Professional Documents
Culture Documents
FC 9071
FC 9071
FC9071
Service Manual
PRODUCT INFORMATION ACCESSORIES
- This product meets the requirements regarding - Nozzle : Tri-Active all purpose nozzle
interference suppression on radio and TV. - Tubes : Metal lacquered telescopic tubes
- After the product has been repaired, it should function - Accessories : Crevice nozzle and small nozzle
properly and has to meet the safety requirements as - Accessory storage : Accessory clip on tube
officially laid down at this moment.
- Coupling : Button coupling
TECHNICAL INFORMATION
OPTIONAL (accessories)
- Colour : Blue bonnet
- FC8021 : S-bag Classic
- Power consumption : 1800 W
- FC8022 : S-bag Clinic
(IEC) 230V
- FC8023 : S-bag Anti-Odour
- Maximum Air displacement : 43 l/s
- FC8025 : S-fresh scent granules
- Vacuum : 300 mbar / 30.0 kPa
- FC8031 : Super Clean Air HEPA filter,
- Type number dustbag : FC8021
HEPA12 exhaust filter
- Duststorage capacity : 3L
- FC8038 : Ultra clean air washable HEPA13
- Cord length : 7m exhaust filter
- Fiter system : Classic S-Bag
long performance
: 3 layer permanent motor
protection filter
: Ultra clean air washable
HEPA13 exhaust filter
- Dimensions of cleaner : 449 x 324 x 250 mm
- Dimensions of packaging : 593 x 393 x 296 mm
- Net weight : 5.7 kg
Published by Philips Consumer Lifestyle Printed in the Netherlands © Copyright reserved Subject to modification
11/05
FC9071
DISASSEMBLY- AND RE-ASSEMBLY ADVISE REPAIR INSTRUCTION
- Cotton dustbags, are used in countries in which paper
- To open the apliance, dustbags are not available.
First remove the filter cover - If the reel half spring unit is replaced, shaft G must be
(item 24) then remove the lubricated with silicone grease. Do not apply any silicone
vario knob button (item 11) grease to or spill any grease on terminals (39) or conductors
with a screwdriver as shown (38).
in the picture. - Item 37 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)
- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn
- Item 10, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.
- To adjust the telescopic tube (item 46) to the required
length, push the adjustment collar in the direction of the
arrow while sliding the top section of the telescopic tube
into or out of the lower section.
- If the function of the electronic control unit (item 15) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust the
pores of the dustbag may become clogged, causing the
- To remove the button panel (item 13), first loosen
passage of air through the dustbag to become obstructed.
mounting screws (A), now by using a screwdriver unlock
As a result, the dustbag-full indicator will indicate that the
the 4 snap connection and separate the panel from the
dustbag needs to be replaced, eventhough the dustbag is not
housing. (see picture)
full at all.
- Display cover (item 12) now can easely be removed from
the button panel.)
- To remove the motor, you need a torx screwdriver with a
14.5cm long shank. Screwdriver 9965 000 08332 can be
used.
ELECTRICAL DIAGRAM
CORD WINDER
Brown
Blue Short-circuit
Triac
Black
M
Black/White
MOTOR
POWER
MODULE
2-7
PARTS LIST
FC9071
= changed
3-7
EXPLODED VIEW
FC9071
A 11
A
12
1 13
3 48
14
Y
Black/
15
White
5 Black
8
6
9 16
10 9
B B brown
blue
Z
55
B
B
B
B
7
4-7
EXPLODED VIEW
FC9071
22
23
C 24
C 25
17
C
C C 26
C
C
C
27
C
28
18
29
19
D 30
20
21
5-7
EXPLODED VIEW
FC9071
31
33
34
Black/
White
Black
Y
35
50
32
36
37
38
F
G
40 , 41+54 E
E
blue Z E
brown
39 F
F
6-7
EXPLODED VIEW
FC9071
43
42
49
45
53 46
51 44
52
47
7-7