Professional Documents
Culture Documents
LOCTITE 586 en - GL
LOCTITE 586 en - GL
LOCTITE® 586™
October -2004
ss
characteristics:
a
e
75
Br
Ste
Technology Acrylic
Chemical Type Dimethacrylate ester
ate
Appearance (uncured) Red liquid 50
rom
Fluorescence Positive under UV light
ich
l
tee
cd
Components One component -
ss
25
Zin
requires no mixing
les
ain
Viscosity Medium
St
Cure Anaerobic 0
Secondary Cure Activator 1min 5min 10min 30min 1h 3h 6h 24h 72h
Application Thread sealing Cure Time
m
75
5m
Flash Point - See SDS
0.0
m
Viscosity @ 25°C, mPa·s (cP):
5m
Falling ball "E" 4,000 to 6,000
0.1
50
mm
25
0.2
TYPICAL CURING PERFORMANCE
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 586™, October -2004
% of Full Strength on Steel 100 Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
M10 black oxide bolts and steel N·m 25 to 55
nuts (lb.in) (220 to 485)
75
Max. Prevail Torque, ISO 10964, Pre-torqued to 5 N·m:
40 °C
M10 black oxide bolts and steel N·m 30 to 55
C
nuts (lb.in) (265 to 485)
22 °
50
5 °C
Compressive Shear Strength, ISO 10123:
Steel pins and collars N/mm² 10 to 25
25 (psi) (1,450 to 3,625)
0
1min 5min 10min 30min 1h 3h 6h 24h 72h
Cure Time Torque Augmentation
Breakloose torque of an uncoated fastener will normally be 15
to 30% less than the on-torque. The effect of LOCTITE® 586™
Cure Speed vs. Activator
Where cure speed is unacceptably long, or large gaps are on the breakloose torque is shown in the graph below.
present, applying activator to the surface will improve cure 60
Activator SF 7649™
20 ITE® 58
LOCT
out
75 10 er with
Activator SF 7471™ fasten
M10
0
50 0 10 20 30 40 50
Seating torque (N·m)
25
TYPICAL ENVIRONMENTAL RESISTANCE
No activator Cured for 1 week @ 22 °C
0 Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
1min 5min 10min 30min 1h 3h 6h 24h 72h
M10 zinc phosphate steel nuts and bolts
Cure Time
Hot Strength
TYPICAL PROPERTIES OF CURED MATERIAL Tested at temperature
Physical Properties:
Coefficient of Thermal Expansion, 100×10-6
100
ISO 11359-2, K-1
Coefficient of Thermal Conductivity, ISO 8302, 0.1
% Strength @ 22 °C
W/(m·K)
75
Specific Heat, kJ/(kg·K) 0.3
50
After 24 hours @ 22 °C 0
Breakaway Torque, ISO 10964: 0 50 100 150
M10 black oxide bolts and steel N·m ≥15 Temperature, °C
nuts (lb.in) (≥160)
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 586™, October -2004
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
TDS LOCTITE® 586™, October -2004
Conversions Reference 2
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Disclaimer
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product. Any liability in respect of the
information in the Technical Data Sheet or any other written or oral
recommendation(s) regarding the concerned product is excluded, except if
otherwise explicitly agreed and except in relation to death or personal injury
caused by our negligence and any liability under any applicable mandatory
product liability law.
Trademark usage
Except as otherwise noted, all trademarks in this document are trademarks of
Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark registered
in the U.S. Patent and Trademark Office.
For the most direct access to local sales and technical support visit: www.henkel.com/industrial