2
BODY DIMENSIONS
BODY DIMENSIONS AND MEASUREMENT
METHODS .
TYPE A
(PROJECTED DIMENSIONS) ...
TYPE B
(ACTUAL-MEASUREMENT DIMENSIONS)
UNDER BODY .......
ENGINE COMPARTMENT
UPPER BODY .
SIDE BODY
INTERIOR
MEASUREMENT POINTS ....22 BODY DIMENSIONS ~ Body Dit
BODY DIMENSIONS AND MEASURE-
MENT METHODS
HOW BODY DIMENSIONS ARE INDICATED
1. Type A (Projected dimensions)
‘These are the dimensions measured when the measure-
ment points are projected into the reference plane, and are
the reference dimensions used for body alterations.
2. Type B (Actual-measurement dimensions)
These dimensions indicate the actual linear distance be-
‘tween measurement points, and are the reference dimen-
om sions for use if a tracking gauge is used for measure-
m [Oe |e |
sao} ae Taso T8 3 given for the dimensions of both types (A and B)
erat [37.01 |196.54) | 48.82) | 27.80) are mm (in.).
INDICATION OF REFERENCE DIMENSIONS
If the reference dimension number lin a circle) shown on the
top line of the dimension table at left is marked with
measurements are taken of this dimension and another which
are symmetrical with respect to the car centerline.
MEASUREMENT POINTS
Measurement points are used to indicate the following
1. Ifa measurement is to be made at a hole centre, the point
of the surface from which the measuring instrument is
applied is the measurement point.
seyorse
2. If a measurement is to be made at the circumference of a
hole, the point of the hole circumference of the surface
from which the measuring instrument is applied is the
measurement point.BODY DIMENSIONS — Body Dimensions and Measurement Methods
2-3
Projected dimension
savor
Hoe centre
oN
oe
Body centre point
s1vo1a0
MEASUREMENT METHODS
USING A TRACKING GAUGE
NOTE
Use a tracking gauge without looseness between gauge body
and probes.
1. TYPE A (PROJECTED DIMENSIONS)
If the length of the tracking gauge probes are adjustable,
make the measurement by lengthening one probe by the
amount equivalent to the difference in height of the two
surfaces.
2. TYPE B (ACTUAL-MEASUREMENT DIMENSIONS)
Measure by first adjusting both probes to the same length
A= A),
3. IF HOLE DIAMETERS ARE THE SAME AND THE PRO-
BES ARE CONICAL
For both Type A and Type B, insert the probes into the
holes, and then make the measurement. This method of
measurement should be used if the diameters of the holes
in the location to be measured are the same.
4. IF HOLE DIAMETERS ARE DIFFERENT, OR THE PROBES
ARE POINTED
Because measurement at the hole centers is impossible,
the circumferences must be used instead.
HOW TO DETERMINE DIMENSIONS
Desired dimensions : L = 1 + 25-9
Example mm (in)
Reference dimensions : | = 600 (23.6)
Measured hole diameters : D = 209 (0.79),
d = 109 (0.39)
Desired dimensions :
1 = 600 (23.6) + 2081079)-106 0.30)
605 (23.8)
BODY CENTRE POINTS
When measuring locations that should be symmetrical left and
Tight and there are no specific instructions with regard to
measurements in "Body Dimensions”, the body centre points
should be used to confirm that the left and right
measurements from these points are the same. One body
centre point is specified for the front of the body and another is
specified for the rear.BODY DIMENSIONS — Type A (Projected Dimensions)
2-4
anovee
2/e/@ s\e/ele
ele/elelele| e
elelels
(up was
(SNOISNAWIG G3L03rOud) V 3dAL2-5
BODY DIMENSIONS - Type A (Projected Dimensions)
‘suonsed uoyeyessu! aBne6 Buusyues euey exp seveoppuloquAS J eu :3LON
®
ale
é
é\@
e
é
é
e
8
le|
le o|
e 0
e ®
@ |
@ ®
@ [-o|
@ ®
@ ®
@ ®
el eer |e
@| 88 @
an [ae on
(up wa
BODY DIMENSIONS — Type B (Actual-Measurement Dimensions)
2-6
(eszr) errs)
osu") ‘ov v6
ON
«87
oN
up us
Ago ¥3aNN
(SNOISNAWIC LNAWSYNSVaW-TWNLOV) & 3dAL2-7
BODY DIMENSIONS — Type B (Actual-Measurement Dimensions)
ae
(oa) | wee | (exon) | 1.c0e) | (6265) | woz
ose | zee | ogc | 90st | 060't
e
| san | coe ce)
rt | 096
® | @/| 0] @
(up waBODY DIMENSIONS - Type B (Actual-Measurement Dimensions)
2-8
ouovee seq
ANN
wees coms | area [ve |eoen] er) oom
zee | ozs | eh | wer? | are | zoe
@ | @ | @ eS *O ON,
ca
AGO@ Haddn
Ts ese] wees | eaen eo] 6079/5509] wees
BaP | Set | SEE | SSR | Sao] Se | See
alo] oeloefw|ao lol] w
ANSINLHVdINOD 3NIONS2-9
BODY DIMENSIONS -— Type B (Actual-Measurement Dimensions)
ws | @
‘ue> | oN
uy was
¥OnaLNI
(er99)
‘sev't
e
glele
Aqgoa 31sBODY DIMENSIONS — Measurement Points
[curgg 9) wasp sorouseip}
904 Bununow! aquiaw 121429 40 a9)
2-10BODY DIMENSIONS — Measurement Points 2-112-12 BODY DIMENSIONS — Measurement Points
‘s2A000s|
uarier panel and side sil
Joint of
s2acore|
Joint of front pilar and side si
“Joint of roof and front pillar
hole Rear door switch mounting hole
‘Body centre point reference location2-13
BODY DIMENSIONS — Measurement Points
[utey'0) wus, serowe| [(urgs.o} wuipy serewerp] joy
2104 BununoU fe1}@q60s jo @nus) —_9foy BuNUNOW 16¥INs 100p UO
//