Professional Documents
Culture Documents
ATT III - 6. Operate Fuel, Lubrication, Ballast and Other Pumping Systems and Associated Control Systems
ATT III - 6. Operate Fuel, Lubrication, Ballast and Other Pumping Systems and Associated Control Systems
Operate fuel, lubrication, ballast and other pumping systems and associated control
systems
8. Why does every replacement of spare part need to be recorded on the date of replacement?
a. In order to know for the unlucky date
b. So that we know the running hours
c. In order to know which one breaks faster
d. In order to know the quality of the spare part
9. Why after overhaul the main engine must be tested before sailing?
a. So that if there are things or components that don't fit, they can be repaired
immediately
b. Just make sure that the engine is running and there are no more problems
c. Make sure that everything is working normally and ready to sail
d. All answers are correct
11. If you are a 3rd engineer and have responsibility for a steam boiler, one day you forget to
burn manually and steam until the safety valve is more than working. But at that time the
safety valve did not work automatically, what did you do as a 3rd engineer?
a. Immediately report to the chief engineer
b. Leaving because the safety valve auto is damaged
c. Pulling the safety valve manually and turning off the valve
d. Run away immediately afraid of an explosion
12. What is a propeller pitch control transmission?
a. A ship's engine that moves forward and backward must first turn off.
b. An engine that moves forward and backward without turning off the engine
c. An engine of the ship forward and backward using only the propeller blades
d. Mechanism of ships that move forward and aft only uses a motor
14. Why does the O-ring need to be given a molicot when installing?
a. To be strong
b. To be sticky and durable
c. So that it doesn't stick and is easy to remove during overhaul
d. So that it's tight and doesn't leak
17. When the main engine rpm is still low, and the turbo has not worked optimally to supply the
rinse air, where is the rinse air taken from?
a. From the engine room
b. From the main engine blower
c. From the wind all around
d. Open the scavenge to let the rinse air in
20. A machine that can convert electric power into mechanical power is?
a. Dry battery
b. Generator
c. Dynamo
d. Electric motor
28. What is the possible cause of a Main Diesel difficult to start, except …
a. Explanation air pressure is too low
b. The spraying of fuel in the cylinder is late and less than perfect
c. Type of fuel used
d. Air staring valve stuck due to corrosion
29. What causes the white smoke on the main motor?
a. Fuel injection pressure is too low
b. No compression in combustion chamber
c. Lubricating oil that is no longer suitable for use
d. Incorrect fuel ratio
32. What causes high exhaust valve, burnt exhaust gas manifold, high temperature?
a. Lack of heat fuel F.O B
b. Low fuel rag position
c. The performance of the atomizer is not good
d. High oil temperature
33. To what degree will the injector atomize the fuel?
a. 20 degrees before TDC
b. 15 degrees after TDC
c. 17 degrees before TDC
d. 19 degrees after TDC
39. After the purifier is used and will be stopped, the steps that must be taken are
a. brake
b. Blow up
c. Blow down
d. Power off
40. Choose one of the statements below which is not a FWG operating procedure!
a. Starts the ejector pump
b. Opens the ejector inlet valve
c. Opens the brine overboard valve
d. Blow up FWG
41. Which of the following statements is the correct way to operate the cooling system?
a. Flow the condenser, Open the suction valve and press the compressor, operate the
condenser motor, check low and high pressure and oil.
b. Check low and high pressure and oil, open the suction valve and press the
compressor, operate the condenser, drain the condenser.
c. Check low and high pressure and oil, operate the compressor, open the suction
valve and press the compressor, operate the motor.
d. Flow the condenser, check the low and high pressure and oil, operate the motor,
open the intake valve and press
42. The liquid chemical for removing rust is called
a. Rust remover
b. Sulfuric acid
c. Hydrogen
d. SAF Acid
43. How many degrees of hot steam does the purifier need to work?
a. 45 – 50 degree
b. 40 – 50 degree
c. 65 – 70 degree
d. 50 – 60 degree
e. I don't know
44. The high pressure pump in the engine to pump fuel into the injectors is called …
a. Bosch pump
b. FO Pump
c. Feed Pump
d. Circulating Pump
e. I don’t know
45. The part of the OWS that functions as a bilge water reservoir which is separated by a bilge
separator from oil deposits is called?
a. Bilge Pump
b. Bilge Separator
c. Coaliser
d. Disc
e. I don't know