devices under Other
devices.
35
Nemo Outdoor Device Configuration Guide
6. Click Browse and browse to the Cellient R40 drivers\driver files folder. Click OK and
Next.
7. During the installation, a security message will appear. Select Install this driver
software anyway to continue the installation.
36
Nemo Outdoor Device Configuration Guide
9. Repeat steps 4-8 for all Cellient devices under Other devices. One of the devices may
not get drivers (“Windows was unable to install your Cellient”), but that does not affect
the device behavior with Nemo Outdoor.
10. After updating the driver software for all the Cellient devices, go to Device Manager.
You should see the following:
• Under Modems:
o Qualcomm HS-USB Android Modem 9025
• Under Network adapters:
o Qualcomm HS-USB WWAN Adapter 9025
• Under Ports:
o Qualcomm HS-USB Diagnostics 9025
o Qualcomm HS-USB NMEA 9025
37
Nemo Outdoor Device Configuration Guide
3. Click on the available connection and press Connect. If you are using Windows 8,
select the Connect Automatically option before pressing Connect. In Windows 7, you
will need to select the Connect automatically except when roaming or Always connect
automatically option after pressing Connect.
38
Nemo Outdoor Device Configuration Guide
1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse
the file manually and double-click the USB2VCOM_driver_x.xx.xx file (x is the latest
driver version).
2. Select Uninstall old version first if installed, and click Install in the Leadcore Technology
DTM8100 Series Driver Installer dialog.
3. In the VCOM Number field you need to select 3 ports for each test terminal. Since the
driver is installed only once, select the number of COM ports according to how many
Leadcore terminals you intend to use with Nemo Outdoor. Hence, if you want to
connect two Leadcore terminals with Nemo Outdoor, select at least 6 in the VCOM
Number field. Click Exit when the installation is done.
4. After the driver installation is finished, Windows may restart your computer but it is not
required.
5. After your computer has restarted, connect the connectivity cable to the mobile and the
other end to the computer’s USB port. Windows will detect the new hardware
automatically and start the installation. The step is repeated several times until all new
hardware is added.
6. In the Welcome page, select No, not this time and click Next.
7. Select Install the software automatically (Recommended) and click Next.
8. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware
Installation dialog if it appears. You may need to repeat steps 6, 7 and 8 several times
until the installation process is finished.
9. After installation, go to Device Manager. Select Start | Control Panel open the
Hardware and Sound tab and click the Device Manager button.
10. You should be able to see three Datang Mobile modems under Modems, and three
Datang Mobile items under Ports.
39
Nemo Outdoor Device Configuration Guide
11. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device
Manager you will find the COM port numbers needed in the next steps.
12. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the terminal. Click Next.
13. In the Device Manager click on Ports. Select the COM port number assigned to the
Leadcore Technology DTM8100 Modem #2 item In the Trace Port field in the Device
Configuration dialog. Select the COM port number assigned to the Leadcore
Technology DTM8100 Modem #3 item in the Modem Port field.
14. In the Device Configuration dialog, select <Automatic> as the PS data connection
(see page 8). Click Apply.
15. If the device connecting fails, check that you have selected the correct COM ports and
try again.
40
Nemo Outdoor Device Configuration Guide
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
6. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Qualcomm HS-USB MDM
Diagnostics 90B5.
• Modem port: Select the COM port number assigned to Qualcomm HS-USB Modem
90B5.
• PS data connection: NDIS
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
41
Nemo Outdoor Device Configuration Guide
9 Exelonix
Do not connect the device to your Nemo Outdoor laptop until the driver installation is
complete.
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder.
Install the Qualcomm USB Drivers for Windows 1.00.44. Double-click the Setup file to
run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Ports you should see the Qualcomm HS-USB MDM
Diagnostics 90B2 item. Under Modems you should see the Qualcomm HS-USB
Modem 90B2 item.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Qualcomm HS-USB MDM
Diagnostics 90B2
• Modem port: Select the COM port number assigned to the Qualcomm HS-USB
Modem 90B2 item.
6. In the Device Configuration dialog, select Automatic as the PS data connection (see
page 8). Click Apply.
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
42
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\). Double-click the
Google_Pixel_USB_Host_Driver_1.00.37 zip (Qualcomm driver for Pixel 3) file and
run the Setup.exe file to run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Ports you should see the Qualcomm HS-USB MDM
Diagnostics 90B5 item. Under Modems you should see the Qualcomm HS-USB
Modem 90B5 item.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Qualcomm HS-USB MDM
Diagnostics 90B5.
• Modem port: Select the COM port number assigned to the Qualcomm HS-USB Modem
90B5.
• For PS data connection select <Remote NDIS based Internet Sharing Device>. Click
Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
You can also try selecting Not used for the Modem port.
43
Nemo Outdoor Device Configuration Guide
11 HTC U11
Do not connect the USB connectivity cable to your PC until the driver installation is
complete.
Do not use autodetection with this device. The device needs to be added manually in
Nemo Outdoor.
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\HTC). Double-click the
HTCDriver_4.17.0.001 file to run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Ports you should see the HTC Diagnostics Interface
item.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the HTC item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to HTC Diagnostics Interface.
• For PS data connection select <Remote NDIS based Internet Sharing Device>. Click
Apply.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again. You can also try selecting Not used for the Modem port.
44
Nemo Outdoor Device Configuration Guide
12 HTC U12+
Do not connect the USB connectivity cable to your PC until the driver installation is
complete.
Do not use autodetection with this device. The device needs to be added manually in
Nemo Outdoor.
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\HTC). Install the Qualcomm USB Drivers
for Windows 1.00.44. Double-click the Setup file to run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Other devices right-click on one of SDM845-MTP
devices and select Properties.
4. Go to the Details page. In the Property field, select Hardware Ids. Check if the Value is
“_04”. If not, go back to step 3 and select another SDM845-MTP device and repeat step
4.
45
Nemo Outdoor Device Configuration Guide
5. When the device with the value _04 is found, return to the Device Manager, right-click
on the device and select Update driver.
6. Select Browse my computer for driver software - Let me pick from a list… - Show
all devices - Next - Have a disk. Browse to the Qualcomm driver installation folder
(e.g. C:\Program Files (x86)\QUALCOMM Incorporated\Qualcomm USB Drivers For
Windows\DriverPackage\Qualcomm\Fre\Windows7) and click Open - OK.
7. Select Qualcomm Incorporated - Qualcomm HS-USB Diagnostics 9080 - Next -
Yes – Close.
46
Nemo Outdoor Device Configuration Guide
8. Return to the Device Manager. Under Ports, you should now see the Qualcomm HS-
USB Diagnostics 9080 port installed. this is your trace port in Outdoor.
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the HTC item. Click Next.
8. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Qualcomm HS-USB Diagnostics
9080.
• For PS data connection select <Automatic>. Click Apply.
9. If the device connecting fails, check that you have selected the correct COM ports and
try again. You can also try selecting Not used for the Modem port.
47
Nemo Outdoor Device Configuration Guide
13 Huawei P9
1. In case there are previously installed Huawei drivers on the computer, first, uninstall any old
drivers.
2. Make sure that HUA (HiSilicon UE Agent) / Hisi agent is not switched on, so that it will not
occupy serial ports.
3. Go to Start | Network Connections. Right-click on Remote NDIS based Internet Sharing
Device (Ethernet) and Select Properties. Confirm selection by clicking Yes. Go to
Networking page and disable Ipv6 in the network adapter settings. Note that unless the
device’s USB port is changed, disabling Ipv6 only needs to be done once.
4. Connect the device to your computer’s USB port. Depending on the phone model NATA may
be available for the phone. If, however, NATA is not available, USB tethering must be
enabled manually by switching on USB tethering from the phone’s UI. The procedure for
getting USB tethering and trace port working together is as follows:
• Turn on USB tethering from the phone (trace and modem ports will disappear)
• Switch on trace ports by using the HiSilicon Android app. (background settings -> USB
port settings -> USB ports setting -> Balong debug mode. When device ask to reboot,
just cancel with back button.)
• Turn on USB tethering again (now USB tethering and ports are both enabled)
5. Use Autodetection to add device to Nemo Outdoor. Steps 6 and 7 only need to be followed
if autodetection is not used.
6. In Nemo Outdoor, go to Add phone | HiSilicon Kirin. In Device Configuration dialog select
the port assigned to HUAWEI Mobile Connect – GPS Interface in the Trace Port field. In the
Modem port field select the port assigned to Huawei Mobile Connect - Modem. You can find
the right port and modem in Device Manager:
7. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click Apply.
8. If the device connecting fails, check that you have selected the correct COM ports and try
again.
48
Nemo Outdoor Device Configuration Guide
14 Huawei E398
Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager
starts up every time the device is plugged in and it must be closed in order to be able
to use the device with Nemo Outdoor. As a workaround, the Connection Manager
.exe file can be renamed. A reinstall warning will be displayed when device is
plugged in but this can be ignored.
1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and start the installation. Click Run AutoRun.exe and follow the
instructions on the screen.
2. The Telenor Mobile Partner software starts up. Close the program.
3. After installation, go to Device Manager. Select Start | Control Panel, open the
Hardware tab and click the Device Manager button.
4. You should see the Huawei Mobile Connect – Modem item under Modems and the
Huawei Mobile Connect – Application Interface and Huawei Mobile Connect – PC UI
Interface items under Ports.
5. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device
Manager you will find the COM port numbers needed in the next steps.
6. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the Qualcomm item. Click Next.
7. In the Device Manager click on Ports. Select the COM port number assigned to the
Huawei Mobile Connect – PC UI Interface item in the Trace Port field in the Device
Configuration dialog. Select the COM port number assigned to the Huawei Mobile
Connect - Modem item in the Modem Port field.
8. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click
Apply.
9. If the device connecting fails, check that you have selected the correct COM ports and
try again.
Windows 7:
1. Plug in the Huawei device.
2. Go to Start | Control Panel | Network and Internet | Network and Sharing Center.
3. Click on Change adapter settings.
49
Nemo Outdoor Device Configuration Guide
5. In the Mobile Broadband Connection Properties dialog, select Internet Protocol Version
4 (TCP/IPv4) and click on Properties.
50
Nemo Outdoor Device Configuration Guide
15 Huawei Mate 20X, Mate 30 5G, Mate 30 Pro, Mate 30 Pro 5G, P40,
P40 Pro
To keep the diagnostic interface open for the HiSilicon Balong 5000 based devices,
you need to have the diagnostic interface SW activated on your PC. When the
HiSilicon handler SW is started in Nemo Outdoor, the status of the diagnostic
interface SW is automatically checked. The computer in which the Nemo Outdoor
SW is running, needs to be periodically (about once a week) connected to the
internet. If the diagnostic interface SW is not activated, the message below will be
shown. After the connection has been successfully established, the diagnostic
interface SW will be re-activated and the diagnostic interface will be enabled again.
1. Plug in the device in one of your PC’s USB ports. The drivers are automatically
installed, and Windows automatically detects the device.
51
Nemo Outdoor Device Configuration Guide
2. Select View | Windows Device Manager. In the Device Manager, you should see the
following items and their COM port numbers under Ports.
3. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the HiSilicon item. Click Next.
4. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the HUAWEI Mobile Connect -
GPS Interface item.
• Modem port: Select the COM port number assigned to the Android Adapter PCUI
item.
• For PS data connection select <Automatic>. Click Apply.
5. If the device connecting fails, check that you have selected the correct COM ports and
try again.
52
Nemo Outdoor Device Configuration Guide
53
Nemo Outdoor Device Configuration Guide
16 Kodiak PTT
54
Nemo Outdoor Device Configuration Guide
9. Select the Show the Bluetooth icon in the notification area option.
55
Nemo Outdoor Device Configuration Guide
4. Select Add a Device from the Bluetooth menu on your laptop and follow the wizard to
add the phone.
56
Nemo Outdoor Device Configuration Guide
6. You should now see your phone as a device in the Devices and Printers view.
57
Nemo Outdoor Device Configuration Guide
3. On the Services page, select the Serial port (SPP) ‘KodiakPoCApplication’ option.
58
Nemo Outdoor Device Configuration Guide
5. Go back to the PTT1 Properties, Services page. You should now see a COM port
assigned for the Serial port.
6. You should also see a COM port under Ports in Device Manager.
59
Nemo Outdoor Device Configuration Guide
4. In the Kodiak PTT port field, select the COM port that was assigned for the Standard
Serial over Bluetooth link item (check from Device Manager, Ports).
60
Nemo Outdoor Device Configuration Guide
5. When using the Application Tester handler, there is no need to configure the Trace or
Modem ports. Also data connections can be “Not Used” if only Kodiak testing will be
performed.
6. Press OK to add the device. You are now ready to start the measurements.
61
Nemo Outdoor Device Configuration Guide
17 LG G4, G6
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
6. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Qualcomm HS-USB
Diagnostics.
• Modem port: Select the COM port number assigned to Qualcomm HS-USB Android
Modem.
• PS data connection: NDIS
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
62
Nemo Outdoor Device Configuration Guide
1. To install the drivers, run the CDM21216 Setup item available in the Nemo Outdoor
product package and click Extract.
2. Follow the instructions in the Installation Wizard to finish the setup.
3. Connect the device to your computer’s USB port.
4. Go to the Device Manager. Two USB Serial Port items should appear under Ports.
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Neul item. Click Next.
6. For Trace Port and Modem Port fields in the Device Configuration dialog, select the
ports assigned to the two USB Serial Port items in Device Manager (in the example
above COM 4 and COM 5). There is no way of knowing which port is which so if the
device connecting fails, try selecting the ports again. Click Apply.
63
Nemo Outdoor Device Configuration Guide
1. Browse to the Drivers folder on the Nemo Outdoor USB flash drive.
2. Run the QualcommUSBDriver.WIN.1.1_Installer-10037.3 file to start the installation
wizard. If the Windows Security dialog appears, click Run.
3. After the device driver installation is finished, connect the device to the computer.
Windows will automatically detect the new hardware and install drivers. Wait until the
installation process is finished.
4. Start Nemo Outdoor and connect the device using Autodetection.
5. In the User Interface Properties – Measurement dialog, select option Disable default
gateway for the Routing table modifications for devices setting.
64
Nemo Outdoor Device Configuration Guide
1. Browse to the Drivers folder on the Nemo Outdoor USB flash drive.
2. Run the SIM7070_SIM7080_SIM7090_Windows_Driver_Installer_V1.00 file to start
the installation wizard. If the Windows Security dialog appears, click Run.
3. After the device driver installation is finished, connect the device to the computer.
Windows will automatically detect the new hardware and install drivers. Wait until the
installation process is finished.
4. Start Nemo Outdoor and connect the device using Autodetection.
5. In the User Interface Properties – Measurement dialog, select option Disable default
gateway for the Routing table modifications for devices setting.
65
Nemo Outdoor Device Configuration Guide
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
6. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Qualcomm HS-USB MDM
Diagnostics 90E7.
• Modem port: Select the COM port number assigned to Qualcomm HS-USB Modem
90E7.
• PS data connection: NDIS
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
66
Nemo Outdoor Device Configuration Guide
1. Extract the “Moto XT1575 drivers.zip” file on the desktop or other easy-to-remember
location.
2. Run Setup.exe and follow instructions on the screen to finish the installation.
3. Connect the USB cable from the device to your computer.
4. In Windows Device Manager, you should see several devices under “Other devices”.
67
Nemo Outdoor Device Configuration Guide
7. Click Browse, go to the Moto XT1575 drivers\driver files folder and click OK and Next.
8. A security pop-up will appear. Select Install this driver software anyway to continue
the installation.
68
Nemo Outdoor Device Configuration Guide
10. Repeat steps 5-9 for all of the devices under “Other devices” (at the beginning there
should be “diag”, “modem” and “nmea”). After installation, go to Device Manager. You
should see the following items:
Under Modems:
• Qualcomm HS-USB Android Modem 9026
Under Network adapters:
• Remote NDIS based Internet Sharing Device
Under Ports:
• Qualcomm HS-USB Diagnostics 9026 (COMxx)
• Qualcomm HS-USB NMEA 9026 (COMxx)
69
Nemo Outdoor Device Configuration Guide
3. After installation, go to Device Manager. You should see the following items:
Modems: Sierra Wireless WWAN Modem
Ports: Sierra Wireless DM Port
70
Nemo Outdoor Device Configuration Guide
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Sierra Wireless DM Port
• Modem port: Select the COM port number assigned to Sierra Wireless WWAN
Modem
6. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click
Apply.
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
71
Nemo Outdoor Device Configuration Guide
1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse
to folder Nemo Outdoor 7.7.1.14\Drivers\Qualcomm\Netgear\[your device model] and
run the .exe file.
2. Follow the instructions in the installation wizard to finish the driver installation.
3. Connect the connectivity cable to the mobile and the other end to the computer’s USB
port. Windows will detect the new hardware automatically and install the necessary
drivers.
4. After installation, go to Device Manager. You should see the following items:
Modems: Netgear WWAN Modem
Ports: Netgear DM Port
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
6. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Netgear DM Port
• Modem port: Select the COM port number assigned to Netgear WWAN Modem
7. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click
Apply.
8. If the device connecting fails, check that you have selected the correct COM ports and
try again.
72
Nemo Outdoor Device Configuration Guide
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
6. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Quectel USB DM Port
• Modem port: Select the COM port number assigned to Quectel USB Modem
• In the Device Configuration dialog, select <NDIS> as the PS data connection.
7. Click Apply. If the device connecting fails, check that you have selected the correct
COM ports and try again.
73
Nemo Outdoor Device Configuration Guide
26 Nokia 500
Do not connect the USB connectivity cable to your PC until the driver installation is
complete.
1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse
to folder Nemo Outdoor x.xx\Drivers\Nokia drivers\Nokia 500 and run the
Nokia_Suite_webinstaller_All file.
2. When the installation starts, choose your language and click Install.
3. Click I accept.
4. After the Nokia Suite installation is finished, close the installation dialog and connect the
connectivity cable to the mobile and the other end to the computer’s USB port. Windows
will detect the new hardware automatically and install the drivers.
5. After installation, go to Device Manager. Under Wireless Communication Devices you
should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see
three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there
the COM port numbers needed in the next steps.
6. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the terminal. Click Next.
7. In the Device Manager click on Modems. Select the COM port number assigned to the
first/unnumbered Nokia xxx USB item In the Trace Port field in the Device
Configuration dialog. Select the COM port number assigned to the second highest
Nokia xxx USB item in the Modem Port field.
74
Nemo Outdoor Device Configuration Guide
75
Nemo Outdoor Device Configuration Guide
1. Insert the (U)SIM card supplied by your service provider in the terminal. Please refer to
the quick start guide for more detailed instructions as to how to do this.
2. Insert the Novatel Ovation USB modem into your PC USB port.
3. Windows will automatically install the device driver and detect the new device. In
addition, it automatically installs MobiLink Lite which is the device software. Ignore this
software, and close it. It should not be on when adding the device to Nemo Outdoor.
4. Next, go to Start | Control Panel | Phone and Modem Options | Modems on your
PC. The list should display Novatel Wireless Modem item and the associated COM
port number, in this case COM26.
76
Nemo Outdoor Device Configuration Guide
5. When the installation is complete, check from the Device Manager that the installation
was successful. Under Modems you should see the Novatel Wireless Modem item and
under Ports you should see the Novatel Wireless Application Port, Novatel Wireless
EAP-SIM Port and Novatel Wireless Status Port items. Under Network adapters you
should see the Novatel Wireless Network Adapter item. Leave the Device Manager
open as you will find there the COM port numbers needed in the next steps.
77
Nemo Outdoor Device Configuration Guide
4. Select Include this location in the search and browse to folder D:\Nemo
Drivers\Novatel MC727 usb drivers on the Nemo Outdoor USB flash drive. Click Next.
5. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new
hardware is ready to be used.
6. When the installation is complete, check from the Device Manager that the installation
was successful. Under Ports you should see the Novatel Wireless Ovation EV-DO
Diagnostic Port (COMxx), Novatel Wireless Ovation EV-DO GPS Port (COMxx) and
78
Nemo Outdoor Device Configuration Guide
Novatel Wireless Ovation EV-DO Status Port (COMxx )items. Leave the Device
Manager open as you will find there the COM port numbers needed in the next steps.
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
8. In the Device Manager click on Ports. Select the COM port number assigned to the
Novatel Wireless Status Port item in the Trace Port field in the Device Configuration
dialog. Leave the Modem Port field empty.
9. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
10. If the device connecting fails, check that you have selected the correct COM ports and
try again.
79
Nemo Outdoor Device Configuration Guide
1. First the Connection Manager is installed. The installation file is located on the Nemo
Outdoor USB flash drive. Browse the file and double-click the
LTE7210_xxxx_EngineeringRelease.exe file (xxxx refers to the version number).
2. First select the Installer language and click OK.
3. Click Next in the Welcome dialog. Click I Agree in the License Agreement dialog.
4. Choose the destination folder and click Next.
5. If at some point you see the Select Components dialog, select Full Installation and
click Next.
80
Nemo Outdoor Device Configuration Guide
7. At some point during the Connection Manager installation, the Device Driver Installation
Wizard starts up automatically. Click Next in the Welcome dialog.
8. The device driver installation is completed and you can now connect the device to your
computer. Click Finish.
81
Nemo Outdoor Device Configuration Guide
9. Windows will automatically detect the new hardware and install the required drivers.
10. Return to the Connection Manager installation. When the installation is complete, click
Finish.
11. The Connection Manager will launch automatically but it is important that it is closed
before adding the device to Nemo Outdoor. It is recommended that you rename the
.exe file that launches the Connection Manager to prevent the CM from starting. Browse
to C:\Program Files \NSN LTE Connection Manager (or for 64-bit Windows C:\Program
Files (x86)\NSN LTE Connection Manager) and rename the nsnltecm.exe to
nsnltecm.exe_.
12. To avoid performance issues with the modem, the Altair LogCreator standalone
functionality needs to be disabled. Browse to folder C:\Program Files\NSN LTE
Connection Manager\Tools\ Internals\LogCreator and open file RunLogCreator.bat
with Notepad. Modify the following string:
• Original: LogCreator.exe -SA -FN:"50" -E -Y4:"LOG_SOCK_IF" -
D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"
• Modified: LogCreator.exe -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -
D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"
82
Nemo Outdoor Device Configuration Guide
13. Go to Device Manager. Under Ports you should see Nokia Siemens Networks LTE
Application Interface item.
14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select Altair. Click Next.
15. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select Altair USB
• Modem port: Select the COM port number assigned to the Nokia Siemens Networks
LTE Application Interface
16. In the Device Configuration dialog, select <NDIS> and click Apply.
17. If the device connecting fails, check that you have selected the correct COM ports and
try again. Also check that the NSN Connection Manager is not running.
83
Nemo Outdoor Device Configuration Guide
30 Onda MT689DC
1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and start the installation. Click Run AutoRun.exe and follow the
instructions on the screen.
2. Select your language and destination folder. By clicking Next, you also accept the
license agreement.
3. When the installation is finished, unplug the device from the USB port and restart the
computer.
4. Plug the device back to the USB port. Close the AutoPay dialog.
5. If the Chiavetta Internet MT689DC software starts up, close the program.
6. After installation, go to Device Manager. Select Start | Control Panel, open the
Hardware and sound tab and click the Device Manager button.
7. You should see the ONDA Proprietary HS-USB Modem item under Modems and the
ONDA HS-USB Diagnostics Interface item under Ports.
84
Nemo Outdoor Device Configuration Guide
8. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
9. In the Device Configuration dialog, select the COM port number assigned to ONDA
HS-USB Diagnostics Interface item in the Trace Port field. Select the COM port
number assigned to the ONDA Proprietary HS-USB Modem item in the Modem Port
field.
10. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
11. If the device connecting fails, check that you have selected the correct COM ports and
try again.
85
Nemo Outdoor Device Configuration Guide
31 OnePlus
1. Browse to folder Drivers\Qualcomm based devices\OnePlus on the Nemo Outdoor USB
flash drive.
2. Run the Qualcomm USB Host Driver, Setup.exe file to start the installation wizard. If
the Windows Security dialog appears, click Run.
3. After the device driver installation is finished, connect the terminal to the computer with
a USB cable. Windows will automatically detect the new hardware and install drivers.
Wait until the installation process is finished.
4. After installation, go to Device Manager. You should see the Qualcomm HS-USB
Modem 90B5 item under Modems and Qualcomm HS-USB MDM Diagnostics 90B5
item under Ports.
5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
6. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to Qualcomm HS-USB MDM
Diagnostics 90B5.
• Modem port: Select the COM port number assigned to Qualcomm HS-USB Modem
90B5.
• PS data connection: NDIS
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
86
Nemo Outdoor Device Configuration Guide
87
Nemo Outdoor Device Configuration Guide
32 Pantech UM175
1. Unzip the driver files (PANTECH UM175 USB drivers.zip) on your computer.
2. Plug in the data card.
3. Windows will automatically detect the new hardware.
4. Select Install the software automatically (Recommended), and click Next.
5. Select Include this location in the search and browse for the folder where the driver
files are located (e.g., C:\Pantech UM175). Click Next.
88
Nemo Outdoor Device Configuration Guide
7. Next go to Device Manager. Under Modems you should see the PANTECH UM175
item, and under Ports the PANTECH UM175 Diagnostic Port item.
If you do not see the items mentioned above and instead there are three unknown
devices under Others, the driver installation has failed. Right-click each unknown
item, select Update Driver Software, and browse to the folder where you unzipped
the driver files. After the update, the Pantech items should appear in the Device
Manager.
8. Next, set up the data connection manually. Follow instructions on page 8 (for Win 7)
then continue from step 9.
89
Nemo Outdoor Device Configuration Guide
9. In the Pantech UM175 Modem Properties dialog, Security page, select No encryption
allowed in the Data encryption field. Click OK to close the dialog.
10. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
11. In the Nemo Outdoor Device Configuration dialog, define the following settings (check
the port numbers from the Device Manager) and click Apply:
• Trace port: Select the COM port number assigned to PANTECH UM175 Diagnostic
Port
• Modem port: Select the COM port number assigned to PANTECH UM175
• PS data connection: Select the data connection that you configured manually, for
example, Pantech UM175.
12. If the device connecting fails, check that you have selected the correct COM ports and
try again.
90
Nemo Outdoor Device Configuration Guide
33 Pantech UML290
1. Browse to folder D:\Drivers\Qualcomm LTE USB Modem on the Nemo Outdoor USB
flash drive.
2. Run the VZAM_7.6.3.4_2642j_PantechLTE.exe file to start the installation wizard. If the
Windows Security dialog appears, click Run.
3. The device drivers are installed first. After the device drivers are installed, the
VZAccess Manager installation is started.
4. Click Next in the Welcome window that appears.
5. Select I accept the terms in the license agreement and click Next.
91
Nemo Outdoor Device Configuration Guide
6. Click Next and Next. Select Typical in the Setup Type dialog and click Next and
Install. Wait until the installation is ready and click Finish.
7. Plug in the USB modem. Windows will automatically detect the new hardware and
install drivers. Wait until the installation process is finished.
8. After installation, go to Device Manager. Select Start | Control Panel | System, open
the Hardware tab and click the Device Manager button. You should see the Pantech
UML290 item under Modems and the Pantech UML290 Diagnostic Port item under
Ports.
92
Nemo Outdoor Device Configuration Guide
9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
10. In the Device Manager click on Modems. Select the port assigned to Pantech UML290
Diagnostic Port in the Trace Port field in the Device Configuration dialog. Select the
port assigned to Pantech UML290 in the Modem Port field.
11. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
12. If the device connecting fails, check that you have selected the correct COM ports and
try again.
93
Nemo Outdoor Device Configuration Guide
94
Nemo Outdoor Device Configuration Guide
5. Start Nemo Outdoor and use the Autodetect tool to connect the device. Select the
second Qualcomm port available in the dropdown menu.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
95
Nemo Outdoor Device Configuration Guide
1. To install the drivers, run the CDM21216 Setup item available in the Nemo Outdoor
product package and click Extract.
2. Follow the instructions in the Installation Wizard to finish the setup.
3. Connect the USB data cable to the USB port on the Quectel device and a power cable
from the device to a power source.
4. Connect the device to your computer’s USB port.
5. Switch power on from the Quectel device. When you are starting the device for the first
time, it may take some time before the device finds a network connection.
6. Go to the Device Manager. You should see the Quectel USB AT Port, Quectel USB
DM Port, and Quectel USB NMEA Port items under Ports and the Quectel USB
Modem item under Modems.
96
Nemo Outdoor Device Configuration Guide
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
8. In the Device Configuration dialog, select the port assigned to Quectel USB DM Port in
the Trace Port field and select the port assigned to Quectel USB AT Port in the Modem
Port field.
9. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
97
Nemo Outdoor Device Configuration Guide
1. To install the drivers, run the CDM21216 Setup item available in the Nemo Outdoor
product package and click Extract.
2. Follow the instructions in the Installation Wizard to finish the setup.
3. Connect a USB data cable (FTDI cable recommended) to the USB port marked MAIN
on the Quectel device (number 1 in the picture above). Windows will detect the
hardware.
4. Go to the Device Manager. A USB Serial Port item should appear under Ports. Select
this port as the Modem port in Nemo Outdoor Device Configuration dialog.
5. Connect the second USB data cable (FTDI cable recommended) to the USB port
marked DEBUG on the Quectel device (number 2 in the picture above). Windows will
detect the hardware.
98
Nemo Outdoor Device Configuration Guide
6. Go to the Device Manager. A second USB Serial Port item should appear under Ports.
Select this port as the Trace port in Nemo Outdoor Device Configuration dialog.
7. Connect a power cable from the device to a power source and switch on the device.
8. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Neul item. Click Next.
9. In the Device Configuration dialog, select the trace port and modem port as explained in
steps 4 and 6. Click Apply.
99
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click
the SIM7100_SIM7500 Series Windows USB driver_V1.00 file to run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Ports you should see the SimTech HS-USB MDM
Diagnostics 908B item. Under Modems you should see SimTech HS-USB Modem
908B items.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the SimTech HS-USB MDM
Diagnostics 908B
• Modem port: Select the COM port number assigned to the SimTech HS-USB Modem
908B.
6. In the Device Configuration dialog, select Automatic as the PS data connection (see
page 8). Click Apply.
7. If the device connecting fails, check that you have selected the correct COM ports and
try again.
100
Nemo Outdoor Device Configuration Guide
38 Samsung Devices
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, you must manually install the original Samsung CDC Composite Device
driver when connecting the device with Nemo Outdoor for the first time after the
update. This needs to be done for each USB port to which a Samsung device is
connected.
1. Connect the USB data cable from the device to your laptop.
2. Go to Device Manager.
3. Right-click on libusb-win32 devices and select Update Driver.
4. Select Browse My Computer for driver software.
5. Select Let me pick from list of available drivers on computer.
6. Select Samsung Mobile USB CDC Composite Device and click Next.
7. Disconnect and reconnect the USB cable to the device.
101
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets or
Nemo Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy
Handsets). Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run
the installation.
2. When the installation is complete, connect the device to the PC.
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, please follow the steps on page 101 to reinstall the original Samsung CDC
Composite Device driver. This needs to be done for each USB port to which a
Samsung device is connected.
3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial
Port item. Under Modems you should see the Samsung Mobile USB Modem item.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Samsung or Qualcomm item, depending on the
chipset of your device. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM29)
• Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.
102
Nemo Outdoor Device Configuration Guide
• For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again. You can also try selecting Not used for the Modem port.
103
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets or
Nemo Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy
Handsets). Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run
the installation.
2. When the installation is complete, connect the device to the PC.
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, please follow the steps on page 101 to reinstall the original Samsung CDC
Composite Device driver. This needs to be done for each USB port to which a
Samsung device is connected.
3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial
Port item. Under Modems you should see the Samsung Mobile USB Modem item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Samsung or Qualcomm item, depending on the chipset of your device.
Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM29).
• Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.
• For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.
104
Nemo Outdoor Device Configuration Guide
6. If the device connecting fails, check that you have selected the correct COM ports and
try again. You can also try selecting Not used for the Modem port.
105
Nemo Outdoor Device Configuration Guide
38.3 Samsung Galaxy S8, Note 8, S9, S9+, S10, S10 5G, Note 10+
5G
Auto detection should not be used to add the device. Add the device manually.
Go to the device AutoTether Settings and check that Enable USB auto tethering
option is selected. Under Developer options check that USB mode is set to RNDIS.
Do not connect the USB connectivity cable to your PC until the driver installation is
complete.
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the
installation.
2. When the installation is complete, connect the device to the PC.
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, please follow the steps on page 101 to reinstall the original Samsung CDC
Composite Device driver. This needs to be done for each USB port to which a
Samsung device is connected.
3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial
Port item. Under Modems you should see the Samsung Mobile USB Modem item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Samsung or Qualcomm item, depending on the chipset of your device.
Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port.
• Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.
• For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
You can also try selecting Not used for the Modem port.
106
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the
installation.
2. When the installation is complete, connect the device to the PC.
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, please follow the steps on page 101 to reinstall the original Samsung CDC
Composite Device driver. This needs to be done for each USB port to which a
Samsung device is connected.
3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial
Port item. Under Modems you should see the Samsung Mobile USB Modem item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Samsung or Qualcomm item, depending on the chipset of your device.
Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port.
• Modem port: Select <Not used>
• For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
You can also try selecting Not used for the Modem port.
107
Nemo Outdoor Device Configuration Guide
38.5 Samsung Galaxy S21, S21+, S21 Ultra, S21 FE, Z Flip 3, Z
Fold 3, S22, S22+, S22 Ultra
Do not connect the USB connectivity cable to your PC until the driver installation is
complete.
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the
installation.
2. When the installation is complete, connect the device to the PC.
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, please follow the steps on page 101 to reinstall the original Samsung CDC
Composite Device driver. This needs to be done for each USB port to which a
Samsung device is connected.
3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial
Port item. Under Modems you should see the Samsung Mobile USB Modem item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Samsung or Qualcomm item, depending on the chipset of your device.
Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port.
• Modem port: Select <Not used>.
• For PS data connection select <Not used>. Click Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
108
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the
installation.
2. When the installation is complete, connect the device to the PC.
If you have updated the firmware of your Samsung test device with Nemo Firmware
Manager, please follow the steps on page 101 to reinstall the original Samsung CDC
Composite Device driver. This needs to be done for each USB port to which a
Samsung device is connected.
3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial
Port item. Under Modems you should see the Samsung Mobile USB Modem item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port.
• Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.
• For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
You can also try selecting Not used for the Modem port.
109
Nemo Outdoor Device Configuration Guide
5. When these options are selected, you can close the Telstra Turbo Connection
Manager/Watcher application, and the device will work in Nemo Outdoor. However, if
these options are not selected, the Telstra Turbo Connection Manager/Watcher
application needs to run in the background while conducting measurements with the
Sierra device in Nemo Outdoor.
Note that the options may vary depending on the device. For example, with Sierra
306, the Tools button is a spanner icon, and instead of On exit field there is Enable
airplane mode on exit which needs to be set to No. In addition, the modem name
may change depending on the device, for example, to Sierra Wireless HSPA
modem.
6. When the installation is complete, check from the Device Manager that the installation
was successful. Go to Start | Control Panel | System and Security | System | Device
Manager. Under Modems you should see a Sierra Wireless AirCard HSDPA Modem
item and under Ports pay attention to the Sierra Wireless AT Command Port (UMTS)
(COMxx) and Sierra Wireless DM Port (UMTS) (COMxx) items. Under Network
Adapters you should see the Sierra Wireless HSPA Network Adapter item. Leave the
110
Nemo Outdoor Device Configuration Guide
Device Manager open as you will find there the COM port numbers needed in the next
steps.
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
8. In the Device Manager click on Ports. Select the COM port number assigned to the
Sierra Wireless DM Port item in the Trace Port field in the Device Configuration
dialog. Click on Modems. Select the COM port number assigned to the Sierra
Wireless AT Command Port item in the Modem Port field.
9. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
10. If the device connecting fails, check that you have selected the correct COM ports and
try again.
111
Nemo Outdoor Device Configuration Guide
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
8. In the Device Manager click on Ports. Select the COM port number assigned to the
Sierra Wireless Compass 597 DM Port item in the Trace Port field in the Device
Configuration dialog. Leave the Modem Port field empty.
9. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
10. If the device connecting fails, check that you have selected the correct COM ports and
try again.
112
Nemo Outdoor Device Configuration Guide
41 Sonim XP7700
1. Run the install.bat file from folder Drivers\Qualcomm\Sonim\Sonim XP7700 found on
the Nemo Outdoor USB flash drive to start the installation wizard and wait for the
installation to finish.
2. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.
3. Go to Device Manager. You should see the following items:
• Modems: Sonim XP7700 HS-USB Android Modem
• Ports: Sonim XP7700 HS-USB Diagnostics
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Device Configuration dialog, make the following settings and click Apply:
• Trace Port: Select the port assigned to Sonim XP7700 HS-USB Diagnostics
• Modem Port: Select the port assigned to Sonim XP7700 HS-USB Android Modem
• PS data connection: Select Qualcomm HS-USB Modem
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
113
Nemo Outdoor Device Configuration Guide
42 Sonim XP8800
1. Run the Sonim USB driver found on the Nemo Outdoor USB flash drive to start the
installation wizard and wait for the installation to finish.
2. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.
3. Go to Device Manager. You should see the following items:
• Modems: Qualcomm HS-USB Modem 90B5
• Ports: Qualcomm HS-USB Diagnostics
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Device Configuration dialog, make the following settings and click Apply:
• Trace Port: Select the port assigned to Qualcomm HS-USB Diagnostics
• Modem Port: Select the port assigned to Qualcomm HS-USB Modem 90B5
• PS data connection: Select Qualcomm HS-USB Modem
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
114
Nemo Outdoor Device Configuration Guide
10. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
11. Select the port assigned to Sony HS-USB Android Diag in the Trace Port field in the
Device Configuration dialog. Select the port assigned to Sony HS-USB Android Modem
in the Modem Port field.
12. In the Device Configuration dialog, select <Remote NDIS Compatible Device> as the
PS data connection. Click Apply.
115
Nemo Outdoor Device Configuration Guide
13. If the device connecting fails, check that you have selected the correct COM ports and
try again.
116
Nemo Outdoor Device Configuration Guide
1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically.
2. To install a driver, select the Sony_Eng_Drivers item and click Next.
3. Click Yes in the Update Driver Warning message.
4. Click Close when the installation is finished.
5. Return to the Device Manager. The Sony HS-USB Android Modem item should
appear under Modems.
6. Again, right-click on the Sony HS-USB Android Modem and select Update Driver
Software.
7. Select the Sony_Eng_Drivers item and click Next.
8. Click Yes in the Update Driver Warning message and click Close when the installation
is finished.
9. Return to the Device Manager. The Sony HS-USB Android Diag item should appear
under Ports.
10. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
117
Nemo Outdoor Device Configuration Guide
11. Select the port assigned to Sony HS-USB Android Diag in the Trace Port field in the
Device Configuration dialog. Select the port assigned to Sony HS-USB Android Modem
in the Modem Port field.
12. In the Device Configuration dialog, select <Remote NDIS Compatible Device> as the
PS data connection. Click Apply.
13. If the device connecting fails, check that you have selected the correct COM ports and
try again.
118
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Sony). Double-click the Qualcomm USB
Drivers for Windows xxx.exe to run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Ports you should see the Qualcomm HS-USB MSM
Diagnostics 90F9 item. Under Modems you should see the Qualcomm HS-USB
Modem 90F9 item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Qualcomm HS-USB MSM
Diagnostics 90F9.
• Modem port: Select the COM port number assigned to the Qualcomm HS-USB
Modem 90F9.
• For PS data connection select <Remote NDIS Compatible Device>. Click Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
You can also try selecting Not used for the Modem port.
119
Nemo Outdoor Device Configuration Guide
120
Nemo Outdoor Device Configuration Guide
1. To install the drivers, run the CDM21216 Setup item available in the Nemo Outdoor
product package and click Extract.
2. Follow the instructions in the Installation Wizard to finish the setup.
3. Connect a USB data cable to the USB port (port number 1 in the picture above) and a
power cable (port number 2 in the picture above) from the device to a power source.
4. Connect the device to your computer’s USB port.
5. Switch power on from the U-Blox device (see item number 3 in the picture above).
6. Go to the Device Manager. Two USB Serial Port items should appear under Ports.
7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Neul item. Click Next.
121
Nemo Outdoor Device Configuration Guide
8. For Trace Port and Modem Port fields in the Device Configuration dialog, select the
ports assigned to the two USB Serial Port items in Device Manager (in the example
above COM 4 and COM 5). There is no way of knowing which port is which so if the
device connecting fails, try selecting the ports again. Click Apply.
122
Nemo Outdoor Device Configuration Guide
1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder
(e.g. Nemo Outdoor\Nemo Outdoor xx\Drivers\Xiaomi). Double-click the Qualcomm
USB Drivers for Windows xxx.exe to run the installation.
2. When the installation is complete, connect the device to the PC.
3. Go to Device Manager. Under Ports you should see the Qualcomm HS-USB MSM
Diagnostics 90E7 item. Under Modems you should see the Qualcomm HS-USB
Modem 90E7 item.
4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone
and select the Qualcomm item. Click Next.
5. In the Nemo Outdoor Device Configuration dialog, define the following settings:
• Trace port: Select the COM port number assigned to the Qualcomm HS-USB MSM
Diagnostics 90E7.
• Modem port: Select the COM port number assigned to the Qualcomm HS-USB
Modem 90E7.
• For PS data connection select <Remote NDIS Compatible Device>. Click Apply.
If the device connecting fails, check that you have selected the correct COM ports and try again.
You can also try selecting Not used for the Modem port.
123
Nemo Outdoor Device Configuration Guide
48 ZTE MF820T/MF820D
1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.
2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow
the instructions on the screen. Select Yes in the User Account Control dialog if it
appears.
When the installation is finished, it is important to close the Mobile Broadband
application.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Device Configuration dialog, make the following settings and click Apply:
• Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port
• Modem Port: Select the port assigned to ZTE Mobile Broadband AT Port
• PS data connection: Select <NDIS>.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
124
Nemo Outdoor Device Configuration Guide
49 ZTE MF668A
1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.
2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow
the instructions on the screen. Select Yes in the User Account Control dialog if it
appears.
When the installation is finished, it is important to close the Mobile Broadband
application.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Device Configuration dialog, make the following settings and click Apply:
• Trace Port: Select the port assigned to ZTE Diagnostics Interface
• Modem Port: Select the port assigned to ZTE Proprietary USB Modem
• PS data connection: Select <NDIS>.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
125
Nemo Outdoor Device Configuration Guide
50 ZTE MF683
1. Start the driver installation by selecting the correct installation file based on your
operating system (..\Drivers\Qualcomm\ZTE\ZTE MF683\USBDriverInstaller_x64.exe
or USBDriverInstaller_x86.exe). The installation will run on the background.
2. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.
3. Go to Device Manager. You should see the following items:
• Modems: T-Mobile HSPA+ Modem
• Network adapters: T-Mobile Wireless Ethernet Adapter
• Ports: T-Mobile Diagnostics Port.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Device Configuration dialog, make the following settings and click Apply:
• Trace Port: Select the port assigned to T-Mobile Diagnostics Port
• Modem Port: Select the port assigned to T-Mobile HSPA+ Modem
• PS data connection: Select <Automatic>.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
126
Nemo Outdoor Device Configuration Guide
51 ZTE MF880
1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.
2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow
the instructions on the screen. Select Yes in the User Account Control dialog if it
appears.
When the installation is finished, it is important to close the Mobile Broadband
application.
4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Qualcomm item. Click Next.
5. In the Device Configuration dialog, make the following settings and click Apply:
• Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port
• Modem Port: Select the port assigned to ZTE Mobile Broadband Modem
• PS data connection: Select <NDIS>.
6. If the device connecting fails, check that you have selected the correct COM ports and
try again.
127
Nemo Outdoor Device Configuration Guide
52 ZTE TU25
6. Finally click Finish. The driver is now installed. Next, plug in the USB device.
7. Click Continue Anyway until the prompt no longer appears.
128
Nemo Outdoor Device Configuration Guide
8. Next, browse to Start | Control Panel | Hardware and Sound and click on the Device
Manager button. Under Network adapters you should see the ZTE WiMAX BCM1000
item.
9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the Beceem BCS200 (524) item. Click Next.
10. In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port
field in the Device Configuration dialog. Leave the Modem Port field empty.
11. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.
12. If the device connecting fails, check that you have selected the correct COM ports and
try again.
129
Nemo Outdoor Device Configuration Guide
53 Application Tester
These guidelines apply to any commercial terminal, i.e. a terminal not provided by Keysight, that
is used for application testing.
1. First you need to install the connectivity cable driver. The USB connectivity cable driver
and an applicable USB connectivity cable for it will be included in your mobile phone
package. Note! Do not connect the USB connectivity cable to your PC until the
driver installation is complete! Consult the terminal user manual for instructions on
how to install the connectivity cable driver.
2. After installing the connectivity cable driver, go to Start | Control Panel | Phone and
Modem Options | Modems and check the Modem port number assigned to the
terminal. This port number will be the same as the Modem port in Nemo Outdoor.
3. Next you need to create a dial-up connection to the Internet for the modem port
mentioned above. A dial-up networking installation is required before data transfers can
be made. Go to Start | Control Panel | Network Connections. Check to see if the dial-
up connection for your phone was automatically installed with the USB connectivity
driver installation. If not, create a new dial-up connection from File | New Connection.
The dial-up connection you find in the Network Connections window is the same as the
PS data connection in Nemo Outdoor.
4. When the USB connectivity driver and dial-up networking installations are complete, go
to Nemo Outdoor and select Measurement | Add New Device | Phone | Application
Tester. In the Device Configuration dialog select the applicable modem port. The Trace
port field is grayed out. In the PS data connection field, select the dial-up connection
created earlier. Click Apply. If the status field does not say Device is working properly,
check to see that you have selected the right port number and try again.
5. You can also check the earlier chapters in this document for possible similarities to the
installation procedures of your terminal.
130
Nemo Outdoor Device Configuration Guide
54 Technical Support
If you have questions on or beyond this documentation about Nemo tools, please contact our
technical support service through Nemo Support Portal at http://nemo.support.keysight.com,
call us or send us an email at nemo.support@keysight.com. Note that for full support you need
to have the Maintenance Agreement.
131
This information is subject to change without notice.
© Keysight Technologies Finland, Ltd. 2018-2022
Published in USA, July, 2022
NTA00000A-90001
www.keysight.com