Professional Documents
Culture Documents
Additional Brackets
Additional Brackets
1
NAME TYPE L (M) W(SPAN)M WIND LOAD, TRIBUTARY AREA (M2) REMARKS TYPE OF CONNECTION
GL 01 C.C.W 7.95 1.7 13.515 FOLLOW CALCULATION OF GL 01 FIX
GL 01 A C.C.W 7.95 1.7 13.515 FOLLOW CALCULATION OF GL 01 FIX
GL 02 STRIP 3 1.246 3.738 FOLLOW CALCULATION OF GL 08 PINNED
GL 03 STRIP 3 1.254 3.762 FOLLOW CALCULATION OF GL 08 PINNED
GL 05 STRIP 3 1.31 3.93 FOLLOW CALCULATION OF GL 42 PINNED
GL 06 STRIP 3.45 1.31 4.5195 FOLLOW CALCULATION OF GL 42 PINNED
GL 07 STRIP 3.45 1.238 4.2711 FOLLOW CALCULATION OF GL 42 PINNED
GL 08 STRIP 3 1.255 3.765 FOLLOW CALCULATION OF GL 08 PINNED
GL 09 STRIP 4.3 1.33 5.719 FOLLOW CALCULATION OF GL 30 FIX
GL 10 STRIP 4.25 1.095 4.65375 FOLLOW CALCULATION OF GL 42 PINNED
GL 11 STRIP 3.58 1.55 5.549 FOLLOW CALCULATION OF GL 30 FIX
GL 12 STRIP 3.75 1.2 4.5 FOLLOW CALCULATION OF GL 42 PINNED
GL 13 STRIP 3 1.38 4.14 FOLLOW CALCULATION OF GL 42 PINNED
GL 14 STRIP 3 1.2 3.6 FOLLOW CALCULATION OF GL 08 PINNED
GL 14 A STRIP 3 1.2 3.6 FOLLOW CALCULATION OF GL 08 PINNED
GL 14 B STRIP 3 1.2 3.6 FOLLOW CALCULATION OF GL 08 PINNED
GL 15 A STRIP 3.45 1.2 4.14 FOLLOW CALCULATION OF GL 42 PINNED
GL 15 B STRIP 3.6 1.2 4.32 FOLLOW CALCULATION OF GL 42 PINNED
GL 15 C STRIP 3.45 1.2 4.14 FOLLOW CALCULATION OF GL 42 PINNED
GL 15 D STRIP 3.45 1.2 4.14 FOLLOW CALCULATION OF GL 42 PINNED
GL 16 STRIP 4.15 1.1 4.565 FOLLOW CALCULATION OF GL 42 PINNED
GL 17 STRIP 3.05 1.12 3.416 FOLLOW CALCULATION OF GL 08 PINNED
GL 18 STRIP 2.96 1.125 3.33 FOLLOW CALCULATION OF GL 08 PINNED
GL 19 STRIP 1.2 0.975 1.17 FOLLOW CALCULATION OF GL 34 PINNED
GL 20 STRIP 1.2 0.975 1.17 FOLLOW CALCULATION OF GL 34 PINNED
GL 21 STRIP 1.2 0.95 1.14 FOLLOW CALCULATION OF GL 34 PINNED
GL 22 STRIP 1.2 0.95 1.14 FOLLOW CALCULATION OF GL 34 PINNED
GL 23 A STRIP 3 1.37 4.11 FOLLOW CALCULATION OF GL 42 PINNED
GL 23 B STRIP 3 1.255 3.765 FOLLOW CALCULATION OF GL 08 PINNED
GL 23 C STRIP 3 1.325 3.975 FOLLOW CALCULATION OF GL 42 PINNED
GL 24 A STRIP 3 1.365 4.095 FOLLOW CALCULATION OF GL 42 PINNED
GL 24 B STRIP 3 1.255 3.765 FOLLOW CALCULATION OF GL 08 PINNED
2
GL 24 C STRIP 3 1.255 3.765 FOLLOW CALCULATION OF GL 08 PINNED
GL 25 STRIP 3.45 1.255 4.32975 FOLLOW CALCULATION OF GL 42 PINNED
GL 26 STRIP 3.45 0.785 2.70825 FOLLOW CALCULATION OF GL 34 PINNED
GL 27 STRIP 3.45 1.255 4.32975 FOLLOW CALCULATION OF GL 42 PINNED
GL 28 STRIP 3.45 1.255 4.32975 FOLLOW CALCULATION OF GL 42 PINNED
GL 29 STRIP 3.45 1.255 4.32975 FOLLOW CALCULATION OF GL 42 PINNED
GL 30 STRIP 4.5 1.185 5.3325 FOLLOW CALCULATION OF GL 30 FIX
GL 31 STRIP 3.15 1.055 3.32325 FOLLOW CALCULATION OF GL 08 PINNED
GL 32 STRIP 3 0.995 2.985 FOLLOW CALCULATION OF GL 08 PINNED
GL 33 STRIP 3.2 1.095 3.504 FOLLOW CALCULATION OF GL 08 PINNED
GL 34 STRIP 2.85 0.7475 2.130375 FOLLOW CALCULATION OF GL 34 PINNED
GL 35 STRIP 2.85 0.7475 2.130375 FOLLOW CALCULATION OF GL 34 PINNED
GL 36 STRIP 2.85 0.695 1.98075 FOLLOW CALCULATION OF GL 34 PINNED
GL 37 STRIP 2.85 0.7475 2.130375 FOLLOW CALCULATION OF GL 34 PINNED
GL 38 STRIP 2.85 0.7475 2.130375 FOLLOW CALCULATION OF GL 34 PINNED
GL 39 STRIP 2.85 0.6975 1.987875 FOLLOW CALCULATION OF GL 34 PINNED
GL 40 STRIP 3.6 1.485 5.346 FOLLOW CALCULATION OF GL 30 FIX
GL 41 STRIP 3.55 1.43 5.0765 FOLLOW CALCULATION OF GL 30 FIX
GL 42 STRIP 3.7 1.29 4.773 FOLLOW CALCULATION OF GL 42 PINNED
GL 43 STRIP 3.5 1.055 3.6925 FOLLOW CALCULATION OF GL 08 PINNED
GL 44 A STRIP 3 1.2 3.6 FOLLOW CALCULATION OF GL 08 PINNED
GL 44 B STRIP 3 1.2 3.6 FOLLOW CALCULATION OF GL 08 PINNED
GL 44 C STRIP 3.025 1.2 3.63 FOLLOW CALCULATION OF GL 08 PINNED
GL 45 STRIP 3.955 1.307 5.169185 FOLLOW CALCULATION OF GL 30 FIX
GL 46 STRIP 3 1.307 3.921 FOLLOW CALCULATION OF GL 42 PINNED
3
www.hilti-me.com
GL 08 BOTTOM , BP THK 6MM Profis Anchor 2.9.1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HST2 M10 hmin1
Return period (service life in years): 50
Seismic/Filling set or any suitable annular gap filling solution
Effective embedment depth: hef = 60 mm, hnom = 69 mm
Material:
Evaluation Service Report: ETA-15/0435
Issued I Valid: 12/21/2017 | -
Proof: SOFA design method + fib (07/2011) - after ETAG testing
Stand-off installation: eb = 0 mm (no stand-off); t = 2 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 150 mm x 130 mm x 2 mm; (Recommended plate thickness: calculated (2 mm))
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm
Base material: uncracked concrete, C40/50, fc,cyl = 40.00 N/mm2; h = 250 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 4
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 5
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 6
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
5 Combined tension and shear loads SOFA (fib (07/2011), section 10.3)
bN bV a Utilization bN,V [%] Status
steel 0.024 0.074 2.000 1 OK
concrete 0.055 0.167 1.500 9 OK
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 7
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid
without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this
calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load
re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in
order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to
limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by
PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed
to ensure a proper installation.
• The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling the gap
with mortar of sufficient compressive strength (e.g. by using the HILTI Seismic/Filling set) or by other suitable means
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 8
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
8 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HST2 M10 hmin1
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm Installation torque: 0.045 kNm
Hole diameter in the fixture: df = 12 mm Hole diameter in the base material: 10 mm
Plate thickness (input): 2 mm Hole depth in the base material: 85 mm
Recommended plate thickness: calculated (2 mm) Minimum thickness of the base material: 120 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use
is required.
75 75
15
3 4
65
100
x
65
1 2
15
40 70 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 9
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 10
GL 08 TOP , BASEPLATE THICKNESS 6 MM
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HST2 M8 hmin1
Return period (service life in years): 50
Effective embedment depth: hef = 47 mm, hnom = 55 mm
Material:
Evaluation Service Report: ETA-15/0435
Issued I Valid: 12/21/2017 | -
Proof: Design method EN 1992-4, Mechanical
Stand-off installation: eb = 0 mm (no stand-off); t = 2 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 140 mm x 120 mm x 2 mm; (Recommended plate thickness: calculated (2 mm))
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm
Base material: uncracked concrete, C40/50, fc,cyl = 40.00 N/mm2; h = 250 mm, partial material safety factor gc = 1.500
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 11
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 12
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 13
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid
without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this
calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 14
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load
re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in
order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to
limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by
PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters of the
clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed
to ensure a proper installation.
• For the determination of the Psi_re,v (concrete edge failure) a concrete cover of the edge reinforcement c = 30 mm is assumed
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 15
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
7 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HST2 M8 hmin1
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm Installation torque: 0.020 kNm
Hole diameter in the fixture: df = 9 mm Hole diameter in the base material: 8 mm
Plate thickness (input): 2 mm Hole depth in the base material: 70 mm
Recommended plate thickness: calculated (2 mm) Minimum thickness of the base material: 100 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use
is required.
70 70
15
2
60
90
x
60
1
15
70 70
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 16
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 17
GL 34 , BP THK 6 MM
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HST2 M12 hmin1
Return period (service life in years): 50
Seismic/Filling set or any suitable annular gap filling solution
Effective embedment depth: hef = 70 mm, hnom = 80 mm
Material:
Evaluation Service Report: ETA-15/0435
Issued I Valid: 12/21/2017 | -
Proof: SOFA design method + fib (07/2011) - after ETAG testing
Stand-off installation: eb = 0 mm (no stand-off); t = 3 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 150 mm x 130 mm x 3 mm; (Recommended plate thickness: calculated (3 mm))
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm
Base material: uncracked concrete, C40/50, fc,cyl = 40.00 N/mm2; h = 250 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 18
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 19
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
5 Combined tension and shear loads SOFA (fib (07/2011), section 10.3)
bN bV a Utilization bN,V [%] Status
steel 0.039 0.074 2.000 1 OK
concrete 0.068 0.174 1.500 9 OK
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 20
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid
without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this
calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load
re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in
order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to
limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by
PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed
to ensure a proper installation.
• The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling the gap
with mortar of sufficient compressive strength (e.g. by using the HILTI Seismic/Filling set) or by other suitable means
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 21
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
8 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HST2 M12 hmin1
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm Installation torque: 0.060 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 12 mm
Plate thickness (input): 3 mm Hole depth in the base material: 97 mm
Recommended plate thickness: calculated (3 mm) Minimum thickness of the base material: 140 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use
is required.
75 75
20
2
65
90
x
65
1
20
75 75
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 22
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 23
www.hilti-me.com
GL 34 , TOP BP,THK 6 MM Profis Anchor 2.9.1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HST2 M8 hmin1
Return period (service life in years): 50
Effective embedment depth: hef = 47 mm, hnom = 55 mm
Material:
Evaluation Service Report: ETA-15/0435
Issued I Valid: 12/21/2017 | -
Proof: Design method EN 1992-4, Mechanical
Stand-off installation: eb = 0 mm (no stand-off); t = 1 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 140 mm x 120 mm x 1 mm; (Recommended plate thickness: calculated (1 mm))
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm
Base material: uncracked concrete, C40/50, fc,cyl = 40.00 N/mm2; h = 250 mm, partial material safety factor gc = 1.500
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 24
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 25
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 26
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid
without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this
calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 27
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load
re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in
order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to
limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by
PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters of the
clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed
to ensure a proper installation.
• For the determination of the Psi_re,v (concrete edge failure) a concrete cover of the edge reinforcement c = 30 mm is assumed
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 28
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
7 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HST2 M8 hmin1
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm Installation torque: 0.020 kNm
Hole diameter in the fixture: df = 9 mm Hole diameter in the base material: 8 mm
Plate thickness (input): 1 mm Hole depth in the base material: 70 mm
Recommended plate thickness: calculated (1 mm) Minimum thickness of the base material: 100 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use
is required.
70 70
15
2
60
90
x
60
1
15
70 70
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 29
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 30
www.hilti-me.com
GL 42 BOTTOM , BP THK 6 MM Profis Anchor 2.9.1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HST2 M12 hmin1
Return period (service life in years): 50
Seismic/Filling set or any suitable annular gap filling solution
Effective embedment depth: hef = 70 mm, hnom = 80 mm
Material:
Evaluation Service Report: ETA-15/0435
Issued I Valid: 12/21/2017 | -
Proof: SOFA design method + fib (07/2011) - after ETAG testing
Stand-off installation: eb = 0 mm (no stand-off); t = 3 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 180 mm x 150 mm x 3 mm; (Recommended plate thickness: calculated (3 mm))
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm
Base material: uncracked concrete, C40/50, fc,cyl = 40.00 N/mm2; h = 250 mm
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 31
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 32
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 33
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
5 Combined tension and shear loads SOFA (fib (07/2011), section 10.3)
bN bV a Utilization bN,V [%] Status
steel 0.021 0.065 2.000 1 OK
concrete 0.052 0.161 1.500 8 OK
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 34
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid
without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this
calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load
re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in
order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to
limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by
PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed
to ensure a proper installation.
• The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling the gap
with mortar of sufficient compressive strength (e.g. by using the HILTI Seismic/Filling set) or by other suitable means
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 35
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
8 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HST2 M12 hmin1
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm Installation torque: 0.060 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 12 mm
Plate thickness (input): 3 mm Hole depth in the base material: 97 mm
Recommended plate thickness: calculated (3 mm) Minimum thickness of the base material: 140 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use
is required.
90 90
20
3 4
75
110
x
75
1 2
20
55 70 55
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 36
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 37
www.hilti-me.com
GL 42 , TOP , BP THK 6 MM Profis Anchor 2.9.1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HST2 M8 hmin1
Return period (service life in years): 50
Effective embedment depth: hef = 47 mm, hnom = 55 mm
Material:
Evaluation Service Report: ETA-15/0435
Issued I Valid: 12/21/2017 | -
Proof: Design method EN 1992-4, Mechanical
Stand-off installation: eb = 0 mm (no stand-off); t = 2 mm
Anchor plate: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm2; gMs = 1.000
lx x ly x t = 140 mm x 120 mm x 2 mm; (Recommended plate thickness: calculated (2 mm))
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm
Base material: uncracked concrete, C40/50, fc,cyl = 40.00 N/mm2; h = 250 mm, partial material safety factor gc = 1.500
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 38
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 39
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 40
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are valid
without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in this
calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 41
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
6 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This means load
re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be sufficiently stiff, in
order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate thickness with FEM to
limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate assumption is valid is not carried out by
PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters of the
clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be followed
to ensure a proper installation.
• For the determination of the Psi_re,v (concrete edge failure) a concrete cover of the edge reinforcement c = 30 mm is assumed
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 42
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
7 Installation data
Anchor plate, steel: S 275; E = 210,000.00 N/mm2; fyk = 275.00 N/mm Anchor type and diameter: HST2 M8 hmin1
Profile: Rectangular hollow, ; (L x W x T) = 125 mm x 50 mm x 2 mm Installation torque: 0.020 kNm
Hole diameter in the fixture: df = 9 mm Hole diameter in the base material: 8 mm
Plate thickness (input): 2 mm Hole depth in the base material: 70 mm
Recommended plate thickness: calculated (2 mm) Minimum thickness of the base material: 100 mm
Drilling method: Hammer drilled
Cleaning: Manual cleaning of the drilled hole according to instructions for use
is required.
70 70
15
2
60
90
x
60
1
15
70 70
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 43
www.hilti-me.com Profis Anchor 2.9.1
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 1/24/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan 44