Professional Documents
Culture Documents
SKMVH Katalog (Eng)
SKMVH Katalog (Eng)
SKMV-H
MULTISTAGE PUMPS
Handled Liquids
Clean or slightly contaminated low viscosity liquids without
solid & fibrous particles.
Technical Data
Discharge Flange DN 32....DN 150 mm
Head up to 450 m
(Pmax: Suction Pressure + Shut off Head) •Pump and motor shafts are connected to each other with flexible
(*) The Material of pumps differ according to the type of pumped coupling.
liquid, operating temperature and pressure. Contact for detailed
information. •All impellers are balanced dynamically or statically according
to ISO 1940 class 6.3.
Design Features
•Axial thrust is balanced by impeller balancing holes system.
•Vertical ring section, multistage, centrifugal pumps with
closed impellers and diffusers. •Direction of rotation is always counter clockwise viewed
from drive end.
•8 models from DN 32 up to DN 150 discharge flange diameter.
•Bearings of SKMV-H type pumps are grease lubricated. Journal
•Suction nozzle flanges conform to EN 1092 - 2 / PN 16 and bearings used in the suction side is lubricated by the pumping
discharge nozzle flanges conform to EN 1092 - 2 / PN 40 (PN 63) liquid.
(For steel or stainless steel casing pumps, flanges comform to
related pressure class ratings defined in EN 1092 - 1)
Shaft Sealing
•SKMV-H pumps are short coupled with electric motors of •Depending on request or requirment, pumps with soft
IEC frame sizes with high efficiency class. packing or mechanical seals can be supplied.
Pump Designation
SKMV-H 100 / 6
Pump Type
Discharge Nozzle (DN-mm)
Number of Stage
101
Field Chart SKMV-H
1450 rpm
300
200 125/
7 150
/5
100
/9 125/
100 6 150
/8 /4
80/
11 100 125/
80/ /7 5
65/ 10
11
65/ 80/ 100 150
10 9 /6 125/ /3
50/ 4
12 65/ 80/
100 40/ 50/ 9 8 100
13 11 /5
90 40/1 50/
10
65/
8 80/
7
32/ 2
80 32/ 4
1 40/1
1
50/
9 65/ 100 125/
13 40/ 7 80/ /4 3
50/ 6 150
70 32/
12 40/
10 8 /2
32/1 9 65/
1 6 80/
60 50/
Head (m)
32/ 40/ 7 5
10 8 100
65/ /3
32/ 50/ 5
50 9 40/ 6
7 80/
32/ 4 125/
8 40/ 2
6 50/ 65/
5 4
40 32/
7
80/
32/ 40/ 3 100
6 5 50/ /2
4
30 32/ 65/
5 40/ 3
4
50/
32 / 3
4
20 40/
3 65/ 80/
2 2
16 50/
2
32/ 40/
3 2
10
4 5 6 7 8 9 10 20 30 40 50 60 70 80 100 200 300 400 500
Capacity (m³/h)
2900 rpm
500
50/10
400
40/12 50/9
40/11
32/13 50/8 65/7
40/10
300 32/12
32/11 40/9 50/7
65/6
32/10 40/8 50/6
32/9 65/5
40/7
200 32/8 50/5 80/4
32/7 40/6 65/4
40/5 50/4
32/6
80/3
90 32/4 40/3
80
80/2
70 65/2
32/3
50/2
60
50 40/2
40 32/2
30
20
6 7 8 9 10 20 30 40 50 60 100 200
Capacity (m³/h)
102
Secitonal Drawings SKMV-H
Part List
004 Suction Casing
005 Discharge Casing
006 Stage Casing
011 Pump Foot
012 Motor Pedestal
087 600
015 Diffuser
016 Last Stage Diffuser
012
*020 Wear Ring (diffuser)
393 *021 Wear Ring (stage casing)
211
*022 Wear Ring (suction casing)
394 030 Bearing Housing
035 Bearing Cover
035 036 Sleeve Bearing
037 Sleeve Bearing Cover
201 042 Gland
421 044 Lantern Ring
069
042 *048 Mechanical Seal Cover
088 050 Impeller
071 060 Pump Shaft
068 Shaft Sleeve (sleeve bearing)
030
069 Spacer Sleeve (bearing)
213 070 Shaft Sleeve (suction casing)
168 071 Shaft Protecting Sleeve (soft packing)
*074 Shaft Protecting Sleeve (mechanical seal)
060 087 Flexible Coupling
005
423 088 Thrower
400 090 Tiebolt
016 095 Sleeve Bearing Flushing Pipe
044 168 Split Ring
420
*021 201 Double Row Ball Bearing
006 210 Key (impeller)
210 015 211 Key (coupling)
213 Key (shaft protecting sleeve)
050 095
214 Key (sleeve bearing)
*020 090 391 Shaft End Nut
*022 392 Lock Washer
393 Shaft End Nut
070 Lock Washer
394
400 Soft Packing
*405 Mechanical Seal
004 011 420 O-Ring
421 O-Ring
422 O-Ring
423 O-Ring
422 036 392 214 391 068 037 *424 O-Ring
600 Electric Motor
(*) Optional
Mechanical Seal Application
*048
*405
*424
*074
103
Technical Data SKMV-H
Y View
Y
K1
s
KxK
B
Bearing Type L
Pump Bearing
Type Type
32 3305
40 3305 C
50 3306
65 3307
80 3308
100 3309
125 3310
150 3312 A
Pump l
Type d l t u
32 22 50 25 6
40 22 50 25 6
50 28 65 31 8
65 32 65 35 10 d
u
80 38 80 41 10
100 42 110 45 12
125 48 110 51,5 14
t
150 55 110 59 16
Flange Dimensions
EN 1092 - 2
Suction & Discharge (PN 16) Suction & Discharge (PN 40)
DNe/DNb
Df k s n Df k s n
s
32 140 100 19 4 140 100 19 4
40 150 110 19 4 150 110 19 4
50 165 125 19 4 165 125 19 4
65 185 145 19 4 185 145 19 8
DNe/DNb
104
Technical Data SKMV-H
1450 rpm
Pump Motor Dimensions (mm) C (mm)
Type No Number of Stages
IEC DNe DNb L A B e KxK K1 s 1 2 3 4 5 6 7 8 9 10 11 12 13 14
32 80 40 32 399+C 105 298 155 212 300 18 71 114 157 200 243 286 329 372 415 458 501 544 587 630
32 90 40 32 399+C 105 298 155 212 300 18 71 114 157 200 243 286 329 372 415 458 501 544 587 630
32 100 40 32 409+C 105 308 155 212 300 18 71 114 157 200 243 286 329 372 415 458 501 544 587 630
40 90 50 40 405+C 103 302 175 212 300 18 78 133 188 243 298 353 408 463 518 573 628 683 738 -
40 100 50 40 415+C 103 312 175 212 300 18 78 133 188 243 298 353 408 463 518 573 628 683 738 -
40 112 50 40 415+C 103 312 175 212 300 18 78 133 188 243 298 353 408 463 518 573 628 683 738 -
40 132 50 40 435+C 103 332 175 212 300 18 78 133 188 243 298 353 408 463 518 573 628 683 738 -
50 100 65 50 453+C 114 340 190 247 350 18 90 152 214 276 338 400 462 524 586 648 710 772 - -
50 112 65 50 453+C 114 340 190 247 350 18 90 152 214 276 338 400 462 524 586 648 710 772 - -
50 132 65 50 473+C 114 360 190 247 350 18 90 152 214 276 338 400 462 524 586 648 710 772 - -
50 160 65 50 503+C 114 390 190 247 350 18 90 152 214 276 338 400 462 524 586 648 710 772 - -
65 100 80 65 505+C 135 368 215 247 350 18 107 178 249 320 391 462 533 604 675 746 817 - - -
65 112 80 65 505+C 135 368 215 247 350 18 107 178 249 320 391 462 533 604 675 746 817 - - -
65 132 80 65 525+C 135 388 215 247 350 18 107 178 249 320 391 462 533 604 675 746 817 - - -
65 160 80 65 555+C 135 420 215 247 350 18 107 178 249 320 391 462 533 604 675 746 817 - - -
65 180 80 65 555+C 135 420 215 247 350 18 107 178 249 320 391 462 533 604 675 746 817 - - -
80 132 100 80 568+C 145 423 265 247 350 23 112 195 278 361 444 527 610 693 776 859 942 - - -
80 160 100 80 598+C 145 453 265 247 350 23 112 195 278 361 444 527 610 693 776 859 942 - - -
80 180 100 80 598+C 145 453 265 247 350 23 112 195 278 361 444 527 610 693 776 859 942 - - -
80 200 100 80 598+C 145 453 265 247 350 23 112 195 278 361 444 527 610 693 776 859 942 - - -
80 225 100 80 628+C 145 483 265 247 350 23 112 195 278 361 444 527 610 693 776 859 942 - - -
100 160 125 100 675+C 170 504 300 318 450 23 133 233 333 433 533 633 733 833 933 - - - - -
100 180 125 100 675+C 170 504 300 318 450 23 133 233 333 433 533 633 733 833 933 - - - - -
100 200 125 100 675+C 170 504 300 318 450 23 133 233 333 433 533 633 733 833 933 - - - - -
100 225 125 100 705+C 170 534 300 318 450 23 133 233 333 433 533 633 733 833 933 - - - - -
100 250 125 100 705+C 170 534 300 318 450 23 133 233 333 433 533 633 733 833 933 - - - - -
100 280 125 100 705+C 170 534 300 318 450 23 133 233 333 433 533 633 733 833 933 - - - - -
125 200 150 125 717+C 178 538 375 424 600 27 165 280 395 510 625 740 855 - - - - - - -
125 225 150 125 747+C 178 568 375 424 600 27 165 280 395 510 625 740 855 - - - - - - -
125 250 150 125 747+C 178 568 375 424 600 27 165 280 395 510 625 740 855 - - - - - - -
125 280 150 125 747+C 178 568 375 424 600 27 165 280 395 510 625 740 855 - - - - - - -
125 315 150 125 777+C 178 598 375 424 600 27 165 280 395 510 625 740 855 - - - - - - -
150 250 200 150 888+C 265 623 425 424 600 27 218 363 508 653 798 - - - - - - - - -
150 280 200 150 888+C 265 623 425 424 600 27 218 363 508 653 798 - - - - - - - - -
150 315 200 150 918+C 265 653 425 424 600 27 218 363 508 653 798 - - - - - - - - -
2900 rpm
105
Technical Data SKMV-H
1.4021+QT
2.0975.01
Tungsten
2.1050.01
2.1096.01
Carbide
0.7040
0.6025
0.7043
1.4008
1.4408
1.4404
1.4409
1.4460
1.4500
1.0503
1.4308
1.4469
1.4309
1.4462
PART LIST
1.0619
1.4301
1.4021
1.4517
1.4317
Suction Casing
Discharge Casing
Stage Casing
Diffuser
Impeller
Shaft
Bearing Housing
Wear Ring (Casing)
Shaft Sleeve
Shaft Pro. Sleeve
Spacer Sleeve
Sleeve Bearing
Mechanical Seal (*) EN 12756
(*) Optional :Depending on customer requirement or request different types and brands of mechanical seals are applicable. Standard manufacturing
Optional
Material Equivalents
Flange Positions
Explanation :
L3/9
Discharge Flange Position (D)
Suction Flange Position (S)
Direction of Rotation (L)
Direction of rotation viewed from drive end
L : Left
Attention : In the absence of specific request, pumps are supplied with the
following nozzle arrangement:
. L 3/9 : up to 2 stages
L 3/3 L 3/6 L 3/9 L 3/0 . L 3/3 : 3 or more stages
106