Professional Documents
Culture Documents
Macro MRS PQM130
Macro MRS PQM130
Macro MRS PQM130
User's Manual
DO00DDDO
DOOOD OODOOOOOOO
UUUDDOODD
DODD MRSO UUUJUPOM-I3
DOOOOODODO UUULUDO
OO00OOD00OD
DO00ODODO
CN EN P/N:020010140070300
Important Safety Instruction and symbol description
The lightning bolt triangle is used to alert the user to the risk of electric shock.
non-professional qualified technicians do not open TOP OR BOTTOM COVERS
formaintenance
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
1
Foreword
Welcomne
Thank you for purchasing our products.
The PQM series power amplifier is specially
designed for sound system in large stadium, tour,
theater. Please take the time to study this manual
so that youcan obtain the best possible service
from your amplifier.
2
Front panel functions
Front Panel
Suction/
Dust filtering sponge Switch
Control panel
Mounting hole Handel
TEMP Illuminates when amplifier temperature higher than
set protection range.
MUTE Illuminates when either protection circuit action.
VHF Light on when comes with continues
SoNENNAmtay
high frequency signal.
CLIP Illuminates when compressor / limiter is protecting the
amplifier from input overload.
CPL’ Light when the peak current is beyond the scope of
security protection
-5dB-+ Illuminates when output signal around -5dB than full power.
-10dB’lluminates when output signalaround -10dB than full power.
-15dB-’lluminates when output signal around -15dB than full power.
-20dB Illuminates when output signal around -20dB than full power.
SIG’ Iluminates when output signal around +6dB(2V).
POWER + Illuminates when the amplifier start.
CH1-CH2-CH3-CH4 ’ Gain Controller Knob.
3
Rear panelfunctions
Rear Panel
Power cord
MODE SENSITIvITY
RTATT
Speakon output
PEANON
PEAKON 8PEAKON: SPEAKON1
negative/black/nero
6 positivelred/rosso
-positive/red/rosso
negative/black/nero
20mm
0.8
It can work from 8mm
2-16ohm 0.3*
4
System connection cases
MODE n.c.
2
BLACK
n.c
and RED
CH1 CH3
oN
Output with CH3 and CH4 bridged
Remark: When the switch of bridge and parallel
Output with CH1 and CH2 bridged are on bridge is preferential.
inputs from CH1 and Ch3 are effective.
RED
RED
MODE
BLACK
RED
1
Stereo mode
RED
BLACK RAACK
1 n.c.
MODE RED
R
or
CH4
o CH2 CH3
CH1
CH1 CH3 input
Remark : Independent CH4 is effective.
from CH1 or
5
supply
Wiring and AC power
distribution
Power & Wiring
Theamplifier power supply isnt a non-resistance load and its use on unstable music signal, so it can not
calculate with "Voltage xAmpere=Watt" ,the actual power consumption can not be fixed
formula
Dissipation power is tested according to lkHz/82 4 rated power.
Referring to the power dissipation andpower supply/AC of different product forwiring
We suggest the users to match not less than the following wiring size specifications, to obtain the bottor
comprehensive properties.
The Standard Voltage : 220/230V/240V The Standard Voltage :
110/115V/120V
Model Dissipation Power Cable size Model Dissipation Power Cable size
6
Thermal Dissipation
Stack installation
Toensure the cooling environment, please meet the following condition
HotAir
In order to have a good heat
dissipation condition for anplifier,
please clean the filter after you finish
your install, because the dust in filter
willstop the air vent, it's not good for
the heat dissipation. And you should
clean the filter net every month.
CoolAir
oafcoolAN
7
adjustment
PowerLevelof
Procedure
PowerOn
INPUT
GAIN CH MAIN LEVEL
LEVEL
" Input the " Put the line " Put the main " The main output e Adjust the
stable pink output to OdB output to OdB amplitude set input level of
noise should be processor like
"Adjust input displayed the above
gain as: 0 db picture
DO00011I
LINE
GAIN
0
+12dB15 12
-3dB -10 +40 20
OUTPUT
LEVEL LEVEL GAIN LEVEL
Adjust theoutput level of Adjust the volume knob Then adjust the input
processor, the range like and make the output level gain to make the main
the above picture shows within the range as above output less 3dB.
picture shows. "This setting is to ensure
twice power.
Music Audition
Adjust the volume from verv small to loud slowly, after you
ne sound is normal then make it more louder. contirm This step should operated by
When
Output is close to its limit,the CIP light will lights up the speaker professional person, if you don't
Should turn down your volume now. don't let the CUPand you know how to do, please be careful!
time, it means over load, may lights on lon9
damage the system.
8
Specifications
Model POM-13
Output power
80 stereo * 1300Wx4
4Q stereo ** 2100Wx4
20 stereo ** 2500Wx4
89 bridge **
4200Wx2
4Q bridge 5000Wx2
Other Specifications
Frequency response 20Hz-20kHz(+0/-1.5dB)
THD+N s0.05%
S/N rate 280dB
Damping factor 2800
Crosstalk 265dB
Slew rate >10V/us
Input sensitivity 0.775V/1V/1.4V/38d B/32dB/26dB
Input impedance(ba/unbal ) 20k2/1Ok2
Voltage gain (8 ohm ) 42.3dB
Output circuitry Class IM
Cooling Air flow from front to rear
Protection Soft start, VHF, DC, short circuit, over load, clip limit, peak current limit
over heat, progressive volume
Connection
Input Balance input XLR-F, Balance output XLR-M
Output NI4SPEAKON
Function
Front panel indicator Working state, voltage,clip limit, peak current limit , VHE, temp
Rear panel indicator dB/N selector indicator
Front panel Power switch, Volume control
Rear panel Stereo/Parallel/Bridge mode selector switch, Sensitivity selector switch
Dimensions/Weight
Product Dimension (mm) 483x448x89
Packaging Dimension(mm) 595x565x170
G.W. 15.70kg
Power Supply 16A power cord
Product dimension(mm)
418
433
38.5
483
393
Suitable model:PQM-13
notice.
The manufacturer reserves the rights to make changes in specification without prior
The final specification is subiect to the user's manual.
9
Troubleshooting
10