Professional Documents
Culture Documents
Eng 2
Eng 2
Eng 2
#104 -t2 -s1"A axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0"No" -
i1"Yes"
#34 -t1 -s1"X axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#35 -t1 -s1"Y axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#36 -t1 -s1"Z axis pulse equivalency" -s2"pulse/mm" -m2 -min=50.000 -max=99999.000
#37 -m0
#38 -t1 -s1"A axis pulse equivalency" -s2"" -m2 -min=50.000 -max=999999.000
#39 -t2 -s1"A axis pulse unit" -m2 -min=0.000 -max=1.000 -i0"pulse/deg" -
i1"pulse/circle"
#40 -t2 -s1"AB axis Selection" -m2 -min=0.000 -max=1.000 -i0"A axis" -i1"B axis"
#230=0 -t2 -s1"X-axis command type" -m0 -min=0.000 -max=1.000 -i0"PLU/DIR" -i1"A/B
phase"
#231=0 -t2 -s1"Y-axis command type" -m0 -min=0.000 -max=1.000 -i0"PLU/DIR" -i1"A/B
phase"
#232=0 -t2 -s1"Z-axis command type" -m0 -min=0.000 -max=1.000 -i0"PLU/DIR" -i1"A/B
phase"
#233=0 -t2 -s1"A-axis command type" -m0 -min=0.000 -max=1.000 -i0"PLU/DIR" -i1"A/B
phase"
#234 -t2 -s1"X-axis DIR in A/B phase mode" -m0 -min=0.000 -max=1.000 -i0"+" -i1"-"
#235 -t2 -s1"Y-axis DIR in A/B phase mode" -m0 -min=0.000 -max=1.000 -i0"+" -i1"-"
#236 -t2 -s1"Z-axis DIR in A/B phase mode" -m0 -min=0.000 -max=1.000 -i0"+" -i1"-"
#237 -t2 -s1"A-axis DIR in A/B phase mode" -m0 -min=0.000 -max=1.000 -i0"+" -i1"-"
#390 -t2 -s1"X axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#391 -t2 -s1"Y axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#392 -t2 -s1"Z axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#393 -t2 -s1"A axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#418 -t2 -s1"X axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low"
-i1"High"
#419 -t2 -s1"Y axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low"
-i1"High"
#420 -t2 -s1"Z axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low"
-i1"High"
#421 -t2 -s1"A axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0"Low"
-i1"High"
#416 -t0 -s1"Time interval between DIR & pulse" -s2"ns" -m2 -min=0.000 -
max=9999.000
#100 -t1 -s1"X axis manual control speed" -s2"mm/min" -m3 -min=99.000 -
max=99999.000
#101 -t1 -s1"Y axis manual control speed" -s2"mm/min" -m3 -min=99.000 -
max=99999.000
#102 -t1 -s1"Z axis manual control speed" -s2"mm/min" -m3 -min=99.000 -
max=99999.000
#103 -t1 -s1"A axis manual control speed" -s2"deg/min" -m3 -min=99.000 -
max=99999.000
#41 -t1 -s1"X Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -
max=99999.000
#42 -t1 -s1"Y Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -
max=99999.000
#43 -t1 -s1"Z Axis max speed in M_Ctrl mode" -s2"mm/min" -m3 -min=99.000 -
max=99999.000
#44 -t1 -s1"A Axis max speed in M_Ctrl mode" -s2"deg/min" -m3 -min=99.000 -
max=99999.000
#45 -t1 -s1"X axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=1.000 -
max=9999.000
#46 -t1 -s1"Y axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=1.000 -
max=9999.000
#47 -t1 -s1"Z axis start Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=1.000 -
max=9999.000
#48 -t1 -s1"A axis start Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=1.000 -
max=9999.000
#263 -t1 -s1"X axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -
max=9999.000
#264 -t1 -s1"Y axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -
max=9999.000
#265 -t1 -s1"Z axis stop Acc in M_Ctrl mode" -s2"mm/s2" -m3 -min=9.000 -
max=9999.000
#266 -t1 -s1"A axis stop Acc in M_Ctrl mode" -s2"deg/s2" -m3 -min=9.000 -
max=9999.000
#78 -t1 -s1"Z axis lifting protection speed" -s2"mm/min" -m4 -min=99.000 -
max=99999.000
#79 -t1 -s1"Z axis dropping protection speed" -m4 -min=99.000 -max=99999.000
#113 -t2 -s1"Arc interpolation algorithm selection" -s2"" -m4 -min=0.000 -max=1.000
-i0"Hard algorithm" -i1"Soft algorithm"
#123=0.001 -t1 -s1"Soft arc algorithm chord error" -s2"mm" -m0 -min=0.001 -max=0.1
#124 -t1 -s1"Circular centrifugal acceleration" -s2"mm/s2" -m4 -min=0.000 -
max=9999.000
#125 -t1 -s1"Circular speed adjustment factor" -s2"" -m4 -min=0.1 -max=2.0
#435 -t1 -s1"X axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
#436 -t1 -s1"Y axis protection speed" -s2"mm/min" -m4 -min=99.000 -max=99999.000
#82 -t1 -s1"Z axis safe height" -s2"mm" -m4 -min=0.000 -max=99.000
#89 -t1 -s1"Z axis back distance when pause" -s2"mm" -m4 -min=0.000 -max=99.000
#2031 -t2 -s1"Uniaxial acc is limited by M_Ctrl start acc" -m4 -min=0.000 -
max=1.000 -i0"No" -i1"Yes"
#2037 -t2 -s1"Is FRO valid for G0?" -m4 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#219 -t2 -s1"If Stop Spindle when pause" -m6 -min=0.000 -max=1.000 -i0"No" -i1"Yes"
#227 -t2 -s1"Spindle switch Active level" -m6 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#422 -t2 -s1"definition of PWM Electric level" -m6 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#433 -t0 -s1"PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000
#108 -t2 -s1 "M Bus IO command response" -s3"0:not response,1:response" -m7 -
min=0.000 -max=1.000 -i0"No" -i1"Yes"
#109 -t0 -s1 "M Bus IO default status" -m7 -min=0 -max=4294967295
#110 -t2 -s1 "M Bus IO Initialization strategy" -m7 -min=0.000 -max=1.000 -i0"mode
1" -i1"mode 2"
#228 -t2 -s1"M8/M9 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#229 -t2 -s1"M10/M11 active electric level" -m7 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#51 -t2 -s1"Enable limit signal when HOME" -s3"0:Disable,1:Enable" -m8 -min=0.000 -
max=1.000 -i0"Disable" -i1"Enable"
#52 -t2 -s1"Enable X Home Searching function" -s3"0:not enable,1:enable" -m8 -
min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#53 -t2 -s1"Enable Y Home Searching function" -s3"0:not enable,1:enable" -m8 -
min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#54 -t2 -s1"Enable Z Home Searching function" -s3"0:not enable,1:enable" -m8 -
min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#55 -t2 -s1"Enable A Home Searching function" -s3"0:not enable,1:enable" -m8 -
min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#60 -t2 -s1"X axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#61 -t2 -s1"Y axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#62 -t2 -s1"Z axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#63 -t2 -s1"A axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#64 -t2 -s1"X axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -
i1"Positive"
#65 -t2 -s1"Y axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -
i1"Positive"
#66 -t2 -s1"Z axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -
i1"Positive"
#67 -t2 -s1"A axis Home direction" -m8 -min=0.000 -max=1.000 -i0"Negative" -
i1"Positive"
#56 -t1 -s1"X axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#57 -t1 -s1"Y axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#58 -t1 -s1"Z axis Home speed" -s2"mm/min" -m8 -min=99.000 -max=99999.000
#59 -t1 -s1"A axis Home speed" -s2"deg/min" -m8 -min=99.000 -max=99999.000
#83 -t1 -s1"X axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
#84 -t1 -s1"Y axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
#85 -t1 -s1"Z axis back distance after Home" -s2"mm" -m8 -min=0.000 -max=99.000
#86 -t1 -s1"A axis back distance after Home" -s2"deg" -m8 -min=0.000 -max=360.000
#126 -t2 -s1"Home reminder after booting" -s2"" -m8 -min=0.000 -max=1.000 -i0"No" -
i1"Yes"
#116 -t2 -s1"X-axis zero signal source select" -s2"" -m8 -min=0.000 -max=2.000 -
i0"HOME signal" -i1"X++limit signal" -i2"X--limit signal"
#117 -t2 -s1"Y-axis zero signal source select" -s2"" -m8 -min=0.000 -max=2.000 -
i0"HOME signal" -i1"Y++limit signal" -i2"Y--limit signal"
#118 -t2 -s1"Z-axis zero signal source select" -s2"" -m8 -min=0.000 -max=2.000 -
i0"HOME signal" -i1"Z++limit signal" -i2"Z--limit signal"
#119 -t2 -s1"A-axis zero signal source select" -s2"" -m8 -min=0.000 -max=2.000 -
i0"HOME signal" -i1"A++limit signal" -i2"A--limit signal"
#2024 -t1 -s1"X axis Home offset" -s2"mm" -m8 -min=-999.000 -max=999.000
#2025 -t1 -s1"Y axis Home offset" -s2"mm" -m8 -min=-999.000 -max=999.000
#2026 -t1 -s1"Z axis Home offset" -s2"mm" -m8 -min=-999.000 -max=999.000
#2027 -t1 -s1"A axis Home offset" -s2"deg" -m8 -min=-999.000 -max=999.000
#68 -t2 -s1"Tool Setting function mode " -m9 -min=0.000 -max=3.000 -i0"Disable" -
i1"mode 1" -i2"mode 2" -i3"mode 3"
#70 -t2 -s1"Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#69 -t1 -s1"Thickness of tool sensor" -s2"mm" -m9 -min=-99.000 -max=99.000
#71 -t2 -s1"Initial tool's position" -m9 -min=0.000 -max=1.000 -i0"current
position" -i1"fixed position"
#2001 -t1 -s1"Tool plate thick for X" -s2"mm" -m9 -min=0.000 -max=999.000
#2002 -t1 -s1"Tool plate thick for Y" -s2"mm" -m9 -min=0.000 -max=999.000
#2003 -t1 -s1"Tool plate thick for Z" -s2"mm" -m9 -min=0.000 -max=999.000
#2004 -t1 -s1"shift of X axis before probed" -s2"mm" -m9 -min=-999.000 -max=999.000
#2005 -t1 -s1"shift of Y axis before probed" -s2"mm" -m9 -min=-999.000 -max=999.000
#2006 -t1 -s1"Z position before X(Y)-axis probed" -s2"mm" -m9 -min=-999.000 -
max=999.000
#2007 -t1 -s1"Back distance when the tool touches the X-axis edge" -s2"mm" -m9 -
min=0.000 -max=999.000
#2008 -t1 -s1"Back distance when the tool touches the Y-axis edge" -s2"mm" -m9 -
min=0.000 -max=999.000
#2009 -t1 -s1"Back distance when the tool touches the Z-axis edge" -s2"mm" -m9 -
min=0.000 -max=999.000
#408 -t2 -s1"Effective electric level of X--" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#409 -t2 -s1"Effective electric level of Y--" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#410 -t2 -s1"Effective electric level of Z--" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#411 -t2 -s1"Effective electric level of A--" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#412 -t2 -s1"Effective electric level of X++" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#413 -t2 -s1"Effective electric level of Y++" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#414 -t2 -s1"Effective electric level of Z++" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#415 -t2 -s1"Effective electric level of A++" -m10 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#2038 -t2 -s1"Enable software limit alarm in the idle state" -m11 -min=0.000 -
max=1.000 -i0"Yes" -i1"No"
#430 -t2 -s1"MPG interface type" -s3"0-serial port MPG��1-standard MPG" -m12 -
min=0.000 -max=1.000 -i0"Serial" -i1"Standard"
#431 -t1 -s1"MPG Precision" -m12 -min=0.001 -max=0.01
#432 -t2 -s1"Standard MPG signal Electric Level" -m12 -min=0.000 -max=1.000 -
i0"Low" -i1"High"
#428 -t2 -s1"Enable the ESTOP signal on MPG" -s3"0:not enable,1:enable" -m12 -
min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#429 -t2 -s1"Electric level of ESTOP on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#434 -t2 -s1"A/B phase signal level on MPG" -m12 -min=0.000 -max=1.000 -i0"Low" -
i1"High"
#448 -t2 -s1"MPG control mode" -m12 -min=0.000 -max=1.000 -i0"Open" -i1"Close"
#2028 -t0 -s1"the % of the change in value per X Pulses of the Handwheel" -m12 -
min=1.000 -max=100.000
#441 -t1 -s1"X axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#442 -t1 -s1"Y axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#443 -t1 -s1"Z axis backlash distance" -s2"mm" -m14 -min=0.000 -max=0.999
#444 -t1 -s1"A axis backlash distance" -s2"deg" -m14 -min=0.000 -max=9.999
#250 -t2 -s1"real track paint enable" -m16 -min=0.000 -max=1.000 -i0"disable" -
i1"enable"
#253 -t2 -s1"track paint mode" -m16 -min=0.000 -max=1.000 -i0"Statue Mode" -i1"Line
Mode"
#238 -t1 -s1"IO input filter time width" -s2"ms" -m16 -min=0.001 -max=9999.999
#88 -t2 -s1"enable of beep " -m16 -min=0.000 -max=1.000 -i0"Disable" -i1"Enable"
#2042 -t2 -s1"whether all-zero op. contains the Z-axis" -m16 -min=0.000 -max=1.000
-i0"Yes" -i1"No"
#449 -s1"ZERO"
#450 -s1"GOTOZ"
#451 -s1"HOME"
#452 -s1"PROBE"
#453 -s1"AUTO"
#454 -s1"SIMULATE"
#455 -s1"CONT"
#456 -s1"STEP"
#457 -s1"MPG"
#458 -s1"RESET"
#459 -s1"READY"
#460 -s1"BUSY"
#461 -s1"FRO:"
#462 -s1"SRO:"
#463 -s1"SJR"
#464 -s1"Start Line:"
#465 -s1"2ND"
#466 -s1"syntax check"
#467 -s1"Main Page"
#468 -s1"File Page"
#469 -s1"Param Page"
#470 -s1"Normal Mod"
#471 -s1"X-:gotoz Y-:zero Z-:home"
#472 -s1"A-:probe Start:goto break"
#473 -s1"X-:all gotoz X+:x gotoz"
#474 -s1"Y+:y gotoz Z+:z gotoz"
#475 -s1"A-:go probe X+:mode 3"
#476 -s1"X+:left X-:right Y+:up Y-:down"
#477 -s1"Z-:enter Z+:cancel"
#478 -s1"Y-:all zero X+:x zero"
#479 -s1"Y+:y zero Z+:z zero"
#480 -s1"Z-:all home X+:x home"
#481 -s1"Y+:y home Z+:z home"
#482 -s1 "soft limit:"
#483 -s1 "TRCUT"
#484 -s1 "EDIT"
#485 -s1 "SBK"
#105 -s1 "LOW"
#106 -s1 "Medium"
#107 -s1 "High"
#121 -s1 "Stop"
#122 -s1 "Whether to perform Home operation?"
#8=1.000
#9=1.000
#12=1.000
#13=1.000
#14=1.000
#195=0
#196=0
#2040=0
&&