Professional Documents
Culture Documents
Trim and Upholstery
Trim and Upholstery
Trim and Upholstery
"The repair procedures given by the manufacturer in this document are based on the All rights reserved by Renault.
technical specifications current when it was prepared.
Copying or translating, in part or in full, of this document or use of the service part reference
The procedures may be modified as a result of changes introduced by the manufacturer in numbering system is forbidden without the prior written authority of Renault.
the production of the various component units and accessories from which the vehicles are
constructed".
Contents
Pages
136664
1-2/3 REAR BENCH SEAT + ARMREST + N/R a Remove:
SEATBACK
- the clips (1) ,
a Remove the 1/3 and 2/3 rear bench seat base (see
- the mounting supports of the rear bench seat base
1/3 and 2/3 rear bench seat base: Removal - Re-
(2) .
fitting) .
a Remove:
- the front door sill lining (see 71A, Body internal
trim, Front door sill lining: Removal - Refitting,
page 71A-12) ,
- the rear door sill lining (see 71A, Body internal
trim, Rear door sill lining: Removal - Refitting,
page 71A-15) ,
- the rear inner sill upper trim (see Rear inner sill
upper trim: Removal - Refitting) ,
- the B-pillar lower trim (see 71A, Body internal
135098
trim, B-pillar lower trim: Removal - Refitting,
page 71A-14) . a Remove the clips (3) .
71A-1
BODY INTERNAL TRIM
Floor carpet: Removal - Refitting 71A
- the accelerator pedal stop (5) ,
II - FINAL OPERATION
a Refit:
- the rear inner sill upper trim (see Rear inner sill
upper trim: Removal - Refitting) ,
a Refit the 1/3 and 2/3 rear bench seat base (see 1/3
and 2/3 rear bench seat base: Removal - Refit-
ting) .
a Refit the single unit rear bench seat base (see Sin-
gle unit rear bench seat base: Removal - Refit-
ting) .
135097
a Remove:
- the accelerator pedal stop (5) ,
a Refit:
- the floor carpet.
- the central console (see Centre console: Remov-
REFITTING al - Refitting) (57A, Interior equipment),
71A-2
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B32
IMPORTANT
REMOVAL
ELECTRIC SUNROOF
I - REMOVAL PREPARATION OPERATION a Disconnect the sunroof wiring connectors.
a Disconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
ELECTRIC SUNROOF
a Remove the sunroof switch (see Sunroof switch:
Removal - Refitting) (52A, Non-side opening ele-
ment mechanisms).
a Remove:
- the interior lights (see Interior light: Removal -
Refitting) (81B, Interior lighting),
- the sun visors (see Sun visor: Removal - Refit-
ting) (57A, Interior equipment),
- the courtesy lights (see Courtesy light: Removal -
Refitting) (81B, Interior lighting),
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-18) .
71A-3
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B32
ELECTRIC SUNROOF
137004
137172
a Remove: a Remove the 1/3 and 2/3 rear bench seat base (see
1/3 and 2/3 rear bench seat base: Removal - Re-
- the upper cover of the interior rear view mirror (3)
fitting) .
using the tool (Car. 1363),
- the lower cover of the interior rear view mirror.
a Disconnect the connectors (4) on the interior rear
view mirror. a Remove:
- the side door seals partially,
- the luggage compartment seal partially,
- the B-pillar lower trims (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-14) ,
71A-4
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B32
- the B-pillar upper trims (see 71A, Body internal
trim, B-pillar upper trim: Removal - Refitting,
page 71A-19) ,
137482
a Unclip the headlining central section (7) .
137511
137175
a Unclip the rear mountings.
a Remove the headlining (this operation requires two
people).
ELECTRIC SUNROOF
a
Note:
For vehicles equipped with a sunroof, the head-
lining must be handled with care. The side edges
are weakened by the design of the sunroof.
137174
71A-5
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B32
Note:
For vehicles equipped with a sunroof, the head-
lining must be handled with care. The side edges
are weakened by the design of the sunroof.
a Clip on:
137482
III - FINAL OPERATION
a Refit:
a Refit the 1/3 and 2/3 rear bench seat base (see 1/3
and 2/3 rear bench seat base: Removal - Refit-
ting) .
71A-6
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
B32
ELECTRIC SUNROOF
a Refit the finishing seal.
ELECTRIC SUNROOF
a Connect the sunroof wiring connectors.
a Refit:
- the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-18) ,
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the courtesy lights (see Courtesy light: Removal -
Refitting) (81B, Interior lighting),
- the sun visors (see Sun visor: Removal - Refit-
ting) (57A, Interior equipment),
- the interior lights (see Interior light: Removal -
Refitting) (81B, Interior lighting).
ELECTRIC SUNROOF
a Refit the sunroof switch (see Sunroof switch: Re-
moval - Refitting) (52A, Non-side opening element
mechanisms).
71A-7
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
L38
IMPORTANT
I - PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
a Remove:
- the sun visors (see Sun visor: Removal - Refit-
ting) (57A, Interior equipment),
- the interior lights (see Interior light: Removal -
Refitting) (81B, Interior lighting),
- the courtesy lights (see Courtesy light: Removal -
Refitting) (81B, Interior lighting),
- the grab handles (see Grab handle: Removal -
Refitting) (57A, Interior equipment),
- the windscreen pillar trims (see 71A, Body inter-
nal trim, Windscreen pillar trim: Removal - Re-
fitting, page 71A-18) .
71A-8
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
L38
II - REMOVAL OPERATION
ELECTRIC SUNROOF
144071
137503 a Unclip:
ELECTRIC SUNROOF
a Disconnect:
144086
a Remove:
71A-9
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
L38
REFITTING
144090
a Unclip the headlining central section (7) .
ELECTRIC SUNROOF
a
Note:
For vehicles equipped with a sunroof, the head-
lining must be handled with care. The side edges 144087
are weakened by the design of the sunroof.
144088
a Check the presence and the condition of the velcro
strips (8) .
71A-10
BODY INTERNAL TRIM
Headlining: Removal - Refitting 71A
L38
II - REFITTING OPERATION
ELECTRIC SUNROOF
a
Note:
For vehicles equipped with a sunroof, the head-
lining must be handled with care. The side edges
are weakened by the design of the sunroof.
71A-11
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting 71A
II - OPERATION FOR REMOVAL OF PART
Special tooling required CONCERNED
Car. 1363 Set of trim removal levers.
REMOVAL
138755
a Remove the front door sill lining (2) , using the tool
(Car. 1363).
138756
a Remove:
- the front side door seal partially,
- the bonnet release control (1) from the left-hand
side, using the tool (Car. 1363),
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-14) .
71A-12
BODY INTERNAL TRIM
Front door sill lining: Removal - Refitting 71A
II - FINAL OPERATION
a Refit:
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-14) ,
- the bonnet release control (1) from the left-hand
side,
- the front side door seal.
138757
137117
REFITTING
a Refit:
71A-13
BODY INTERNAL TRIM
B-pillar lower trim: Removal - Refitting 71A
REMOVAL REFITTING
137107
137109
a Remove the B-pillar lower trim at (1) and (2) .
71A-14
BODY INTERNAL TRIM
Rear door sill lining: Removal - Refitting 71A
REMOVAL II - OPERATION FOR REMOVAL OF PART
CONCERNED
137099
137102
a Remove:
- the clip (1) ,
REFITTING
71A-15
BODY INTERNAL TRIM
Rear door sill lining: Removal - Refitting 71A
a Refit the clip (1) .
II - FINAL OPERATION
a Refit:
- the rear inner sill upper trim (see Rear inner sill
upper trim: Removal - Refitting) ,
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-14) .
71A-16
BODY INTERNAL TRIM
Rear wheel arch trim: Removal - Refitting 71A
B32
REMOVAL - the rear end panel trim (see Rear end panel lin-
ing: Removal - Refitting) .
137096
a Remove the rear wheel arch trim (1) .
REFITTING
II - FINAL OPERATION
a Refit the rear parcel shelf side trim (see 71A, Body
internal trim, Rear parcel shelf side trim: Remov-
al - Refitting, page 71A-25) .
a Refit:
- the rear inner sill upper trim (see Rear inner sill
upper trim: Removal - Refitting) ,
71A-17
BODY INTERNAL TRIM
Windscreen pillar trim: Removal - Refitting 71A
Special tooling required
REFITTING
Car. 1363 Set of trim removal levers. I - REFITTING OPERATION FOR PART
CONCERNED
REMOVAL a Insert the lower section of the windscreen pillar trim.
a Clip on the entire length of the A-pillar trim.
138799
138800
71A-18
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
Tightening torquesm
REMOVAL
139020
139018
a Unclip the trim by pressing on the locking clips (1)
using a flat-blade screwdriver.
a Remove the trim (2) .
71A-19
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
137457
a Remove:
137438
- the bolt (3) , a Use a flat-blade screwdriver to press at (7) to re-
- the front side seat belt return mechanism. lease the lower section of the trim.
137036 137072
a Remove: a Remove the clips (9) .
- the bolt (4) , a Unclip the lower section of the B-pillar upper trim.
- the guide of the front side seat belt return mecha-
nism.
71A-20
BODY INTERNAL TRIM
B-pillar upper trim: Removal - Refitting 71A
139024
a Remove the B-pillar upper trim at (10) and (11) .
REFITTING
II - FINAL OPERATION
a Refit the guide of the front side seat belt return
mechanism.
a Refit the front side seat belt return mechanism.
a Torque tighten the bolt of the front side seat belt
return mechanism (21 N.m).
a Refit:
- the trim of the front side seat belt return mecha-
nism,
- the B-pillar lower trim (see 71A, Body internal
trim, B-pillar lower trim: Removal - Refitting,
page 71A-14) .
71A-21
BODY INTERNAL TRIM
Quarter panel trim: Removal - Refitting 71A
B32
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Tightening torquesm
REMOVAL
137450
REFITTING
II - FINAL OPERATION
a Torque tighten the bolt of the rear side seat belt
lower mounting (21 N.m).
a Refit:
- the rear inner sill upper trim (see Rear inner sill
upper trim: Removal - Refitting) ,
- the rear parcel shelf side trim (see 71A, Body in-
ternal trim, Rear parcel shelf side trim: Removal
- Refitting, page 71A-25) .
71A-22
BODY INTERNAL TRIM
Quarter panel trim: Removal - Refitting 71A
L38
REMOVAL
a Partially unclip the rear door sill upper trim (see Rear
inner sill upper trim: Removal - Refitting) .
II - REMOVAL OPERATION
143767
143766
REFITTING
I - REFITTING OPERATION
a Refit the rear quarter panel trim.
II - FINAL OPERATION
a Clip on the rear door sill upper trim (see Rear inner
sill upper trim: Removal - Refitting) .
a Fit the rear bench seatback.
71A-23
BODY INTERNAL TRIM
Rear panel lining: Removal - Refitting 71A
L38
REMOVAL
II - REMOVAL OPERATION
144143
a Remove:
- the clips (1) using the tool (Car. 1363),
- the trim (2) using the tool (Car. 1363),
- the rear panel trim.
REFITTING
II - REFITTING OPERATION
a Proceed in the reverse order to removal.
71A-24
BODY INTERNAL TRIM
Rear parcel shelf side trim: Removal - Refitting 71A
B32
REMOVAL REFITTING
137439
137441
a Remove:
- the bolts (1) ,
- the rear parcel shelf side trim (2) .
71A-25
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
Special tooling required
REMOVAL
137394
a Remove the rear view mirror interior trim.
137392
a Remove the trim of the front side door handle using
the tool (Car. 1363) by inserting it at (1) .
139034
a Remove the blanking cover (4) .
72A-1
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
II - OPERATION FOR REMOVAL OF PART
CONCERNED
EQUIPMENT LEVEL EA1 or EQUIPMENT LEVEL
EA2
EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL
EA4
137405
a Remove the bolts (5) .
137407
a Remove the bolts (5) .
139012
a Unclip the front side door trim.
a Disconnect:
- the connectors of the front side door window con-
trol switch plate,
- the front side door light.
72A-2
SIDE OPENING ELEMENT TRIM
Front side door trim: Removal - Refitting 72A
a Unclip the front side door interior opening control ca-
ble.
a Remove the front side door trim.
REFITTING
72A-3
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B32
REMOVAL
137396
137399
137398
a Unclip the clip (2) .
a Remove the manual window winder control handle.
137400
a Pull the ring towards the vehicle interior (1) .
72A-4
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B32
II - OPERATION FOR REMOVAL OF PART
CONCERNED
142218
a Remove the bolt (3) from the rear side door trim.
139015
a Unclip:
- the rear side door trim,
- the interior opening release cable of the rear side
door.
139034
RADIO 03A or RADIO 05A
a Remove:
a Disconnect the tweeter speaker.
- the blanking cover (6) ,
- the bolt (7) .
72A-5
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
B32
III - FINAL OPERATION
a Refit:
- the bolt (7)
- the blanking cover (6) .
a Refit the bolt (3) of the rear side door trim.
Note:
Refit the manual window winder handle for the
rear side door in a vertical position with the but-
ton at the bottom.
139016
a Remove the rear side door trim. a Carry out a function test.
REFITTING
a Clip on:
72A-6
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
L38
REMOVAL
137396
137399
137398
a Unclip the clip (2) .
a Remove the manual window winder control handle.
137400
72A-7
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
L38
II - REMOVAL OPERATION
143835
a Remove: 140837
- the side bolt of the rear side door trim (3) , a Partially unclip the rear side door trim using unclip-
ping pliers at (6) .
- the blanking cover (4) ,
a Disconnect the connector from the rear side door
- the bolt of the rear side door opening handle, tweeter.
- the rear side door opening handle (5) .
a Remove the rear side door trim.
REFITTING
II - REFITTING OPERATION
a Connect:
a Unclip the window winder plate of the rear side door a Clip on:
using the tool (Car. 1363).
- the rear side door window winder plate,
a Disconnect the connector of the rear side door win-
dow winder. - the rear side door trim.
72A-8
SIDE OPENING ELEMENT TRIM
Rear side door trim: Removal - Refitting 72A
L38
III - FINAL OPERATION
Note:
Refit the manual window winder handle for the
rear side door in a vertical position with the but-
ton at the bottom.
72A-9
NON-SIDE OPENING ELEMENTS TRIM
Tailgate trim: Removal - Refitting 73A
B32
REMOVAL
137385
a Remove the centre trim. 137391
a Remove:
- the bolts (1) ,
- the tailgate trim.
REFITTING
Note:
Always check the condition of the clips and
replace them if necessar y.
73A-1
NON-SIDE OPENING ELEMENTS TRIM
Luggage compartment lid trim: Removal - Refitting 73A
L38
a Remove the boot lid trim.
Special tooling required
II - REFITTING OPERATION
a Proceed in the reverse order to removal.
143945
144142
a Unclip the clips (2) of the side trims using the tool
(Car. 1363).
a Remove the side trims.
73A-2
FRONT SEAT FRAMES AND MECHANISMS
Front seat base frame: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Note:
It is prohibited to carry out any welding operation on
the frames of the seat and bench seat. II - REMOVAL OPERATION
REMOVAL
a Remove:
- the front seat base trim (see 77A, Front seat trim, - the bolts (1) from the front seat « seatback - seat
Front seat base trim: Removal - Refitting, page base » frame,
77A-1) , - the front seat base frame.
- the front seat belt buckle stalk (see Front seat belt
buckle: Removal - Refitting) (88C, Airbag and REFITTING
pretensioners),
- the side airbag (see Front (chest-level) side air- I - REFITTING PREPARATION OPERATION
bag: Removal - Refitting) , a parts always to be replaced: Front seatback
frame mounting on front seat base frame (70,08,
- the front seat lap belt pretensioner (see Front seat
02,09).
lap belt pretensioner: Removal - Refitting)
- the front seat runners (see 75A, Front seat frames II - REFITTING OPERATION
and mechanisms, Front seat runner: Removal -
Refitting, page 75A-4) . a Proceed in the reverse order to removal.
a Torque tighten the new bolts for the « seatback -
- the electrical wiring, seat base » frame on the front seat (40 N.m).
- the front seat base pad. a Carry out a function test.
75A-1
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Note: a Remove:
It is prohibited to carry out any welding operation on - the front seat headrest guides (see 79A, Seat ac-
the frames of the seat and bench seat. cessories, Front seat headrest guide: Removal
- Refitting, page 79A-4) ,
- the front seatback « foam - cover » assembly (see
77A, Front seat trim, Front seatback trim: Re-
Note: moval - Refitting, page 77A-4) ,
Depending on the method of sale defined by the - the front side (chest-level) airbag (see Front
Parts Department, adaptations can be made to the (chest-level) side airbag: Removal - Refitting)
seat frames. (88C, Airbags and pretensioners).
In this case, it is permitted to eliminate certain com-
ponents (supports, wires, brackets, inserts, etc)
FRONT ARMREST, and FRONT SEAT TYPE 05 or
depending on vehicle type.
FRONT SEAT TYPE 06
a Remove the front seat lumbar adjustment mecha-
REMOVAL nism (see 75A, Front seat frames and mecha-
nisms, Front seat lumbar adjustment: Removal -
Refitting, page 75A-9) .
I - REMOVAL PREPARATION OPERATION
a Disconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
a Remove the lumbar pad of the front seatback.
a Remove:
- the front seat headrest (see 79A, Seat accesso-
ries, Front headrest: Removal - Refitting, page
79A-1) ,
- the compete front seat (see 75A, Front seat
frames and mechanisms, Complete front seat:
Removal - Refitting, page 75A-13) ,
- the front seat lower casings (see 77A, Front seat
trim, Front seat lower casing: Removal - Refit-
ting, page 77A-12) .
75A-2
FRONT SEAT FRAMES AND MECHANISMS
Front seatback frame: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REMOVAL OPERATION
138050
a Remove:
- the bolts (1) from the front seat « seatback - seat
base » frame,
- the front seatback frame.
REFITTING
II - REFITTING OPERATION
a Refit the front seatback frame.
a Torque tighten the new bolts for the « seatback -
seat base » frame on the front seat (40 N.m).
75A-3
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REMOVAL OPERATION
Equipment required
Diagnostic tool
Tightening torquesm
REMOVAL
IMPORTANT
To avoid a fault with or even triggering of pyro-
technic components (airbags or pretensioners),
check the airbag computer using the diagnostic 144148
tool.
REFITTING
75A-4
FRONT SEAT FRAMES AND MECHANISMS
Front seat runner: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REFITTING OPERATION
a Refit the front seat runners.
a Finger tighten all the attachments.
139548
a Position the runners so that there is a centre-to-cen-
tre distance of 428.5 mm between the two rear
mountings.
a Torque tighten the new nuts of the front seat "seat
base - runner" frame (21 N.m).
75A-5
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjuster control: Removal - Refitting 75A
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05, and
EXPORT EQUIPMENT LEVEL ADDITIONAL
Tightening torquesm
REMOVAL
143962
a Unclip the front seat belt using a flat-blade screw-
driver at (2) .
a Remove the front seatback angle control (see 75A,
Front seat frames and mechanisms, Front seat
backrest tilt control: Removal - Refitting, page
75A-12) .
143963
a Move aside the seat belt protector (1) .
75A-6
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjuster control: Removal - Refitting 75A
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 03 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05, and
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - OPERATION FOR REMOVAL OF PART
CONCERNED
143775
143773
a Move aside the exterior casing of the front seat base
(5) so that the bolts (6) can be accessed.
a Remove:
- the bolts (6) of the front seat height adjustment
control,
- the front seat height adjustment control (7) .
REFITTING
75A-7
FRONT SEAT FRAMES AND MECHANISMS
Front seat height adjustment: Removal - Refitting 75A
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 04 or FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06, and
EXPORT EQUIPMENT LEVEL ADDITIONAL
138033
a
Note:
The torsion bar is used again on the front seat
height adjustment mechanism.
The front seat height adjustment mechanism
cannot be removed.
The Parts Department supplies the front seat
frame assembled with the front seat height
adjustment mechanism.
75A-8
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting 75A
FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06, and EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
138051
a Remove the bolt (1) from the front seat lumbar ad-
justment mechanism.
Note:
For this operation, the lumbar pad must be loose.
75A-9
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment: Removal - Refitting 75A
FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06, and EXPORT EQUIPMENT LEVEL ADDITIONAL
REFITTING
138053
a
Note:
The lumbar pad springs on the front seatback
frame are positioned with the hook facing
towards the rear.
75A-10
FRONT SEAT FRAMES AND MECHANISMS
Front seat lumbar adjustment control: Removal - Refitting 75A
FRONT SEAT TYPE 05 or FRONT SEAT TYPE 06, and EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
REMOVAL OPERATION
144145
a Unclip the front seat lumbar adjustment control (1) .
REFITTING
a Clip on the lumbar adjustment control.
a Carry out a function test.
Note:
The vertical position (upwards) of the control cor-
responds to a relaxed pad.
75A-11
FRONT SEAT FRAMES AND MECHANISMS
Front seat backrest tilt control: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
REMOVAL OPERATION
143771
a Unclip the front seatback angle control at (1) using
the tool (Car. 1363).
REFITTING
I - REFITTING OPERATION
a Clip on the front seatback angle control.
II - FINAL OPERATION
a Carry out a function test.
75A-12
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Tightening torquesm
REMOVAL
a Adjust:
139314
75A-13
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
143963 139317
Note:
Hold the wiring mounting to avoid breaking its
indexing guide (5) , when disconnecting the con-
nector from the front seat wiring.
REFITTING
75A-14
FRONT SEAT FRAMES AND MECHANISMS
Complete front seat: Removal - Refitting 75A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Driver's side III - FINAL OPERATION
a Adjust the following to their original positions:
- the height and the depth of the steering wheel,
- the front seatback angle,
- the front seat base height.
a Remove the masking tape from the front door sill lin-
ing.
139316
Passenger side
139316
a Clip the front seat belt into the lap belt pretensioner.
75A-15
REAR SEAT FRAMES AND MECHANISMS
Rear bench seatback: Removal - Refitting 76A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Tightening torquesm
REMOVAL
II - REMOVAL OPERATION
144118
a Remove the rear seat belt buckle bolt (1) . 144119
a Remove the bolts (3) from the 2/3 rear bench seat-
back.
76A-1
REAR SEAT FRAMES AND MECHANISMS
Rear bench seatback: Removal - Refitting 76A
EXPORT EQUIPMENT LEVEL ADDITIONAL
FOLDING REAR BENCH SEAT 1-2/3 REAR BENCH SEAT + ARMREST + N/R
SEATBACK
144119
a Remove the bolt (4) from the rear bench seatback 142704
on each side. a Release the 1/3 rear bench seatback from the anti-
release pins at (5) .
a Remove the 1/3 rear bench seatback at (6) .
144386
a Release the 2/3 rear bench seatback from the anti-
release pins at (7) .
a Remove the 2/3 rear bench seatback at (8) .
76A-2
REAR SEAT FRAMES AND MECHANISMS
Rear bench seatback: Removal - Refitting 76A
EXPORT EQUIPMENT LEVEL ADDITIONAL
144356
a Release the rear bench seatback from the anti-re-
lease pins at (9) on each side.
a Remove the rear bench seatback at (10) on each
side.
REFITTING
II - REFITTING OPERATION
a Proceed in the reverse order to removal.
a Torque tighten:
- the bolts of the rear bench seatback (21 N.m),
- the rear seat belt buckle bolt (21 N.m).
76A-3
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat base: Removal - Refitting 76A
EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
143952
a Tilt the 2/3 rear bench seat base.
II - REMOVAL OPERATION
136700
a Tilt the single unit rear bench seat base.
136702
a Unclip the single unit rear bench seat base.
143944
a Tilt the 1/3 rear bench seat base.
76A-4
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat base: Removal - Refitting 76A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - FINAL OPERATION
1-2/3 REAR BENCH SEAT + ARMREST + N/R a Pull down the rear bench seat base.
SEATBACK
136709
136715
REFITTING
I - REFITTING OPERATION
76A-5
REAR SEAT FRAMES AND MECHANISMS
Rear bench seat mechanism: Removal - Refitting 76A
FOLDING REAR BENCH SEAT or 1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK
- the cover of the rear bench seatback (see 78A,
Rear seat trim, 1/3 and 2/3 rear bench seatback
Tightening torquesm trim: Removal - Refitting, page 78A-1) .
137427
a Remove:
FOLDING REAR BENCH SEAT
- the bolts (1) of the rear bench seatback locking
a Remove the cover from the rear bench seatback
mechanism,
(see Single unit rear bench seatback trim: Re-
moval - Refitting) . - the locking mechanism of the rear bench seatback
(2) .
REFITTING
1-2/3 REAR BENCH SEAT + ARMREST + N/R a Proceed in reverse order to removal.
SEATBACK a Torque tighten the bolts of the rear bench seat-
a Remove the rear bench seatback (see 76A, Rear back locking mechanism (18 N.m).
seat frames and mechanisms, Rear bench seat- a Carry out a function test.
back: Removal - Refitting, page 76A-1) .
76A-6
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting 77A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Equipment required
Diagnostic tool
IMPORTANT
To prevent any accidental triggering whilst working
on or near a passive safety element, apply the pro-
cedure for deactivating the safety systems (see Air-
bags and pretensioners: Precautions for the repair)
IMPORTANT
Never handle the pyrotechnic systems (pretension-
ers or airbags) near to a source of heat or naked
flame - they may be triggered.
143958
REMOVAL
a Remove the elastic securing straps (1) from the
seatback cover.
I - REMOVAL PREPARATION OPERATION
a Remove:
77A-1
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting 77A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REMOVAL OPERATION
143960
143959
a Remove:
- the elastic retaining strap (2) on the seatback cov-
er,
- the front retaining sections (3) of the front seat
base cover,
- the side retaining sections (4) of the front seat base
cover,
- the "cover - foam" assembly of the front seat base.
143961
a Cut the clips on the seat trim (5) .
a Remove the front seat base cover.
77A-2
FRONT SEAT TRIM
Front seat base trim: Removal - Refitting 77A
EXPORT EQUIPMENT LEVEL ADDITIONAL
REFITTING
Note:
To avoid any risk of damaging the seat trims and
mechanisms, remove any metal residues of the
seat trim clips.
II - REFITTING OPERATION
a Refit:
- the front seat base cover,
- the new seat trim clips using the tool (Car. 1521) on
the centre section,
- the clips of the seat trim using the tool (Car. 1521)
on the side sections.
a Refit the "cover - foam" assembly of the front seat
base.
a Proceed in the reverse order to removal.
77A-3
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 06 or CLOTH 07, and EXPORT EQUIPMENT LEVEL ADDITIONAL
IMPORTANT
To avoid a fault with or even triggering of pyrotech- II - REMOVAL OPERATION
nic components (airbags or pretensioners), check
the airbag computer using the diagnostic tool.
IMPORTANT
Never handle the pyrotechnic systems (pretension-
ers or airbags) near to a source of heat or naked
flame - they may be triggered.
REMOVAL
77A-4
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 06 or CLOTH 07, and EXPORT EQUIPMENT LEVEL ADDITIONAL
144150
a Unclip the lower retaining section (2) of the front
seatback cover.
77A-5
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 06 or CLOTH 07, and EXPORT EQUIPMENT LEVEL ADDITIONAL
144151 144153
144152 144154
a Gradually cut the clips on the seat trim (3) .
WARNING
To avoid any risk of damaging the foam, separate
the cover from the foam by holding the velcro
strips.
77A-6
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 06 or CLOTH 07, and EXPORT EQUIPMENT LEVEL ADDITIONAL
Note:
To avoid any risk of damaging the seat trims and
mechanisms, remove any metal residues of the
seat trim clips.
141591
a Detach the retaining section of the front seat side
(chest-level) airbag concentrator at (5) by sliding it.
REFITTING
77A-7
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 03 or CLOTH 04 or CLOTH 05, and EXPORT EQUIPMENT LEVEL ADDITIONAL
IMPORTANT
To avoid a fault with or even triggering of pyrotech- II - OPERATION FOR REMOVAL OF PART
nic components (airbags or pretensioners), check CONCERNED
the airbag computer using the diagnostic tool.
IMPORTANT
Never handle the pyrotechnic systems (pretension-
ers or airbags) near to a source of heat or naked
flame - they may be triggered.
REMOVAL
I - REMOVAL OPERATION
77A-8
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 03 or CLOTH 04 or CLOTH 05, and EXPORT EQUIPMENT LEVEL ADDITIONAL
144150
a Unclip the lower retaining section (2) of the front
seatback cover.
77A-9
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 03 or CLOTH 04 or CLOTH 05, and EXPORT EQUIPMENT LEVEL ADDITIONAL
144277 144280
a Gradually cut the clips on the seat trim (3) .
WARNING
To avoid any risk of damaging the seat trims and
mechanisms, remove any metal residues of the
seat trim clips.
144279
77A-10
FRONT SEAT TRIM
Front seatback trim: Removal - Refitting 77A
CLOTH 03 or CLOTH 04 or CLOTH 05, and EXPORT EQUIPMENT LEVEL ADDITIONAL
a Remove the front seatback cover.
REFITTING
II - REFITTING OPERATION
a Proceed in the reverse order to removal.
a Crimp the new seat trim clips onto the lumbar pad
using the tool (Car. 1521).
144278
a Unlock the retaining section pin of the front seat
(chest-level) side airbag concentrator.
a Remove the retaining section pin (4) from the front
seat (chest-level) side airbag concentrator.
141591
a Detach the retaining section of the front seat side
(chest-level) airbag at (5) by sliding it.
77A-11
FRONT SEAT TRIM
Front seat lower casing: Removal - Refitting 77A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REMOVAL OPERATION
Equipment required
1 - Front seat base interior casing
Diagnostic tool
REMOVAL
138045
a Unclip the front seat base interior casing (2) .
137996
a Remove the elastic straps (1) from the front seat-
back cover.
143772
a
Note:
Replace the clip if deteriorated.
77A-12
FRONT SEAT TRIM
Front seat lower casing: Removal - Refitting 77A
EXPORT EQUIPMENT LEVEL ADDITIONAL
2 - Front seat base exterior casing - the front seat height adjustment control (see 75A,
Front seat frames and mechanisms, Front seat
height adjuster control: Removal - Refitting,
FRONT SEAT TYPE 02 or FRONT SEAT TYPE 04 page 75A-6) .
or FRONT SEAT TYPE 05 or FRONT SEAT TYPE
06 a Unclip the front seat base exterior casing.
143775
138048
a Disconnect the connector (5) from the front seat
heated pad.
a Unclip the clip from the wiring of the front seat heat-
ed pad (6) .
REFITTING
REFITTING OPERATION
a Proceed in the reverse order to removal.
a Carry out a function test.
143774
a Remove:
- the bolts (3) and (4) from the front seat base exteri-
or casing,
- the front seatback angle control (see 75A, Front
seat frames and mechanisms, Front seat back-
rest tilt control: Removal - Refitting, page 75A-
12) ,
77A-13
REAR SEAT TRIM
1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
Tightening torquesm
REMOVAL
142782
a Unclip the trims from the unlocking control of the
rear bench seatback using the tool (Car. 1363).
78A-1
REAR SEAT TRIM
1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
1 - 2/3 rear bench seatback cover 2 - 1/3 rear bench seatback cover
137422 142808
a Remove: a Remove:
142785
a Remove:
- the bolts (2) ,
- the 2/3 rear bench seat supports.
78A-2
REAR SEAT TRIM
1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REMOVAL OPERATION
142788
144187
a Extract the zip fasteners (4) .
a Open the zip fasteners.
a Remove clip (5) .
142789
a Lift up the foam of the 2/3 rear bench seatback.
a Unclip the clip (6) .
a Remove:
- the 2/3 rear bench seat headrest guides (see 79A,
Seat accessories, Rear bench seat headrest
guide: Removal - Refitting, page 79A-8) ,
- the "cover - foam" assembly of the 2/3 rear bench
seatback.
78A-3
REAR SEAT TRIM
1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
2 - 1/3 rear bench seatback cover
142787
a Separate the cover from the 2/3 rear bench seat- 137424
back foam. a Extract the zip fasteners (7) .
a Remove the cover of the 2/3 rear bench seatback. a Open the zip fasteners.
a Remove:
WARNING - the clip (8) ,
To avoid any risk of damaging the foam, separate
- the rear bench seat headrest guides (see 79A,
the cover from the foam by holding the velcro
Seat accessories, Rear bench seat headrest
strips.
guide: Removal - Refitting, page 79A-8) ,
- the "cover - foam" assembly of the 1/3 rear bench
seatback.
78A-4
REAR SEAT TRIM
1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
REFITTING
142786
a Separate the cover from the 1/3 rear bench seat-
back foam.
a Remove the cover of the 1/3 rear bench seatback. 142781
WARNING
To avoid any risk of damaging the foam, separate
the cover from the foam by holding the velcro
strips.
142779
WARNING
To avoid any risk of the cover detaching or any
folds in the cover, check that the velcro strips are
secure on the foam. If the velcro strip tears,
replace the foam.
78A-5
REAR SEAT TRIM
1/3 and 2/3 rear bench seatback trim: Removal - Refitting 78A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
1/3 rear bench seatback cover
a Refit:
a Position the cover of the rear bench seatback on the - the trim of the rear centre seat belt strap guide,
foam, starting with the side velcro strips.
- the bolt (1) .
Note:
2 - 1/3 rear bench seatback cover
The markings on the foam are a guide for posi-
tioning the velcro strips. a Refit:
a Clip on the clip (6) . - the rear bench seatbacks (see 76A, Rear seat
frames and mechanisms, Rear bench seatback:
a Refit the clips (5) . Removal - Refitting, page 76A-1) ,
a Close the zip fasteners using the tool (Car. 1558). - the rear bench seat bases (see 76A, Rear seat
frames and mechanisms, Rear bench seat
a Fit the zip fasteners (4) . base: Removal - Refitting, page 76A-4) .
78A-6
REAR SEAT TRIM
Rear bench seat base trim: Removal - Refitting 78A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - REMOVAL OPERATION
Special tooling required
REMOVAL
144382
2/3 seat
144383
a Cut the clips (1) .
a Remove:
- the cover retaining sections (2) ,
- the « cover - foam » assembly of the rear bench
seat base.
78A-7
REAR SEAT TRIM
Rear bench seat base trim: Removal - Refitting 78A
EXPORT EQUIPMENT LEVEL ADDITIONAL
Incorrect
137412 142781
a Separate the cover from the rear bench seat base
foam. Correct
WARNING
To avoid any risk of damaging the foam, separate
the cover from the foam by holding the velcro
strips.
REFITTING
142779
a Check that the velcro strips are properly fastened on
the foam.
WARNING
To avoid any risk of the cover detaching or any
folds in the cover, check that the velcro strips are
secure on the foam. If the velcro strip tears,
replace the foam.
78A-8
REAR SEAT TRIM
Rear bench seat base trim: Removal - Refitting 78A
EXPORT EQUIPMENT LEVEL ADDITIONAL
142780
Note:
The markings on the foam are a guide for posi-
tioning the velcro strips.
a Align the ends of the velcro strips with the marks (4) .
II - REFITTING OPERATION
a Refit the cover (3) of the rear bench seat base on the
foam.
a Refit:
a Refit the rear bench seat base (see 76A, Rear seat
frames and mechanisms, Rear bench seat base:
Removal - Refitting, page 76A-4) .
78A-9
SEAT ACCESSORIES
Front headrest: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
Note:
The front seat headrest has an integrated con-
trol.
139290
139291
a Press the unlocking button on each headrest guide.
Note:
Depending on the type of unlocking button, this
operation is performed manually or using a flat-
blade screwdriver.
79A-1
SEAT ACCESSORIES
Front headrest: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
139292
a Remove the front seat headrest.
79A-2
SEAT ACCESSORIES
Front headrest: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
REFITTING
REFITTING OPERATION FOR PART CONCERNED a Insert the rods of the front seat headrest in the head-
rest guides.
a Push the front seat headrest until it locks into place
FRONT HEADRESTS 0 or FRONT HEADRESTS 0
with the locking notches then adjust the front seat
headrest to the low position.
Unaligned headrest rods
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
142683
142684
IMPORTANT
To avoid any risk of incorrectly positioning the
rods of the front seat headrest, align the rods
before inserting them in the headrest guides.
79A-3
SEAT ACCESSORIES
Front seat headrest guide: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
Note:
The headrest guides can be removed without
removing the front seatback cover.
79A-4
SEAT ACCESSORIES
Front seat headrest guide: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - OPERATION FOR REMOVAL OF PART
CONCERNED
Note:
The locking clips of the front seat headrest
guides are all on the same side.
REFITTING
Note:
To prevent the headrest guides from being mixed
up, each headrest guide has a specific indexing
device.
II - FINAL OPERATION
a Refit the front seat headrest (see 79A, Seat acces-
sories, Front headrest: Removal - Refitting, page
79A-1) .
a Carry out a function test.
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
141582
a Slightly detach the "foam - cover" assembly of the
seatback near the headrest guides to reveal the
locking clips of the front seat headrest guides.
a Unclip the front seat headrest guides by pressing the
locking clips using a flat-blade screwdriver.
a Remove the front seat headrest guides.
79A-5
SEAT ACCESSORIES
Front armrest: Removal - Refitting 79A
FRONT ARMREST, and EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL
II - REMOVAL OPERATION
144144
a Remove:
- the front armrest mounting bolts (1) ,
- the front armrest.
REFITTING
a Proceed in the reverse order to removal.
79A-6
SEAT ACCESSORIES
Rear centre armrest: Removal - Refitting 79A
1-2/3 REAR BENCH SEAT + ARMREST + N/R SEATBACK, and EXPORT EQUIPMENT LEVEL ADDITIONAL
REMOVAL REFITTING
II - FINAL OPERATION
a Position the 1/3 rear bench seat (1) .
134165
134166
a Remove:
79A-7
SEAT ACCESSORIES
Rear bench seat headrest guide: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
137431
141490
REFITTING
I - REFITTING OPERATION
a Refit the rear bench seat headrest guides fully into
the rear seat frame.
a Check that the rear bench seat headrest guides are
secure on the rear seat frame.
79A-8
SEAT ACCESSORIES
Rear bench seat headrest guide: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
II - FINAL OPERATION
IMPORTANT
To prevent the headrest coming away from the
guide during a collision, check that headrest
guide locking system is functioning correctly.
79A-9
SEAT ACCESSORIES
Rear bench seat headrest: Removal - Refitting 79A
EXPORT EQUIPMENT LEVEL ADDITIONAL
a
Note: IMPORTANT
To prevent the headrest coming away from the
Depending on the type of unlocking button, this
guide during a collision, check that headrest
operation is performed manually or using a flat-
guide locking system is functioning correctly.
blade screwdriver.
REMOVAL
137420
REFITTING
79A-10