Professional Documents
Culture Documents
AD8667ARMZ - 低噪声,高精密, 16 V , CMOS ,轨至轨运算放大器datasheet
AD8667ARMZ - 低噪声,高精密, 16 V , CMOS ,轨至轨运算放大器datasheet
AD8667ARMZ - 低噪声,高精密, 16 V , CMOS ,轨至轨运算放大器datasheet
06742-001
06742-002
Unity-gain stable NC = NO CONNECT NC = NO CONNECT
Small packages available
3 mm × 3 mm, 8-lead LFCSP Figure 1. 8-Lead SOIC (R-8) Figure 2. 8-Lead LFCSP (CP-8-2)
8-lead MSOP
Other packages
8-lead SOIC OUT A 1 14 OUT D
14-lead SOIC –IN A 2 13 –IN D
OUT A 1 8 V+
14-lead TSSOP –IN A 2 AD8667 7 OUT B +IN A 3 AD8648
AD8669 12 +IN D
TOP VIEW V+ 4 TOP VIEW 11 V–
+IN A 3 (Not to Scale) 6 –IN B
06742-003
(Not to Scale)
+IN B 5 10 +IN C
APPLICATIONS V– 4 5 +IN B
–IN B 6 9 –IN C
06742-004
Sensor front ends OUT B 7 8 OUT C
Transimpedance amplifiers
Figure 3. 8-Lead MSOP (RM-8), Figure 4. 14-Lead SOIC (R-14),
Electrometer applications 8-Lead SOIC (R-8) 14-Lead TSSOP (RU-14)
Photodiode amplification
Low power ADC drivers
Medical diagnostic instruments
pH and ORP meters and probes
DAC or REF buffers
GENERAL DESCRIPTION
The AD866x are rail-to-rail output amplifiers that use the frequency data converters. The low bias current drift is well-
Analog Devices, Inc., patented DigiTrim® trimming technique suited for precision I-to-V converters. The combination of
to achieve low offset voltage. The AD866x feature an extended precision offset, offset drift, and low noise also make the op
operating range with supply voltages up to 16 V. They also amps ideal for gain, dc offset adjust, and active filter in both
feature low input bias current, low input offset voltage, and instrumentation and medical applications. These low power
low current noise. op amps can be used in IR thermometers, pH and ORP instru-
The combination of low offset, very low input bias current, and ments, pressure transducer front ends, and other sensor signal
a wide supply range makes these amplifiers useful in a wide variety conditioning circuits that are used in remote or wireless
of applications usually associated with higher priced JFET ampli- applications.
fiers. Systems using high impedance sensors, such as photodiodes, The AD8663/AD8667/AD8669 are specified over the extended
benefit from the combination of low input bias current, low industrial temperature range of −40°C to +125°C. The single
noise, low offset, and wide bandwidth. AD8663 is available in a narrow 8-lead SOIC package and a very
The ability to operate the device for single (5 V to 16 V) or dual thin, 8-lead LFCSP. The dual AD8667 is available in a narrow
supplies (±2.5 V to ±8 V) supports many applications. The rail- 8-lead SOIC package and an 8-lead MSOP. The quad AD8669
to-rail outputs provide increased dynamic range to drive low is available in a 14-lead SOIC and 14-lead small TSSOP.
Rev. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Tel: 781.329.4700 www.analog.com
Trademarks and registered trademarks are the property of their respective owners. Fax: 781.461.3113 ©2007–2008 Analog Devices, Inc. All rights reserved.
AD8663/AD8667/AD8669
TABLE OF CONTENTS
Features .............................................................................................. 1 Absolute Maximum Ratings ............................................................5
Applications ....................................................................................... 1 Thermal Resistance .......................................................................5
Pin Configurations ........................................................................... 1 ESD Caution...................................................................................5
General Description ......................................................................... 1 Typical Performance Characteristics ..............................................6
Revision History ............................................................................... 2 Outline Dimensions ....................................................................... 13
Specifications..................................................................................... 3 Ordering Guide .......................................................................... 15
Electrical Characteristics ............................................................. 3
REVISION HISTORY
1/08—Rev. A to Rev. B
Added TSSOP ..................................................................... Universal
Change to Table 4 ............................................................................. 5
Changes to Figure 8 and Figure 9 ................................................... 6
Changes to Figure 23 and Figure 26 ............................................... 9
Updated Outline Dimensions ....................................................... 13
Changes to Ordering Guide .......................................................... 15
10/07—Rev. 0 to Rev. A
Added AD8667 and AD8669 ............................................ Universal
Changes to Features.......................................................................... 1
Changes to General Description .................................................... 1
Inserted Figure 3 and Figure 4 ........................................................ 1
Changes to Table 1, Power Supply Section .................................... 3
Changes to Table 2 ............................................................................ 4
Reformatted Typical Performance Characteristics Section ........ 6
Changes to Figure 5 .......................................................................... 6
Changes to Figure 13 ........................................................................ 7
Changes to Figure 17 and Figure 20 ............................................... 8
Inserted Figure 35 Through Figure 39 ......................................... 11
Inserted Figure 40 and Figure 41 .................................................. 12
Updated Outline Dimensions ....................................................... 13
Changes to Ordering Guide .......................................................... 15
Rev. B | Page 2 of 16
AD8663/AD8667/AD8669
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VSY = 5.0 V, VCM = VSY/2, TA = 25°C, unless otherwise noted.
Table 1.
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage VOS VCM = VSY/2 30 175 μV
−40°C < TA < +125°C 450 μV
Input Bias Current IB 0.3 pA
−40°C < TA < +85°C 45 pA
−40°C < TA < +125°C 105 pA
Input Offset Current IOS 0.2 pA
−40°C < TA < +85°C 35 pA
−40°C < TA < +125°C 65 pA
Input Voltage Range 0.2 3.0 V
Common-Mode Rejection Ratio CMRR VCM = 0.2 V to 3.0 V 76 100 dB
−40°C < TA < +125°C 76 100 dB
Large Signal Voltage Gain AVO RL = 100 kΩ, VOUT = 0.5 V to 4.5 V 115 140 dB
RL = 2 kΩ, VOUT = 0.5 V to 4.5 V 106 114 dB
Offset Voltage Drift TCVOS −40°C < TA < +125°C 1.5 5 μV/°C
OUTPUT CHARACTERISTICS
Output Voltage High VOH IL = 100 μA 4.95 4.97 V
−40°C < TA < +125°C 4.90 V
Output Voltage High VOH IL = 1 mA 4.65 4.80 V
−40°C < TA < +125°C 4.60 V
Output Voltage Low VOL IL = 100 μA 17 25 mV
−40°C < TA < +125°C 35 mV
Output Voltage Low VOL IL = 1 mA 150 200 mV
−40°C < TA < +125°C 250 mV
Short-Circuit Current ISC ±7 mA
Closed-Loop Output Impedance ZOUT f = 100 kHz, AV = 1 120 Ω
POWER SUPPLY
Power Supply Rejection Ratio PSRR VSY = 5 V to 16 V 95 105 dB
−40°C < TA < +125°C 95 dB
Supply Current per Amplifier ISY VOUT = VSY/2 210 275 μA
−40°C < TA < +125°C 325 μA
DYNAMIC PERFORMANCE
Slew Rate SR RL = 2 kΩ 0.26 V/μs
Gain Bandwidth Product GBP CL = 20 pF 520 kHz
Phase Margin ΦM CL = 20 pF 60 Degrees
NOISE PERFORMANCE
Peak-to-Peak Noise en p-p f = 0.1 Hz to 10 Hz 2.5 μV p-p
Voltage Noise Density en f = 1 kHz 23 nV/√Hz
f = 10 kHz 21 nV/√Hz
Current Noise Density in f = 1 kHz 0.05 pA/√Hz
Rev. B | Page 3 of 16
AD8663/AD8667/AD8669
VSY = 16.0 V, VCM = VSY/2, TA = 25°C, unless otherwise noted.
Table 2.
Parameter Symbol Conditions Min Typ Max Unit
INPUT CHARACTERISTICS
Offset Voltage VOS VCM = VSY/2 40 300 μV
−40°C < TA < +125°C 500 μV
Input Bias Current IB 0.3 pA
−40°C < TA < +85°C 45 pA
−40°C < TA < +125°C 120 pA
Input Offset Current IOS 0.2 pA
−40°C < TA < +85°C 35 pA
−40°C < TA < +125°C 65 pA
Input Voltage Range 0.2 14.5 V
Common-Mode Rejection Ratio CMRR VCM = 0.2 V to 14.5 V 87 109 dB
−40°C < TA < +125°C 87 109 dB
Large Signal Voltage Gain AVO RL = 100 kΩ, VOUT = 0.5 V to 15.5 V 115 140 dB
RL = 2 kΩ, VOUT = 0.5 V to 15.5 V 106 111 dB
Offset Voltage Drift TCVOS −40°C < TA < +125°C 1.5 5 μV/°C
OUTPUT CHARACTERISTICS
Output Voltage High VOH IL = 100 μA 15.95 15.98 V
−40°C < TA < +125°C 15.90 V
Output Voltage High VOH IL = 1 mA 15.85 15.92 V
−40°C < TA < +125°C 15.80 V
Output Voltage Low VOL IL = 100 μA 17 25 mV
−40°C < TA < +125°C 35 mV
Output Voltage Low VOL IL = 1 mA 70 100 mV
−40°C < TA < +125°C 125 mV
Short-Circuit Current ISC ±50 mA
Closed-Loop Output Impedance ZOUT f = 100 kHz, AV = 1 100 Ω
POWER SUPPLY
Power Supply Rejection Ratio PSRR VSY = 5 V to 16 V 95 105 dB
−40°C < TA < +125°C 95 dB
Supply Current per Amplifier ISY VOUT = VSY/2 230 285 μA
−40°C < TA < +125°C 355 μA
DYNAMIC PERFORMANCE
Slew Rate SR RL = 2 kΩ 0.3 V/μs
Gain Bandwidth Product GBP CL = 20 pF 540 kHz
Phase Margin ΦM CL = 20 pF 64 Degrees
NOISE PERFORMANCE
Peak-to-Peak Noise en p-p f = 0.1 Hz to 10 Hz 2.5 μV p-p
Voltage Noise Density en f = 1 kHz 23 nV/√Hz
f = 10 kHz 21 nV/√Hz
Current Noise Density in f = 1 kHz 0.05 pA/√Hz
Rev. B | Page 4 of 16
AD8663/AD8667/AD8669
Rev. B | Page 5 of 16
AD8663/AD8667/AD8669
NUMBER OF AMPLIFIERS
NUMBER OF AMPLIFIERS
7000
1000
6000
800 5000
4000
600
3000
400
2000
200
1000
0 0
06742-037
06742-005
–250 –200 –150 –100 –50 0 50 100 150 200 250 –250 –200 –150 –100 –50 0 50 100 150 200 250
VOS (µV) VOS (µV)
Figure 5. Input Offset Voltage Distribution Figure 8. Input Offset Voltage Distribution
40 40
VSY = ±2.5V VSY = ±8V
–40°C < TA < +125°C –40°C < TA < +125°C
35 35
30 30
NUMBER OF AMPLIFIERS
NUMBER OF AMPLIFIERS
25 25
20 20
15 15
10 10
5 5
0 0
06742-038
06742-006
0 1 2 3 4 5 0 1 2 3 4 5
TCVOS (µV) TCVOS (µV/°C)
Figure 6. Offset Voltage Drift Distribution Figure 9. Offset Voltage Drift Distribution
500 300
VSY = 5V VSY = 16V
400 TA = 25°C 250 TA = 25°C
200
300
150
200
100
100 50
VOS (µV)
VOS (µV)
0 0
–100 –50
–100
–200
–150
–300
–200
–400 –250
–500 –300
06742-007
06742-010
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 2 4 6 8 10 12 14 16
VCM (V) VCM (V)
Figure 7. Input Offset Voltage vs. Common-Mode Voltage Figure 10. Input Offset Voltage vs. Common-Mode Voltage
Rev. B | Page 6 of 16
AD8663/AD8667/AD8669
100 100
VSY = 5V VSY = 16V
TA = 125°C TA = 125°C
80 80
60 60
IB (pA)
IB (pA)
40 40
20 20
0 0
06742-013
06742-016
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 0.5 2.5 4.5 6.5 8.5 10.5 12.5 14.5
VCM (V) VCM (V)
Figure 11. Input Bias Current vs. Common-Mode Voltage at 125°C Figure 14. Input Bias Current vs. Common-Mode Voltage at 125°C
100 100
VSY = 5V VSY = 16V
TA = 25°C TA = 25°C
90 90
80 80
70 70
CMRR (dB)
CMRR (dB)
60 60
50 50
40 40
30 30
20 20
06742-023
06742-039
100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 12. CMRR vs. Frequency, VSY = 5 V Figure 15. CMRR vs. Frequency, VSY = 16 V
10000 10000
VSY = 5V VSY = 16V
TA = 25°C TA = 25°C
OUTPUT SATURATION VOLTAGE (mV)
1000 1000
100 100
VSY – VOH SOURCING VSY – VOH SOURCING
VOL SINKING
10 10 VOL SINKING
1 1
0.1 0.1
06742-011
06742-014
Figure 13. Output Swing Saturation Voltage vs. Load Current Figure 16. Output Swing Saturation Voltage vs. Load Current
Rev. B | Page 7 of 16
AD8663/AD8667/AD8669
350 140
300 120
VSY – VOH @ 1mA
VSY – VOH @ 1mA
DROP OUT VOLTAGE (mV)
200 80
VOL @ 1mA VOL @ 1mA
150 60
100 40
0 0
06742-044
06742-045
–40 –25 –10 5 20 35 50 65 80 95 110 125 –40 –25 –10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C) TEMPERATURE (°C)
Figure 17. Output Voltage Saturation vs. Temperature Figure 20. Output Voltage Saturation vs. Temperature
120 120
100 100
GAIN (dB) AND PHASE (Degrees)
60 60
40 40
GAIN CL = 0pF GAIN CL = 0pF
20 20
0 0
–20 –20
–40 –40
CL = 200pF CL = 200pF
–60 VSY = 5V –60 VSY = 16V
TA = 25°C TA = 25°C
–80 –80
06742-020
06742-017
Figure 18. Open-Loop Gain and Phase Shift vs. Frequency Figure 21. Open-Loop Gain and Phase Shift vs. Frequency
60 60
VSY = 5V VSY = 16V
TA = 25°C TA = 25°C
G = 100 G = 100
40 40
G = 10 G = 10
20 20
ACL (dB)
ACL (dB)
G=1 G=1
0 0
–20 –20
–40 –40
06742-021
06742-018
Figure 19. Closed-Loop Gain vs. Frequency Figure 22. Closed-Loop Gain vs. Frequency, VSY = 16 V
Rev. B | Page 8 of 16
AD8663/AD8667/AD8669
1000 1000
G = 100 G = 100
100 G = 10 100 G = 10
VSY = 5V VSY = 16V
TA = 25°C TA = 25°C
G=1 G=1
ZOUT (Ω)
ZOUT (Ω)
10 10
1 1
0.1 0.1
06742-040
06742-041
100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 23. Closed-Loop Output Impedance vs. Frequency, VSY = 5 V Figure 26. Closed-Loop Output Impedance vs. Frequency, VSY = 16 V
90 90
VSY = 5V VSY = 16V
80 TA = 25°C 80 TA = 25°C
70 70
60 60
50 50
PSRR (dB)
PSRR (dB)
40 40
30 30
PSSR+ PSSR–
20 20
10 10
0 0
PSSR+
–10 PSSR– –10
–20 –20
06742-024
06742-027
100 1k 10k 100k 1M 10M 100 1k 10k 100k 1M 10M
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 24. PSRR vs. Frequency, VSY = 5 V Figure 27. PSRR vs. Frequency, VSY = 16 V
80 80
VSY = 5V VSY = 16V
TA = 25°C TA = 25°C
70 70
60 60
OVERSHOOT (%)
OVERSHOOT (%)
50 OS– 50 OS+
40 40
30 OS+ 30
OS–
20 20
10 10
0 0
06742-028
06742-025
10 100 1k 10 100 1k
CAPACITANCE (pF) CAPACITANCE (pF)
Figure 25. Small-Signal Overshoot vs. Load Capacitance, VSY = 5 V Figure 28. Small-Signal Overshoot vs. Load Capacitance, VSY = 16 V
Rev. B | Page 9 of 16
AD8663/AD8667/AD8669
VSY = ±8V
AV = 1
CL = 200pF
RL = 2kΩ
VOLTAGE (200mV/DIV)
VOLTAGE (2V/DIV)
VSY = ±2.5V
AV = 1
CL = 200pF
RL = 2kΩ
06742-032
06742-029
TIME (10µs/DIV) TIME (20µs/DIV)
Figure 29. Large Signal Transient Response, VSY = ±2.5 V Figure 32. Large Signal Transient Response, VSY = ±8 V
VOLTAGE (50mV/DIV)
06742-030
06742-033
TIME (2µs/DIV) TIME (2µs/DIV)
Figure 30. Small Signal Transient Response, VSY = ±2.5 V Figure 33. Small Signal Transient Response, VSY = ±8 V
300 1200
TA = +125°C
TA = +25°C TA = +85°C
200 800
TA = –40°C TA = +25°C
ISY (µA)
ISY (µA)
150 600
TA = –40°C
100 400
50 200
0 0
06742-042
06742-043
0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16
VSY (V) VSY (V)
Figure 31. AD8663, Supply Current vs. Supply Voltage Figure 34. AD8669, Supply Current vs. Supply Voltage
Rev. B | Page 10 of 16
AD8663/AD8667/AD8669
600 1000
+125°C VSY = ±2.5V AND ±8V
550 TA = 25°C
+85°C
500
+25°C
450
400 100
–40°C
en (nV/ Hz)
350
ISY (µA)
300
250
200 10
150
100
50
0 1
06742-031
06742-034
0 2 4 6 8 10 12 14 16 1 10 100 1000 10000
VSY (V)
FREQUENCY (Hz)
Figure 35. AD8667, Supply Current vs. Supply Voltage Figure 38. Voltage Noise Density
06742-046
–0.25 –3.5 –0.25 –13
TIME (20µs/DIV) TIME (20µs/DIV)
Figure 36. Positive Overload Recovery Figure 39. Positive Overload Recovery
VSY = ±2.5V
06742-048
Figure 37. Negative Overload Recovery Figure 40. Negative Overload Recovery
Rev. B | Page 11 of 16
AD8663/AD8667/AD8669
0 0
20kΩ VSY = ±2.5V 20kΩ VSY = ±8V
–20 TA = 25°C –20 TA = 25°C
2kΩ 2kΩ
CHANNEL SEPARATION (dB)
–60 –60
–80 –80
–100 –100
–120 –120
–140 –140
–160 –160
06742-051
06742-047
100 1k 10k 100k 100 1k 10k 100k
FREQUENCY (Hz) FREQUENCY (Hz)
Figure 41. Channel Separation vs. Frequency Figure 42. Channel Separation vs. Frequency
Rev. B | Page 12 of 16
AD8663/AD8667/AD8669
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8 5
4.00 (0.1574) 6.20 (0.2441)
3.80 (0.1497) 1 5.80 (0.2284)
4
012407-A
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
3.25
3.00 SQ 0.60 MAX
0.50
2.75 BSC
0.60 MAX
5 8
2.95
1.60
TOP 2.75 SQ EXPOSED
PIN 1 PAD 1.45
INDICATOR VIEW 2.55 (BOTTOM VIEW) 1.30
4 1
PIN 1
0.50 INDICATOR
0.40 1.89
12° MAX 0.70 MAX 0.30 1.74
0.90 MAX 0.65 TYP 1.59
0.85 NOM 0.05 MAX
0.01 NOM
SEATING 0.30
PLANE 0.23 0.20 REF
061507-B
0.18
Rev. B | Page 13 of 16
AD8663/AD8667/AD8669
3.20
3.00
2.80
8 5 5.15
3.20
4.90
3.00
4.65
2.80 1
4
PIN 1
0.65 BSC
0.95
0.85 1.10 MAX
0.75
0.80
0.15 0.38 8° 0.60
0.23
0.00 0.22 0° 0.40
0.08
COPLANARITY SEATING
0.10 PLANE
8.75 (0.3445)
8.55 (0.3366)
14 8
4.00 (0.1575) 6.20 (0.2441)
1
3.80 (0.1496) 7 5.80 (0.2283)
14 8
4.50
4.40 6.40
BSC
4.30
1 7
PIN 1
1.05 0.65
1.00 BSC
0.20
0.80 1.20
MAX 0.09 0.75
8° 0.60
0.15 0.30 0° 0.45
0.05 SEATING
0.19 PLANE COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-153-AB-1
Rev. B | Page 14 of 16
AD8663/AD8667/AD8669
ORDERING GUIDE
Model Temperature Range Package Description Package Option Branding
AD8663ARZ 1 −40°C to +125°C 8-Lead SOIC_N R-8
AD8663ARZ-REEL1 −40°C to +125°C 8-Lead SOIC_N R-8
AD8663ARZ-REEL71 −40°C to +125°C 8-Lead SOIC_N R-8
AD8663ACPZ-R21 −40°C to +125°C 8-Lead LFCSP_VD CP-8-2 A1U
AD8663ACPZ-REEL1 −40°C to +125°C 8-Lead LFCSP_VD CP-8-2 A1U
AD8663ACPZ-REEL71 −40°C to +125°C 8-Lead LFCSP_VD CP-8-2 A1U
AD8667ARZ1 −40°C to +125°C 8-Lead SOIC_N R-8
AD8667ARZ-REEL1 −40°C to +125°C 8-Lead SOIC_N R-8
AD8667ARZ-REEL71 −40°C to +125°C 8-Lead SOIC_N R-8
AD8667ARMZ-R21 −40°C to +125°C 8-Lead MSOP RM-8 A1E
AD8667ARMZ-REEL1 −40°C to +125°C 8-Lead MSOP RM-8 A1E
AD8669ARZ1 −40°C to +125°C 14-Lead SOIC_N R-14
AD8669ARZ-REEL1 −40°C to +125°C 14-Lead SOIC_N R-14
AD8669ARZ-REEL71 −40°C to +125°C 14-Lead SOIC_N R-14
AD8669ARUZ1 −40°C to +125°C 14-Lead TSSOP RU-14
AD8669ARUZ-REEL1 −40°C to +125°C 14-Lead TSSOP RU-14
1
Z = RoHS Compliant Part.
Rev. B | Page 15 of 16
AD8663/AD8667/AD8669
NOTES
Rev. B | Page 16 of 16