GENUINE RUNNING BOARDS
FITTING INSTRUCTIONS
MODEL: TERRITORY
ACCESSORIES PART NUMBER: SX16450AA
Please read fitting instructions carefully and completely before attempting to fit the new
Running boards.
WARNING
1. Do not ail, cut weld or otherwise modify the side step.
2. If you are using electric welding on a motor vehicle, always check that the vehicle is not equipped
with electronic engine or instrument management equipment. Failure to do so could destroy any
onboard computers. Ifin doubt, check with the vehicle's manufacturer.
Equipment required
3/8" 90° drill Centre punch
mm rivet nut installation tool Corrosion inhibiting pair.
De-burring tool Holo saw or dril O16
Samm dri bit ‘16mm socket.
1mm reduced shank drill bit 13mm tube socket.
8.5mm dil bit 419mm socket.
Ruler or measuring tape. vadiive ratchet
Hammer.
Har
seription Gly [Torque Nim] Description Giy_[ Torque Nm
‘Aluminium stop assembly | 2 Foeward bracket agnihand [1 j
1M Fivet nut 1a Forward bracket ft hand — [1
[1M sering washer 16 Roar bracket 2 =
M0 tapi 2 aaa Centre bxgeket 2
‘Me Wizz Not 6 peur “Template rent AA +
Max 30 bot 14 [217 “Template font LH i
‘Spacor woe OTS xi.6x3 [2 “Template rear LH t
Loose plate T9x19x309 | 6 “Template rear FH 7
Loose plate 2328x309 | 10 ‘Template contre LH i
1M Nut 2 [any “Template contre RH t
([Bon, plate & wre 2
a 9c
Sn See BOSE PATE
never ar PAE, \Cugepscers,
Weer stess
\, AEE Ee
one
“Terory Funning Board Fiting Insuuctons 31/1208 Page 1 of6GENUINE
ACCESSORIES
RUNNING BOARDS
FITTING INSTRUCTIONS
MODEL: TERRITORY
PART NUMBER: SX16450AA
Please read fitting instructions carefully and completely before attempting to fit the new
Running boards.
Left hand side.
Stites “Cc
2/ Attach templates to inner face of vehicle sill, aligning them to the grommet sheetmetal holes.
—oruLnes.
x
2ay Rear Bracket template
Terntory Running Board Fiting Instructions 31/1204
Centro punch points indicated on template.
Pilot drill all centre points @3
Drill all @3 hole to 11.5 with the exception of the
rearmost horizontal mounting. Drill o 28.5.
Page 206GENUINE RUNNING BOARDS
FITTING INSTRUCTIONS
MODEL: TERRITORY
ACCESSORIES PART NUMBER: SX16450AA
Please read fitting instructions carefully and completely before attempting to fit the new
Running boards.
2by Centre Bracket template Centre punch points indicated on template,
Pilot drill all centre points 03
Drill 03 holes to 11.5,
2c! Forward Bracket template Centre punch points indicated on template,
Pilot dil ll centre points @3
Drill 3 holes to 011.5,
31 Coat exposed metal with a suitable corrosion inhibiter.
4) Install rivet nuts and brackets
Terrtory Purning Board Fiting instructions 811208 Page 3 016GENUINE RUNNING BOARDS
FITTING INSTRUCTIONS
ACCESSORIES PART NUMBER: SX16450AA
Please read fitting instructions carefully and completely before attempting to fit the new
Running boards.
4A/ Roar bracket.
<—Foeaypxsomcur stare awe 4A 1/Feed bold wite & plate through rear
\ Bris aaa most gland hole and @8.5 hole in body
\ thon into bracket fiting loose plate23 x 3
x 28 G9 hole MB spring washer and nut
loosely. as per diagram
21 Fit MB x 30 1.5P bok, spring washer
and loose plate 19 x 19 x 3 99 hole
through lower opening in bracket and into
fited rivet nu, loosely
3/ Square bracket to vehicte sil
4/ Using bracket as a guide mark inner
‘most mounting point, centre punch, plot
dill t0 3 and dil to O11 5.
5/ Coat exposed metal with a suitable
corrosion inhibiter.
6/ Move bracket to side and install rivet
rut
7/ Relocate rear bracket and fit MB x 30,
1.5P bol, spring washer and loose plato
23 x 23 x3 29 hole, See diagram
i g900.s PATE aime
4B 1/ If vehicle is fited with a transter
case cover complete steps 4.1 & 4.2.
4.1/ Remove rear most M10 bolt from
transfer ease guard.
4.2! Enlarge existing hole in transter
case guard by driling 216 hole in to
allow spacer to fit,
21 Oifer centre’ bracket to rivet nuts
fitted into sl panel,
Fit M8 x 30 1.5P bot, spring washer
and loose plate 19 x 19 x 3 28 hole
through lower opening in bracket and into
sae fitted rivet nut, loosely.
Sacer ise 3/ Fit MB x 30 1.5P bol, spring washer
Stentor and loose plate 23 x 23 x 3.09 hole
NE eae through horizontal mounting point in
5 WER Toere bracket and int fited rivet nut, loosely.
teleernar 4) Fit 16 x1.5 x 3mm spacer betwoon
sub frame and bracket on inner most
mounting point
5/ Align inner end of bracket with
existing hole in body, fix in position with
M10 taptte bolt. Sce diagram.
Note: - If vehicle is not fitted with a transter case cover use M10 taptite bolt supplied in box.
Tetrtory Rurring Board Fiting Instructions 311204 Page 4 ol 8GENUINE RUNNING BOARDS
FITTING INSTRUCTIONS
MODEL: TERRITORY
ACCESSORIES PART NUMBER: SX16450AA
Please read fitting instructions carefully and completely before attempting to fit the new
Running boards.
4C/ Front bracket.
4C 1/Offer front bracket to rivet nuts
cance atest Medel sant
oh. 2/ Fit M& x 30 1.6P bolt, spring
~ washer and loose plate 19 x 18 x 3.09
hole through lower opening in bracket
and into fitted rivet nut, loosely.
3/ Fit MB x 30 1'5P boll, spring
washor and looso plato 23 x 23 x 3.29
hole through horizontal mounting point
in bracket and into titted rivet nut,
sears loosely.
tt att Heeenncnwers . 4/ Square bracket to vehicle sil
itr 5/ Using bracket 2s a guide mark
inner most mounting point, centre
Mexsoeors } punch, pilot drill to 23 and drill to
Geigxvancos nue C 211.5. Coat exposed metal with a
tiled suitable corrosion inhibiter,
6/ Move bracket to side and instal
rivet nut.
7/ Relocate rear bracket and fit M8 x
30 1.5P bolt, spring washer and loose
plate 23 x 23 x 3 BS hole
See diagram.
51 Fitting of step to Brackets.
“Temitory Funeing Board Fiting Instuctions 211208 Page 5 018GENUINE RUNNING BOARDS
FITTING INSTRUCTIONS
MODEL: TERRITORY
ACCESSORIES PART NUMBER: SX16450AA
Please read fitting instructions carefully and completely before attempting to fit the new
Running boards.
5) 1/ With all brackets fitted loosely, fit
aluminium step to brackets by engage
aluminium onto tip of brackets.
2, Align three M8 x 16 bolts into slot in
top face of brackets.
'5/ Centre step to vehicle
4 Fix into position with three MB whizz
ruts.
5/ Tighten all bolts to torque listing.
6! Refit grommats on inner face of
vehicle sill
71 Repeat steps for Right hand side of
vehicle.
Terrtory Running Bears Fiting instructions 31/1208 Page 6 of6