Professional Documents
Culture Documents
Abb Utilities GMBH: Application
Abb Utilities GMBH: Application
Application
The 23AE21 board records up to eight analog mea- low-pass filter suppresses non line frequency ac dis-
sured values. The 23AE21 board allows it to connect turbance.
all typical measured value ranges
The AD-converter, operating with the sigma-delta
It can be configured for the following measurand method scans with a higher resolution and has addi-
ranges by simple switches and jumpers: tional algorithms for a high suppression of line fre-
V 2 mA quency and line harmonics interference voltages.
Even for a deviation of =10 % of the line frequency
V 5 mA
there is still given a suppression of > 45 dB. The in-
V 10 mA ternal high resolution allows it to scan all measuring
V 20 mA ranges (exception: 2 V DC (11 bit +sign)) with the
V 40 mA same resolution (12 bit + sign) on one board. A
9th channel is used for automatic zero calibration.
V 2 V DC
V 0 ... + 20 V DC
Other effective ranges and live ziro signals become AD- -converter
generated out of these ranges through conversion of Multiplexer Connection
the communication unit CMU.
+
EA11
Protection circuit
D
23AE20 board.
B
U
Characteristics S --
EA10
Basic checks and computing intensive, cyclical pro- M Input circuit
cessing functions will already be done on the board
O
and remove therefore the burden from the central
unit. Relevant changes transmits the board as event D +
U A EA81
via the peripheral bus. Input circuit --
L EA80
The 8 differential inputs are not potentially isolated E
against the RTU560 power supply.
The analog input board 23AE20 can carry out the fol- The microcontroller controls the A/D converter and
lowing processing functions on the measured val- executes all of the processing functions of the con-
ues: figured measured values within the conversion time.
V Zero point monitoring Furthermore the microcontroller is responsible for in-
V Switch- -over recognition teractive communication with the RTU560 system
V Smoothing bus. All configuration characteristics and proces-
sing parameters are downloaded from the CMU via
V Threshold value monitoring on absolute
the RTU system bus.
value or with accumulation and periodic
background transmission. During initialization and operation the board carries
V Limit value monitoring with event recording out a number of tests. If a fault occurs it is reported to
Measuring range and line frequency are easily to the CMU. All fault conditions impairing the function of
configure by switch registers respectively jumpers. the board are displayed as common fault signal with
The microcontroller needs these configurations pa- a light emitting diode (ST) on the front panel. A failure
rameters to setup the AD-converter. of the board is detected by the CMU.
60 62.5 500
50 72.5 580
16.6 202.5 1620
Technical Data
In addition to the RTU560 general technical data, the following applies:
Input channels Power Supply
Inputs: 8; differential inputs Supply: 5V / max. 230 mA
Measuring ranges: 2 mA
5 mA Mechanical Layout
10 mA
20 mA Printed circuit 3HE, Euro- -card format
40 mA board: (160 x 100 mm)
2 V DC / 0...+20 V DC Front panel: 4R, 1 slot (20 mm)
Weight: approx. 0.3 kg
Shunt / impedance 50 Ω at 40 and 20 mA
150 Ω at 10 to 2 mA
110 kΩ at 2 V and 20 V DC Connection Type
Continuous load max. 80 mA Connector: indirect, 48 pole
without destruction: for range 40 and 20 mA Type F DIN 41612
max. 40 mA
for range 10/5 to 2 mA
max. 38 V resp. Test Voltages
max. 0.5 mA Insulation voltage 2.5 kV AC
for range 2 and 20 V DC withstand test: IEC 60870-2-1 (VW 3)
Resolution: 12 bit + sign = 100% Impulse voltage 4 kV (1,2/50)
all ranges except 2 V DC withstand test: IEC 60664-1
11 bit + sign for 2 V DC Overvoltage Category III