Professional Documents
Culture Documents
KPN en Tcd210155ac 20230810 Manual W
KPN en Tcd210155ac 20230810 Manual W
01. Fail-safe device must be installed when using the unit with machinery that
Bar Graph
may cause serious injury or substantial economic loss.(e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Temperature Controllers
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
high humidity, direct sunlight, radiant heat, vibration, impact or salinity
may be present.
Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel to use.
Failure to follow this instruction may result in electric shock.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire or electric shock.
05. Check ‘Connections’ before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.
01. When connecting the power input and relay output, use AWG 20 (0.50 mm2)
cable or over, and tighten the terminal screw with a tightening torque of 0.74
to 0.90 N·m.
When connecting the sensor input and communication cable without
dedicated cable, use AWG 27 to 16 cable and tighten the terminal screw with
a tightening torque of 0.74 to 0.90 N m..
Failure to follow this instruction may result in fire or malfunction due to contact
failure.
02. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage
03. Use a dry cloth to clean the unit, and do not use water or organic solvent.
KPN Series
Failure to follow this instruction may result in fire or electric shock.
04. Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
PRODUCT MANUAL Failure to follow this instruction may result in fire or product damage.
ᜢ ᜫ
-|Transparent Guide|-
• Do not apply excessive power when connecting or disconnecting the connectors of the
product.
Specifications
• Install a power switch or circuit breaker in the easily accessible place for supplying or
Series KPN Series
disconnecting the power.
Power supply 100 - 240 VACᜠ 50/60 Hz
• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature
Permissible voltage
controller. 90 to 110 % of rated voltage
range
• When changing the input sensor, turn off the power first before changing. After changing Power consumption ≤ 15 VA
the input sensor, modify the value of the corresponding parameter. Sampling period 50 ms
• Power supply should be insulated and limited voltage/current or Class 2, SELV power Input specification Refer to 'Input Type and Using Range'.
supply device. CT input • 0.0-50.0 A (primary current measurement range) • CT ratio: 1/1,000
• Do not overlapping communication line and power line. Use twisted pair wire for Option Remote SV 1 - 5 VDCᜡ or 4 - 20 mA (Current Input: External resistance 250 Ω)
communication line and connect ferrite bead at each end of line to reduce the effect of input • Contact - ON: ≤ 2 kΩ, OFF: ≥ 90 kΩ
Digital input
external noise. • Non contact - residual voltage ≤ 1.0 V, leakage current ≤ 0.1 mA
• Make a required space around the unit for radiation of heat. For accurate temperature Relay 250 VACᜠ 5 A 1a
Control
measurement, warm up the unit over 20 min after turning on the power. SSR 11 VDCᜡ±2 V, ≤ 20 mA
output
• Make sure that power supply voltage reaches to the rated voltage within 2 sec after Current DC 4-20 mA or DC 0-20 mA (parameter), load resistance: ≤ 500 Ω
supplying power. Alarm
Relay 250 VACᜠ 3 A 1a
• Do not wire to terminals which are not used. output
• This unit may be used in the following environments. DC 4 - 20 mA (load resistance: ≤ 500 Ω,
Option Transmission
output accuracy: ±0.3% F.S. ±1-digit)
- Indoors (in the environment condition rated in ‘Specifications’) output
RS485 Comm. Modbus RTU
- Altitude Max. 2,000 m
Display type 7 segment (red, green), control output bar graph (red, green), LED type
- Pollution degree 2
Heating,
- Installation category II
Control Cooling
ON/OFF, P, PI, PD, PID Control
type Heating &
Cooling
Ordering Information • Thermocouple, RTD: 1 to 100 (0.1 to 100.0) ℃/℉
Hysteresis
• Analog: 1 to 100 digit
This is only for reference, the actual product does not support all combinations.
Proportional band (P) 0.1 to 999.9 ℃/℉ (0.1 to 999.9%)
For selecting the specified model, follow the Autonics website . Integral time (I) 0 to 9,999 sec
Derivative time (D) 0 to 9,999 sec
K P N 5 ❶ ❷ - ❸ ❹ ❺ • 0.1 to 120.0 sec [relay output model]
Control cycle (T)
• 1.0 to 120.0 sec [SSR drive output model]
❶ Size ❸ Option Communication Manual reset 0.0 to 100.0%
2: DIN W 96 × H 48 mm output Relay Mechanical ≥ 10,000,000 operations
3: DIN W 48 × H 96 mm 0: No life
cycle Electrical ≥ 100,000 operations (load resistance: 250 VACᜠ 3 A)
5: DIN W 96 × H 96 mm 2: RS485
Between the charging part and the case: 3,000 VAC ~ 50/60 Hz for 1
Dielectric strength
❷ Control output ❹ Option in/output minute
0: No 0.75 mm amplitude at frequency of 5 to 55 Hz in each X, Y, Z direction
Output Type Vibration
PN 3: Transmission output + for 2 hours
number Heating: OUT1 Cooling: OUT2
Remote SV Insulation resistance ≥ 100 MΩ (500 VDCᜡ megger)
1 (Heating or Relay, selectable current or SSR drive
00 ±2 kV square shaped noise (pulse width 1 ㎲) by noise simulator
Cooling) output Noise immunity
❺ Power supply R-phase, S-phase
11 Selectable current or SSR drive output
Selectable current 0: 100-240 VACᜠ Memory retention ≈ 10 years (non-volatile semiconductor memory type)
13 2 (Heating & or SSR drive output Relay
Ambient temperature -10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)
Cooling)
Selectable current Ambient humidity 35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)
17 Relay
or SSR drive output
Protection structure IP65 (front panel, IEC standards)
19 Relay
Double or reinforced insulation (mark: ▱, dielectric strength between
Insulation type
the measuring input part and the power part: 2 kV)
Certification ᜢᜫ
Product Components • KPN52□-□: ≈ 160 g (≈ 230 g) • KPN53□-□: ≈ 160 g (≈ 230 g)
Unit weight
• Product (+ bracket) • Instruction manual (packaged) • KPN55□-□: ≈ 220 g (≈ 316 g)
Dimensions Connections
• Unit: mm, For the detailed drawings, follow the Autonics website. • Shaded terminals are standard model. is option specification.
• Below is based on KPN52□-□ Series.
J
250VAC 3A 1a
Digital
I RESISTIVE LOAD
DI-1
Input
4 16
F
B
H
AL2 OUT Relay Non contact,
Control
250VAC 3A 1a Circuit contact Input
DI-2
RESISTIVE LOAD 5 17
AL3 OUT Relay
Body Panel cut-out 250VAC 3A 1a
A B C D E F G H I J RESISTIVE LOAD 6 18 Analog Output
Output mA
DC4-20mA
KPN52□-□ 96 48 6 64.5 1.5 44.7 ≥ 115 ≥ 65 92+00.8 45+00.6 OUT1 Relay Circuit (Transmission output)/
250VAC 5A 1a 7 19 24VDC(LPS)
KPN53□-□ 48 96 6 64.5 1.5 91.5 ≥ 65 ≥ 115 45+00.6 92+00.8 RESISTIVE LOAD
KPN55□-□ 96 96 6 64.5 1.5 91.5 ≥ 115 ≥ 115 92 +0.8
0 92 +0.8
0 Current SSR 8 20 Current
DC0/4-20mA 11VDC±2V CT Transformer
ADC
■ Bracket
Load 500ΩMax. 20mA Max. Output
0.0-50.0A
9 Circuit 21
mA V
A
3.3
10 22 Analog
0-100mV
B
46 11 23 0-5V
4
mA
SOURCE ADC
1-5V
100-240VAC, Power V
Circuit B' 0-10V
50/60 Hz 12 24 0-20mA
37.5
40.5
RTD TC 4-20mA
KPN5□-□10 Sensor
12
23.9 7 OUT2 Relay
mA V 250VAC 5A 1a
RESISTIVE LOAD
Current SSR 8
Installation Method
DC0/4-20mA 11VDC±2V
Load 500ΩMax. 20mA Max.
9 OUT1 Relay
mA V 250VAC 5A 1a
10 RESISTIVE LOAD
Flathead screwdriver
Insert the unit into a panel, fasten the bracket by pushing with tools with a flathead
≥3.0
screwdriver. ≥3.0
≤5.8
≤5.8
Sensor error, MV
SSR
(Output ErMV 00)0
number: 2) Control stop, MV
OUT1 current output
StMV 00)0
Control stop, alarm
range output
O!MA 4-20 StAL CONT
OUT2 control output User level
selection
OUT2 SSR USER STND
SV setting lock
OUT2 current output
LcSV OFF
range
O@MA 4-20 Parameter 1 group lock LcP1 OFF
Parameter 2 group lock
Heating control cycle
LcP2 OFF
Parameter 3 group lock
02)0
(Relay)
H-T LcP3 OFF
Parameter 4 group lock
Cooling control cycle
00)0 LcP4 OFF
(SSR) Parameter 5 group lock
C-T
LcPS OFF
Password setting PWD 0000
-|Transparent Guide|- -
91.5
91.5
3 L
DOWN
3 L 3 L 3 L
86
86
UP
4 4 M M 4 4 M M 4 4 M M 4 4 M M
5 5 N N 5 5 N N 5 5 N N 5 5 N N
DOWN DOWN 6 6 O O 6 6 O O 6 6 O O 6 6 O O
7 7 P P 7 7 P P 7 7 P P 7 7 P P
8 Q 8 Q 8 Q 8 Q
13
13
8 Q 8 Q 8 Q 8 Q
9 9 R R 9 9 R R 9 9 R R 9 9 R R
A S A S A S A S
Sold Separately: Current Transformer (CT)
A S A S A S A S
B B T T B B T T B B T T B B T T
C U C U C U C U
• Unit: mm
C U C U C U C U
• The current for above CTs is 50A same but inner hole sizes are different. Please use this D D V V D D V V D D V V D D V V
for your environment. E W E E W W E W E W
• Do not supply primary current in case that CT output is open. High voltage will be
E W E W E W
F X F X F X F X
generated in CT output.
F X F X F X F X
G G Y Y G G Y Y G Y G Y
CSTC-E80LN
G Y G Y
H H Z Z H H Z Z H H Z Z H H Z Z
Ø23.3 F=50Hz
Ø7
10
3 Ta=25℃
100Ω
K(Black)
OUTPUT IN VOLTS RMS(V)
1 10Ω
7
L(White)
3.8
0.01
• Max. load current: 80A (50/60Hz)
• Current ratio: 1/1000 0.001
• Wire wounded resistance: 31Ω±10% 0.1 1 10 100 1000
SENSED CURRENT IN AMPS RMS(Io)
CSTC-E200LN
Ø37.1 F=50Hz
10
Ø13 3 Ta=25℃ 100Ω
10Ω
K(Black)
OUTPUT IN VOLTS RMS(V)
1
10
L(White)
4.5
0.1
40.8 150
0.01
13.5
CSTS-E80PP
21.4 F=50Hz
15.4 2.9 10 Ta=25℃ 100Ω
0.5
10Ω
Ø6
OUTPUT IN VOLTS RMS(V)
1
7
25.4
0.1
2.7
10.5
40.2
31 0.01
Ø3.4
0.001
10