Professional Documents
Culture Documents
32-41-11-000-006-A - Removal of The MLG Wheel
32-41-11-000-006-A - Removal of The MLG Wheel
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LAN
DING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GE
AR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAF
T AND/OR EQUIPMENT.
WARNING: IT IS RECOMMENDED TO ONLY REMOVE ONE WHEEL AND TIRE ASSEMBLY FRO
M THE LANDING GEAR AT THE SAME TIME. IF YOU REMOVE THE TWO WHEEL A
ND TIRE ASSEMBLIES AT THE SAME TIME, DAMAGE TO THE AIRCRAFT AND INJ
URY TO PERSONS CAN OCCUR.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL
MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
QT
REFERENCE DESIGNATION
Y
No specific 1 ADAPTER - TIRE INFLATION/DEFLATION
No specific AR SAFETY CLIP - CIRCUIT BREAKER
No specific AR TROLLEY - WHEEL CHANGE, A/C
No specific AR WARNING NOTICE(S)
REFERENCE DESIGNATION
03GBB1 Synthetic Oil base Grease-General Purpose Clay Thickene
d-
03GCB1 Synthetic Oil base Grease-Landing Gear Wheel Bearing Lit
hium Thickened -
D. Referenced Information
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
REFERENCE DESIGNATION
Ref. 07-11-00-581-001-A Lifting for Aircraft Maintenance Operations
Ref. 07-12-00-582-002-A Jacking of the Main Landing Gear
Ref. 29-10-00-863-002-A Pressurize the Yellow Hydraulic System with a Hydraulic
Ground Power-Cart
Ref. 29-24-00-863-001-A Pressurize the Yellow Hydraulic System with the Electric P
ump
Ref. 32-00-00-481-001-A Installation of the Safety Devices on the Landing Gears
Ref. 32-41-00-210-003-A Functional Check of Tire Pressures
SUBTASK 32-41-11-210-074-A
B. Wheel Assembly Check
Ref. Fig. MLG Wheel
WARNING: BEFORE YOU LOOSEN THE AXLE NUT, DEFLATE THE TIRES ON THE
WHEEL ASSEMBLIES WITH MISSING, BROKEN OR LOOSE TIE-BOLT
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
SUBTASK 32-41-11-865-113-A
C. Open, safety and tag this(these) circuit breaker(s):
WARNING: MAKE SURE THAT THE AIRCRAFT IS STABLE AND DOES NOT MOVE
DURING THE JACKING OPERATIONS.
IF THERE IS UNWANTED MOVEMENT OF THE AIRCRAFT, THE LANDI
NG-GEAR JACKING DOME CAN COME OFF THE JACK HEAD AND INJU
RY AND/OR DAMAGE CAN OCCUR.
(2) Do one of the steps that follow:
If you want to remove the MLG wheel from one of the two MLGs (LH or RH),
(a) lift the applicable MLG axle Ref. AMM TASK 07-12-00-582-002.
- Make sure that you do not lift the two MLG axles at the same time.
- Make sure that you do not remove more than one MLG wheel at the s
ame time.
If you want to remove the MLG wheel(s) from the two MLGs (LH and RH), lif
(b) t the aircraft on jacks Ref. AMM TASK 07-11-00-581-001.
(3) Put the PARK BRK control switch to the ON position.
On panel 400VU, make sure that the brake pressure indication on the Yellow
(a) brake-pressure triple indicator is correct.
If necessary, pressurize the brake accumulator with the Yellow hydraulic sys
tem Ref. AMM TASK 29-10-00-863-002 or Ref. AMM TASK 29-24-00-863-00
(b) 1.
NOTE: It is not necessary to do this step, if you have removed the MLG
© AIRBUS S.A.S. ALL RIGHTS RESERVED. CONFIDENTIAL AND PROPRIETARY DOCUMENT.
about:blank 4/13
9/19/22, 12:25 PM IGO - A318 / A319 / A320 / A321 - AMM - 01-Aug-2022 - 32-41-11-000-006-A - Removal of the MLG Wheel
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
wheel(s) from the two MLGs (LH and RH) and the aircraft is on jac
ks.
NOTE: If you must remove the wheel for access or inspections, it is not necessar
y to deflate the tire if:
- The tire is in the correct condition.
- The tire pressure is in the normal operating range Ref. AMM TASK
32-41-00-210-003.
If you do not find these two conditions, it is necessary to decrease t
he tire pressure.
(a) Remove the cap (51) from the inflation valve (50).
Decrease the tire pressure until the pressure gage of the ADAPTER - TIRE I
NFLATION/DEFLATION shows between 1.79 bar (26 psi) and 2.20 bar (32 p
(c) si).
(e) Put the cap (51) on the inflation valve (50) and tighten it.
4. Procedure
** ON A/C FSN 021-021, 026-026, 034-034, 049-052, 055-055, 058-058, 060-06
0, 062-062, 064-064, 069-074, 076-100, 112-150, 222-226, 231-233, 235-235, 2
37-238, 242-242, 244-250, 377-603, 651-651, 653-653
Ref. Fig. Main Gear Wheel
** ON A/C FSN 151-200, 240-240, 243-243
Ref. Fig. Main Gear Wheel
** ON A/C FSN 229-229, 301-376
NOTE: Remove the hubcap along the centerline of the wheel axle to prevent da
mage to the tachometer drive shaft.
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
(a) Make sure that the locating pin (12) is installed on the hubcap (11).
** ON A/C FSN 021-021, 026-026, 034-034, 049-052, 055-055, 058-058, 060-06
0, 062-062, 064-064, 069-074, 076-100, 112-150, 222-226, 229-229, 231-233, 2
35-235, 237-238, 242-242, 244-250, 301-603, 651-651, 653-653
NOTE: It is not necessary to remove the motor assembly of the brake fan as des
cribed in the AMM task 324851_000_005, to remove the wheel.
** ON A/C FSN 240-240, 243-243
SUBTASK 32-41-11-020-088-A
B. Removal of the Wheel
(a) Prepare a tag and attach it to the wheel and tire assembly.
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
(b) Write on the tag the reason for removal of the tire.
** ON A/C FSN 151-200
SUBTASK 32-41-11-020-088-B
B. Removal of the Wheel
(a) Prepare a tag and attach it to the wheel and tire assembly.
(b) Write on the tag the reason for removal of the tire.
** ON A/C FSN 401-499, 651-651, 653-653
SUBTASK 32-41-11-020-088-C
B. Removal of the Wheel
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
(a) Prepare a tag and attach it to the wheel and tire assembly.
(b) Write on the tag the reason for removal of the tire.
** ON A/C FSN 021-021, 026-026, 034-034, 049-052, 055-055, 058-058, 060-06
0, 062-062, 064-064, 069-074, 076-100, 112-150, 222-226, 229-229, 231-233, 2
35-235, 237-238, 242-242, 244-250, 301-400, 500-603
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
- NOT USED.
- NOT FULLY ENGAGED ON THE AXLE.
(1) Remove and discard the cotter pins (5) and nuts (4).
(2) Remove the washers (6) and the bolts (8).
(3) Remove the axle nut (7) with the ADAPTOR-MLG (H47682).
(4) Install the PROTECTOR (F46754-1000).
Apply a thin layer of Synthetic Oil base Grease-General Purpose Clay Thickened -
(Material Ref. 03GBB1) or Synthetic Oil base Grease-Landing Gear Wheel Bearing
(5) Lithium Thickened - (Material Ref. 03GCB1) on the axle protector.
(6) Put a TROLLEY - WHEEL CHANGE, A/C below the wheel assembly (1).
(7) Remove the wheel assembly (1).
(8) Record the reason for removal of the wheel.
(a) Prepare a tag and attach it to the wheel and tire assembly.
(b) Write on the tag the reason for removal of the tire.
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
C
B 2651GM
Z731
Z741
2649GM
C
A
2652GM
2650GM
50
51
C
B
52 x18
C
TYPICAL
N_MM_324111_4_VAL0_01_01
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
Z731 (Z741)
2651GM
A (2650GM)
2649GM
(2652GM)
1
2
10
4 x2
9
5 x2
6 x2
7
8 x2
A
TYPICAL
N_MM_324111_4_UBT0_01_05
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
2650GM
2649GM
A A
A A A
EXAMPLE
1
2652GM 2651GM
4
7
6
5
8
8 4
14
5
13
11 10
12
N_MM_324111_4_NAM0_01_03
REVISION REVISION
CUSTOMIZATION AIRCRAFT TYPES DOCTYPES TITLE
DATE NUMBER
A318 A319 A321 32-41-11-000-006-A - Removal of the
IGO AMM 01-Aug-2022 67
A320 MLG Wheel
TAIL NUMBER - MSN - FSN:
Print date: 2022-09-19 08:55:15
Z731 (Z741)
A 2649GM 1 2
(2650GM) 3
B 2651GM
(2652GM)
4 x2
5 x2
6 x2
9
10
8 x2
A B
TYPICAL
N_MM_324111_4_UBF0_01_04