Professional Documents
Culture Documents
Inbound 834247990563416673
Inbound 834247990563416673
Scope -This Japanese Industrial Standard specifies the hot rolled stainless steel strip (hereafter referred
to as “strip”).
2 Normative references The standards given in the Attached Tablè 1 contain pro-dard. The most recent
editions (including amendment) of the standards shall be applied.
3 Grade and symbols Plates and strip shall be classified into 63 grades, and their symbols and
classification shall be as given in Table 1.
Symbol of
Classification Symbol of grade Classification Symbol of grade Classification
grade
series
SUS315J1 SUS329J3L SUS420J2
-1590-
SUS315J2 SUS329J4L SUS429J1
hardening series
SUS316N SUS631
SUS316LN
Remarks 1 In the case where it is required to indicate by a symbol that the prod-uct is a plate, -HP shall
be suffixed to the symbol of the grade.
Example: SUS304-HP
G 4304-
2 In the case where it is required to indicate by a symbol that the prod.uct is a strip, -HS
shall be suffixed to the symbol of the grade.
Example: SUS304-HS
4 Chemical composition
4.1 Ladle analysis value The plates and strip shall be subjected to the ladle analysis test of 11.1,and the analysis test
value shall be as given in Tables 2 to 6.
4.2 Product analysis value When the product analysis value of plates and strip are required by the purchaser, the
product analysis test of 11.1 shall be carried out and the values of permissible variation shall be as given in Table 4 of
JIS G 0321However, the values of the elements and chemical composition not specified in this Table shall be as
agreed upon between the manufacturer and the purchaser.
-1590-
Symbol C Si Mn P S Ni Cr Mo Cu N Others
of grade
SUS301 0.15 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 6.00 to 8.00 16.00 to 18.00 -
SUS301L 0.030 max. 1.00 max. 2.00 max 0.045 max. 0.030 max. 6.00 to 8.00 16.00 to 18.00 - 0.20 max. 一
SUS301J1 0.08 to 0.12 1.00 max. 2.00 max. 0.045 max. 0.030 max. 7.00 to 9.00 16.00 to 18.00 - - 一 一
SUS302 0.15 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 8.00 to 10.00 17.00 to 19.00 一 - 一 -
SUS302B 0.15 max. 2.00 to 3.00 2.00 max. 0.045 max. 0.030 max. 8.00 to 10.00 17.00 to 19.00 - - - -
SUS303 0.15 max. 1.00 max. 2.00 max. 0.20 max. 0.15.min. 8.00 to 10.00 17.00 to 19.00 (1) - 一 -
SUS304 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 8.00 to 10.50 18.00 to 20.00 - - 一 一
SUS304L 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 9.00 to 13.00 18.00 to 20.00 一 - 一
SUS304N1 0.08 max. 1.00 max. 2.50 max. 0.045 max. 0.030 max. 7.00 to 10.50 18.00 to 20.00 - - 0.10 to 0.25 一
SUS304N2 0.08 max. 1.00max 2.50 max. 0.045 max. 0.030 max. 7.50 to 10.50 18.00 to 20.00 - - 0.15 to 0.30 Nb 0.15 max.
SUS304LN 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 8.50 to 11.50 17.00 to 19.00 一 - 0.12 to 0.22
SUS304J1 0.08 max. 1.70 max. 3.00 max. 0.045 max. 0.030 max. 6.00 to 9.00 15.00 to 18.00 - 1.00 to 3.00 一
SUS304J2 0.08 max. 1.70 max. 3.00 to 5.00 0.045 max. 0.030 max. 6.00 to 9.00 15.00 to 18.00 一 1.00 to 3.00 一
SUS305 0.12 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 10.50 to 13.00 17.00 to 19.00 - - - --
SUS309S 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 12.00 to 15.00 22.00 to 24.00 一 - 一 一
SUS310S 0.08 max. 1.50 max. 2.00 max. 0.045 max. 0.030 max. 19.00 to 22.00 24.00 to 26.00 一 一 - 一
SUS315J1 0.08 max. 0.50 to 2.50 2.00 max. 0.045 max. 0.030 max. 8.50 to 11.50 17.00 to 20.50 0.50 to 1.50 0.50 to 3.50 一 一
SUS315J2 0.08 max. 2.50 to 4.00 2.00 max. 0.045 max. 0.030 max. 11.00 to 14.00 17.00 to 20.50 0.50 to 1.50 0.50 to 3.50 - 一
SUS316 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 10.00 to 14.00 16.00 to 18.00 2.00 to 3.00 - - 一
SUS316L 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 12.00 to 15.00 16.00 to 18.00 2.00 to 3.00 一 - -
SUS316N 0.08 max.. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 10.00 to 14.00 16.00 to 18.00 2.00 to 3.00 - 0.10 to 0.22 一
SUS316LN 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 10.50 to 14.50 16.50 to 18.50 2.00 to 3.00 - 0.12 to 0.22 -
SUS316Ti 0:08 max. 1.00max. 2.00 max. 0.045 max. 0.030 max: 10.00 to 14.00 16.00 to 18.00 2.00 to 3.00 一 - Ti 5xC%min.
SUS816J1 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 10.00 to 14.00 17.00 to 19.00 1.20 to 2.75 1.00 to 2.50 -
-4304-
SUS316J1L 0.030 max. 1.00max. 2.00 max. 0.045 max. 0.030 max. 12.00 to 16.00 17.00 to 19.00 1.20 to 2.75 1.00 to 2.50 一
01
Symbol C Si Mn P S Ni Cr Mo Cu N Others
of grade
SUS317 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 11.00 to 15.00 18.00 to 20.00 3.00 to 4.00 一 一 一
SUS317L 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030max. 11.00 to 15.00 18.00 to 20.00 3.00 to 4.00 - 一 -
SUS317LN 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 11.00 to 15.00 18.00 to 20.00 3.00 to 4.00 - 0.10 to 0.22 一
SUS317J1 0.040 max. 1.00 max. 2.50 max. 0.045 max. 0.030 max. 15.00 to 17.00 16.00 to 19.00 4.00 to 6.00 - 一 -
SUS317J2 0.06 max. 1.50 max. 2.00 max. 0.045 max. 0.030 max. 12.00 to 16.00 23.00 to 26.00 0.50 to 1.20 - 0.25 to 0.40 -
SUS317J3L 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 11.00 to 13.00 20.50 to 22.50 2.00 to 3.00 - 0.18 to 0.30 -
SUS836L 0.030 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 24.00 to 26.00 19.00 to 24.00 5.00 to 7.00 - 0.25 max. -
SUS890L· 0.020 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 23.00 to 28.00 19.00 to 23.00 4.00 to 5.00 1.00 to 2.00 一 -
SUS321 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 9.00 to 13.00 17.00 to 19.00 一 - - Ti 5xC% min.
SUS347 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 9.00 to 13.00 17.00 to 19.00 一 - - Nb 10xC% min.
SUSXM7 0.08 max. 1.00 max. 2.00 max. 0.045 max. 0.030 max. 8.50 to 10.50 17.00 to 19.00 - 3.00 to 4.00 - -
-1592- -
SUSXM15J1 0.08 max. 3.00 to 5.00 2.00 max. 0.045 max. 0.030 max. 11.50 to 15.00 15.00 to 20.00 - 一 -
Remarks: Alloying elements other than those given in Table 2 may be added to SUSXM15J1, if required.
Unit:%
Symbol C Si Mn P S Ni Mo
Cr N
of grade
SUS329J1 0.08 max. 1.00 max. 1.50 max. 0.040 max. 0.030 max. 3.00 to 6.00 23.00 to 28.00 1.00 to 3.00
SUS329J3L
0.08 to 0.20
0.030 max. 1.00 max. 2.00 max. 0.040 max. 0.030 max. 4.50 to 6.50. 21.00 to 24.00 2.50 to 3.50
Remarks: Alloying elements other than those given in Table 3 may be added, if required.
Symbol C Si P S Cr
Mn Mo N Others
of grade
SUS405 0.08 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 11.50 to 14.50 - - A1 0.10 to 0.30
SUS410L 0.030 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 11.00 to 13.50 - 一 一
SUS429 0.12 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 14.00 to 16.00 - - -
SUS430 0.12 max. 0.75 max. 1.00max. 0.040 max. 0.030 max. 16.00 to 18.00 - ·- -
SUS430LX 0.030 max. 0.75 max: 1.00 max. 0.040 max. 0.030 max. 16.00 to 19.00 - 一 Ti or Nb 0.10 to 1.00
SUS430J1L 0.025 max. 1.00 max.. 1.00 max. 0.040 max. 0.030 max. 16.00 to 20.00 - 0.025 max. Ti, Nb, Zr or their combination
C%+N%)to 0.80,
Cu 0.30 to 0.80
SUS434 0.12 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 16.00 to 18.00 0.75 to 1.25 - 一
SUS436L 0.025 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 16.00 to 19.00 0.75 to 1.50 0.025 max. Ti,Nb,Zr or their combination
SUS436J1L 0.025 max. 1.00 max. 1.00max. 0.040 max. 0.030 max. 17.00 to 20.00 0.40 to 0.80 0.025 max. Ti, Nb, Zr or their combination
SUS444 0.025 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 17.00 to 20.00 1.75 to 2.50 0.025 max. Ti,Nb, Zr or their combination
3 x(C%+N%) to 0.80
SUS445J1 0.025 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 21.00 to 24.00 0.70 to 1.50 0.025 max.
SUS445J2 0.025 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 21.00 to 24.00 1.50 to 2.50 0.025 max. -
SUS447J1 0.010 max. 0.40 max. 0.40 max. 0.030 max. 0.020 max. 28.50 to 32.00 1.50 to 2.50 0.015 max. -
SUSXM27 0.010 max. 0.40 max. 0.40 max. 0.030 max. 0.020 max. 25.00 to 27.50 0.75 to 1.50 0.015 max.
Remarks 1 The grades other than SUS447J1.and SUSXM27 may contain 0.60 % max. of Ni.
-G 4304-
2 SUS447J1 and SUSXM27 may contain 0.50 % max. of Ni, 0.20% max. of Cu and 0.50 % max. of (Ni+Cu).In addition, alloying elements
-1593- other than those given in Table 4 may be added to SUS447J1, SUSXM27,SUS445J1, SUS445J2 and SUS430J1L, if required.
Unit:%
Symbol C Mn P S
Si Cr
of grade
SUS403 0.15 max. 0.05 max. 1.00 max. 0.040 max. 0.030 max. 11.50 to 13.00
SUS410 0.15 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 11.50 to 13.50
1.00 max. 1.00 max. 0.040 max. 0.030 max. 11.50 to 13.50
SUS410S 0.08 max.
12.00 to 14.00
0.26 to 0.40 1.00 max. 1.00 max. 0.040 max. 0.030 max.
SUS420J2
15.00 to 17.00
0.25 to 0.40 1.00 max. 1.00 max. 0.040 max. 0.030 max.
SUS429J1
16.00 to 18.00
0.60 to 0.75 1.00 max. 1.00 max. 0.040 max. 0.030 max.:
-1594- SUS440A
Unit:%
Symbol Mn
C Si P S Ni Cr Cu Others
of grade:
SUS630 0.07 max. 1.00 max. 1.00 max. 0.040 max. 0.030 max. 3.00 to 5.00 15.00 to 17.50 3.00 to 5.00 Nb 0.15 to 0.45
-
SUS631 0.09 max. 1.00max. 1.00 max. 0.040 max. 0.030 max. 6.50 to 7.75 16.00 to 18.00 A1 0.75 to 1.50
-G 4304-
be subjected to the test of 11.2, and the mechanical properties shalI be as follows.tween the manufacturer and the
purchaser.
SUS301
205 min. 520 min. 40 min. 207 max. 95 max. 218 max.
2.0
SUS301L 215 min. 550 min. 45 min. 207 max. 95 max. 218 max.
SUS301J1 205 min. 570 min. 45 min. 187 max. 90 max. 200 max.
SUS302 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS302B 205 min. 520 min. 40 min. 207 max. 95 max. 218 max.
SUS303 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS304 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS304L 175 min. 480 min. 40 min. 187 max. 90 max. 200 max.
SUS304N1 275 min. 550 min. 35 min. 217 max. 95 max. 220 max.
SUS304N2 345 min. 690 min. 35 min. 248 max. 100 max. 260 max.
SUS304LN 245 min. 550 min. 40 min. 217 max. 95 max. 220 max.
SUS304J1 155 min. 450 min. 40 min. 187 max. 90 max. 200 max.
SUS304J2 155 min. 450 min. 40 min. 187 max. 90 max. 200 max.
SUS305 175 min. 480 min. 40 min. 187 max. 90 max. 200 max.
SUS309S 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS310S 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
:.
SUS315J1 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS315J2 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS316 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS316L 175 min. 480 min. 40 min. 187 max. 90 max. 200 max.
--
SUS316N 275 min. 550 min. 35 min. 217 max. 95 max. 220 max.
SUS316LN 245 min. 550 min. 40 min. 217 max. 95 max. 220 max.
SUS316Ti 205 min. 520 min. 40 min. 187 max. 90 max. 200max.
SUS316J1 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS316J1L 175 min. 480 min. 40 min. 187 max. 90 max. 200 max.
Table 7(concluded)
-1596-
-G 4304-
grade
N/m㎡2 N/mm2 % HB HRB HV
SUS317 205 min. 520 min. 40 min. 187 max.. 90 max. 200 max
SUS317L 175 min. 480 min. 40 min. 187 max. 90 max. 200 max.
:3
SUS317LN 245 min. 550 min. 40 min. 217 max. 95 max. 220 max.
SUS317J1 175 min. 480 min. 40 min. 187 max. 90 max. 200 max.
SUS317J2 345 min. 690 min. 40 min. 250 max. 100 max. 260 max.
SUS317J3L 275 min. 640 min. 40 min. 217 max. 96 max. 230 max.
SUS836L 275 min. 640 min. 40 min. 217 max. 96 max. 230 max
SUS890L 215 min. 490 min. 35 min. 187 max. 90 max. 200 max.
SUS321 205 min. 520 min. 40 min. 187 max. 90 max. 200 max.
SUS347 205 min. 520 min. 40 min. 187 max. 90 max. 200 max
SUSXM7 155 min. 450 min. 40 min. 187 max. 90 max. 200 max.
SUSXM15J1 205 min. 520 min. 40 min. 207 max. 95 max. 218 max.
5.2 Mechanical properties of austenite-ferritic series The proof stress,ten-sile strength, elongation and hardness of
the plates and strip processed by solution treatment shall be as given in Table 8. However, the proof stress shall be
applied only when particularly designated by the purchaser.
Symbol of Hardness
Proof streSS Tensile strength Elongation
grade
N/mm2 N/m㎡2 % HB HRC HV
SUS329J1 390 min. 590 min. 18 min. 277 max. 29 max. 292 max.
SUS329J3L 450 min. 620 min. 18 min. 302 max. 32 max. 320 max.
SUS329J4L
-G 4304-
450 min. 620 min. 18 min. 302 max. 32 max. 320 max.
5.3 Mechanical properties of ferritic series The proof stress, tensile strength,elongation, hardness and
bendability of the plates and strip annealed shall be as given in Table 9. However, the proof stress shall be
applied only when particularly designated by the purchaser. As regards the bendability,any crack shall not be
generated on the outside of the bent corner.
HB HRB HV
Bending
N/m㎡2 N/mm2 % Inside radius
angle
SUS405 175 min. 410 min. 20 min. 183 max. 88 max. 200 max. 180° 0.5 times the thickness for
under 8 mm in thickness
-1597-
-G 4304-
8 mm min.in thickness
SUS410L 195 min. 360 min. 22 min. 183 max. 88 max. 200 max. 180° 1.0 times the thickness
SUS429 205 min. 450 min. 22 min. 183 max. 88 max. 200 max. 180° 1.0 times the thickness
SUS430 205 min. 450 min. 22 min. 183 max. 88 max. 200 max. 180° 1.0 times the thickness
SUS430LX 175 min. 360 min. 22 min. 183 max. 88 max. 200 max. 180° 1.0 times the thickness
SUS430J1L 205 min. 390 min. 22 min. 192 max. 90 max. 200 max. 180° 1.0 times the thickness
SUS434 205 min. 450 min. 22 min. 183 max. 88 max. 200 max. 180° 1.0 times the thickness
SUS436L 245 min. 410 min. 20 min. 217 max. 96 max. 230 max. 180° 1.0 times the thickness
SUS436J1L 245 min. 410 min. 20 min. 192 max. 90 max. 200 max. 180° 1.0 times the thickness
SUS444 245 min. 410 min. 20 min. 217 max. 96 max. 230 max. 180° 1.0 times the thickness
SUS445J1 245 min. 410 min. 20 min. 217 max. 96 max. 230 max. 180° 1.0 times the thickness
SUS445J2 245 min. 410 min. 20 min. 217 max. 96 max. 230 max. 180° 1.0 times the thickess
SUS447J1 295 min. 450 min. 22 min. 207 max. 95 max. 220 max. 180° 1.0 times the thickness
SUSXM27
245 min. 410 min. 22 min. 192 max. 90 max. 200 max. 180° 1.0 times the thickness
5.4 Mechanical properties of martensitic series Mechanical properties of mar-tensitic series shall be as follows.
5.4.1 The proof stress, tensile strength, elongation, hardness and bendability of the plates and strip which have been
annealed shall be as given in Table 10. However,the proof stress shall be applied only when particularly designated by
the purchaser.As regards the bendability, any crack shall not be generated on the outside of the bent corner. -G 4304-
5.4.2 The hardness of the plates and strip which have been processed by quench hardening and tempering shall be as
given in Table 11.
(martensitic series)
SUS403 205 min: 440 min. 20·min. 201 max. 93 max. 210 max. 180° 1.0 times the thickness
SUS410 205 min. 440 min. 20 min. 201 max. 93 max. 210 max. 180° 1.0 times the thickness
SUS410S 205 min. 410 min. 20 min. 183 max. 88 max. 200 max. 180° 1.0 times the thickness
SUS420J1 225 min. 520 min. 18min: 223 max. 97 max. 234 max. -
SUS420J2 225 min. 540 min. 18 min. 235 max. 99 max. 247 max. -
SUS429J1 225 min. 520 min. 18min. 241 max. 100 max. 253 max. - -
SUS440A 245 min. 590 min. 15 min. 255 max. HRC 25 max. 269 max. -
-1598-
-G 4304-
(martensitic series)
SUS420J2 40 min.
-G 4304-
SUS440A
5.5 Mechanical properties of precipitation hardening series The proof stress,tensile strength, elongation and
hardness of the plates and strip which have been processed by solution treatment and those of the test piece
processed by precipita-tion hardening by designation of the purchaser shall be as given in Table 12. How-ever, the
proof stress shall be applied only when particularly designated by the purchaser.
HBS (or H
treatment N/m㎡2 N/m㎡2
SUS630 S -J - 一 363 ma
H900 1 175 min. 1 310 min. 5.0 mm max. in thickness 5 min. 375 mi
H1075 860 min. 1 000 min. 5.0 mm max. in thickness 5 min. 302 min. 31 min. - -
10 min.
incl.15.0 mm in thickness
TH1050 960 min. 1 140 min. 3.0mm max. in thickness 3 min. - 35 min. - 345 min.
-G 4304-
6 Corrosion resistance In the case where the corrosion resistance by an inter granular corrosion test is particularly
designated by the purchaser,a-test method to be applied shall be selected from the test methods of 11.3 as agreed
upon between the manufacturer and the purchaser. The test is subjected thereto, and the corro-sion resistance
shall be as follows.
6.1 Discrimination by the etched structure obtained by 10% oxalic acid etching test shall be as given in
Table 13.
Pitting structure II
SUS316L
一
SUS316J1L
SUS317L
SUS321
SUS347
6.2 The corrosion rate by the ferric sulfate-sulfuric acid corrosion test shall be as given in Table 14.
Symbol
SUS317L
-G 4304-
6.3. The corrosion rate by the 65 % nitric acid corrosion test shal be as given in
Table 15 Corrosion rate by 65 % nitric acid corrosion test
Symbol
(solution treatment)
between the manufacturer
6.4 The condition of the bent surface by the copper sulfate sulfuric acid corrosion test shall be as given in Table 16.
-1601-
Symbol
SUS316J1
SUS317
SUS316J1L
SUS317L
SUS321
SUS347
7 Surface finish The surface finish of plates and strip shall be as given in Table 17.
-G 4304-
Symbol of
Summary
surface finish
Remarks: Surface finishes other than those given in Table 17 may be agreed upon between the manufacturer
and the purchaser.
8.1.1 Standard dimensions of plates The standard dimensions of plates shall be as given in Table 18.
-1602-
Unit:mm
Thickness xlength
7.0 15.0
chaser.
8.1.2 Standard thicknesses of strip The standard thicknesses of strip shall be as given in Table 19.
chaser.
8.2 Mass of plates The mass of plates shall be as a rule in accordance with JIS G 4310.
8.3-Tolerances on thickness of plates The tolerances on the thickness of plates shall be as follows.
8.3.1The tolerances (symbol A) on thickness shall be as given in Table 20. How-ever,the purchaser may
designate the tolerances (symbol B) on the thickness given in Table 21.
The measuring position for thickness shall be at an arbitrary point 15 mm or over from the plate edge for the plate of
a cut edge. However, in the case of the plate of a mill edge, it shall be at an arbitrary point 25 mm or over from the plate
edge for a cut plate from the strip, and at an arbitrary point inside the planned cutting line of width for other plates.
Unit:mm
Tbickness Width
-1603-
-G 4304-
4.00 or over to and excl. 5.00 ±0.40 ±0.45 ±0.50 ±0.60 ±0.80 ±1.0 -
5.00 or over to and excl. 6.00 ±0.50 ±0.55 ±0.60 ±0.70 ±0.90 ±1.1 -
6.00 or over to and excl. 8.00 ±0.60 ±0.65 ±0.70 ±0.75 ±1.0 ±1.2 ±1.4
8.00 or over to and excl. 10.0 ±0.65 ±0.65 ±0.65 ±0.80 ±1.2 ±1.5 ±1.6
10.0 or over to and excl. 16.0 ±0.70 ±0.70 ±0.70 ±0.85 ±1.2 ±1.5 ±1.6
"16.0 or over to and excl. 25.0 ±0.80 ±0.80 ±0.80 ±0.95 ±1.3 ±1.5 ±1.6
25.0 or over to and excl. 40.0 ±0.90 ±0.90 ±0.90 ±1.1 ±1.3 ±1.5 ±1.6
40.0 or over to and excl. 63.0 ±1.0 ±1.0 ±1.2 ±1.2 ±1.4 ±1.5 ±1.6
63.0 or over to and excl. 100 ±1.1 ±1.2 ±1.3 ±1.3 ±1.5 ±1.6 ±1.7
100 or over to and excl. 160 ±1.3 ±1.3 ±1.4 ±1.4 ±1.6 ±1.7 ±1.8
-G 4304-
160 or over to and excl 200 ±1.6 ±1.6 ±1.7 ±1.7 ±1.9 ±2.0 ±2.1
Thickness Width
and excl
and excl. and excl. and excl. and excl. and
3 150
excl
1250 1 600 2000 2500
4000
-1604-
-G 4304-
0701090.3
010
010
10
-G 4304-
0N0 30
-G:4304-
Unit:mm
Thickness
Width
and excl. and excl. and excl. and excl. and excl. and excl.
1 250 1.600 2500 3150 4000
2000
4.00 or over to and excl. 5.00 0.13 0.15. 0.20 0.35 0.55 0.75 一
5.00 or over to and excl.6.00 0.20 0.20 0.25 0.45 0.65 0.85 -
6.00 or over to and excl. 8.00 0.30 0.35 0.35 0.50 0.75 0.95 1.15
8.00 or over to and excl. 10.0 0.40 0.40 0.40 0.55 0.95 1.25 1.35
10.0 or over to and excl. 16.0 0.45 0.45 0.45 0.60 0.95 1.25 1.35
16.0. or over to and excl. 25.0 0.55 0.55 0.55 0.70 1.05 1.25 1.35
25.0 or over to and excl. 40.0 0.65 0.65 0.65 0.85 1.05 1.25 1.35
40.0 or over to and excl. 63.0 0.75 0.75 0.95 0.95 1.15 1.25 1.35
63.0 or over to and excl. 100 0.85 0.95 1.05 1.05 1.25 1.35 1.45
100 or over to and excl. 160 1.05 1.05 1.15 1.15 1.35 1.45 1.55
160or over to and excl. 200 1.35 0.35 1.45 1.45 1.65 1.75 1.85
Remarks: For tolerances other than those given in Table 20 and Table 21,a value
8.4 Tolerances on width of plates The tolerance on width of plates shall be as given in Table 23 for the cut edge
plates and in Table 24 for the mill edge plates.
Table 23 Tolerances on width of cut edge plates
Unit:mm
Classification
Width Under 2 000 2 000 or over
method up to and
up to and
Under 10.0 0 0
mechanic 0. 0 0 0
al
10.0 or over to and
cutting
0 0
excl.20.0 0 0 0 0
0 0 0 0
incl.28.0 0 0
flame excl.100
excl.200
-1605-
Under 100 ±1
+not specified
+not specified
1 000 or over 0
0
8.5 Tolerances on length of plates The tolerances on length of plates shall be as given in Table 25.
Table 25 Tolerances on length of plates
Unit:-mm
Classification Over 3 500 up to Over 6 000
0 0
mechanical
0 0 0 0
excl.20.0 0 0 0
0 0 0
20.0 or over up to
0
and incl.28.0 0 0 0 0
flame excl.100
excl.200
Remarks:The tolerance on length of plates by flame cutting, if the length is and the purchaser.
The flame cutting refers to the cutting by using powder, and other methods (mechanical
cutting, plasma cutting, laser cutting, water jet cutting,etc.) are included in the mechanical
cutting.
-1607-
-G 4304-
-G 4304-
8.6 Flatness of plates The maximum value of flatness of plates shall be as given in Table 26.
-G 4304-
Length
of flatness flatness(symbol EF)
Over 2 000 6
20
Over 2 000 6
20
-
Over 2 000 35
Remarks 1 Table 26 applies to an arbitrary length of 3 500 mm,and in the case of under 3 500 mm length, it
applies to overall length.
2 Table 26 applies to cut plates from mill edge strip and to cut edge plates.
8.7 Tolerances on thickness of strip Tolerances on the thickness of a strip shall be as given in Table 27.
However, the purchaser may designate the tolerance (sym-bol ET) of thickness of Table 28.
Further, they do not apply to the abnormal parts of strip at the fore and rear parts.
The measuring positions for thickness shall be at an arbitrary point 25 mm or over from the edge for mill
edge strip of 50 mm or over in width and shall be its center for under 25 mm in width. In the case of cut edge
strip, the measuring posi-tion shall be at an arbitrary point 15 mm or over from the edge and shall be its
center for under 30 mm in width.
1 000 or over to
1 250 or over to
Under 1 000
and excl.1 250 and excl.1 600
-1606-
-1607-
-G 4304-
-G 4304-
Unit:mm
Thickness Width
250 over to
over to over to over to over to
over to
and excl. and excl. and excl. and excl. and excl.
and excl
400 630 800 1000 1 250
1 600
incl.8.00 - - 一
8.8 Tolerances on width of strip Tolerances on width of strip shall be as given in Table 29. However, in the case of cut
edge strip, the purchaser may designate the tolerances (symbol EW) on width of Table 30.
and excl. and excl. and excl. and excl. and excl.
-1608-
-G 4304-
+25 +30
Mill edge ±1 ±2 ±2 ±5
- 0
0 0
Under 6.00
0 0
0 0 0 0 0
6.00 or over
0 0 0 0 0 0 0
-G 4304-
8.9 Lateral warp of strip The maximum value of the lateral warp of a strip shall be as given in Table 31. However, this table does not
apply to the abnormal por-tions of strip at the fore and rear parts.
Unit:mm
9 Appearance The plates and strip shall be free from defects: detrimental to use.However, the strip has
generally no chance for removing defects, some abnormal parts may be contained.
10 Manufacturing method After hot rolling, plates are heat treated. After pickling or treatments equivalent thereto,
they are suitably levelled as required.
Treatment such as pickling or the like may be omitted as agreed upon between.the manufacturer and the purchaser. However, in
the case where plates are used.as materials for pipes and pipe fittings to be solution treated and as materials for rerolling, solution
treatment may be omitted as agreed upon between the manufac-lurer and the purchaser. 'In this case the symbol AR shall be suffixed.
Strips are used as hot rolled and otherwise, as required, they are processed by heat treatment, pickling,etc.
-1609-
-G 4304-
Treatment such as pickling or the like may be omitted as agreed upon between the manufacturer and the purchaser.
For heat treatments for platè and strips of precipitation hardening series, the purchaser designates the class of heat
treatment
11 Tests
JIS G 1211, JIS G 1212, JIS G 1213, JIS G 1214, JIS G 1215,
JIS G 1216, JIS G 1217, JIS G 1218, JIS G 1219, JIS G 1223,JIS G 1224, JIS G 1228, JIS G 1232, JIS
G 1237, JIS G 1253,JIS G 1256, JIS G 1257
11.2.1 General General items of mechanical tests shall be in accordance with 4of JIS G 0303.
11.2.2 Sampling of a test specimen One test specimen shall be sampled for each lot of the same ladle and the same heat
treatment conditions.
11.2.3 Number of test pieces One test piece shall be taken from each test specimen.
11.2.4 Test pieces The tensile test piece, hardness test piece, and bend test piece shall be as follows:
a)Any one of the No. 10 test piece, No. 13B test piece, No. 14A test piece and No.14B test piece specified in JIS Z 2201
shall be used as a tensile test piece.
Further, No. 4 test piece or No.5 test piece may also be used.
b) A part of the tensile test piece or bent test piece may be used as a hardness test piece.
c) The No.3 test piece or No.5 test piece specified in JIS Z 2204 shall be used as a bend test piece.
11.2.5 Test methods The methods for tensile test, hardness test and bend test shall be as follows:
a) The tensile test method shall be in accordance with JIS Z 2241. A test tem-perature of(23±5) °C shall be taken as a
standard and as to measurement of tensile strength other than that of martensitic series, a tensile speed wherein the
strain increasing rate at the parallel part of a test piece becomes 40 %/min to 80 %/min, shall be used.
-G 4304-
The hardness test method shall be in accordance with any of the following stan-dards. A test temperature of (23±5)°℃
shall be taken as a standard.
-1610-
11.3.1 Sampling of a test specimen One test specimen shall be sampled from each plate or strip of the same
ladle and the same heat treatment condition.
11.3.2 Number of test pieces One test piece shall be taken from each test speci-
11.3.3 Test methods The corrosion test method shall be in accordance with any of the following Standards.
13 Marking The plates and strip which have passed insection shall be marked with the following items on either of each
plate or each bundle for the plates and on each bundle for the strip. However, a part of the items may be'omitted as
agreed upon between the manufacturer and the purchaser.
a) Symbol of grade
b) Dimensions
c) Symbol of tolerance (When the tolerance symbols,B,ET,EW and EF apply,these shall be marked.)
d)Symbol of heat treatment (exclusively in the cases of omitting solution treat-ment, of solution treatment on rolling
line, and of quench hardening or temper-ing particularly designated by the purchaser for SUS402J2 and SUS440A of the
precipitation hardening series and martensitic series.)
-G 4304-
14 Report The manufacturer shall submit the report of the plates or strip to the purchaser in which the results of a test
specified or designated and, as required,dimension, quantity, delivery conditions, etc. are stated. It is also allowed to
send the report by any electrical transmission.
In the case where any alloying elements have been added in accordance with the Remarks of Tables 2 to 5,
contents of the added elements shall be detailed in the report.
JIS G 0321 Product analysis and its tolerance for wrought steel
JIS G 0571 Method of 10 per cent oxalic acid etch test for stainless steels
-1612-
JIS G 1211Iron and steel-Methods for determination of carbon content
JIS G 1213
JIS G 1223
JIS G 1228
JIS G 1253Iron and steel-Method for spark discharge atomic emission spectrometric analysis
JIS G 1256
analysis
-G 4304-
JIS G 4310Method of mass calculation for stainless steel plates and sheets,
JIS Z 2201
JIS Z 2241
JIS Z 2248
-1613-
Attached Table 2 Heat treatment symbol of precipitation
hardening series
Annex (informative)
Heat treatment
Introduction This Annex (informative) supplements items related to this Stan dard and is not a part of the
provisions.
Under the reason that heat treatment shall be executed at a temperature satisfy.ing the mechanical properties
specified in JIS and other specification items, and those temperature based on the technical knowledge of the
manufacturer should be accepted, temperatures of the heat treatment are eliminated from this Standard and stated
as informative values in the Annex.
SUS301 1 010 to 1 150 rapid cooling SUS316L 1 010 to 1 150 rapid cooling
SUS301L 1 010 to 1 150 rapid cooling SUS316N 1 010 to 1 150 rapid cooling
SUS301J1 1 010 to 1 150 rapid cooling SUS316LN 1 010 to 1 150 rapid cooling
SUS302 1 010 to 1 150 rapid cooling SUS316Ti 920 to 1 150 rapid cooling
-1614-
-G 4304-
SUS315J2 1 010 to 1 150 rapid cooling SUSXM7 1 010 to 1 150 rapid cooling
-G 4304-
Remarks 1 The purchaser may specify stabilizing heat treatment to SUS316Ti,SUS321 and SUS347.
austenite-ferritic series
-1615-
-G 4304-
SUS436J1L
SUS429 or slow cooling
800 to 1 050 rapid cooling
SUS430 780 to 850 rapid cooling SUS444
800 to 1 050 rapid cooling
or slow cooling
SUS430LX SUS445J1
780 to 850 rapid cooling 850 to 1 050 rapid cooling
SUS430J1L
SUS445J2
or slow cooling 850 to 1 050 rapid cooling
780 to 950 rapid cooling SUS447J1
900 to 1 050 rapid cooling
or slow cooling
SUSXM27
900 to 1050 rapid cooling -G 4304-
800 to 1 050 rapid cooling
00
SUS410S
800 to 900 slow cooling - -
SUS420J2
Approx.750 rapid cooling or 980 to 1 040 150 to 400
Remarks 1
-1616-
-G 4304-
2 The annealing may be replaced by the quench hardening and tempering which ensures
specified mechanical prop-erties.
Precipitation
H900 After (S) treatment, 470 °℃ to 490 °C air cooling
hardening
H1025 After (S) treatment, 540°℃ to 560°C air cooling
treatment
H1075 After (S) treatment, 570°℃ to 590 °C air cooling
Remarks: As regards SUS630, heat treatments other than those as given in Annex Table 5 may be agreed upon
between the manufacturer and the purchaser,
-1616-