Professional Documents
Culture Documents
PMS预防维修prevent Maintenance System-30DT
PMS预防维修prevent Maintenance System-30DT
PMS预防维修prevent Maintenance System-30DT
( GW38 / ZJ30DT )
Contents/内容
1. DRAW WORKS MAINTENANCE/绞车维护………………………………………………………………………………..……………………………………………………… 3
2. PZ30 HYDRAULIC DISC BRAKE MAINTENANCE/液压盘刹维护 ………………………………………………………………………………………………………………… 4
3. MAST AND SUBSTRUCTURE MAINTENANCE/井架及底座………………………………………………………………………………………………………………………… 6
4. HOIST SYSTEM MAINTENANCE/提升系统维护………………………………………………………………………………………………………………………...…………… 7
5. TRANSMISSION SYSTEM MAINTENANCE/传输装置维护………………………………………………………………… ……………………………………………………… 8
6. PNEUMATIC CONTROL SYSTEM MAINTENANCE/气动控制系统维护…………………………………………………………………………………………………………… 9
7. SEMI-TRAILER MAINTENANCE/半拖装置维护…………………………………………………………………………………………………………………………...……………9
1
GW19—ZJ30DT—PMS
1 Fast line clamp plate/快绳头 All ready and no loose /正常,无松动 Shift 每班
2 Break/刹车 Flexible and reliable/有弹性及可靠 shift 每班
3 Break block/刹车片 No serious wear , no crack/无严重磨损,无裂纹 Shift 每班
4 Clearance between Break rim and break band /刹带与刹车片的 Uniformity/均匀度 shift 每班
间隙
5 Break device , emergency break/刹车设施,紧急刹车 Normal/正常 shift 每班
6 Every shift end , bear cover ,chain box/链条箱,轴承盖 No leakage oil , bearing temperature rise normal/不漏油,轴承温度正常 shift 每班
7 Air control system/气控系统 No air leakage /不漏气 shift 每班
8 Lubrication system /润滑系统 No oil leakage/不漏油 shift 每班
2
GW19—ZJ30DT—PMS
3
GW19—ZJ30DT—PMS
表)
2 Oil level (level gauge)/油位(油位表) Fill L-HV32 low temperature anti-wear oil in winter , Fill L-HM64 anti-wear oil in summer , oil level Shift 每班
should over lowest oil level point.冬季补充 L-HV32 低温抗磨机油,夏季补充 L-HM64 抗磨机油,
油位应该高于最低油位点。
3 Crown saver loop Push the crown saver valve and inspect the brake to ensure irs normal. 检查过卷阀并检查刹车确保正 Shift 每班
常工作
4 System pressure/系统压力 6 Mpa/6 兆帕 Shift 每班
5 Clearance between brake block to disc/刹带片到刹车鼓 Single side clearance of working tong is 1 mm,工作钳单边距离为 1 毫米,安全钳单边距离为 0.5 毫 Daily 每日
间距离 米 Single side clearance of working tong id 0.5 mm.
6 Block thickness/刹车片厚度 Wear groove should not be flat .磨损槽未变平 Daily 每日
7 All pipes and joints/所有管线及接头 The seal condition is good and there is no leakage.良好密封,无滴漏 Daily 每日
8 Quick-joint 快速接头 No leakage , damage and image joint.无漏失,损坏 Daily 每日
4
GW19—ZJ30DT—PMS
换或修理损坏的部件
15 Oil , oil tank and filter elements 油,油罐和滤 Exchange new oil exchange filter elements, clean oil tank, loop and hydraulic valve.更换 Biannual 每半年
芯 机油或过滤器,清洁油罐和液压阀
16 Designed pressure 设计压力 Re-adjust the system pressure on the base of rule by experienced worker, including flood Biannual 每半年
valve, constant pressure valve. Reference the gauge pressure.根据规范,由有经验的人
员调校系统压力,包括 flood valve,常压阀,参考仪表压力
17 Structure parts inspection 结构部件检查 Inspect all structure parts of theirs quality condition.检查所有结构部件 Biannual 每半年
18 Dish spring of normal close valve 常闭阀盘式 All spring set should be exchanged.所有弹簧座必须更换 Biannual 每半年
弹簧
19 Brake disc 盘刹 Inspect the brake disc of its fabrication, deformation, crake, etc. exchange if necessary.检 Biannual 每半年
查盘刹的制造,变形,裂纹等,如有必要进行更换
5
GW19—ZJ30DT—PMS
6
GW19—ZJ30DT—PMS
7
GW19—ZJ30DT—PMS
针和滑轮组有裂纹
8
GW19—ZJ30DT—PMS
9
GW19—ZJ30DT—PMS
磨损
Loose and damage of √ No loose and damage 无 严
Lines 钢丝 connections 松 动 和 连 接 损 重磨损
绳 坏
Inter cable damage 内部电缆 √ No damage 无磨损
损坏
Check item 检查项目 Check interval 检查间隔 Criterion 细则 Remarks 备注
Function 功能 √ √ √ √ Normal 正常
Lights 灯
Black and damage 黑色和损 √ No black and damage 无 黑
坏 色和损坏
Traction pin Wear and crack 磨损和裂纹 √ √ √ √ Standard ¢88.9 标准¢88.9
eq
th
er
O
10
GW19—ZJ30DT—PMS
管线和连接 每 2 年检查安全绳
Check item 检查项目 Check interval 检查间隔 Criterion 细则 Remarks 备注
车
11
GW19—ZJ30DT—PMS
日常 month 一 3月 年
月
12
GW19—ZJ30DT—PMS
13
GW19—ZJ30DT—PMS
曲轴
Criterion 细则 Remarks 备注
Check item 检查项目 Check interval 检查内容
Clearance between them 间 Max. clearance shall be 0.6- Adjust if beyond the
Brake drum and brake friction disc 刹车滚
隙 0.7mm range 如 果 在 范 围
最 大 间 隙 为 shall be 0.6- 外,进行调整
0.7mm
Friction disc damage 摩擦盘 Change it if wear to limit Change friction disc
损坏 position 如果磨损到限制位 if rivet head lower
置,进行更换 than friction disc 1
茼和刹车盘
mm 如 果 rivet head
低于摩擦盘 1mm,
更换摩擦盘
14
GW19—ZJ30DT—PMS
deformation 裂 纹 损 坏 和 变 deformation 无 裂 纹 损 坏 和
形 变形
纹和损坏 重,更换
Tire pattern depth and √ √ √ √ Remaining pattern more As per wear mark 根
abnormal wear 胎 纹 路 深 度 3mm 确保纹路深度不低于 据磨损痕迹
和异常磨损 3mm
Metal chips,stone and other √ √ √ √ Remove completely 完 全 拆
foreign matters in tire 轮 胎 除
中的金属片或外部物质
15
GW19—ZJ30DT—PMS
16
GW19—ZJ30DT—PMS
油封老化和损坏
Air spring 气弹簧 If the air bag piston is dirt 是 √ √ √ Clean if necessary 如有必要
否空气包活塞脏 进行清洁
Suspension frame
17
GW19—ZJ30DT—PMS
18
GW19—ZJ30DT—PMS
19
GW19—ZJ30DT—PMS
12 Cooling system(Conventional Test for SCA or obtain level l analysis, Add SCA if First 250 hours or 13000L(3400 gal) of fuel 每 250
coolant/Antifreeze only)冷却系统(常规冷 required .测试 SCA 或取得 1 级分析,如有必要 小时或 13000 升燃油
却剂/防冻剂) 加 SCA。
13 Fuel system 燃油系统 Clean primary filter/ replace final filters 清洁初级 First 250 hours or 13000L(3400 gal) of fuel 每 250
过滤器/更换终极过滤器 小时或 13000 升燃油
14 Fuel tank 燃油罐 Drain water 排污水 First 250 hours or 13000L(3400 gal) of fuel 每 250
小时或 13000 升燃油
15 Belts, hoses and clamps 皮带,软管线和卡 Inspect/Check/Replace if necessary 如 有 必 要 检 First 250 hours or 13000L(3400 gal) of fuel 每 250
子 查更换 小时或 13000 升燃油
16 Fan drive (if equipped)风扇驱动(如果装 Lubricate bearing 润滑轴承 First 250 hours or 13000L(3400 gal) of fuel 每 250
备) 小时或 13000 升燃油
17 Batteries 蓄电池 Check/Clean 检查清洁 First 250 hours or 13000L(3400 gal) of fuel 每 250
小时或 13000 升燃油
18 Radiator fins/Aftercooler 散热器/后冷器 Inspect / Check 检查 First 250 hours or 13000L(3400 gal) of fuel 每 250
小时或 13000 升燃油
Item Inspection item 检查内容 Implement Inspection Cycle
序号
19 Engine protection devices 发动机自动保护 Inspect/Check 检查 Every 1000 hours or 51000 L(13500 gal) of fuel 每
装置 1000 小时或 51000 升燃油
20 Fuel control linkage 燃油控制连接管线 Check/Lubricate 检查/润滑 Every 1000 hours or 51000 L(13500 gal) of fuel 每
1000 小时或 51000 升燃油
21 Cooling system(Long life Add Extender 加增量剂 Every 3000 hours or 153500 L (40500 gal) of fuel 每
coolant/Antifreeze only) 冷却剂(长寿命 3000 小时或 153500 升燃油
冷却剂/防冻剂)
22 Cooling system(Conventional coolant. Drain/Clean/Replace Coolant 排出/清洁和更换冷 Every 3000 hours or 153500 L (40500 gal) of fuel 每
20
GW19—ZJ30DT—PMS
10.FOR MUD PUMP OF CAT 3512 ENGINE MAINTENANCE 泥浆泵的 CAT 3512 发动机维护保养
Item Inspection item 检查内容 Implement 要求和实施 Inspection Cycle 检查周期
21
GW19—ZJ30DT—PMS
序号
1 Air starting motor lubricator oil level 启动马达 Check 检查 Daily 每日
润滑油位
2 Air tank moisture and sediment 空气罐的雾气 Drain 排出 Daily 每日
和沉积物
3 Cooling system coolant level 冷却剂液位 Check 检查 Daily 每日
4 Engine air cleaner service indicator 空气清洁器 Inspect 检查 Daily 每日
工作指示仪
5 Engine air precleaner 发动机前空气清洁器 Clean 清洁 Daily 每日
6 Engine oil filter differential pressure 机油滤子 Check 检查 Daily 每日
压力
7 Engine oil lever 发动机机油油位 Check 检查 Daily 每日
8 Fuel system fuel filter differential pressure 燃油 Check 检查 Daily 每日
系统燃油过滤器 differential pressure
9 Fuel tank water and sediment 燃油罐水和沉积 Drain 排出 Daily 每日
物
10 Instrument panel 仪表盘 Inspect 检查 Daily 每日
11 Walk-Around Inspection 巡回检查 Daily 每日
12 Engine valve lash Inspect/Adjust 检查调整 Initial 250 service house (or at first oil change)
13 Fuel injector 燃油注入器 Inspect/Adjust 检查调整 Initial 250 service house (or at first oil change)
14 Magnetic pickups 磁吸 Clean/Inspect 清洁检查 Initial 250 service house (or at first oil change)
15 Alternator and Fan Belts 转化器和风扇皮带 Inspect/Adjust/Replace 检查调 Every 250 service hours 每 250 个工作小时
整更换
16 Battery electrolyte level 蓄电池电解液位 Check 检查 Every 250 service hours 每 250 个工作小时
Item Inspection item 检查内容 Implement 要求和实施 Inspection Cycle
22
GW19—ZJ30DT—PMS
17 Cooling system supplemental coolant Test/Add 测试补充 Every 250 service hours 每 250 个工作小时
additive(SCA) 冷 却 剂 补 充 冷 却 添 加 剂
(SCA)
18 Engine oil sample 机油油样 Obtain 取样 Every 250 service hours 每 250 个工作小时
19 Engine oil and filter 发动机机油和过滤器 Change 更换 Every 250 service hours 每 250 个工作小时
20 Fan drive bearing 风扇驱动轴承 Lubricate 润滑 Every 250 service hours 每 250 个工作小时
21 Hoses and clamps 软管线和卡子 Inspect/Replace 检查更换 Every 250 service hours 每 250 个工作小时
22 Radiator 散热器 Clean 清洁 Every 250 service hours 每 250 个工作小时
23 Engine oil and filter 发动机机油和过滤器 Change 更换 Every 500 service hours 每 500 个工作小时
24 Cooling system coolant analysis(level ll)冷却系 Obtain 取样 Every 1000 service hours 每 1000 个工作小时
统冷却剂分析
25 Engine 发动机 Clean 清洁 Every 1000 service hours 每 1000 个工作小时
26 Engine crankcase breather 发动机曲轴箱 Clean 清洁 Every 1000 service hours 每 1000 个工作小时
27 Engine oil and filter 发动机机油和过滤器 Change 更换 Every 1000 service hours 每 1000 个工作小时
28 Engine protective devices 发动机自动保护装置 Check 检查 Every 1000 service hours 每 1000 个工作小时
29 Fuel system primary filter 燃油系统初级过滤 Clean/Inspect/Replace 清 洁 检 Every 1000 service hours 每 1000 个工作小时
器 查更换
30 Fuel system secondary filter 燃油系统二级过滤 Replace 更换 Every 1000 service hours 每 1000 个工作小时
器
31 Actuator control linkage 启动器控制连接 Lubricate 润滑 Every 2000 service hours 每 2000 个工作小时
32 Air starting motor lubricator bowl 启动马达润 Clean 清洁 Every 2000 service hours 每 2000 个工作小时
滑杯
33 Crankshaft vibration damper 曲轴减震器 Inspect 检查 Every 2000 service hours 每 2000 个工作小时
34 Engine mounts 发动机安装螺栓 Check 检查 Every 2000 service hours 每 2000 个工作小时
35 Engine valve lash 发动机阀间隙 Inspect/Adjust 检查调整 Every 2000 service hours 每 2000 个工作小时
23
GW19—ZJ30DT—PMS
36 Fuel injector 燃油注入器 Inspect/Adjust 检查调整 Every 2000 service hours 每 2000 个工作小时
37 Magnetic pickups 磁吸 Clean/Inspect 清洁和检查 Every 2000 service hours 每 2000 个工作小时
38 Cooling system coolant(DEAC) 冷却系统冷却 Change 更换 Every 3000 service hours or 3 Years 每 3000 个工作小时或 3 年
剂
Item Inspection item 检查内容 Implement 要求和实施 Inspection Cycle 检查周期
39 Cooling system coolant extender(ELC) 冷 却 系 Add 补充 Every 3000 service hours or 3 Years 每 3000 个工作小时或 3 年
统冷却剂增量剂
40 Alternator 转化器 Inspect 检查 Every 6000 service hours or 6 years 每 6000 个工作小时或 6 年
41 Cooling system coolant(ELC)冷却系统冷却剂 Change 更换 Every 6000 service hours or 6 years 每 6000 个工作小时或 6 年
42 Cooling system water temperature regulator 冷 Replace 替换 Every 6000 service hours or 6 years 每 6000 个工作小时或 6 年
却系统水温调节器
43 Starting motor 启动马达 Inspect 检查 Every 6000 service hours or 6 years 每 6000 个工作小时或 6 年
44 Turbocharger 涡轮增压器 Inspect 检查 Every 6000 service hours or 6 years 每 6000 个工作小时或 6 年
45 Water pump 水泵 Inspect 检查 Every 6000 service hours or 6 years 每 6000 个工作小时或 6 年
46 Overhaul( Top End)大修(上部) Between 7500 and 11000 service hours 在 7500-11000 个工作小时
间
47 Overhaul considerations 大修考虑 Between 7500 and 11000 service hours 在 7500-11000 个工作小时
间
48 Overhaul (Top End) 大修(上部) Between 15000 and 22000 service hours 在 15000-22000 小时之间
49 Overhaul considerations 大修考虑 Between 15000 and 22000 service hours 在 15000-22000 小时之间
50 Overhaul( Major)大修(主要部分) Between 15000 and 22000 service hours 在 15000-22000 小时之间
51 Overhaul considerations 大修 Between 15000 and 22000 service hours 在 15000-22000 小时之间
24
GW19—ZJ30DT—PMS
25
GW19—ZJ30DT—PMS
个工作小时或每年
18 Battery electrolyte level 蓄电池电解液位 Check 检查 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
19 Belts 皮带 Inspect/Adjust/Replace 检查调整和替换 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
20 Cooling system coolant sample ( level 1) Obtain 取样 Every 9500 L ( 2500 US gal ) of Fuel or 250
冷却剂样品(1 级) service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
21 Cooling system supplemental coolant Test/Add 测试/补充 Every 9500 L ( 2500 US gal ) of Fuel or 250
additive(SCA)冷却系统补充冷却添加剂 service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
Item Inspection item 检查内容 Implement 实施和要求 Inspection Cycle 检查周期
22 Engine crankcase breather 发动机曲轴箱 Clean 清洁 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
23 Engine oil sample 机油油样 Obtain 取样 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
24 Engine oil and filter 发动机机油和过滤 Change 更换 Every 9500 L ( 2500 US gal ) of Fuel or 250
器 service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
25 Fuel system secondary filter 燃油系统二 Replace 替换 Every 9500 L ( 2500 US gal ) of Fuel or 250
级过滤器 service hours or Yearly 每 9500 升燃油或 250
26
GW19—ZJ30DT—PMS
个工作小时或每年
26 Fuel tank water and sediment 燃 油 罐 水 Drain 排出 Every 9500 L ( 2500 US gal ) of Fuel or 250
和沉积物 service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
27 Hoses and clamps 软管线和卡子 Inspect/Replace 检查和更换 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
28 Radiator 散热器 Clean 清洁 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
29 Rotating rectifier 旋转整流器 Check 检查 Every 9500 L ( 2500 US gal ) of Fuel or 250
service hours or Yearly 每 9500 升燃油或 250
个工作小时或每年
30 Fan drive bearing 风扇皮带驱动轴承 Lubricate 润滑 Every 19000L (5000 US gal) of fuel or 250
Service hours 每 19000 升燃油或 250 个工作
小时
31 Fuel system primary filter (water Replace 替换 Every 19000L (5000 US gal) of fuel or 550
separator) Element 燃油系统初级过滤器 Service hours 每 19000 升燃油或 550 个工作
(水分离器) 小时
32 Engine protective devices 发动机自动保 Check 检查 Every 28400 L ( 7500 US gal) of fuel or 1000
护装置 service hours 每 28400 升燃油或 1000 个工
作小时
33 Cooling system coolant (DEAC) 冷 却 系 Change 更换 Every 114000 L (30000 US gal) of Fuel or
统冷却剂 3000 service hours or 2 years 每 114000 升燃
油或 3000 工作小时或 2 年
27
GW19—ZJ30DT—PMS
28
GW19—ZJ30DT—PMS
29
GW19—ZJ30DT—PMS
1 Oil level after stoping the pump , 停泵后检 If it is too low, it should be added to required level 如果 Daily 每日
查油位 太低,补充的需要的油位
2 If the readings of pressure gauge of When the pressure is too low, the cause should be found Daily 每日
lubricating oil pump are normal . 是否润滑 at once.如果压力过低,立即检查原因
油泵的压力表读数正常
3 If the dampener works normally 是否泵的 Check 检查 Daily 每日
空气包工作正常
30
GW19—ZJ30DT—PMS
9 Check if the valve bonnets are loose every Coat lubricant on the thread when tightening 在 紧 固 Daily 每日
four hours.每 4 小时检查阀盖是否松动 时,给丝扣抹上黄油.
10 Check if the safety valves are reliable. 检查 Daily 每日
安全阀是否可靠
11 Check if the pre-charging pressure of Daily 每日
discharge pulsation dampener is normal
when stopping the pump. 停泵后检查空气
包预充压力是否正常
12 Observe the alarm bore 观察报警孔 If the mud is discharged , the related seal ring should be Daily .每日
changed .如果有泥浆排出,相关的密封圈需要更换
31
GW19—ZJ30DT—PMS
32
GW19—ZJ30DT—PMS
abnormal phenomena. 检 查 轴 和 曲 轴 是 否
正确,采取措施防止异常现象发生
27 Check the bearing of power end .检查动力 The damaged one should be changed.损坏的部件需要 Yearly 每年
端的轴承 更换
28 Check the seal of rear cover and crank shaft If the seal is not good, it should be changed .如果密封不 Yearly 每年
end cover .检查后盖密封和曲轴端盖 好,需要更换
33
GW19—ZJ30DT—PMS
业 1000 小时后保养
5 Replace the fluid filter element and gasket 更换流体过滤器元件和 Maintenance every 1000 hours of operation 作
垫子 业 1000 小时后保养
6 Replace the air filter element , if necessary 如有必要,更换空气 Maintenance every 1000 hours of operation 每
滤子元件 1000 小时保养
7 Replace your fluid filter element and the gasket under any of the a. Every 1000 hours 每 1000 小 Fluid filter maintenance 流体过滤器保养
following conditions, whichever occurs firs 在以下条件下,更换 时
流体过滤器元件和垫子 b. Every 6 months 每 6 个月
c. As indicated by the
maintenance gauge. 如 仪 表
指示
8 Replace the separator elements when you separator maintenance Separator maintenance 分离器保养
gauges show red or after one year, whichever comes first. The
separator elements must be replaced. Do not clean the separator
elements.在分离器表显示红色或在一年后,更换分离器元件,
不要清洁分离器元件
14 .THE CONTROL SYSTEM FOR SURFACE MOUNTED BOP STACKS maintenance 地面 BOP 组的控制系统维护保养
Item Inspection item 检查内容 Implement 要求和实施 Inspection Cycle 检查周期
序号
1 Remove and check the oil strainer and filter screens of the intake on After use , should be take the Every time 每次
the top of the oil tank .检查油罐的吸入口的过滤器和 screens out and wash them
carefully in order to protect them
34
GW19—ZJ30DT—PMS
35
GW19—ZJ30DT—PMS
36
GW19—ZJ30DT—PMS
37
GW19—ZJ30DT—PMS
38
GW19—ZJ30DT—PMS
set H2S alarm , 2 set combustible gas alarm , mounted on wellhead adjust , 识别器检查,报警闸门
and 1# mud tank .H2S 和组合气体报警识别器,4 个报警位置: 调节
2 套 H2S 警报,2 套组合气体报警,安装在井口和 1 号罐。 parameter standardization ( zero ,
mearsuring range , sensitivity )参
数标准(零,测量范围,敏感
度)
setting ( gas detected , range ,
unit ),设置(气体识别,范围)
Check if all parts fasten 检查部 Monthly 每月
件是否紧固
Check if cable is in good Monthly 每月
condition .检查电缆
Check if fuse in good condition Monthly
Check fault handling system At any moment 任何时候
display screen clue on,eliminate
fault .in time 检查错误操作的显
示盘,及时纠正
2 BOP control device alarm
4 position alarms : accumulator low pressure , air source low Check accumulator pressure Every well .每口井
pressure , oil tank low liquid level ,electrical pump running . setting .检查储能器压力设置
Check air source pressure setting Every well .每口井
检查气源压力设置
Check all parts fasten 检查所有 Daily 每日
部件紧固情况
Check and adjust setting 检查和 Daily 每日
39
GW19—ZJ30DT—PMS
调节设置
3 M / T instrument alarm 马丁仪表报警
11 alarm position : mud liquid level , flowmeter , hook load , rotary Check setting 检查设置 Every well 每口井
table torque , standpipe pressure , well depth , rotary table speed , Check sensor fasten 检查传感器 Weekly 每周
pump stroke , discharge capacity , mud input/output temperature , 紧固情况
fuel liquid level .11 个报警位置,液面传感器,流量计,大钩载 visual overall check 肉眼检查 Weekly 每周
荷,转盘钮矩,立管压力,井深,排量,泥浆入出口温度。 Check seal 检查密封 Weekly 每周
40