Professional Documents
Culture Documents
Yuken A
Yuken A
Yuken A
EC-0105
"A" SERIES PISTON PUMPS
Variable Displacement-Single,Double,
Variable / Fixed Double
PISTON
PUMPS
A
Up to 28 MPa (4060 PSI), 145 cm3/rev (8.85 CU.IN./rev)
Control Piston
Spool
Drain Port
Pivot
Flow Adj. Screw
Shaft
OUT
IN
Yoke
Features
Output Flow
20
5
Noise Level
Efficiency
8 6 16 4 60
Input Power Full Cut-off
12 3
4 3 8 2 50
4 1
0 0
0 0 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3000 PSI 0 500 1000 1500 2000 2500 3000 PSI
Pressure Pressure
No.1
"A" Series Piston Pumps
Single, Double, Variable / Fixed Double PISTON
Instructions
PUMPS
Instructions
1. Hydraulic Fluids 8. Drain Piping
Use petroleum based oils such as anti-wear type hydraulic oils Install drain piping according to the chart and ensure that
or R & O (Rust and Oxidation inhibitor) type hydraulic oils pressure within the pump housing should be maintained at a
equivalent to ISO VG-32 or 46. The recommended viscosity normal pressure of less than 0.1 MPa (14.5 PSI) and surge
range is from 20 to 400 mm2/s (98 to 1800 SSU) and pressure of less than 0.5 MPa (72.5 PSI).
temperature range is from 0 to 60° (32 to 140°F), both of which Length of piping should be less than 1 m (3.3 ft.), and the pipe
have to be satisfied for the use of the above hydraulic oils. end should be submerged in oil.
No.2
"A" Series Piston Pumps
Single, Double, Variable / Fixed Double PISTON
PUMPS
A
Instructions
No.3
"A" Series Piston Pumps
Single, Double, Variable / Fixed Double PISTON
Control Type
PUMPS
Control Type
Single Pumps
Control Type Graphic Symbols Performance Characteristics Explanation Page
Output Flow
When the system pressure increases and comes close
Pressure
to the preset cut-off pressure, the pump flow decreases
"01" Compensator automatically while maintaining the set pressure as it
6
M
Type
O is.
Pressure
Output Flow
Electro-
minimum necessary level to operate the actuator. Pump
Hydraulic
"04" Load
flow rate and cut-off pressure are controlled 37
proportional to the input current to the control device
Sensing
M
Pressure on the pump and the input current is regurated by the
Type O
Two-Pressure QH
Output Flow
SOL"OFF"
Two-Pressure QH
Output Flow
by Solenoid PH
changeover from rapid advance, to feed has been made.
Valve PL PH
M
O
Pressure
No.4
"A" Series Piston Pumps
Single, Double, Variable / Fixed Double PISTON
PUMPS
A
Control Type
Control Type
Single Pumps
Control Type Graphic Symbols Performance Characteristics Explanation Page
Output Flow
Pilot Pressure
Control Type control valve. By controlling the pilot
"07" Pressure pressure, the full cut-off pressure can be 58
Compensator
M
O remote-controlled according to your
Pressure requirements.
Control type "05", "06" and "09" are not shown in this catalogue. Contact us for the details.
Single Pumps
Model Geometric Displacement Control Type
Number cm3/rev (cu.in./rev) 01 02 03 04 04E 05 06 07 09
A10 10.0 (.610)
A16 15.8 (.964)
A22 22.2 (1.355)
A37 36.9 (2.25)
A56 56.2 (3.43)
A70 70.0 (4.27)
A90 91.0 (5.55)
A145 145 (8.85)
No.5
"A" Series Piston Pumps
Variable Displacement-Single Pumps
Pressure Compensator Type PISTON
A10 / A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Specifications
Graphic Symbol
M
O
Specifications
Geometric Minimum Operating Pres. Shaft Speed Range Approx. Mass
Displacement Adj. Flow MPa (PSI) r/min kg (lbs.)
Model Numbers
cm3/rev cm3/rev 2 1 Flange Foot
(cu. in. /rev) (cu. in. /rev) Rated Intermittent Max. Min.
Mtg. Mtg.
A10-FR01B-12∗ 5.1 (11.2)
10.0 (.610) 2 (.122) 16 (2320) 21 (3050) 1800 600
A10-FR01C/H-12∗ 8.5 (18.7)
A16-∗-R-01-∗-∗-K-32∗ 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 1800 600 16.5 (36.4) 18.7 (41.2)
A22-∗-R-01-∗-∗-K-32∗ 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 1800 600 16.5 (36.4) 18.7 (41.2)
A37-∗-R-01-∗-∗-K-32∗ 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 1800 600 28.0 (61.7) 32.3 (71.2)
A56-∗-R-01-∗-∗-K-32∗ 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 1800 600 35.0 (77.2) 39.3 (86.7)
A70-∗R01∗S-60∗ 70.0 (4.27) 30 (1.83) 25 (3630) 28 (4060) 1800 600 58.5 (129) 70.5 (155)
A90-∗R01∗S-60∗ 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) 1800 600 72.5 (160) 93 (205)
A145-∗R01∗S-60∗ 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) 1800 600 92.5 (204) 117.5 (259)
1. Whenever setting pressure, make sure the full cut-off pressure never
exceeds the maximum intermittent pressure.
information.
21 MPa (3050 PSI)
{28 MPa (4060 PSI)} ∗1
Max.
Output
Flow
0
20 MPa (2900)
{27 MPa (3920)} ∗1
No.6
"A" Series Piston Pumps
Pressure Compensator Type PISTON A
A10 / A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Model Number Designation / Pipe Flange Kit
Model Number Designation
A16 -F -R -01 -B -S -K -32 ∗
Series Direction of Control Pres. Adj. Range Port Shaft Design Design
Mounting
Number Rotation Type MPa (PSI) Position Extension Number Std.
A70 -F R 01 B S -60 ∗
Series Direction of Control Pres. Adj. Range Port Design Design
Mounting
Number Rotation Type MPa (PSI) Position Number Std.
A10
4 B: 1.2 - 7 (170 - 1020)
F: Flange
C: 2.0 - 16 (290 - 2320) 12
(10.0 cm3/rev) Mtg.
H: 2.0 - 21 (290 - 3050)
A70 Viewed from
01: Pressure 60
(70.0 cm3/rev) Shaft End
F: Flange Compensator Refer to 3
1 Type B: 1.2 - 7 (170 - 1020)
A90 Mtg. R: Clockwise C: 1.5 - 16 (220 - 2320)
S: Side Port 60
(91.0 cm3/rev) (Normal) H: 1.8 - 21 (260 - 3050)
L: Foot K: 2.0 - 28 (290 - 4060)
Mtg.
A145
60
(145 cm3/rev)
1. Available to supply pump with anti-clockwise rotation. Consult 4. When A10 pump is used as the foot Mtg., order the Mtg. Bracket kit
Yuken for details. shown below separately. Refer to page 17 for dimensions of the Mtg.
bracket.
2. The axial port is not available to the N.American Design Standard of Note: The mounting bracket kit consists of a mounting bracket, 2 hex.
A37 and A56. bolts and 2 plain washer.
3. Design Standards: None ........... Japanese Standard "JIS" Mtg. Bracket Approx. Mass
80 ............... European Design Standard Kit Numbers kg (lbs.)
90 ............... N. American Design Standard LP-1A-10 2.2 (4.9)
No.7
"A" Series Piston Pumps
Pressure Compensator Type PISTON
A10 / A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Response Characteristics
Result of Measurement
t1 t2 Full Cut-off
Pressure
No.8
"A" Series Piston Pumps
A10-FR01 PISTON
PUMPS
A
Typical Pump Characteristics
Typical Performance Characteristics of Type "A10" at Viscosity 20 mm2/s (100 SSU) [ISO VG32 Oils, 50°C (122°F)]
Efficiency
L /min L /min
80 Overall Efficiency 20 80 Overall Efficiency 20
Output Flow
60 15 U.S.GPM 60 15 U.S.GPM
Output Flow
HP kW 3 HP kW 3
Output Flow
Output Flow
8 40 10
Input Power
8 40
Input Power
10
8 6 2 8 6 2
wer
4 Powe
r 5 4 t Po 5
4 In pu t 1 4 Inpu 1
2 2
0 0 0 0
0 0
0 4 8 12 16 20 21 MPa 0 4 8 12 16 20 21 MPa
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
Pressure 3050 PSI Pressure 3050 PSI
Input Power
HP kW N=1500 r/min HP kW N=1800 r/min
8 8 P=MPa (PSI)
10 10
7 7 P= 20 (2900)
P=MPa (PSI)
P= 18 (2610)
8 6 P= 20 (2900) 8 6 P= 16 (2320)
P= 18 (2610)
P= 16 (2320) P= 14 (2030)
Input Power
Input Power
5 5
6 P= 14 (2030) 6 P= 12 (1740)
4 P= 12 (1740) 4 P= 10 (1450)
P= 10 (1450) P= 8 (1160)
4 3 P= 8 (1160) 4 3 P= 6 (870)
P= 6 (870)
2 P= 4 (580) 2 P= 4 (580)
2 P= 2 (290) 2 P= 2 (290)
1 1
0 0
0 0
0 5 10 15 20 L /min 0 5 10 15 20 L /min
0 1 2 3 4 5 U.S.GPM 0 1 2 3 4 5 U.S.GPM
Output Flow Output Flow
A10-FR01C
.6 40 1500 r/min
0.4 A10-FR01C
0.5 1800 r/min
.4 A10-FR01B
1500 r/min
0.2 20
min
.2 800 r/
A10-FR01B 1500,1
0 0
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
Full Cut-off Pressure 3050 PSI Pressure 3050 PSI
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB (A) dB (A)
N=1500 r/min N=1800 r/min
70 70
Full Flow
Full Flow
Noise Level
Noise Level
60 60
50 50
Full Cut-off Full Cut-off
40 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3000 0 500 1000 1500 2000 2500 3000
3050 PSI 3050 PSI
Pressure Pressure
No.9
"A" Series Piston Pumps
A16-∗-R-01 PISTON
Typical Pump Characteristics
PUMPS
Typical Performance Characteristics of Type "A16" at Viscosity 20 mm2/s (100 SSU) [ISO VG32 Oils, 50°C (122°F)]
Input Power
Output Flow
20 20
Output Flow
Output Flow
5 5
Input Power
Efficiency
Efficiency
8 6 16 4 8 6 16 4
Input Power
12 3 12 3
Input Power
4 3 8 2 4 3 8 2
4 1 4 1
0 0 0 0
0 0 0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 10 MPa (1450 PSI), a flow 20 L /min (5.3 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 3.7 kW (5 HP) as shown the dotted line in the graph.
HP kW N=1500 r/min HP kW P=MPa(PSI)
N=1800 r/min
16 12 16 12
P=MPa(PSI) P= 20 (2900)
P= 20 (2900) P= 18 (2610)
10 10
P= 18 (2610) P= 16 (2320)
12 12
P= 16 (2320) P= 14 (2030)
8 8
Input Power
Input Power
P= 14 (2030) P= 12 (1740)
P= 12 (1740) P= 10 (1450)
8 6 8 6
P= 10 (1450) P= 8 (1160)
P= 8 (1160) P= 6 (870)
4 4
P= 6 (870) P= 4 (580)
4 4
P= 4 (580) P= 2 (290)
2 2
P= 2 (290) P= 0.7 (100)
0 P= 0.7 (100) 0
0 0
0 5 10 15 20 25 30 L /min 0 5 10 15 20 25 30 L /min
0 1 2 3 4 5 6 7 8 U.S.GPM 0 1 2 3 4 5 6 7 8 U.S.GPM
Output Flow Output Flow
150
1.5 1800 r/min
1.0 2
1800 r/min 100
1.0
Drain
A16-∗-R-01-C
0.5 1
.5 A16-∗-R-01-C 50
N=1500 r/min
N=1500 r/min
A16-∗-R-01-B
0 A16-∗-R-01-B 0 1500,1800 r/min
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover
dB(A) dB(A) N=1800 r/min
N=1500 r/min
80 80
70 70
Noise Level
Noise Level
Full Flow
Full Flow
60 60
50 50
Full Cut-off Full Cut-off
40 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
No.10
"A" Series Piston Pumps
A22-∗-R-01 PISTON
PUMPS
A
Typical Pump Characteristics
Typical Performance Characteristics of Type "A22" at Viscosity 20 mm2/s (100 SSU) [ISO VG32 Oils, 50°C (122°F)]
Efficiency
% N=1500 r/min % N=1800 r/min
Efficiency
Output Flow
16
Output Flow
12 60 30 8 12 60 30 8
Overall Efficiency
10 10
Input Power
Input Power
12 6 12 6
8 20 8 20
8 6 4 8 6 4
Input Power Input Power
4 10 4 10
4 2 4 2
2 2
0 0 0 0 0
0 0 0
0 4 8 12 16 MPa 0 4 8 12 16 MPa
0 500 1000 1500 2000 2320 PSI 0 500 1000 1500 2000 2320 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 10 MPa (1450 PSI), a flow 30 L /min (7.9 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 5.4 kW (7.2 HP) as shown the dotted line in the graph.
HP HP
14 kW N=1500 r/min 14 kW N=1800 r/min
10 10
P=MPa(PSI) P= 14 (2030)
12 12
P= 14 (2030) P= 12 (1740)
8 8
10 P= 12 (1740) 10 P= 10 (1450)
P= 10 (1450)
P= 8 (1160)
Input Power
Input Power
8 6 8 6
P= 8 (1160)
P= 6 (870)
6 P= 6 (870) 6
4 4 P= 4 (580)
P= 4 (580)
4 4
P= 2 (290) P= 2 (290)
2 2
2 P= 1 (145) 2 P= 1 (145)
0 0 P=MPa(PSI)
0 0
0 10 20 30 40 50 L /min 0 10 20 30 40 50 L /min
0 2 4 6 8 10 12 13 U.S.GPM 0 2 4 6 8 10 12 13 U.S.GPM
Output Flow Output Flow
1.5 A22-∗-R-01-C
1.0 2
Drain
100
1.0 1800 r/min
N=1500 r/min
0.5 1
50 A22-∗-R-01-B
.5
N=1500 r/min 1500,1800 r/min
0 A22-∗-R-01-B 0
Full Flow
0 0
0 4 8 12 16 MPa 0 4 8 12 16 MPa
0 500 1000 1500 2000 PSI 0 500 1000 1500 2000 PSI
Full Cut-off Pressure 2320 Pressure 2320
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Noise Level
Noise Level
70 70
Full Flow Full Flow
60 60
0 500 1000 1500 2030 PSI 0 500 1000 1500 2030 PSI
Pressure Pressure
No.11
"A" Series Piston Pumps
A37-∗-R-01 PISTON
Typical Pump Characteristics
PUMPS
Typical Performance Characteristics of Type "A37" at Viscosity 20 mm2/s (100 SSU) [ISO VG32 Oils, 50°C (122°F)]
Efficiency
Efficiency
Output Flow
Output Flow
30 12 30 12
Input Power
Input Power
20 40 20 40
20 8 20 8
Input Power Input Power
10 20 10 20
10 4 10 4
0 0 0 0
0 0 0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 16 MPa (2320 PSI), a flow 45 L /min (11.9 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 12.6 kW (16.9 HP) as shown the dotted line in the graph.
HP P=MPa(PSI) HP P=MPa(PSI)
35 kW N=1500 r/min 35 kW N=1800 r/min
25 P= 20 (2900) 25 P= 20 (2900)
30 P= 18 (2610) 30 P= 18 (2610)
20 P= 16 (2320) 20 P= 16 (2320)
25 P= 14 (2030) 25 P= 14 (2030)
Input Power
Input Power
P= 12 (1740) P= 12 (1740)
20 15 20 15
P= 10 (1450) P= 10 (1450)
15 P= 8 (1160) 15 P= 8 (1160)
10 P= 6 (870) 10
P= 6 (870)
10 P= 4 (580) 10 P= 4 (580)
5 P= 2 (290) 5 P= 2 (290)
5 5
P= 1 (150) P= 1 (150)
0 0
0 0
0 10 20 30 40 50 60 70 L /min 0 10 20 30 40 50 60 70 L /min
0 2 4 6 8 10 12 14 16 18 U.S.GPM 0 2 4 6 8 10 12 14 16 18 U.S.GPM
Output Flow Output Flow
A37-∗-R-01-C
3 A37-∗-R-01-H
2 120 2 N=1500 r/min
N=1800 r/min
Drain
2 90
A37-∗-R-01-C
1 60 1
1 A37-∗-R-01-B
N=1500 r/min 30 1500,1800 r/min
0 A37-∗-R-01-B 0 Full Flow
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
70 70
Noise Level
Noise Level
Full Flow
Full Flow
60 60
Full Cut-off Full Cut-off
50 50
40 40
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
No.12
"A" Series Piston Pumps
A56-∗-R-01 PISTON
PUMPS
A
Typical Pump Characteristics
Typical Performance Characteristics of Type "A56" at Viscosity 20 mm2/s (100 SSU) [ISO VG32 Oils, 50°C (122°F)]
Efficiency
Efficiency
Overall Efficiency 80
80
Overall Efficiency
L /min
U.S.GPM
60 60 120
L /min Output Flow 30
HP U.S.GPM HP
100 100
60 kW Output Flow 25 60 kW 25
Output Flow
40 80 20 40 80 20
Output Flow
Input Power
Input Power
40 60 15 40 60 15
Input Power
20 40 10 20 40 10
20 Input Power 20
20 5 20 5
0 0 0 0
0 0 0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
Input Power
Example: At a pressure of under 16 MPa (2320 PSI), a flow 70 L /min (18.5 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 20.8 kW (27.9 HP) as shown the dotted line in the graph.
kW N=1500 r/min kW N=1800 r/min
HP 40 P= 20 (2900) HP 40 P= 20 (2900)
50 50
P= 18 (2610) P= 18 (2610)
35 35
P= 16 (2320) P= 16 (2320)
40 30 40 30 P= 14 (2030)
P= 14 (2030)
Input Power
P= 12 (1740)
Input Power
25 P= 12 (1740) 25
30 30 P= 10 (1450)
20 P= 10 (1450) 20
P= 8 (1160)
P= 8 (1160)
20 15 20 15 P= 6 (870)
P= 6 (870)
P= 4 (580)
10 P= 4 (580) 10
10 10 P= 2 (290)
5 P= 2 (290) 5 P=MPa(PSI)
0 P=MPa(PSI) 0
0 0
0 20 40 60 80 100 120 L /min 0 20 40 60 80 100 120 L /min
0 5 10 15 20 25 30 U.S.GPM 0 5 10 15 20 25 30 U.S.GPM
Output Flow Output Flow
2 2 A56-∗-R-01-C
2 100
N=1500 r/min
Full Flow
1 1 A56-∗-R-01-B
1 50 1500,1800 r/min
N=1500 r/min
0 0
0 0
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Noise Level
Noise Level
70 70
Full Flow Full Flow
60 60
Full Cut-off Full Cut-off
50 50
0 4 8 12 16 20 MPa 0 4 8 12 16 20 MPa
21 21
0 500 1000 1500 2000 2500 3050 PSI 0 500 1000 1500 2000 2500 3050 PSI
Pressure Pressure
No.13
"A" Series Piston Pumps
A70-∗R01 PISTON
Typical Pump Characteristics
PUMPS
Typical Performance Characteristics of Type "A70" at Viscosity 32 mm2/s (150 SSU) [ISO VG32 Oils, 40°C (104°F)]
Efficiency
Overall Efficiency L /min
Overall Efficiency
80 80 140 U.S.GPM
L /min 35
Output Flow
Volumetric Efficiency
60 120 U.S.GPM 60 Output Flow 120
30 30
HP kW HP kW
Output Flow
80 60 Output Flow 100 80 60 100
25 Volumetric Efficiency 25
Input Power
Input Power
60 60
40 80 40
20 Input Power
40 Input Power 40
20 20
20 20
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Input Power
Example: At a pressure of under 20 MPa (2900 PSI), a flow 70 L /min (18.5 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 26 kW (35 HP) as shown the dotted line in the graph.
HP kW N=1500 r/min HP kW N=1800 r/min P=MPa(PSI)
80 60 80 60 P= 24 (3480)
P=MPa(PSI) P= 22 (3190)
50 P= 24 (3480) 50 P= 20 (2900)
60 P= 22 (3190) 60 P= 18 (2610)
40 P= 20 (2900) 40 P= 16 (2320)
Input Power
Input Power
P= 18 (2610) P= 14 (2030)
P= 16 (2320) P= 12 (1740)
40 30 P= 14 (2030) 40 30
P= 12 (1740) P= 10 (1450)
P= 10 (1450) P= 8 (1160)
20 P= 8 (1160) 20 P= 6 (870)
20 P= 6 (870) 20 P= 4 (580)
10 P= 4 (580) 10 P= 2 (290)
P= 2 (290)
0 0
0 0
0 20 40 60 80 100 120 140 L /min 0 20 40 60 80 100 120 140 L /min
0 10 20 30 35 U.S.GPM 0 10 20 30 35 U.S.GPM
Output Flow Output Flow
5 300 5
Full Cut-off Power
200
4 3 3
1500 r/min
2 2
2 100
1 1 Full Flow
1500,1800 r/min
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Full Cut-off Pressure 3630 Pressure 3630
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
80 80
Noise Level
Noise Level
70 70 Full Flow
Full Flow
60 60
Full Cut-off Full Cut-off
50 50
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
No.14
"A" Series Piston Pumps
A90-∗R01 PISTON
PUMPS
A
Typical Pump Characteristics
Typical Performance Characteristics of Type "A90" at Viscosity 32 mm2/s (150 SSU) [ISO VG32 Oils, 40°C (104°F)]
Efficiency
Efficiency
Output Flow
80
Output Flow
Output Flow 42
36 100
HP kW
80 60 130 80 60 150 40
34
Input Power
Input Power
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Input Power
Example: At a pressure of under 18 MPa (2610 PSI), a flow 110 L/min (29.1 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 34 kW (46 HP) as shown the dotted line in the graph.
HP P=MPa(PSI)
kW N=1500 r/min 100 kW N=1800 r/min P= 25 (3630)
70 70
P=MPa(PSI) P= 24 (3480)
HP
P= 25 (3630) P= 22 (3190)
80 60 80 60
P= 24 (3480) P= 20 (2900)
P= 22 (3190) P= 18 (2610)
50 P= 20 (2900) 50
60 60 P= 16 (2320)
P= 18 (2610)
P= 14 (2030)
Input Power
Input Power
40 P= 16 (2320) 40
P= 14 (2030) P= 12 (1740)
40 30 P= 12 (1740) 40 30 P= 10 (1450)
P= 10 (1450) P= 8 (1160)
20 P= 8 (1160) 20 P= 6 (870)
P= 6 (870) P= 4 (580)
20 P= 4 (580) 20
10 P= 2 (290) 10 P= 2 (290)
0 0
0 0
0 20 40 60 80 100 120 140 L /min 0 20 40 60 80 100 120 140 160 L /min
0 5 10 15 20 25 30 35 U.S.GPM 0 5 10 15 20 25 30 35 40 45 U.S.GPM
Output Flow Output Flow
5 400
Full Cut-off Power
6 6
4 300
Drain
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
3630 3630
Full Cut-off Pressure Pressure
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) dB(A) N=1800 r/min
N=1500 r/min
80 80
70 Full Flow
Noise Level
Noise Level
70
Full Flow
60 60
Full Cut-off Full Cut-off
50 50
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
3630 3630
Pressure Pressure
No.15
"A" Series Piston Pumps
A145-∗R01 PISTON
Typical Pump Characteristics
PUMPS
Typical Performance Characteristics of Type "A145" at Viscosity 32 mm2/s (150 SSU) [ISO VG32 Oils, 40°C (104°F)]
Efficiency
Overall Efficiency Overall Efficiency
80 80
Volumetric Efficiency
60 60
L /min U.S.GPM Volumetric Efficiency L /min
Output Flow 220 58 270 U.S.GPM
Output Flow
70
56
Output Flow
210 Output Flow 260
HP kW HP kW 68
54
160 120 200 160 120 250 66
Input Power
Input Power
120 120
80 80 240
80 Input Power 80 Input Power
40 40
40 40
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
Input Power
Example: At a pressure of under 20 MPa (2900 PSI), a flow 180 L/min (47.6 U.S.GPM), and rotation 1500 r/min, the
axial input becomes about 64 kW (86 HP) as shown the dotted line in the graph.
kW N=1500 r/min P=MPa(PSI) HP kW N=1800 r/min P=MPa(PSI)
140 140 P= 28 (4060)
HP P= 28 (4060) 180
P= 26 (3770) P= 26 (3770)
160 120 160 120 P= 24 (3480)
P= 24 (3480) P= 22 (3190)
140 P= 22 (3190) 140
100 P= 20 (2900) 100 P= 20 (2900)
120 P= 18 (2610) 120 P= 18 (2610)
Input Power
Input Power
80 P= 16 (2320) 80 P= 16 (2320)
100 100 P= 14 (2030)
P= 14 (2030)
80 60 P= 12 (1740) 80 60 P= 12 (1740)
P= 10 (1450) P= 10 (1450)
60 P= 8 (1160) 60 P= 8 (1160)
40 40 P= 6 (870)
40 P= 6 (870) 40
P= 4 (580) P= 4 (580)
20 20 P= 2 (290) 20 P= 2 (290)
20
0 P= 1 (145) 0 P= 1 (145)
0 0
0 40 80 120 160 200 240 L /min 0 40 80 120 160 200 240 280 L /min
0 10 20 30 40 50 60 U.S.GPM 0 10 20 30 40 50 60 70 U.S.GPM
Output Flow Output Flow
10 7.5 7.5
1800 r/min Full Cut-off
400
1800 r/min
1500 r/min
Drain
5.0 5
1500 r/min
5
200
2.5 2.5
Full Flow
0 0
0 0
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Full Cut-off Pressure 3630 Pressure 3630
Noise Level [One metre (3.3 ft.) horizontally away from pump head cover]
dB(A) N=1500 r/min dB(A) N=1800 r/min
90 90
Noise Level
Noise Level
80 80
Full Flow
Full Flow
70 70
Full Cut-off
Full Cut-off
60 60
0 5 10 15 20 25 MPa 0 5 10 15 20 25 MPa
0 1000 2000 3000 3500 PSI 0 1000 2000 3000 3500 PSI
Pressure 3630 Pressure 3630
No.16
"A" Series Piston Pumps
A10-FR01 PISTON
PUMPS
A
Installation Drawing
(4.06)
65(2.56)
41(1.61)
2 Places
(3.35)
103
85
(6.57)
167
31(1.22)
(.47)
12
19.02(.7488) Dia.
82.50(3.248) Dia.
21.24(.836)
21.08(.830)
10.5(.41)
19.05(.7500)
82.55(3.250)
2 3 2 3
Suction Port 25 25 Discharge Port 106
"C" Thd. (.98) (.98) "C" Thd. 131 (4.17)
64.5 64.5 130
(5.16) (5.12)
(2.54) (2.54) 156
93(3.66) Dia.
(6.14)
159.5
(6.28)
Thread Size
Model Numbers
"C" Thd. "D" Thd.
Flange Mtg.: A10-FR01B-12/1280/1290
A10-FR01∗-12 Rc 1/2 Rc 3/8
A10-FR01∗-1280 1/2 BSP.F 3/8 BSP.F
A10-FR01∗-1290 1/2 NPT 3/8 NPT
DIMENSIONS IN
MILLIMETRES (INCHES)
Mounting Bracket Kit: LP-1A-10
17
(.67) 12(.47) Dia. Through
Mtg. Bracket 24(.94) Dia. Spotface
4 Places
(5.73)
145.5
(3.15)
80
(.12)
3
(.59)
(.55)
Hex. Bolt
15
14
(2 Pcs.) 50 56.5 95
M10×25 Lg. (1.97) (2.22) (3.74)
95 27.5 72.5 72.5
Plain Washer
(2 Pcs.) (3.74) (1.08) (2.854) (2.854)
180
(7.09)
No.17
"A" Series Piston Pumps
A16 / A22-F-R-01 PISTON
Installation Drawing
PUMPS
82.55(3.250) Dia.
DEC. INC. 25(.98)
96(3.78)
4.76(.1874)
(4.29)
109
(2.44)
82.50(3.248)
(7.36)
62
187
(1.874)
47.6
(.47)
(.71)
12
18
19.02(.7488) Dia.
21.24(.836)
21.08(.830)
19.05(.7500)
R12
"D" Thd. 95(3.74) Dia.
22.2 17(.67) Deep (R .47)
Suction Port 12 106
(.874) 8 Places
19(.75) Dia. 65 (.47) (4.17)
Discharge Port 172 130
(2.56)
19 (.75) Dia. (6.77) (5.12)
188
(7.40)
Install the pump so that the "Filling Port" is at the top.
(3.15)
(.59)
(.55)
15
14
80
3(.12)
50 56.5 95
(1.969) (2.22) (3.74)
95 27.5 72.5 72.5
(3.74) (1.08) (2.854) (2.854)
180
(7.09)
For other dimensions, refer to "Flange Mtg.".
DIMENSIONS IN
Side Port Type MILLIMETRES (INCHES)
Flange Mtg.: A16-F-R-01-∗-S-K-32/3280/3290
A22-F-R-01-∗-S-K-32/3280/3290 Discharge Port 19 (.75) Dia.
Rear Side
"D" Thd. 17 (.67) Deep Suction Port 19 (.75) Dia.
4 Places (Both Sides) 44.5
188 Fully Extended (1.75)
(7.40) 219(8.62)
78(3.07) 109(4.29)
47.6(1.874)
74 74 22.2
(2.91) (2.91) (.874)
Surface of Suction Port Surface of Discharge Port 150.5
(5.93)
For other dimensions, refer to "Axial Port Type".
No.18
"A" Series Piston Pumps
A37-F-R-01 PISTON
PUMPS
A
Installation Drawing
(4.13)
112
105
(.98)
(2.68)
25
(.55)
68
(7.95)
14
(2.311)
202
58.7
22.20(.8740) Dia.
25.01(.985)
24.85(.978)
101.55(3.998) Dia.
R14
22.23(.8752)
(R .55)
101.60(4.000)
120(4.72) Dia.
Suction Port 30.2 12
M10 Thd. 19(.75) Deep 146
32(1.26) Dia. (1.189) (.47)
8 Places (5.75)
72 195
Discharge Port 32 (1.26) Dia. 174
(2.83) (7.68) (6.85)
202
(7.95)
Install the pump so that the "Filling Port" is at the top.
Note: "Axial Port Type" is not available for N.American design Standard.
102
3(.12)
15
14
60 74 120
(2.362)(2.91) (4.72)
115 39 95 95
(4.53) (1.54) (3.740) (3.740)
230
(9.06)
58.7(2.311)
202(7.95)
86 86 30.2
(3.39) (3.39) (1.189)
Surface of Surface of 178.5
Suction Port Discharge Port (7.03)
For other dimensions, refer to "Axial Port Type".
Foot Mtg. Type; Mounting bracket is common to that of "Axial Port Type".
No.19
"A" Series Piston Pumps
A56-F-R-01 PISTON
Installation Drawing
PUMPS
35.32(1.391)
35.14(1.383)
17(.67) Hex. INC. 40 7.97(.3138)
Dia.
(1.57) 7.94(.3126)
(5.43)
138
DEC.
101.60(4.000)
101.55(3.998)
(3.54)
(3.03)
(.55)
90
14
77
(9.29)
(2.311)
236
(.98)
58.7
25
31.70(1.248) Dia.
R14
31.75(1.250)
120(4.72) Dia. (R.55)
Suction Port 30.2 "MIO" Thd. 19(.75) Deep 12 146
35(1.38) Dia. (.189) 8 Places (.47) (5.75)
26 207 174
Discharge Port 32 (1.26) Dia. (8.15) (6.85)
(2.99)
232
(9.13)
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of the two drain ports at your option. Keep the remaining port plugged. Note that on the European design standard (3280 Design),
only the left side, as viewed from the shaft end, of the drain port is machined.
Note: "Axial Port Type" is not available for N.American design Standard.
(.59)
102
3(.12)
14
15
60 77 120
(2.362) (3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
DIMENSIONS IN
Side Port Type MILLIMETRES (INCHES)
Flange Mtg.: A56-F-R-01-∗-S-K-32/3280/3290
Discharge Port 30 (1.18) Dia.
Rear Side
"D" Thd. "E" Deep Suction Port 35 (1.38) Dia. E
4 Places (Both Sides) Model Numbers "C" Thd. "D" Thd.
232 Fully Extended 62(2.44) mm (IN.)
A56-F-R-01-S-∗-K-32
(9.13) 259.5(10.22)
Rc 3/4
M 10 19 (.75)
A56-F-R-01-S-∗-K-3280 3/4 BSP.F
(5.43)
58.7(2.311)
(9.29)
236
No.20
"A" Series Piston Pumps
A70-FR01 PISTON
PUMPS
A
Installation Drawing
(7.17)
Y X
182
4 Places
14(.55)
(3.54)
90
(2.063)
(7.09)
(4.50)
52.4
114.4
180
18(.71)
14(.55)
31.70(1.248) Dia.
(4.65)
118
126.95(4.998) Dia.
31.75(1.250)
35.32(1.391)
35.14(1.383)
Discharge Port
26(1.02) Dia.
127.00(5.000)
16
26.2 (.63) 114.4 35(1.38) Dia.
(1.301) 18 (4.50) Spotface
"E" Thd. (.71) 134 (From Rear)
17(.67) Deep 246.5 (5.28) 2 Places
4 Places (9.70) 181
(7.13)
211
(8.31)
Eye Bolt
1 M10
Filling Port
[22(.87) Hex. Head Plug Furnished]
Suction Port
38(1.50) Dia.
(2.752)
Flow Adj. Screw 69.9
17(.67) Hex. Pressure Adj. Screw
17(.67) Hex.
DEC.
INC. "D" Thd. "F" Deep
4 Places
3
Case Drain Port 35.7
View Arrow Y 5(.20) Hex. Soc. (1.406)
246.5
(9.70)
View Arrow X
1. Install the pump so that the "Filling Port" is at the top. F
2. Use either port of the two drain ports at your option. Keep the Model Numbers "C" Thd. "D" Thd. "E" Thd.
mm (IN.)
remaining port plugged. Note that on the European design standard
(6080 design), only the left side, as viewed from the shaft end, of the A70-FR01∗S-60 Rc 3/4
M 12 M 10 19 (.75)
drain port is machined. A70-FR01∗S-6080 3/4 BSP.F
3. Case drain port is available for use when draining hydraulic fluid A70-FR01∗S-6090 3/4 NPT 1/2-13 UNC 3/8-16 UNC 21 (.83)
from pump casing.
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A70-LR01∗S-60/6080/6090
42.5
(1.67)
(5.00) Dia.
4 Places
(5.12)
130
(.12)
3
24(.94)
25(.98)
125 77 171
(4.921) (3.03) (6.73)
195 37 130 130
(7.68) (1.46) (5.118) (5.118)
320
(12.60)
For other dimensions, refer to "Flange Mtg.".
No.21
"A" Series Piston Pumps
A90-FR01 PISTON
Installation Drawing
PUMPS
63(2.48)
(7.50)
190.5
(4.45)
58.7(2.311)
113
Y 9.56(.3764)
(6.362)
161.6
9.53(.3752) X
(5.00)
127
38.05(1.498) Dia.
152.35(5.998) Dia.
Discharge Port
42.36(1.668)
42.18(1.661)
32(1.26) Dia. 21.5(.85) Dia. Through R22
38.10(1.500)
22
152.40(6.000)
30.2 (.87) 39(1.54) Dia. Spotface 161.6 (R.87)
"E" Thd. (1.189) (From Rear) (6.362)
"F" Deep 23
4 Places
4 Places (.91)
270
(10.63) 3
Case Drain Port
5(.2) Hex. Soc.
Eye Bolt
Pressure Adj. Screw M10
Flow Adj. Screw 17(.67) Hex. 1
17(.67) Hex. Filling Port
[27(1.06) Hex. Head Plug Furnished]
INC. Suction Port
DEC. 48(1.89) Dia.
(3.063)
77.8
View Arrow Y
"D" Thd. "F" Deep
4 Places
42.9
(1.689)
270
(10.63)
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A90-LR01∗S-60/6080/6090
25(.98)
(5.51)
140
(.12)
3
No.22
"A" Series Piston Pumps
A145-FR01 PISTON
PUMPS
A
Installation Drawing
(7.81)
198.5
11.14
11.11
(4.33)
110
.4386
(2.311)
(9.00)
228.6
.4374
58.7
(5.55)
141
Discharge Port
44.40(1.748) Dia.
152.35(5.998) Dia.
49.39(1.944)
49.21(1.937)
32(1.26) Dia.
44.45(1.750)
152.40(6.000)
30.2 24 R22 228.6 21.5(.85) Dia. Through
"E" Thd. "H" Deep (1.189) (.94) (R .87) (9.00) 39(1.54) Dia. Spotface
4 Places 273 (From Rear)
26
(10.75) 4 Places
3 (1.02)
Case Drain Port 299.5
5(.2) Hex. Soc. (11.79)
1
Filling Port
[27(1.06) Hex. Head Plug Furnished]
Eye Bolt
M10
Pressure Adj. Screw
17(.67) Hex.
1. Install the pump so that the "Filling Port" is at the top.
INC. 2. Use either port of the two drain ports at your option. Keep the
Suction Port remaining port plugged. Note that on the European design standard
48(1.89) Dia. (6080 design), only the left side, as viewed from the shaft end, of the
drain port is machined.
(3.063)
77.8
3. Case drain port is available for use when draining hydraulic fluid
from pump casing.
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg.: A145-LR01∗S-60/6080/6090
(.12)
3
29(1.14)
30(1.18)
No.23
"A" Series Piston Pumps
A10-FR01 PISTON
Spare Parts List
PUMPS
CAUTION
A10-FR01∗-12/1280/1290 When making replacement of seals or bearings,
please do it carefully after reading through the
relevant instructions in the Operator's Manual.
X
37 41 64 39 23 37 36 35 38 25 23 22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
24 X
6
5
34 33 32 31 30 29 28 27 26 1 2 3 4
51 52 53 54 55 56 57 58 59 60 61
63 62
Section X-X
No.24
"A" Series Piston Pumps
A16 / A22 / A37 / A56-∗-R-01 PISTON
PUMPS
A
Spare Parts List
A16/A22/A37/A56-∗-R-01-∗-∗-K-32/3280/3290
56
25 40 35 9 43 2 44 3 25 11 52 60 31 4 22 1 32
27
61
X 58
X
29
57
51
5
55
54
49
53
28 50 7 30 19 33 20 17 8 10 21
38 43 37 15 18 24 12 34 39 16 41 36 6 42
47
46
23
CAUTION
When making replacement of seals or bearings,
45 please do it carefully after reading through the
relevant instructions in the Operator's Manual.
14
13
Section X-X
No.25
"A" Series Piston Pumps
A70 / A90-∗R01 PISTON
Spare Parts List
PUMPS
CAUTION
A70/A90-∗R01∗S-60/6080/6090 When making replacement of seals or bearings,
please do it carefully after reading through the
relevant instructions in the Operator's Manual.
25 26 27 28 29 30 31 32 33
63
55 27 26 55 37 12 32 56 36 67 3 1 4
53
A 51
46
9
35 42
P
45 X X
Q 60
Z
64 62
34 6
54 40
Z 47 38
48
52
66
39 25 2 61 5 33 31 13 28 16 15 14 17 29 65 30
23 58 44 11 7 8 59 22 44 70
No.26
"A" Series Piston Pumps
A145-∗R01 PISTON
PUMPS
A
Spare Parts List
CAUTION
A145-∗R01∗S-60/6080/6090 When making replacement of seals or bearings,
please do it carefully after reading through the
relevant instructions in the Operator's Manual.
58 69 51 52 36 65 62 46 65 14 8 7 33 16 3 60 37 73 59 5 61
25 9
A
59 44
X X
67 54
70 41
35 68
27 4
29 64
74 39
30 57
40 28
53 2 34 26 11 6 1 32 38 10 13 12 16 71 31 72
26 27 28 29 30 31 32 33 34
24 62 56 19 17 50 48 66 23
57 63 15 46
20
21 45 43 18 22 59 47 49
Section X-X Detail "A"
No.27
"A" Series Piston Pumps
Variable Displacement-Single Pumps
Solenoid Two Pressure Control Type PISTON
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Specifications
PL PH
Output Flow
SOL SOL
"OFF" "ON"
M
O
PL PH
Pressure
Specifications
Geometric Minimum Operating Pres. Shaft Speed Range Approx. Mass
MPa (PSI) Minimum r/min kg (lbs.)
Displacement Adj. Flow
Model Numbers Adj. Pres.
cm3/rev cm3/rev 2 1 Flange Foot
(cu. in. /rev) (cu. in. /rev) Rated Intermittent MPa (PSI) Max. Min.
Mtg. Mtg.
A16-∗-R-02-∗-K-32∗ 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 1.2 (170) 1800 600 24.5 (54.0) 26.7 (58.9)
A22-∗-R-02-∗-K-32∗ 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 1.2 (170) 1800 600 24.5 (54.0) 26.7 (58.9)
A37-∗-R-02-∗-K-32∗ 36.9 (2.25) 10 (.61) 16 (2320) 21 (3050) 1.2 (170) 1800 600 36 (79.4) 40.3 (88.9)
A56-∗-R-02-∗-K-32∗ 56.2 (3.43) 12 (.73) 16 (2320) 21 (3050) 1.2 (170) 1800 600 43 (94.8) 47.3 (104)
A70-∗R02S∗-60∗ 70.0 (4.27) 30 (1.83) 25 (3630) 25 (3630) 2 (290) 1800 600 63.5 (140) 75.5 (166)
A90-∗R02S∗-60∗ 91.0 (5.55) 56 (3.42) 25 (3630) 25 (3630) 2 (290) 1800 600 80.5 (178) 101 (223)
A145-∗R02S∗-60∗ 145 (8.85) 83 (5.06) 25 (3630) 25 (3630) 2 (290) 1800 600 97.5 (215) 122.5 (270)
1. Whenever setting pressure, make sure the full cut-off pressure never 2. When operating the pump exceeding the rated pressure, operating
exceeds the maximum intermittent pressure. conditions are restricted. Refer to page 6 for the details.
Solenoid Ratings
Voltage (V) Current & Power at Rated Voltage
Electric Coil Frequency
Source Serviceable Inrush Holding Power
Source Type (Hz)
Rating Range (A) (A) (W)
50 100 80 -110 2.42 0.51
A100 100 2.14 0.37
60 90 -120
110 2.35 0.44
50 96 -132 2.02 0.42
A120 120
60 108 -144 1.78 0.31
AC
50 200 160 -220 1.21 0.25
A200 200 1.07 0.19
60 180 - 240
220 1.18 0.22
50 192 - 264 1.01 0.21
A240 240
60 216 - 288 0.89 0.15
D12 12 10.8 - 13.2 2.45
DC
D24 24 21.6 - 26.4 1.23 29
(K Series)
D48 48 43.2 - 52.8 0.61
AC→DC R100 100 90 - 110 0.33
50 /60 29
Rectified R200 200 180 - 220 0.16
Inrush current in the above table shows rms values at maximum stroke.
No.28
"A" Series Piston Pumps
Solenoid Two Pressure Control Type PISTON A
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Model Number Designation
A70 AC
A100,A120 60
(70 cm3/rev) Viewed from
F: A200,A240
Shaft End 02:
Flange Mtg.
A90 Solenoid Two S: DC 3
60 Refer to
(91.0 cm3/rev) R: Prsuure Control Side Port D12,D24
L: 1
Type D48
Foot Mtg. Clockwise
A145 (Normal) (AC→DC Rectified)
60
(145 cm3/rev) R100,R200
1. Available to supply pump with anti-clockwise rotation. Consult 3. Design Standards: None ........... Japanese Standard "JIS"
Yuken for details. 80 ............... European Design Standard
90 ............... N. American Design Standard
2. The axial port is not available to the N. American Design Standard of
A37 and A56 series.
Performance Characteristics
For performance characteristics, refer to models of pressure compensator type on page 10 to 16.
No.29
"A" Series Piston Pumps
A16 / A22-∗-R-02 PISTON
Installation Drawing
PUMPS
Axial Port Type
Flange Mtg.: A16-F-R-02-K-∗-32/3290
A22-F-R-02-K-∗-32/3290
Fully Extended
256.5(10.10) 2
Pilot Port "PP2"
141.5 "E" Thd.
(5.37)
90 138.5
77
(3.54) (5.45)
44.5(1.75) (3.03)
Lock Nut 112 Electrical Conduit
3 53 Connection
14(.55) Hex. (4.41)
(.12) (2.09) "D" Thd. (Both Ends)
59 6.5
(2.32) (.26) 1
26.5 Filling Port
"PP1"
[22(.87) Hex. Head Plug Furnished]
(1.04)
"PP2" Drain Port
(7.70)
195.5
"C" Thd.
(6.97)
4.79(.1886)
177
(5.71)
145
(10.77)
(4.61)
25
273.5
4.76(.1874)
117
(3.78)
(.98)
96
(2.44)
X
62
18(.71)
(.47)
12
19.02(.7488) Dia.
82.50(3.248) Dia.
21.24(.836)
21.08(.830)
R14(R.55)
82.55(3.250)
19.05(.7500)
95(3.74) Dia.
12 106
Lock Nut (.47) (4.17)
17(.67) Hex. 172 130
(6.77) (5.12)
188
2
Pilot Port "PP1" (7.40)
"E" Thd.
16 23 A16-F-R-02-K-∗-3280
(.63) (.91)
Pressure Adj. Screw (PL) A22-F-R-02-K-∗-3280
Pressure Adj. 14(.55) Hex. Cable Departure
Screw (PH) INC. 3(.12)
Works at Solenoid Cable Applicable:
INC.
14(.55) Hex. Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 in.)
De-energised Conductor Area ⋅⋅⋅⋅⋅⋅ Not Exceeding 1.5mm2(.002 Sq. IN.)
Works at Solenoid
Energised 135 80.1
(5.31) (3.15)
Flow Adj. Screw d 53
5(.20) Hex. Soc. (2.09)
(6.34)
161
DEC.
(1.874)
47.6
a
b
1. Install the pump so that the "Filling Port" is at the Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd.
top.
A16/A22-F-R-02-K-∗-32 Rc 3/8 G 1/2 Rc 1/4
2. The pilot port provided is for connecting a control M10
valve, if multistage pressure control is required. A16/A22-F-R-02-K-∗-3280 3/8 BSP.F 1/4 BSP. Tr
A16/A22-F-R-02-K-∗-3290 3/8 NPT 1/2 NPT 1/4 NPT 3/8-16 UNC
No.30
"A" Series Piston Pumps
A37-∗-R-02 PISTON
PUMPS
A
Installation Drawing
(7.85)
199.5
(7.13)
181
(5.87)
(11.40)
32(1.26) 6.38(.2512)
149
289.5
(4.76)
121
(4.13)
6.35(.2500)
105
(2.68)
68
(2.311)
58.7
(.55)
(.98)
25
14
101.55(3.998) Dia.
22.20(.8740) Dia.
25.01(.985)
24.85(.978)
R14(R.55)
101.60(4.000) 120(4.72) Dia.
22.23(.8752)
A37-F-R-02-S-K∗-3280
"E" Thd.
13 26
Pressure Adj. (.51) (1.02)
Screw (PH) INC. Pressure Adj. Screw (PL) Cable Departure
14(.55) Hex. 14(.55) Hex. Cable Applicable:
6(.24) Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.)
Works at Solenoid Works at Solenoid INC.
De-energised Conductor Area ⋅⋅⋅⋅⋅⋅ Not Exceeding 1.5mm2(.002 Sq. IN.)
Energised 77.1
158
Flow Adj. Screw (6.22) (3.04)
5(.20) Hex. Soc. d 50
(1.97)
(6.50)
165
DEC.
a
b
86 86
(3.39) (3.39)
Surface of Surface of mm (IN.)
Suction Port Discharge Port Model Numbers
a b d
View Arrow X A37-F-R-02-S-K-A∗-3280 198 (7.80) 186 (7.32) 39 (1.54)
A37-F-R-02-S-K-D∗-3280 209 (8.23) 197 (7.76) 39 (1.54)
1. Install the pump so that the "Filling Port" is at the top. A37-F-R-02-S-K-R∗-3280 212 (8.35) 190.2 (7.49) 53 (2.09)
2. The pilot port provided is for connecting a control valve, if For other dimensions, refer to 32/3290 design.
multistage pressure control is required.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A37-F-R-02-S-K-∗-32 Rc 1/2 G 1/2 Rc 1/4
M10 19 (.75)
A37-F-R-02-S-K-∗-3280 1/2 BSP.F 1/4 BSP. Tr
A37-F-R-02-S-K-∗-3290 1/2 NPT 1/2 NPT 1/4 NPT 7/16-14 UNC 20 (.79)
No.31
"A" Series Piston Pumps
A56-∗-R-02 PISTON
Installation Drawing
PUMPS
Side Port Type
Flange Mtg.: A56-F-R-02-S-K-∗-32/3290
Fully Extended
292(11.50)
Lock Nut 177
(6.97) 3
17(.67) Hex. Pilot Port "PP2"
90 174 "E" Thd.
(3.54) (6.85) 74
147.5 62(2.44) (2.91)
Lock Nut Electrical Conduit
(5.81) 6 50
14(.55) Hex. Connection
50.5(1.99) 9.5(.37) (.24) (1.97) "D" Thd. (Both Ends)
Filling Port 1
[22(.87) Hex. Head Plug Furnished]
43.5(1.71)
Drain Port 2
"PP1"
"C" Thd. (Both Sides) 4
"PP2" 41 49 4
(8.84)
224.5
(8.11)
206
40 7.97(.3138) (1.61) (1.93)
(6.85)
174
(5.75)
(12.70)
(1.57) 7.94(.3126)
322.5
X
146
(3.54)
(3.03)
58.7(2.311)
90
77
(.98)
(.55)
25
14
101.55(3.999) Dia.
31.70(1.2480) Dia.
35.32(1.391)
35.14(1.383)
R14(R.55)
101.60(4.000)
31.75(1.2500)
A56-F-R-02-S-K-∗-3280
3
13 26 Pilot Port "PP1"
Pressure Adj. (.51) (1.02) "E" Thd.
Screw (PH) INC. Pressure Adj. Screw (PL)
14(.55) Hex. Cable Departure
14(.55) Hex. 6(.24) Cable Applicable:
Works at Solenoid Works at Solenoid INC. Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.)
Energised De-energised Conductor Area ⋅⋅⋅⋅⋅⋅ Not Exceeding 1.5mm2(.002 Sq. IN.)
Flow Adj. Screw 170.5
5(.20) Hex. Soc. (6.71) 77.1
(7.48)
(3.04)
190
d
DEC. 50
(1.97)
a
b
100 100
(3.94) (3.94)
Surface of Surface of
Suction Port Discharge Port
View Arrow X
mm (IN.)
Model Numbers
1. Install the pump so that the "Filling Port" is at the top. a b d
2. Use either port of two drain ports at your option. A56-F-R-02-S-K-A∗-3280 223 (8.78) 211 (8.31) 39 (1.54)
A56-F-R-02-S-K-D∗-3280
Keep the remaining port plugged. Note that on the European
Design Standard (3280 Design), only the left side, as viewed 234 (9.21) 222 (8.74) 39 (1.54)
from the shaft end, of the drain port is machined. A56-F-R-02-S-K-R∗-3280 237 (9.33) 215.2 (8.47) 53 (2.09)
3. The pilot port provided is for connecting a control valve, if
multistage pressure control is required. For other dimensions, refer to 32/3290 design.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A56-F-R-02-S-K-∗-32 Rc 3/4 G 1/2 Rc 1/4
M10 19 (.75)
A56-F-R-02-S-K-∗-3280 3/4 BSP.F 1/4 BSP. Tr
A56-F-R-02-S-K-∗-3290 3/4 NPT 1/2 NPT 1/4 NPT 7/16-14 UNC 20 (.79)
No.32
"A" Series Piston Pumps
A70-FR02 PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A70-FR02S∗-60/6090
Fully Extended
354.5(13.96) Pilot Port 3
239 "PP2" "E" Thd.
(9.41) Drain Port 2
Surface of 95 95
Surface of
90 236 "C" Thd. (Both Sides) Discharge Port (3.74) (3.74) Suction Port
(3.54) (9.29) 4 73 73
209.5
62(2.44) Surface of Surface of 4
Drain Port (2.87) (2.87) Drain Port
(8.25)
65 10
(2.56) (.39)
27(1.06) Dia.
9.5(.37) Spotface
40 (From Rear)
4 Places 7.97(.3138)
(9.33)
(8.60)
(1.57)
218.5
237
202.5
(7.97)
7.94(.3126)
186.5
(7.34)
14(.55)
X
(3.54)
18(.71)
Y
90
(2.063)
(4.508)
52.4
(7.09)
114.4
180
(4.65)
118
31.70(1.248) Dia.
126.95(4.998) Dia.
35.32(1.391)
35.14(1.383)
127.00(5.000)
(2.752)
69.9
Flow Adj. Screw
17(.67) Hex.
DEC.
5 "H" Thd. "J" Deep
View Arrow X Case Drain Port
4 Places
5(.20) Hex. Soc. 35.7
(1.406)
246.5
(9.70)
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. "J" mm (IN.)
A70-FR02S∗-60 Rc 3/4 G 1/2 Rc 1/4
M10 M12 19 (.75)
A70-FR02S∗-6080 3/4 BSP.F 1/4 BSP. Tr
A70-FR02S∗-6090 3/4 NPT 1/2 NPT 1/4 NPT 7/16-14 UNC 1/2-13 UNC 21 (.83)
A70-FR02S∗-6080 1. Install the pump so that the "Filling Port" is at the top.
Cable Departure 2. Use either port of two drain ports at your option.
Cable Applicable: Keep the remaining port plugged. Note that on the European
Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.) Design Standard (6080 Design), only the left side, as viewed
Conductor Area ⋅⋅⋅⋅⋅⋅ Not Exceeding 1.5mm2(.002 Sq. IN.) from the shaft end, of the drain port is machined.
232.5 93.1
(9.15)
3. The pilot port provided is for connecting a control valve, if
(3.67) multistage pressure control is required.
d 66
(2.60) 4. Dimensions show surface of drain port.
5. Case drain port is available for use when draining hydraulic
fluid from pump casing.
a
b
DIMENSIONS IN
MILLIMETRES (INCHES)
mm (IN.)
Model Numbers
a b d Foot Mounting Type
A70-FR02SA∗-6080 236 (9.29) 224 (8.82) 39 (1.54) Mounting bracket is common to that of pressure
compensator model. Refer to page 21 for the dimensions
A70-FR02SD∗-6080 247 (9.72) 235 (9.25) 39 (1.54)
of mounting bracket.
A70-FR02SR∗-6080 250 (9.84) 228.2 (8.98) 53 (2.09)
For other dimensions, refer to 60/6090 design.
No.33
"A" Series Piston Pumps
A90-FR02 PISTON
Installation Drawing
PUMPS
Flange Mtg.: A90-FR02S∗-60/6090
2
Surface of Surface of
Drain Port Discharge Port 105 105 Suction Port
"C" Thd. (Both Sides) (4.13) (4.13)
4 4
Surface of 68 68
263.5 95 Surface of
(10.37) Drain Port (2.68) (2.68) Drain Port
(3.74) 2.5 53.5
119.5 23(.91) 3
Pilot Port (.1) (2.11) 9.56(.3764)
(4.70) "PP2" "E" Thd. 9.53(.3752)
13(.51)
63(2.48)
(9.70)
246.5
(8.94)
(8.35)
227
(7.72)
212
(7.09)
196
180
(4.45)
X
113
Y
(6.362)
(2.311)
161.6
58.7
(5.00)
127
Discharge Port
38.05(1.498) Dia.
152.35(5.998) Dia.
42.36(1.668)
42.18(1.661)
32(1.26) Dia.
38.10(1.500)
152.40(6.000)
(7.72)
196
(6.61)
Works at Solenoid
168
INC.
De-energised
(3.46)
88
(3.063)
77.8
Flow Adj. Screw
17(.67) Hex. Soc. Suction Port
DEC. 48(1.89) Dia.
View Arrow X
42.9
(1.689) "H" Thd. "K" Deep
270 4 Places
(10.63)
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. "J" mm (IN.) "K" mm (IN.)
A90-FR02S∗-60 Rc 3/4 G 1/2 Rc 1/4
M10 M12 19 (.75) 19 (.75)
A90-FR02S∗-6080 3/4 BSP.F 1/4 BSP. Tr
A90-FR02S∗-6090 3/4 NPT 1/2 NPT 1/4 NPT 7/16-14 UNC 1/2-13 UNC 20 (.79) 21 (.83)
A90-FR02S∗-6080 1. Install the pump so that the "Filling Port" is at the top.
Cable Departure
2. Use either port of two drain ports at your option.
Cable Applicable: Keep the remaining port plugged. Note that on the European
Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.) Design Standard (6080 Design), only the left side, as viewed
Conductor Area ⋅⋅⋅⋅⋅⋅ Not Exceeding 1.5mm2(.002 Sq. IN.) from the shaft end, of the drain port is machined.
257.5 56.6(2.23) 3. The pilot port provided is for connecting a control valve, if
(10.14) multistage pressure control is required.
d 53.5 4. Dimensions show surface of drain port.
(2.11)
5. Case drain port is available for use when draining hy-
draulic fluid from pump casing.
a
b
DIMENSIONS IN
MILLIMETRES (INCHES)
mm (IN.)
Model Numbers Foot Mounting Type
a b d
Mounting bracket is common to that of pressure
A90-02FRSA∗-6080 245 (9.65) 233 (9.17) 39 (1.54)
compensator model. Refer to page 22 for the dimensions
A90-02FRSD∗-6080 256 (10.08) 244 (9.61) 39 (1.54) of mounting bracket.
A90-02FRSR∗-6080 259 (10.20) 237.2 (9.34) 53 (2.09)
For other dimensions, refer to 60/6090 design.
No.34
"A" Series Piston Pumps
A145-FR02 PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A145-FR02S∗-60/6090
Surface of Surface of
Fully Extended 112 Discharge Port 112 112 Suction Port
400.5(15.77) (4.41) (4.41) (4.41)
285 23(.91) 4 4
72 72
(11.22) Surface of Surface of
2 Drain Port (2.83) (2.83) Drain Port
255.5 13(.51) Drain Port "C" Thd. 3
12 11.14(.4386)
(10.06) (Both Sides) Pilot Port (.47) 11.11(.4374)
89 "PP2" "E" Thd.
(3.50) 70(2.76)
(9.78)
248.5
(8.43)
(7.80)
X
214
198
(4.33)
110
(9.000)
(2.311)
228.6
58.7
(5.55)
141
Discharge Port
152.35(5.998) Dia.
44.40(1.748) Dia.
49.39(1.944)
49.21(1.937)
32(1.26) Dia.
44.45(1.750)
152.40(6.000)
3 1
Pressure Adj. Screw (PH) Pilot Port "PP1" Filling Port
14(.55) Hex. 68 "E" Thd. [27(1.06) Hex. Head Plug Furnished]
(2.68)
Works at Solenoid INC. Suction Port
Energised 12
(.47) Pressure Adj. Screw (PL) 48(1.89) Thd.
(3.063)
14(.55) Hex.
77.8
Works at Solenoid INC.
De-energised
Flow Adj. Screw
(9.06)
230
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. "J" mm (IN.) "K" mm (IN.)
A145-FR02S∗-60 Rc 3/4 G 1/2 Rc 1/4
M10 M12 19 (.75) 19 (.75)
A145-FR02S∗-6080 3/4 BSP.F 1/4 BSP. Tr
A145-FR02S∗-6090 3/4 NPT 1/2 NPT 1/4 NPT 7/16-14 UNC 1/2-13 UNC 20 (.79) 21 (.83)
A145-FR02S∗-6080 1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports at your option.
Cable Departure Keep the remaining port plugged. Note that on the European
Cable Applicable:
Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.) Design Standard (6080 Design), only the left side, as viewed
Conductor Area ⋅⋅⋅⋅⋅⋅ Not Exceeding 1.5mm2(.002 Sq. IN.) from the shaft end, of the drain port is machined.
92(3.62) 3. The pilot port provided is for connecting a control valve, if
278 multistage pressure control is required.
(10.94)
d 68 4. Dimensions show surface of drain port.
(2.68)
5. Case drain port is available for use when draining hydraulic
fluid from pump casing.
a
b
DIMENSIONS IN
MILLIMETRES (INCHES)
mm (IN.)
Model Numbers
a b d Foot Mounting Type
A145-FR02SA∗-6080 247 (9.72) 235 (9.25) 39 (1.54) Mounting bracket is common to that of pressure
compensator model. Refer to page 23 for the dimensions
A145-FR02SD∗-6080 258 (10.16) 246 (9.69) 39 (1.54)
of mounting bracket.
A145-FR02SR∗-6080 261 (10.28) 239.2 (9.42) 53 (2.09)
For other dimensions, refer to 60/6090 design.
No.35
"A" Series Piston Pumps
PISTON
Variable Displacement-Single Pumps
Pressure Compensator with Unloading Type
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Specifications
Output Flow
SOL SOL
"OFF" "ON"
M
O
Pressure
Specifications
Geometric Minimum Shaft Speed
Operating Pres.
Displacement Adj. Flow Unloading Pres. Range
Model Numbers MPa (PSI)
cm3/rev cm3/rev MPa (PSI) r/min
(cu. in. /rev) (cu. in. /rev) Rated Intermittent Max. Min.
A16-∗-R-03-∗-K-∗-32∗
15.8 4 16 21 1.2
1800 600
(.964) (.244) (2320) (3050) (170)
A22-∗-R-03-∗-K-∗-32∗
22.2 6 16 16 1.2
1800 600
(1.355) (.366) (2320) (2320) (170)
A37-∗-R-03-∗-K-∗-32∗
36.9 10 16 21 1.2
1800 600
(2.25) (.61) (2320) (3050) (170)
A56-∗-R-03-∗-K-∗-32∗
56.2 12 16 21 1.2
1800 600
(3.43) (.73) (2320) (3050) (170)
A70-∗R03S∗-K-60∗
70.0 30 25 25 1.2
1800 600
(4.27) (1.83) (3630) (3630) (170)
A90-∗R03S∗-K-60∗
91.0 56 25 25 1.2
1800 600
(5.55) (3.42) (3630) (3630) (170)
A145-∗R03S∗-K-60∗
145 83 25 25 1.2
1800 600
(8.85) (5.06) (3630) (3630) (170)
Consult YUKEN for details.
No.36
"A" Series Piston Pumps
Variable Displacement-Single Pumps
PISTON
A
Proportional Electro-Hydraulic Load-Sensing Type
A16 / A22 / A37 / A56 / A70 / A90 / A145
PUMPS
Model Number Designation
Graphic Symbols
i1
i2
Performance Characteristics
i1
i → Large)
M
Output Flow
i2
2
O
(Small ← Current
Input
A16/A22/A37
i1
i2
Pressure
(Small ← Input
Current i 1 →
M Large)
O
A70/A90/A145
M
O
A56
A70 -F R 04 C S -60 ∗
Direction of Pres. Adj. Range Design
Series Number Mounting Control Type Port Position Design Std.
Rotation MPa (PSI) Number
1. Available to supply pump with anti-clockwise rotation. Consult 2. Design Standards: None ........... Japanese Standard "JIS"
Yuken for details. 80 ............... European Design Standard
90 ............... N. American Design Standard
No.37
"A" Series Piston Pumps
Proportional Electro-Hydraulic Load-Sensing Type PISTON
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Pipe Flange Kits / Instructions
1. In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength
of the flanges. Therefore, please pay cautious attension to the operating pressure when the socket welding flanges are used.
2. Discharge port for pump model "A16" and "A22" is available only the threaded connections.
Detail of the pipe flange kits are given in the Catalogue No. Pub. EC-3001.
Instructions
Bleeding Air
In order to get steadily controlled pressure and flow, bleed air by loosening the air vent screw and fill solenoid armature
with operating oil.
Manual Adjustment Screws
Manual adjustment screws may be used for initial running adjustment or in case of electrical failures in order to adjust pressure and
flow temporarily. In case of normal use, put the manual adjustment screws back in their preset positions.
Connection of Surge Cut-off Valve to "A" Series Pump (For A16 to A56 Type)
If using surge cut-off valve (SF1105-A-10), connect between pilot port "PP" of this pump and port "PP" of surge cut-off valve as
pilot piping (refer to drawing below).
Inside diameter of pipe should be more than 8 mm(.32 in.).
Consult Yuken of detail of surge cut-off valve.
i1
"PP"
i2
M
O
No.38
"A" Series Piston Pumps
Proportional Electro-Hydraulic Load-Sensing Type PISTON A
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Specifications
Shaft Speed Range Max. 1800 1800 1800 1800 1800 1800 1800
r/min Min. 600 600 600 600 600 600 600
Flow Adj. L /min 1 - 28.4 1 - 40 1 - 66 1 - 101 1 - 126 1 - 163 2 - 261
Range (U.S. GPM) (.26 - 7.5) (.26 - 10.6) (.26 - 17.4) (.26 - 26.7) (.26 - 33.3) (.26 - 43.1) (.53 - 69.0)
Min Pres. Required MPa 1.5 1.5 1.5 2.0 1.0 1.0 1.0
for Flow Adj. (PSI) (220) (220) (220) (290) (145) (145) (145)
Differential Pres.
MPa 0.37 0.22
(Discharge Pres.
(PSI) (55) (30)
Flow -Load Pres.)
Control
Step Response 5
ms 70 80 120 125 100 120 210
(0 → Max. Flow)
4
Hysteresis Less than 3%
Rated Current mA 900 700 740 790 820 920 920
Coil Resistance
[20°C (68°F)] Ω 10
Coil Resistance
[20°C (68°F)] Ω 10
1. Whenever setting pressure, make sure the full cut-off pressure never
exceeds the maximum intermittent pressure.
2. When operating the pump exceeding the rated pressure, operating Pres. Step Response
Model Loading Volume
conditions are restricted. Refer to page 6 for the details. t1 t2
3. For detail specifications of power amplifiers, refer to Catalogue No. 1.5 → 16 MPa 16 → 1.5 MPa High Pressure Hose
A16, A22
Pub. EC-1305. (220 → 2320 PSI) (2320 → 220 PSI) 3/8" × 2 m (6.6 ft)
4. The figure mentioned in the above table are those obtained using
Yuken's amplifier. 2.0 → 16 MPa 16 → 2.0 MPa High Pressure Hose
A37, A56
(290 → 2320 PSI) (2320 → 290 PSI) 3/4" × 2 m (6.6 ft)
5. Step response depends on circuit and operating conditions. Data
shown in the table above is an example based on the condition right. A70, A90 3.0 → 16 MPa 16 → 3.0 MPa High Pressure Hose
A145 (435 → 2320 PSI) (2320 → 435 PSI) 1-1/4" × 2 m (6.6 ft)
No.39
"A" Series Piston Pumps
Proportional Electro-Hydraulic Load-Sensing Type PISTON
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Typical Pump Characteristics
Typical Performance Characteristics at Viscosity 20 mm2/s (100 SSU) [ISO VG32 Oils, 50°C (122°F)]
10
2
4 16 0
0
0 200 400 600 800
8 Input Current mA
2
A56
0
0 U.S.GPM L /min
0 200 400 600 800 1000 30 N=1800 r/min
110
Input Current mA 25
100
Output Flow
20 80
A37 15 60
10 40
U.S.GPM L /min N=1800 r/min
18 70 5 20
0
16 60 0
0 200 400 600 800 900
14
50 Input Current mA
12
Output Flow
10 40 A70
8 30 U.S.GPM L /min N=1800 r/min
6 35 140
20
4 30 120
Output Flow
10
2 80
0 20
0
0 200 400 600 800 40
10
Input Current mA
0 0
0 200 400 600 800 1000
Input Current mA
A90
U.S.GPM L /min N=1800 r/min A145
200
50 U.S.GPM L /min N=1800 r/min
75 280
160 70
40
240
Output Flow
120 60
30
200
50
Output Flow
20 80
160
40
10 40 120
30
0
0 20 80
0 200 400 600 800 1000
Input Current mA 10 40
0
0
0 200 400 600 800 1000
Input Current mA
No.40
"A" Series Piston Pumps
A16 / A22-F-R-04 PISTON
PUMPS
A
Installation Drawing
Flange Mtg : A16-F-R-04-∗-K-32/3280/3290
A22-F-R-04-∗-K-32/3280/3290
229 44.5(1.75)
(9.02)
213 6.5(.26)
2
Cable Departure (8.39) Filling Port
(For Pres. Control) 167.5 [22(.87) Hex. Head Plug Furnished] 101.5
(6.59) (4.00)
59(2.32) 63.2
Drain Port
"C" Thd. (2.49)
26.5(1.04)
25(.98)
(6.99)
177.5
4.79(.1886)
(6.00)
152.5
4.76(.1874)
X
(10.06)
(3.78)
255.5
96
(2.26)
57.5
(.47)
(.71)
12
18
82.50(3.248) Dia.
19.02(.7488) Dia.
21.24(.836)
21.08(.830) R12
82.55(3.250)
95(3.74) Dia.
19.05(.7500)
12 (R.47)
(.47) 106
172 (4.17)
(6.77) 130
Surface of Suction Port (5.12)
187 188
Pressure Gauge Connection (7.36) (7.40)
for Pump Discharge Pressure
262
"D" Thd (10.31) Pilot Port "PP"
Surface of Discharge Port 152.2 "D" Thd.
(5.99) 2
Cable Departure
Tank Port 70 (For Flow Control)
Air Vent "F" Thd. (2.76)
3 (.12) Hex. Soc.
Manual Pressure Adj. Screw
3 (.12) Hex. Soc. Manual Pressure Adj. Screw
3(.12) Hex. Soc.
INC. 41
Safety Valve Pressure Adj. Screw (1.61) INC.
17(.67) Hex. Soc.
(4.06)
103
(2.26)
INC.
57.5
(1.89)
48
(1.874)
47.6
G 3/8 Thd.
18.6(.73) Dia. 15°
28(1.10) Dia.
DIMENSIONS IN
MILLIMETRES (INCHES)
No.41
"A" Series Piston Pumps
A37-F-R-04 PISTON
Installation Drawing
PUMPS
Flange Mtg. : A37-F-R-04-∗-K-32/3280/3290
Manual Pressure Adj. Screw
3(.12) Hex. Soc.
Air Vent 3(.12) Hex. INC.
308.5 59 3 Places.
Air Vent 3(.12) Hex.
3 Places. (12.15) (2.32)
Cable Departure 1
296.5 9.5
(For Pres. Control)
(11.67) (.37)
Manual Flow Adj. Screw 110.5
3(.12) Hex. Soc. (4.35)
INC. 77 Filling Port
[22(.87) Hex. Head Plug Furnished] 77.3
(3.03) Safety Valve
30(1.18) (3.04)
Pressure Adj. Screw
Drain Port 3(.12) Hex. Soc.
"C" Thd. INC.
(7.30)
185.5
6.38(.2512)
(5.80)
147.2
32(1.26)
(5.20)
6.35(.2500)
132
(4.13)
(10.85)
105
275.5
(.55)
14
(.28)
(.98)
7
25
101.55(3.998) Dia.
22.20(.8740) Dia.
25.01(.985)
24.85(.978)
R14
12 120(4.72) Dia.
101.60(4.000)
22.23(.8752)
(R .55)
(.47) 146
195 (5.75)
Pressure Gauge
(7.68) 174
Connection for Pump
Surface of Suction Port (6.85)
Discharge Pressure 228
"D" Thd (8.98) 202
282 (7.95)
(11.10)
Surface of Discharge Port
100.5 115.5
(3.96) (4.55)
27
Pilot Port "PP" (1.06) Cable Departure 1 1. Cable Applicable:
"D" Thd. (For Flow Control) Outside Dia......8-10 mm (.31-.39 IN.)
Conductor Area......Not Exceeding 1.5 mm2 (.002 Sq. IN.)
(3.35)
85
(2.311)
(1.874)
58.7
47.6
Discharge Port
Suction Port 20(.79) Thd.
32(1.26) Dia. 30.2 22.2 "F" Thd. 19(.75) Deep
"E" Thd. "H" Deep (1.189) (.874) 4 Places
4 Places 36 42
(1.42) (1.65)
83
(3.27)
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A37-F-R-04-∗-K-32 Rc 1/2 Rc 1/4
M10 M10 19 (.75)
A37-F-R-04-∗-K-3280 1/2 BSP.F 1/4 BSP.Tr
A37-F-R-04-∗-K-3290 1/2 NPT 1/4 NPT 7/16-14 UNC 3/8-16 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A37-L-R-04-∗-K-32/3280/3290 14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.59)
(.55)
102
15
14
(.12)
3
60 74 120
(2.362) (2.91) (4.72)
115 39 95 95
(4.53) (1.54) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
No.42
"A" Series Piston Pumps
A56-F-R-04 PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A56-F-R-04-∗-K-32/3280/3290
Manual Pressure Adj. Screw
62 3(.12) Hex. Soc.
320.5 (2.44)
Air Vent 3(.12) Hex. INC.
(12.62) Air Vent
3 Places. 308.5 9.5 3(.12) Hex.
(12.15) (.37) 3 Places. 77.8
122.5 (3.06)
Cable Departure 1
Manual Flow Adj. Screw (4.82) (For Pres. Control) Surface of Drain Port
3(.12) Hex. Soc. 50.5
(1.95) 41 49 Safety Valve
INC. Filling Port
43.5 (1.61) (1.93) Pressure Adj. Screw
[22(.87) Hex. Head Plug Furnished]
(1.71) 40 3(.12) Hex. Soc.
(1.57) INC.
2
Drain Port (Both Sides) 7.97(.3138)
(7.30)
185.5
"C" Thd.
(5.80)
147.2
7.94(.3126)
(11.16)
X
283.5
(.28)
(3.54)
7
90
(.55)
(.98)
14
25
31.70(1.248) Dia.
101.55(3.998) Dia.
35.32(1.931)
35.14(1.383) R14
31.75(1.250)
101.60(4.000) (R.55)
12 120(4.72) Dia. 146
Pressure Gauge Connection
(.47) (5.75)
for Pump Discharge Pressure
"D" Thd 240 174
(9.45) (6.85)
Surface of Suction Port 232
240 (9.13)
(9.45)
294
(11.57)
Surface of Discharge Port
100 116
(3.94) (4.57)
27 Cable Departure 1
Pilot Port "PP"
(1.06) (For Flow Control)
"D" Thd.
1. Cable Applicable:
Outside Dia......8-10 mm (.31-.39 IN.)
Conductor Area......Not Exceeding 1.5 mm2 (.002 Sq. IN.)
2. Use either port of two pilot and drain ports at your option. Keep the
(3.70)
94
47.6
(3280 Design), only the left side, as viewed from the shaft end, of the
drain port is machined.
Suction Port Discharge Port
35(1.38) Dia. 20(.79) Thd.
"F" Thd. "H" Deep
30.2 22.2 4 Places
"E" Thd. "H" Deep
4 Places (1.189) (.874)
38 44
(1.50) (1.73)
85
(3.35)
View Arrow X Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A56-F-R-04-∗-K-32 Rc 3/4 Rc 1/4
M10 M10 19 (.75)
A56-F-R-04-∗-K-3280 3/4 BSP.F 1/4 BSP.Tr
A56-F-R-04-∗-K-3290 3/4 NPT 1/4 NPT 7/16-14 UNC 3/8-16 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A56-L-R-04-∗-K-32/3280/3290
14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.55)
(.59)
102
14
15
(.12)
3
60 77 120
(2.362)(3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
No.43
"A" Series Piston Pumps
A70-FR04 PISTON
Installation Drawing
PUMPS
Flange Mtg. : A70-FR04∗S-60/6080/6090
Cable Departure 3
Manual Pressure (For Pres. Control) Surface of
Adj. Screw Drain Port
INC. 344.5 Drain Port (Both Sides) 1
3 (.12) Hex. Soc. 196.5
(13.56) "C" Thd. Safety Valve
Air Vent Pilot Port (7.74) Pressure Adj. Screw
227.5
3 (.12) Hex. Soc. "D" Thd. 169 3 (.12) Hex. Soc.
(8.96)
3 Places (6.65) INC.
196.5 62
Secondary Pressure 140 95 Surface of Suction Port
Manual Flow (7.74) (2.44) Gauge Connection (5.51) (3.74)
Adj. Screw INC. 191.5 for Pump Discharge 104.3
3 (.12) Hex. Soc. (7.54) Pressure (4.11)
Air Vent 137 19.5 "D" Thd.
3 (.12) Hex. Soc. (5.39) (.77) 73 73
127.00 (5.000)
126.95 (4.998)
3 Places (2.87) (2.87)
Dia.
65 9.5
3
Cable Departure (2.56) (.37)
31.75 (1.250)
31.70 (1.248)
35.32 (1.391)
35.14 (1.383)
(For Flow Control)
40 7.97 (.3138)
Tank Port 7.94 (.3126)
(7.74)
(1.57)
196.5
137(5.39)
120(4.72)
"H" Thd.
14(.55)
(3.54)
(3.27)
90
X
83
180(7.09)
18(.71)
(4.50)
114.4
(1.97)
14(.55)
50
(4.65)
(1.189)
118
30.2
35 (1.38) Dia.
16(.63) Spotface
Primary Pressure (From Rear)
18(.71) 114.4
Gauge Connection for 58.7 2 Places
(4.50)
Pump Discharge Pressure (2.311)
"D" Thd. 27 (1.06) Dia. 134
215 Spotface (5.28)
"F" Thd. "K" Deep (8.46) (From Rear) 181
4 Places 276 4 Places (7.13)
(10.87) 211
Discharge Port
25 (.98) Dia. (8.31)
1
Filling Port Eye Bolt
[22 (0.87) Hex. Head plug Furnished] M10
Suction Port
38 (1.50) Dia.
(2.752)
69.9
35.7
1. Use either port of two pilot and drain ports at your option. Keep the (1.406)
246.5
remaining port plugged. Note that on the European Design Standard (9.70)
Case Drain Port 2
(6080 Design), only the left side, as viewed from the shaft end, of
5 (.20) Hex. Soc.
the drain port is machined.
2. Case drain port is available for use when draining hydraulic fluid
from pump casing. View Arrow X
3. Cable Applicable:
Outside Dia......8-10 mm (.31-.39 IN.)
Conductor Area......Not Exceeding 1.5 mm2 (.002 Sq. IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. J mm (IN.) K mm (IN.)
A70-FR04∗S-60 Rc 3/4 Rc 1/4 Rc 3/8
M12 M10 19 (.75) 17 (.67)
A70-FR04∗S-6080 3/4 BSP.F 1/4 BSP. Tr 3/8 BSP. F
A70-FR04∗S-6090 3/4 NPT 1/4 NPT 1/2-13 UNC 7/16-14 UNC 3/8 NPT 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
No.44
"A" Series Piston Pumps
A90-FR04 PISTON
PUMPS
A
Installation Drawing
(8.11)
9.56 (.3764)
206
50(1.97)
(5.39)
9.53 (.3752)
(4.72)
137
(4.45)
120
113
(3.27)
83
(6.362)
X
161.6
(5.00)
127
Tank Port
38.05(1.498) Dia.
152.35(5.998) Dia.
42.36(1.668)
42.18(1.661)
"H" Thd.
Primary Pressure
152.40(6.000)
38.1(1.500)
Suction Port
48(1.89) Thd.
(3.063)
77.8
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. J mm (IN.) K mm (IN.)
A90-FR04∗S-60 Rc 3/4 Rc 1/4 Rc 3/8
M12 M10 19 (.75) 17 (.67)
A90-FR04∗S-6080 3/4 BSP.F 1/4 BSP. Tr 3/8 BSP. F
A90-FR04∗S-6090 3/4 NPT 1/4 NPT 1/2-13 UNC 7/16-14 UNC 3/8 NPT 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model. Refer
to page 22 for the dimensions of mounting bracket.
No.45
"A" Series Piston Pumps
A145-FR04 PISTON
Installation Drawing
PUMPS
Flange Mtg. : A145-FR04∗S-60/6080/6090
Manual Pressure Cable Departure 3
Adj. Screw (For Pres. Control) Surface of Drain Port
1
3 (.12) Hex. Soc. 400 Drain Port (Both Sides) Air Vent
(15.75) "C" Thd. 216.5
3 (.12) Hex. Soc. (8.52)
INC. 280.5 112 3 Places
(11.04) 189
(4.41) Manual Flow (7.44)
249.5 23 Adj. Screw
3 (.12) Hex. Soc. 160 112
(9.82) (.91) Surface of Suction Port
(6.30) (4.41)
225 72 72
Air Vent (8.86) INC. Safety Valve
3 (.12) Hex. Soc. 13 (2.83) (2.83) Pressure Adj. Screw
3 Places 168 Pilot Port "D" Thd. 85.3
(6.61) (.51) 3(.12) Hex. Soc.
3 Secondary Pressure Gauge (3.36)
Cable Departure 89 INC.
Connection for Pump
(For Flow Control) (3.50) Discharge Pressure 11.14 (.4386)
Tank Port 70 "D" Thd. 11.11 (.4374)
(8.19)
"H" Thd. (2.76)
208
50(1.97)
(1.189)
(5.39)
(4.72)
137
30.2
(4.33)
120
(3.27)
110
83
(9.000)
228.6
X
(5.55)
141
Primary Pressure
44.40(1.748) Dia.
152.35(5.998) Dia.
49.39(1.944)
49.21(1.937)
152.40(6.000)
Eye Bolt
M10
Suction Port
48(1.89) Dia.
(3.063)
77.8
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" Thd. J mm (IN.) K mm (IN.)
A145-FR04∗S-60 Rc 3/4 Rc 1/4 Rc 3/8
M12 M10 19 (.75) 17 (.67)
A145-FR04∗S-6080 3/4 BSP.F 1/4 BSP. Tr 3/8 BSP. F
A145-FR04∗S-6090 3/4 NPT 1/4 NPT 1/2-13 UNC 7/16-14 UNC 3/8 NPT 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
No.46
"A" Series Piston Pumps
Variable Displacement-Single Pumps
Electro-Hydraulic Proportional Pressure & Flow Control Type PISTON A
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Model Number Designation
Output Flow
1 2
Pressure
Control (S ← Input Voltage → L)
Piston
Graphic Symbols
A16/A22/A37/A56 A70/A90/A145
No.47
"A" Series Piston Pumps
Electro-Hydraulic Proportional Pressure & Flow Control Type PISTON
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Specifications / Pipe Flange Kit / Instructions
Specifications
Model Numbers A16 A22 A37 A56 A70 A90 A145
Descriptions
Geometric cm3/rev 15.8 22.2 36.9 56.2 70.0 91.0 145.0
Displacement (cu. in./rev) (.964) (1.355) (2.25) (3.43) (4.27) (5.55) (8.85)
2 16 16 16 16 25 25 25
Rated
(2320) (2320) (2320) (2320) (3630) (3630) (3630)
Operating Pres.
MPa (PSI) 1 21 16 21 21 28 28 28
Intermittent
(3050) (2320) (3050) (3050) (4060) (4060) (4060)
Shaft Speed Range r/min 600 - 1800
3 L /min 28.4 40.0 66.4 101.0 126.0 163.0 261.0
Max. Flow
(U.S. GPM) (7.5) (10.6) (17.5) (26.7) (33.3) (43.1) (69.0)
No.48
"A" Series Piston Pumps
Electro-Hydraulic Proportional Pressure & Flow Control Type PISTON A
A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Typical Pump Characteristics
Output Flow
80
Output Flow
20
4 16 15 60
10 40
2 8
5 20
0 0
0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A22 A70
U.S.GPM L /min U.S.GPM L /min
12 45 40 150
40 1800 r/min
10 125 1800 r/min
1500 r/min 30
8 30 Output Flow
100 1500 r/min
Output Flow
6 20 75
20
4 50
10 10
2 25
0 0
0 0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
A90
A37 U.S.GPM L /min
45 175
L /min 1800 r/min
U.S.GPM 80 40 150
20
1500 r/min
1800 r/min 125
Output Flow
16 60 30
1500 r/min 100
Output Flow
12
40 20 75
8
50
20 10
4 25
0 0 0
0
0 1 2 3 4 5 0 1 2 3 4 5
Input Signal V DC Input Signal V DC
Note: Pump characteristics at 1800 r/min is the same as those at 1500 r/min A145
where frequency is compensated. L /min
(Refer to page 48.) U.S.GPM 280
1800 r/min
240
60
1500 r/min
Full Cut-off Pres. vs. Input Signal 50 200
Output Flow
160
PSI MPa A∗-∗R04E27.5M 40
4000 28 120
30
25
80
A∗-∗R04E24.5M 20
Full Cut-off Pressure
3000 20 10 40
A∗-∗R04E20.6M
0
0
15 0 1 2 3 4 5
2000
Input Signal V DC
10
A∗-∗R04E15.7M
1000
5
A∗-∗R04E6.9M
0 0 Refer to page 10 to 16 for performance characteristics of
0 1 2 3 4 5 pressure compensator type excluding characteristics appeared
Input Signal V DC on this catalogue.
No.49
"A" Series Piston Pumps
A16 / A22-∗R04E PISTON
Installation Drawing
PUMPS
Air Vent
4 3(.12) Hex. Soc.
Cable 3Places
Departure 205.5
(8.09)
232.5 44.5(1.75)
(9.15) Filling Port
1
147.5 [22(.87) Hex. Head Plug Furnished]
(5.81) 151.5 142
26.5 6.5(.26)
(5.96) (5.59)
(1.04) Drain Port "C" Thd.
59
25(.98)
(2.32) 95(3.74) Dia.
(6.38)
162
4.79(.1886)
4.76(.1874)
(3.78)
96
Y X
12(.47)
18(.71)
(3.07)
78
82.50(3.248) Dia.
19.02(.7488) Dia.
82.55(3.250)
19.05(.7500)
21.24(.836)
21.08(.830)
12 R12
(.47) 106
(R.47) (4.17)
172
(6.77) 130
(5.12)
Pres. Sensor 2
Connector
2
3
Tilt Angle
"D" Thd. 17(.67) Deep Sensor Connector
8 Places
47.6(1.874)
47.6(1.874)
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top. Model Numbers "C" Thd. "D" Thd.
2. Do not touch the screw because it is adjusted at the time of shipment. A16/A22-FR04E∗-∗-42 Rc 3/8
M10
3. For cable connection with amplifiers, see page 56. A16/A22-FR04E∗-∗-4280 3/8 BSP.F
4. Cable Applicable:
A16/A22-FR04E∗-∗-4290 3/8 NPT 3/8-16 UNC
Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.)
Conductor Area ⋅⋅⋅⋅⋅⋅Not Exceeding 1.5mm2(.002 Sq. IN.)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 18 for the dimensions of mounting bracket.
No.50
"A" Series Piston Pumps
A37-∗R04E PISTON
PUMPS
A
Installation Drawing
274.5
(10.81)
251.5
(9.90) Filling Port 1
224.5 [22(.87) Hex. Head Plug Furnished]
(8.84)
166.5 Drain Port "C" Thd. 151.5 146.5
(6.56) (5.96) (5.77)
77 62 86 86
Surface of Surface of
(3.03) (2.44) Discharge Port (3.39) (3.39) Suction Port
30 9.5
(1.18) (.37)
40(1.57) 120(4.72) Dia. 2
(6.54)
7.97(.3138)
166
Air Vent 7.94(.3126)
(4.13)
3 (.12) Hex. Soc.
3 Places 105
X
(2.311)
58.7
25(.98)
14(.55)
(3.54)
90
R14
101.55(3.998) Dia.
31.70(1.248) Dia.
32 (1.26) Dia.
30.2 12 146
"D" Thd. "E" Deep (1.189) (.47) (5.75)
4 Places 178.5 174
(7.03) (6.85)
252.5
(9.94)
Tilt Angle 3 Pres. Sensor 3
Sensor Connector Connector
1. Install the pump so that the "Filling Port" is at the top. Suction Port
32(1.26) Dia.
2. Do not touch the screw because it is adjusted at the time of shipment.
3. For cable connection with amplifiers, see page 56.
(2.311)
58.7
View Arrow X
DIMENSIONS IN
MILLIMETRES (INCHES)
No.51
"A" Series Piston Pumps
A56-∗R04E PISTON
Installation Drawing
PUMPS
Flange Mtg. : A56-FR04E∗-02-42/4280/4290
4
Cable Departure
Cable Applicable:
Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.) Filling Port 1
Conductor Area ⋅⋅⋅⋅⋅⋅ [22(.87) Hex. Head Plug Furnished]
Not Exceeding 1.5mm2(.002 Sq. IN.)
287
(11.30) 2
264 Drain Port "C" Thd.
(10.39) (Both Sides)
151.5 160.5
237 (5.96) (6.32)
(9.33) 100 100
Surface of Surface of
179 62 (3.94) (3.94)
Discharge Port Suction Port
(7.05) (2.44) 41 49
Surface of Drain Port Surface of Drain Port
50.5 9.5 (1.61) (1.93)
(1.99) (.37)
43.5
(1.71)
40 3
(1.57)
(7.52)
191
Air Vent 7.97(.3128)
3 (.12) Hex. Soc. 7.94(.3126)
3 Places R14
(3.54)
(R.55)
90
X
(2.311)
58.7
25(.98)
14(.55)
(3.86)
98
31.70(1.248) Dia.
101.55(3.998) Dia.
120(4.72) Dia.
31.75(1.250)
101.60(4.000)
35.32(1.391)
35.14(1.383)
Discharge Port
32 (1.26) Dia.
30.2 12 146
"D" Thd. (1.189) (.47) (5.75)
"E" Deep 191 174
4 Places (7.52) (6.85)
265
(10.43)
4 4
Tilt Angle Pres. Sensor
Sensor Connector Connector
Suction Port
35(1.38) Dia.
(2.311)
58.7
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 20 for the dimensions of mounting bracket.
No.52
"A" Series Piston Pumps
A70-∗R04E PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A70-FR04E∗∗-60-60/6080/6090
4
Cable Departure
Cable Applicable:
Outside Dia. ⋅⋅⋅⋅⋅⋅ 8-10mm(.31-.39 IN.)
Conductor Area ⋅⋅⋅⋅⋅⋅Not Exceeding 1.5mm2(.002 Sq. IN.)
333.5
(13.13)
307 2
(12.09) Drain Port "C" Thd. 116.5 155
249 (Both Sides) (4.59) (6.10)
(9.80) 62 95 95
Surface of Discharge Port Surface of Suction Port
(2.44) (3.74) (3.74)
65 19.5(.77) Surface of Drain Port 73 73
Surface of Drain Port
(2.56) (2.87) (2.87)
9.5(.37)
40(1.57)
7.97(.3138)
(8.17)
207.5
7.94(.3126)
Air Vent
3 (.12) Hex. Soc.
(3.54)
3 Places
52.4(2.063)
90
18(.71)
(7.09)
180
Y
(4.65)
118
31.70(1.248) Dia.
126.95(4.998) Dia.
127.00(.5000)
35.32(1.391)
35.14(1.383)
16 (From Rear)
"E" Thd. 26.2 (.63) 181
17(.67) Deep
(1.031) 18 (7.13)
4 Places
(.71) 211
246.5 (8.31)
(9.70)
305.5
(12.03)
5
Filling Port 1
[22(.87) Hex. Head Plug Furnished] 4
Tilt Angle
Eye Bolt Sensor Connector
M10 Pres. Sensor 4
Connector
3 3
Suction Port
38(1.38) Dia.
(2.752)
69.9
View Arrow Y
"D" Thd. "F" Deep
35.7 4 Places
(1.406)
246.5
(9.70)
Case Drain Port
5 (.20) Hex. Soc.
View Arrow X
Dimensions mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd.
F
A70-FR04E∗∗-60-60 Rc 3/4
M12 M10 19 (.75)
A70-FR04E∗∗-60-6080 3/4 BSP.F
A70-FR04E∗∗-60-6090 3/4 NPT 1/2-13 UNC 3/8-16 UNC 21 (.83)
DIMENSIONS IN
Foot Mounting Type
MILLIMETRES (INCHES)
Mounting bracket is common to that of pressure compensator model.
Refer to page 21 for the dimensions of mounting bracket.
No.53
"A" Series Piston Pumps
A90-∗R04E PISTON
Installation Drawing
PUMPS
63(2.48)
Air Vent
(8.54)
217
3 (.12) Hex. Soc. 9.56(.3764)
3 Places 3
9.53(.3752)
(4.45)
113
3 X
(6.362)
(2.311)
161.6
58.7
(5.00)
127
152.35(5.998) Dia.
38.05(1.498) Dia.
Discharge Port
32 (1.26) Dia.
152.40(6.000)
42.36(1.668)
42.18(1.661)
38.1(1.500)
Suction Port
48(1.89) Dia.
(3.063)
77.8
View Arrow X
Dimensions mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd.
F H
A90-FR04E∗∗-60-60 Rc 3/4
M12 M10 19 (.75) 19 (.75)
A90-FR04E∗∗-60-6080 3/4 BSP.F
A90-FR04E∗∗-60-6090 3/4 NPT 1/2-13 UNC 7/16-14 UNC 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 22 for the dimensions of mounting bracket.
No.54
"A" Series Piston Pumps
A145-∗R04E PISTON
PUMPS
A
Installation Drawing
(8.62)
219
3 (.12) Hex. Soc. X
(4.33)
3 Places 5
110
(9.000)
(2.311)
228.6
58.7
(5.55)
141
Discharge Port
152.35(5.9980) Dia.
44.40(1.7480) Dia.
32 (1.26) Dia.
152.40(6.0000)
44.45(1.7500)
49.39(1.944)
49.21(1.937)
(3.063)
77.8
Suction Port
48(1.89) Dia.
"D" Thd. "F" Deep
42.9 4 Places
(1.689)
299.5
(11.79)
View Arrow X
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports at your option. Keep the remaining port plugged. Note that on the European design standard (6080 Design), only
the left side, as viewed from the shaft end, of the drain port is machined.
3. Do not touch the screw because it is adjusted at the time of shipment.
4. For cable connection with amplifiers, see page 56.
5. If you do not use the special sequence valve, plug the port (FP-SC-1/32)
Dimensions mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd.
F H
A145-FR04E∗∗-60-60 Rc 3/4
M12 M10 19 (.75) 19 (.75)
A145-FR04E∗∗-60-6080 3/4 BSP.F
A145-FR04E∗∗-60-6090 3/4 NPT 1/2-13 UNC 7/16-14 UNC 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 23 for the dimensions of mounting bracket.
No.55
"A" Series Piston Pumps
A16 / A22 / A37 / A56 / A70 / A90 / A145-FR04E PISTON
Cable connection between pump and amplifier
PUMPS
Cable connection between pump and amplifier
The cable connections between the proportional pilot valve and the sensor of the pump and the attached amplifier
(SK1106) are shown below.
Proportional
Pilot Valve
"A" Series
Piston Pump
Tilt Angle
Sensor
Pressure
Sensor
1
Cable Ass'y
1 : For Solenoid
Colour of Lead Wire 2 : For Power Supply
1 3 : For Pressure Sensor
Red......Power Supply, +24V DC 4 3
White...Power Supply, 0V 4 : For Tilt Angle Sensor
Shield...Ground 5 : For Signal
1 2 3 4 5 6 1 2 3 4 5 1 2 3 4 1 2 3 1 2
2
Amplifier
Sensor
Pres.
FUSE
Supply
Power
Solenoid
Signal
Sensor
Tilt Angle
(5A)
Model : SK1106-∗-∗-∗-11
CN5
CN4
CN3
CN2
CN1
POWER
1. Cable assemblies are available. When ordering, specify the cable ass'y model numbers from the table below.
No.56
Amplifiers for Electro-Hydraulic Proportional
Pressure & Flow Control Type Pumps PISTON
PUMPS
A
Specifications / Installation Drawing
Specifications
Model No. List of Amplifier Model No.
SK1106-∗-∗-∗-10
Description Pump Model Numbers Amplifier Model Numbers
Applicable Coil Resistance 10 Ω A16-∗R04E -06-42∗ SK1106- -16-06-10
Input Impedance 10 kΩ
A22-∗R04E -11-42∗ SK1106- -22-11-10
Power Supply 24 V DC (21 - 28 V Included Ripple)
A37-∗R04E -01-42∗ SK1106- -37-01-10
Power Input (Max.) 30 W
A56-∗R04E -02-42∗ SK1106- -56-02-10
Input Signal Max. Flow/5V, Specified Pres./5V
Output Signal for Sensor Monitor 5V/Max. Flow, 5V/Specifed Pres. A70-∗R04E ∗-60-60∗ SK1106- -70-60-10
15
CN1 POWER
Solenoid
1 2
Fuse
FUSE
FUSE
(5A)
(6.50)
(5.51)
165
140
1 2 3 4 5 1 2 3 4
CN5
CN5 YUKEN KOGYO CO. LTD.
MADE IN JAPAN
(.20)
Input/Output
5
Signal
92
(3.62)
100
Connector Name of Signal (3.94)
CN1 1
Output to pilot valve solenoid
Solenoid 2
CN2 1 0 [V] (0V )
Power 2 +24 [V] (24V)
Supply 3 0 [V]
1 +5 [V]
CN3 Power Supply for Sensor
2 0 [V]
Pres.
(1.89)
Sensor
4 0 [V]
1 +8 [V]
Power Supply for Sensor N-SK 1106-10 ∗∗∗∗∗-95
CN4 2 0 [V]
Tilt
3 Input Signal - Sensor
Angle
Sensor 4 0 [V]
5
1 Input Signal - Flow (Qin)
2 Input Signal - Common (COM)
CN5 DIMENSIONS IN
Input/ 3 Input Signal - Pres. (Pin) MILLIMETRES (INCHES)
Output 4 Output Signal - Sensor Monitor P (SMP)
Signal
5 Output Signal - Sensor Monitor Q(SMQ)
6 0 [V]
No.57
"A" Series Piston Pumps
Variable Displacement-Single Pumps
Pilot Pressure Control Type Pressure Compensator
PISTON
A10 / A16 / A22 / A37 / A56 / A70 / A90 / A145 PUMPS
Specifications
Output Flow
M
O
Pressure
Specifications
Geometric Minimum Operating Pres. Shaft Speed Range Approx. Mass
MPa (PSI) Minimum r/min kg (lbs.)
Displacement Adj. Flow
Model Numbers Adj. Pres.
cm3/rev cm3/rev 2 1 Flange Foot
(cu. in. /rev) (cu. in. /rev) Rated Intermittent MPa (PSI) Max. Min.
Mtg. Mtg.
A10-FR07-12∗ 10.0 (.610) 2 (.122) 16 (2320) 21 (3050) 2.0 (290) 1800 600 8.5 (18.7) 10.7 (23.6)
A16-∗-R-07-∗-K-32∗ 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 1.2 (175) 1800 600 21 (46.3) 23.2 (51.2)
A22-∗-R-07-∗-K-32∗ 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 1.2 (175) 1800 600 21 (46.3) 23.2 (51.2)
A37-∗-R-07-∗-K-32∗ 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 1.2 (175) 1800 600 29 (63.9) 33.3 (73.4)
A56-∗-R-07-∗-K-32∗ 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 1.2 (175) 1800 600 36 (79.4) 40.3 (88.9)
A70-∗R07S-60∗ 70.0 (4.27) 30 (1.83) 25 (3630) 25 (3630) 2 (290) 1800 600 60.3 (133) 72.3 (159)
A90-∗R07S-60∗ 91.0 (5.55) 56 (3.42) 25 (3630) 25 (3630) 2 (290) 1800 600 77.5 (171) 98 (216)
A145-∗R07S-60∗ 145 (8.85) 83 (5.06) 25 (3630) 25 (3630) 2 (290) 1800 600 94 (207) 119 (262)
1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.
2. When operating the pump exceeding the rated pressure, operating conditions are restricted.
Refer to page 6 for the details.
No.58
"A" Series Piston Pumps
Pilot Pressure Control Type Pressure Compensator
A10 / A16 / A22 / A37 / A56 / A70 / A90 / A145
PISTON
PUMPS
A
Model Number Designation
A56
32
(56.2 cm3/rev)
A70 -F R 07 S -60 ∗
Direction of Design Design
Series Number Mounting Control Type Port Position
Rotation Number Std.
A10 F: 3 Viewed from 12
(10.0 cm3/rev) Flange Mtg.
Shaft End
A70 07:
60
(70 cm3/rev) F: Pilot Pressure 4
R: Control Type Refer to
A90 Flange Mtg. 1 S:
Clockwise Pressure 60
(91.0 cm3/rev) L: Compensator Side Port
(Normal)
A145 Foot Mtg.
60
(145 cm3/rev)
1. Available to supply pump with anti-clockwise rotation. Consult 2. The axial port is not available to the N.American Design Standard of
Yuken for details. A37 and A56.
3. When A10 pump is used as the foot Mtg., order the Mtg. Bracket kit 4. Design Standards: None ........... Japanese Standard "JIS"
shown below separately. Refer to page 17 for dimensions of the Mtg. 80 ............... European Design Standard
bracket. 90 ............... N. American Design Standard
Performance Characteristics
For performance characteristics, refer to models of pressure compensator type on page 10 to 16.
Pipe Flange Kit
For pipe flange, refer to form of pressure compensator type on page 7.
No.59
"A" Series Piston Pumps
A10-FR07 PISTON
Installation Drawing
PUMPS
Filling Port 1
[22(.87) Hex. Head Plug Furnished]
3
Drain Port "E" Thd.
Pilot Port "PP"
"D" Thd. Fully Extended
Fully Extended 180(7.09)
96.5(3.80) 170 44.5(1.75)
Safety Valve
Pressure Adj. Screw (6.69)
3(.12) Hex. Soc. 33(1.30) 90.5 6.5(.26)
(3.56)
INC. 52.5 25 4.79(.1886)
Flow Adj. Screw (2.07) (.98)
4.76(.1874)
(4.21)
13(.51) Hex.
107
(3.62)
(2.56)
92
(1.61)
(6.73)
65
171
41
DEC.
(.43)
11
82.50(3.248) Dia.
19.02(.7488) Dia.
2 3 10.5
19.05(.7500)
82.55(3.250)
21.24(.836)
21.08(.830)
Suction Port 25 25 106
(.41) 93 (3.66)
"C" Thd. (4.17)
(.98) (.98) 131 Dia.
64.5 64.5 (5.16) 130
(2.54) (2.54) 156 (5.12)
2 3
Discharge Port (6.14)
"C" Thd. 159.5
(6.28)
1. Install the pump so that the "Filling Port" is at the top. 3. As the tightening torques of suction, discharge and drain port fittings,
2. Use either port of two suction and outlet ports at your option. Keep the conform to the below.
remaining ports plugged.
Port Tightening Torque
Suction Port 65 - 75 Nm
Model Numbers "C" Thd. "D" Thd. "E" Thd. Discharge Port (575 - 664 IN. lbs)
A10-FR07-12 Rc 1/2 Rc 1/4 Rc 3/8
40 - 50 Nm
A10-FR07-1280 1/2 BSP.F 1/4 BSP.Tr 3/8 BSP.F Drain Port
(354 - 443 IN. lbs)
A10-FR07-1290 1/2 NPT 1/4 NPT 3/8 NPT
DIMENSIONS IN
MILLIMETRES (INCHES)
No.60
"A" Series Piston Pumps
A16 / A22-F-R-07 PISTON
PUMPS
A
Installation Drawing
(3.78)
109
(3.25)
96
82.5
(2.44)
62
(7.36)
187
(.71)
(.47)
18
12
X
82.50(3.248) Dia.
19.02(.7488) Dia.
R12
19.05(.7500)
82.55(3.250)
(R.47)
21.24(.836)
21.08(.830)
95(3.74) Dia.
12 106
(.47) (4.17)
172 130
(6.77) (5.12)
188
(7.40)
INC.
(2.56)
2. Use either port of two pilot ports at your option. Keep the remaining
(1.874)
47.6
port plugged.
22.2
Suction Port (.874) "F" Thd. 17(.67) Deep
19(.75) Dia. 65 8 Places
(2.56) Discharge Port
19(.75) Dia.
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd.
A16/A22-F-R-07-K-32 Rc 3/8 Rc 3/8 Rc 1/4
M10
A16/A22-F-R-07-K-3280 3/8 BSP. F 3/8 BSP. F 1/4 BSP. Tr
A16/A22-F-R-07-K-3290 3/8 NPT 3/8 NPT 1/4 NPT 3/8-16 UNC
DIMENSIONS IN
MILLIMETRES (INCHES)
No.61
"A" Series Piston Pumps
A37-F-R-07 PISTON
Installation Drawing
PUMPS
Side Port Type
6.38(.2512)
32(1.26) 6.35(.2500)
(4.41)
(4.13)
(3.48)
112
105
88.5
(2.68)
68
(7.95)
(2.311)
202
X
58.2
(.55)
(.98)
14
25
101.55(3.998) Dia.
22.20(.8740) Dia.
R14
101.60(4.000) 120(4.72) Dia. (R.55)
22.23(.8752)
port plugged.
71
86 86
(3.39) (3.39)
Surface of Surface of
Suction Port Discharge Port
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A37-F-R-07-S-K-32 Rc 1/2 Rc 3/8 Rc 1/4
M10 19 (.75)
A37-F-R-07-S-K-3280 1/2 BSP.F 3/8 BSP.F 1/4 BSP. Tr
A37-F-R-07-S-K-3290 1/2 NPT 3/8 NPT 1/4 NPT 7/16-14 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
No.62
"A" Series Piston Pumps
A56-F-R-07 PISTON
PUMPS
A
Installation Drawing
7.97(.3138)
40(1.57)
7.94(.3126)
(5.43)
138
(3.84)
(3.54)
97.5
(3.03)
90
77
(9.29)
236
X
(2.311)
(.55)
58.7
(.98)
14
25
101.55(3.998) Dia.
31.70(1.248) Dia.
R14
(R.55)
101.60(4.000)
31.75(1.250)
35.32(1.391)
35.14(1.383)
100 100
(3.94) (3.94)
Surface of Suction Port Surface of Discharge Port
View Arrow X
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A56-F-R-07-S-K-32 Rc 3/4 Rc 3/8 Rc 1/4
M10 19 (.75)
A56-F-R-07-S-K-3280 3/4 BSP.F 3/8 BSP.F 1/4 BSP. Tr
A56-F-R-07-S-K-3290 3/4 NPT 3/8 NPT 1/4 NPT 7/16-14 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
No.63
"A" Series Piston Pumps
A70-FR07S PISTON
Installation Drawing
PUMPS
Flange Mtg. : A70-FR07S-60/6080/6090
2
Drain Port 95 95
Surface of Surface of
"C" Thd. Discharge Port (3.74) (3.74) Suction Port
Fully Extended 62 (Both Sides) 73 73
351.5(13.84) (2.44) Surface of Surface of
Drain Port (2.87) (2.87) Drain Port
65 13
(2.56) 27(1.06) Dia. Spotface
4 Places (.51)
9.5
(From Rear)
(.37)
40 7.97(.3138)
14(.55)
(1.57) 7.94(.3126)
(7.11)
(7.17)
180.5
182
X Y
(3.54)
(.71)
90
18
(4.508)
(2.063)
(7.09)
114.4
52.4
180
(4.65)
118
126.95(4.998) Dia.
Discharge Port
31.70(1.248) Dia.
35.32(1.391)
35.14(1.383)
Surface of
Pilot Port "PP1"
2
Pilot Port "PP2"
316.5 "F" Thd.
(14.46)
244
Eye Bolt (9.61)
M10
1
22(.87) Filling Port
2 [22(.87) Hex. Head Plug Furnished]
Pilot Port "PP1" Safety Valve Pres.
"F" Thd. Adj. Screw
(6.52)
165.5
14(.55) Hex.
INC.
(2.752)
69.9
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A70-FR07S-60 Rc 3/4 Rc 1/4
M12 M10 19 (.75)
A70-FR07S-6080 3/4 BSP.F 1/4 BSP. Tr
A70-FR07S-6090 3/4 NPT 1/2-13 UNC 3/8-16 UNC 1/4 NPT 21 (.83)
DIMENSIONS IN
MILLIMETRES (INCHES)
No.64
"A" Series Piston Pumps
A90-FR07S PISTON
PUMPS
A
Installation Drawing
2
Drain Port
"C" Thd.
(Both Sides) Surface of Surface of
95 Discharge Port Suction Port
(3.74) 105 105
119.5 23(.91) (4.13) (4.13)
(4.70) 68 68
13(.51) Surface of Surface of
Drain Port (2.68) (2.68) Drain Port
63(2.48)
(7.48)
(7.50)
190.5
190
X 9.56(.3764) Y
(4.45)
113
9.53(.3752)
(6.362)
(2.311)
161.6
58.7
(5.00)
127
Discharge Port
152.35(5.998) Dia.
38.05(1.498) Dia.
32(1.26) Dia.
152.40(6.000)
38.10(1.500)
(6.69)
170
(.37) (.69) (3.46)
88
(3.063)
77.8
Suction Port
48(1.89) Dia.
42.9
View Arrow X (1.689)
270
"D" Thd. "H" Deep
(10.63)
4 Places
View Arrow Y
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. H mm (IN.) J mm (IN.)
A90-FR07S-60 Rc 3/4 Rc 1/4
M12 M10 19 (.75) 19 (.75)
A90-FR07S-6080 3/4 BSP.F 1/4 BSP. Tr
A90-FR07S-6090 3/4 NPT 1/2-13 UNC 7/16-14 UNC 1/4 NPT 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mounting Type
Mounting bracket is common to that of pressure compensator model.
Refer to page 22 for the dimensions of mounting bracket.
No.65
"A" Series Piston Pumps
A145-FR07S PISTON
Installation Drawing
PUMPS
Flange Mtg. : A145-FR07S-60/6080/6090
Drain Port 2
"C" Thd.
(Both Sides) Surface of Surface of
Discharge Port Suction Port
112 112
Fully Extended 112 (4.41) (4.41)
400.5(15.77) (4.41) 72 72
89 23 Surface of Surface of
Drain Port (2.83) (2.83) Drain Port
(3.50) (.91) 15
13 (.59)
(.51)
70
(2.76)
(7.81)
198.5
X 11.14(.4386)
11.11(.4374)
(4.33)
110
Y
(9.000)
(2.311)
228.6
58.7
(5.55)
141
Discharge Port
152.35(5.998) Dia.
44.40(1.748) Dia.
32(1.26) Dia.
49.39(1.944)
49.21(1.937)
44.45(1.750)
152.40(6.000)
Surface of
Eye Bolt Pilot Port "PP1"
Safety Valve Pres. M10
362.5 2
Adj. Screw Pilot Port "PP2"
2
24 14(.55) Hex. (14.27) "F" Thd.
Pilot Port "PP1" INC.
(.94) 290
"F" Thd. Flow Adj. Screw
(11.42)
17(.67) Hex. 1
Filling Port
DEC. [27(1.06) Hex. Head Plug Furnished]
(6.97)
(7.56)
Suction Port
177
192
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. H mm (IN.) J mm (IN.)
A145-FR07S-60 Rc 3/4 Rc 1/4
M12 M10 19 (.75) 19 (.75)
A145-FR07S-6080 3/4 BSP.F 1/4 BSP. Tr
A145-FR07S-6090 3/4 NPT 1/2-13 UNC 7/16-14 UNC 1/4 NPT 21 (.83) 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
No.66
"A" Series Piston Pumps
Variable Displacement-Double Pumps PISTON A
Pressure Compensator Type PUMPS
Specifications
Graphic Symbol
M
O
Specifications
Shaft Speed
Geometric Min. Adj. Operating Pressure Approx. Mass
Range
Displacement Flow MPa (PSI) kg (lbs.)
Model Numbers r/min
cm3/rev cm3/rev
2 1 Flange Foot
(cu.in./rev) (cu.in./rev) Rated Intermittent Max. Min.
Mtg. Mtg.
3 Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 35.5 37.7
A1616-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) (98.3) (83.1)
3 Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 35.5 37.7
A1622-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) (98.3) (83.1)
3 Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 35.5 37.7
A2222-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) (98.3) (83.1)
3 Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 50 54.3
A1637-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) (110) (120)
3 Outboard Pump 22,2 (1.355) 6 (.366) 16 (2320) 16 (2320) 50 54.3
A2237-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) (110) (120)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 54.5 58.8
A1656-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) (120) (130)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 54.5 58.8
A2256-∗R01∗01∗∗K-32∗ 1800 600
Inboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) (120) (130)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 77.5 89.5
A1670-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 70.0 (4.27) 30 (1.831) 25 (3630) 28 (4060) (171) (197)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 77.5 89.5
A2270-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 70.0 (4.27) 30 (1.831) 25 (3630) 28 (4060) (171) (197)
3 Outboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 86.5 98.5
A3770-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 70.0 (4.27) 30 (1.831) 25 (3630) 28 (4060) (191) (217)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 88 108.5
A1690-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (194) (239)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 88 108.5
A2290-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (194) (239)
Outboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 100.5 121
A3790-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (222) (267)
Outboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 107.5 128
A5690-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 91.0 (5.55) 56 (3.42) 25 (3630) 28 (4060) (237) (282)
Outboard Pump 15.8 (.964) 4 (.244) 16 (2320) 21 (3050) 109 134
A16145-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (240) (295)
Outboard Pump 22.2 (1.355) 6 (.366) 16 (2320) 16 (2320) 109 134
A22145-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (240) (295)
3 Outboard Pump 36.9 (2.25) 10 (.610) 16 (2320) 21 (3050) 121.5 146.5
A37145-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (268) (323)
3 Outboard Pump 56.2 (3.43) 12 (.732) 16 (2320) 21 (3050) 128.5 153.5
A56145-∗R01∗01∗∗-60∗ 1800 600
Inboard Pump 145 (8.85) 83 (5.06) 25 (3630) 28 (4060) (283) (338)
1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.
2. When operating the pump exceeding the rated pressure, operating conditions are restricted.
Refer to the page 70 for the details.
3. The maximum input power of these pumps must be restricted, because of the shaft strength.
Refer to the page 70 for the details.
No.67
"A" Series Piston Pumps
Variable Displacement-Double Pumps PISTON
Pressure Compensator Type PUMPS
Model Number Designation
No.68
"A" Series Piston Pumps
Variable Displacement-Double Pumps PISTON A
Pressure Compensator Type PUMPS
Pipe Flange Kits
No.69
"A" Series Piston Pumps
Variable Displacement-Double Pumps PISTON
Pressure Compensator Type PUMPS
Instructions / Performance Characteristics
Instructions
When using at a higher pressure than the rated pressure One Cycle Time 21 MPa (3050 PSI)
1/5 of One Cycle 1
Max. 6s [28 MPa (4060 PSI)]
Care should be taken in cases of used at a higher pressure than the rated
pressure, because operating terms may be restricted. For example, if used
as per maximum illustrated operating conditions, intermittent time at Pressure
maximum flow is restricted to under 1/5 of one cycle time and under 6
seconds simultaneously. Conditions may vary according to the actual
working pressure and delivery (inclination angle of the swash plate).
Consult factory or Yuken sales representative for further information. Max.
Q1 × P1 + Q2 × P2 <
= LM Q1 × P1 + Q2 × P2 <
= LP
3
Q1 : Displacement (cm /rev) Q1 : Displacement (cu.in./rev)
Outboard Pump Outboard Pump
P1 : Discharge Pressure (MPa) P1 : Discharge Pressure (PSI)
Q2 : Displacement (cm3/rev) Q2 : Displacement (cu.in./rev)
Inboard Pump Inboard Pump
P2 : Discharge Pressure (PSI) P2 : Discharge Pressure (PSI)
LM : See the table below L P : See the table below
Model Numbers LM LP
A1616/A1622/A2222 523 4627
A1637/A2237 900 7963
A3770 2408 21305
A37145/A56145 4739 41930
Performance Characteristics
Refer to relevant the page for performance characteristics of single pumps excluding noise level characteristics.
Outboard Pump Inboard Pump
Model Numbers Reference Reference
Performance Characteristics Performance Characteristics
Page Page
A1616-∗R01∗01∗∗K-32∗ Same as Single Pump "A16" 10 Same as Single Pump "A16" 10
A1622-∗R01∗01∗∗K-32∗ Same as Single Pump "A16" 10
Same as Single Pump "A22" 11
A2222-∗R01∗01∗∗K-32∗ Same as Single Pump "A22" 11
A1637-∗R01∗01∗∗K-32∗ Same as Single Pump "A16" 10
Same as Single Pump "A37" 12
A2237-∗R01∗01∗∗K-32∗ Same as Single Pump "A22" 11
A1656-∗R01∗01∗∗K-32∗ Same as Single Pump "A16" 10
Same as Single Pump "A56" 13
A2256-∗R01∗01∗∗K-32∗ Same as Single Pump "A22" 11
A1670-∗R01∗01∗∗-60∗ Same as Single Pump "A16" 10
A2270-∗R01∗01∗∗-60∗ Same as Single Pump "A22" 11 Same as Single Pump "A70" 14
A3770-∗R01∗01∗∗-60∗ Same as Single Pump "A37" 12
A1690-∗R01∗01∗∗-60∗ Same as Single Pump "A16" 10
A2290-∗R01∗01∗∗-60∗ Same as Single Pump "A22" 11
Same as Single Pump "A90" 15
A3790-∗R01∗01∗∗-60∗ Same as Single Pump "A37" 12
A5690-∗R01∗01∗∗-60∗ Same as Single Pump "A56" 13
A16145-∗R01∗01∗∗-60∗ Same as Single Pump "A16" 10
A22145-∗R01∗01∗∗-60∗ Same as Single Pump "A22" 11
Same as Single Pump "A145" 16
A37145-∗R01∗01∗∗-60∗ Same as Single Pump "A37" 12
A56145-∗R01∗01∗∗-60∗ Same as Single Pump "A56" 13
No.70
"A" Series Piston Pumps
A1616 / A1622 / A2222-∗R01∗01∗ PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A1616-FR01∗01∗K-32/3280/3290
A1622-FR01∗01∗K-32/3280/3290
A2222-FR01∗01∗K-32/3280/3290
Fully Extended 44.5
448.5 (1.75)
(17.66)
288.5 6.5(.26)
(11.36)
256
1 (10.08)
Filling Port 59(2.32)
[22(.87) Hex. Head Plug Furnished] Drain Port "C" Thd.
26.5
(1.04)
4.79(.1886)
Y 25(.98) 4.76(.1874)
(4.29)
(3.78)
(3.78)
109
96
(2.44)
96
47.6(1.874)
62
(7.36)
12(.47)
187
(.71)
X
18
82.50(3.248) Dia.
19.02(.7488) Dia.
R12
95(3.74) Dia. (R.47)
19.05(.7500)
82.55(3.250)
21.24(.836)
21.08(.830)
Outboard Pump 22.2 12 106
(.874) (.47) (4.17)
150.5 130
(5.93) (5.12)
401.5 74 74
(15.81)
Inboard Pump (2.91) (2.91)
"D" Thd. 17(.67) Deep Surface of Discharge Port Surface of Suction Port
Discharge Port 19 (.75) Dia. 188
4 Places (Both Sides)
Rear Side (7.40)
Suction Port 19 (.75) Dia.
16 16
Flow Adj. Screw (.63) (.63) Pressure Adj. Screw 16 16
17(.67) Hex. 17(.67) Hex. INC. (.63) (.63)
Flow Adj. Screw Pressure Adj. Screw
DEC. 17(.67) Hex. 17(.67) Hex.
DEC. INC.
(1.874)
47.6
View Arrow Y
"D" Thd. 17(.67) Deep
22.2 8 Places
Suction Port (.874)
19(.75) Dia. 65 Discharge Port
19 (.75) Dia.
(2.56)
View Arrow X
1. Install the pump so that the "Filling Port" is at the top.
Model Numbers "C" Thd. "D" Thd.
A1616/A1622/A2222-FR01∗01∗K-32 Rc 3/8
M10
A1616/A1622/A2222-FR01∗01∗K-3280 3/8 BSP. F
A1616/A1622/A2222-FR01∗01∗K-3290 3/8 NPT 3/8-16 UNC
DIMENSIONS IN
Foot Mtg. : A1616-LR01∗01∗K-32/3280/3290 MILLIMETRES (INCHES)
A1622-LR01∗01∗K-32/3280/3290 12(.47) Dia. Through
A2222-LR01∗01∗K-32/3280/3290 24(.94) Dia. Spotface
4 Places
(3.15)
(.59)
(.55)
15
3(.12)
14
80
50 56.5 95
(3.74)
(1.969) (2.22)
95 27.5 72.5 72.5
(3.74) (1.08) (2.854) (2.854)
180
(7.09)
For other dimensions, refer to "Flange Mtg.".
No.71
"A" Series Piston Pumps
A1637 / A2237-∗R01∗01∗ PISTON
Installation Drawing
PUMPS
Flange Mtg. : A1637-FR01∗01∗K-32/3280/3290
A2237-FR01∗01∗K-32/3280/3290
Fully Extended
471.5 62(2.44)
(18.56)
311.5 9.5(.37)
(12.26)
Drain Port "D" Thd. 279
1
(10.98) Filling Port
77 [22(.87) Hex. Head Plug Furnished]
(3.03) 202
1 30 (7.95)
Filling Port
(2.311)
58.7
[22(.87) Hex. Head Plug Furnished] (1.18) 174
Drain Port "C" Thd. (6.85)
7.97(.3138)
40 7.94(.3126)
Y
(4.29)
(4.41)
(4.13)
(3.78)
(1.57)
109
112
105
96
(2.44)
62
(7.95)
202
(.98)
(.55)
X
25
14
(3.07)
78
101.55(3.998) Dia.
31.70(1.248) Dia.
R14
120(4.72) Dia. (R.55)
101.60(4.000)
31.75(1.250)
35.32(1.391)
35.14(1.383)
Outboard Pump 30.2 12 146
(1.189) (.47) (5.75)
178.5 86 86
(7.03) (3.39) (3.39)
Surface of Surface of
424.5
Discharge Port Suction Port
(16.71) Inboard Pump
"E" Thd. "H" Deep Discharge Port 32 (1.26) Dia.
4 Places (Both Sides) Rear Side
Suction Port 32 (1.26) Dia.
16 16
Flow Adj. Screw (.63) (.63) Pressure Adj. Screw
17(.67) Hex. 17(.67) Hex.
INC.
DEC. 13 19
Flow Adj. Screw (.51) (.75)
17(.67) Hex. Pressure Adj. Screw
17(.67) Hex.
(1.874)
47.6
DEC. INC.
View Arrow X
1. Install the pump so that the "Filling Port" is at the top.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A1637/A2237-FR01∗01∗K-32 Rc 1/2 Rc 3/8
M10 M10 19 (.75)
A1637/A2237-FR01∗01∗K-3280 1/2 BSP.F 3/8 BSP.F
A1637/A2237-FR01∗01∗K-3290 1/2 NPT 3/8 NPT 7/16-14 UNC 3/8-16 UNC 20 (.79)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A1637-LR01∗01∗K-32/3280/3290
A2237-LR01∗01∗K-32/3280/3290
14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.59)
(.55)
102
3(.12)
15
14
60 77 120
(2.362)(3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
No.72
"A" Series Piston Pumps
A1656 / A2256-∗R01∗01∗ PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A1656-FR01∗01∗K-32/3280/3290
A2256-FR01∗01∗K-32/3280/3290
62
Fully Extended (2.44)
484(19.06)
324 9.5
(12.76) (.37)
Drain Port "D" Thd.
291.5
(11.48) Filling Port
1
50.5(1.99)
58.7(2.311)
1 [22(.87) Hex. Head Plug Furnished] Surface of
Filling Port 2 Drain Port
[22(.87) Hex. Head Plug Furnished] 43.5(1.71) Drain Port
"C" Thd. 41 49
(1.61) (1.93)
40
7.97(.3138)
(1.57)
(5.43)
7.94(.3126)
Y
(4.29)
138
(3.78)
(3.54)
109
96
90
(9.29)
236
(.98)
(.55)
X
25
14
(2.44)
(3.07)
62
78
31.70(1.248) Dia.
101.55(3.998) Dia.
35.32(1.391)
35.14(1.383)
101.60(4.000)
31.75(1.250)
R14
30.2 12 146 (R.55)
Outboard Pump (1.189) (.47) (5.75)
120(4.72) Dia.
191 174
(7.52) (6.85)
437 100 100
(17.20) Inboard Pump (3.94) (3.94)
"E" Thd. "H" Deep Discharge Port 30 (1.18) Dia. Surface of 232 Surface of
4 Places (Both Sides) Rear Side Discharge Port (9.13) Suction Port
Suction Port 35 (1.38) Dia.
16 16
(.63) (.63)
DEC.
47.6
INC.
DEC.
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd. "H" mm (IN.)
A1656/A2256-FR01∗01∗K-32 Rc 3/4 Rc 3/8
M10 M10 19 (.75)
A1656/A2256-FR01∗01∗K-3280 3/4 BSP.F 3/8 BSP.F
A1656/A2256-FR01∗01∗K-3290 3/4 NPT 3/8 NPT 7/16-14 UNC 3/8-16 UNC 20 (.79)
DIMENSIONS IN
Foot Mtg. : A1656-LR01∗01∗K-32/3280/3290 MILLIMETRES (INCHES)
A2256-LR01∗01∗K-32/3280/3290
(.59)
3(.12)
102
14
15
60 77 120
(2.362) (3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
No.73
"A" Series Piston Pumps
A1670 / A2270 / A3770-∗R01∗01∗ PISTON
Installation Drawing
PUMPS
Flange Mtg. : A1670-FR01∗01∗S-60/6080/6090
A2270-FR01∗01∗S-60/6080/6090 DIMENSIONS IN
A3770-FR01∗01∗S-60/6080/6090 MILLIMETRES (INCHES)
62
Fully Extended (2.44)
E Surface of Discharge Port Surface of Suction Port
95 95
19.5(.77)
F (3.74) (3.74)
Drain Port 9.5(.37) Surface of Drain Port Surface of Drain Port
H 73 73
"b" Thd. 65 Drain Port 2 7.97(.3138)
(2.063)
1 (2.56) "a" Thd. (Both Sides) (2.87) (2.87) 7.94(.3126)
52.4
Filling Port 27(1.06) Dia.
40 Spotface
[22(.87) Hex. Head Plug Furnished]
(1.57) (From Rear)
(.55)
(7.17)
14
182
4 Places
(3.54)
90
(4.504)
X Y
(7.09)
114.4
(.71)
180
18
Q
(4.65)
118
Discharge Port
31.70(1.248) Dia.
126.95(4.998) Dia.
"S" Dia. 35(1.38) Dia.
Spotface
35.32(1.391)
35.14(1.383)
127.00(5.000)
31.75(1.250)
"f" Thd. "j" Deep P 16 (From Rear)
26.2 (.63) 114.4
4 Places 2 Places
(1.031) 18 (4.504)
Inboard Pump 134
(.71)
246.5 (5.28)
Discharge Port
(9.70) 181
26 (1.02) Dia.
(7.126)
J 211
"e" Thd. 17(.67) Deep Outboard Pump (8.31)
4 Places
38 (1.50) Dia.
DEC.
Flow Adj. Screw Pres. Adj. Screw Z Pres. Adj. Screw
17(.67) Hex. 17(.67) Hex. 17(.67) Hex.
DEC. INC. INC.
K
Q
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports of inboard pump at your option. Keep the remaining port plugged. Note that on the European design standard
(6080 Design), only the left side, as viewed from the shaft end, of the drain port of inboard pump is machined.
3. Case drain port is available for use when draining hydraulic fluid from pump casing.
Dimensions mm (Inches)
Model Numbers
E F H J K L N P Q S
A1670-∗R01∗01∗S-60∗ 524.5 364.5 332 456 96 188 74 22.2 47.6 19
A2270-∗R01∗01∗S-60∗ (20.65) (14.35) (13.07) (17.95) (3.78) (7.40) (2.91) (.874) (1.874) (.75)
A3770-∗R01∗01∗S-60∗
552.5 382.5 335.5 484 105 202 86 30.2 58.7 32
(20.65) (15.06) (13.21) (19.06) (4.13) (7.95) (3.39) (1.189) (1.311) (1.26)
No.74
"A" Series Piston Pumps
A1690 / A2290 / A3790-∗R01∗01∗ PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A1690-FR01∗01∗S-60/6080/6090
A2290-FR01∗01∗S-60/6080/6090 DIMENSIONS IN
A3790-FR01∗01∗S-60/6080/6090 MILLIMETRES (INCHES)
95
Fully Extended (3.74)
E
Surface of Surface of
23(.91) Discharge Port Suction Port
F 105 105
13(.51) (4.13) (4.13)
Drain Port "b" Thd. H
2 Surface of Surface of
119.5 Drain Port Drain Port Drain Port
68 68
(2.311) (4.70) "a" Thd. (Both Sides)
(2.68) (2.68)
58.7
1
Filling Port 63
[22(.87) Hex. Head Plug Furnished] (2.48)
9.56
(7.50)
190.5
9.53
(4.45)
113
(.3764)
(6.362)
X (.3752)
161.6
Y
Q
(5.00)
127
Discharge Port
152.35(5.998) Dia.
38.05(1.498) Dia.
"S" Dia.
P
38.10(1.500)
42.36(1.668)
42.18(1.661)
"f" Thd. "j" Deep 30.2
22 152.40(6.000) 161.6
4 Places (.87) R22(R.87)
(1.189) (6.362)
Outboard Pump 23
(.91) 21.5(.85) Dia. Through
"e" Thd. "h" Deep 270 39(1.54) Dia. Spotface
4 Places (10.63) (From Rear)
Inboard Pump 4 Places
J
Discharge Port Case Drain Port 3
32 (1.26) Dia. 5 (.20) Hex. Soc.
INC. INC.
Q
View Arrow Z
Suction Port
N N P "S" Dia.
42.9 "f" Thd. "j" Deep
(1.689) 4 Places
Surface of Surface of
Suction Port L Discharge Port 270 "d" Thd. "h" Deep
(10.63) 4 Places
View Arrow X J
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports of inboard pump at your option. Keep the remaining port plugged. Note that on the European design standard
(6080 Design), only the left side, as viewed from the shaft end, of the drain port of inboard pump is machined.
3. Case drain port is available for use when draining hydraulic fluid from pump casing.
Dimensions mm (Inches)
Model Numbers
E F H J K L N P Q S
A1690-∗R01∗01∗S-60∗ 543 383 350.5 474.5 96 188 74 22.2 47.6 19
A2290-∗R01∗01∗S-60∗ (21.38) (15.08) (13.80) (18.68) (3.78) (7.40) (2.91) (.874) (1.874) (.75)
A3790-∗R01∗01∗S-60∗
571 401 354 502.5 105 202 86 30.2 58.7 32
(22.48) (15.79) (13.94) (19.78) (4.13) (7.95) (3.39) (1.189) (1.311) (1.26)
No.75
"A" Series Piston Pumps
A5690-∗R01∗01∗ PISTON
Installation Drawing
PUMPS
Flange Mtg. : A5690-FR01∗01∗S-60/6080/6090
DIMENSIONS IN
MILLIMETRES (INCHES)
Discharge Port
32 (1.26) Dia. 95
Fully Extended (3.74)
583.5(22.98) Surface of Surface of
374.5 23(.91) Discharge Port Suction Port
105 105
1 (14.74)
Filling Port 13(.51) (4.13) (4.13)
367.5
[22(.87) Hex. Head Plug Furnished] Surface of
2 (14.47) 2 Surface of
Drain Port 119.5 Drain Port Drain Port 68 68 Drain Port
"D" Thd. (Both Sides) (4.70) "C" Thd. (Both Sides)
(2.311) (2.68) (2.68)
58.7
Outboard Pump 63
(2.48)
9.56
(7.50)
190.5
9.53
(4.45)
(.3764)
113
(2.311)
(6.362)
X (.3752)
161.6
Y
58.7
(5.00)
127
38.05(1.498) Dia.
152.35(5.998) Dia.
Discharge Port
30 (1.18) Dia.
42.36(1.668)
42.18(1.661)
38.10(1.500)
30.2
152.40(6.000)
22
"F" Thd. "J" Deep (1.189) 30.2 161.6 R22(R.87)
(.87)
4 Places (1.189) (6.362)
23
"F" Thd. "H" Deep (.91) 21.5(.85) Dia. Through
4 Places 270 39(1.54) Dia. Spotface
(10.63) (From Rear)
Inboard Pump 4 Places
515
(20.28) 3
Case Drain Port
5 (.20) Hex. Soc.
Suction Port
Pres. Adj. Screw
77.8
48(1.89) Dia.
17(.67) Hex.
Flow Adj. Screw Pres. Adj. Screw Z
17(.67) Hex. 17(.67) Hex. INC.
DEC. INC.
(3.54)
58.7(2.311)
90
View Arrow Z
Suction Port
35(1.38) Dia.
100 100 30.2
(3.94) (3.94) 42.9 (1.189) "F" Thd. "J" Deep
(1.689) 4 Places
Surface of Surface of
232 Discharge Port 270 "E" Thd. "H" Deep
Suction Port
(9.13) (10.63) 4 Places
515
View Arrow X (20.28)
View Arrow Y
No.76
"A" Series Piston Pumps
A16145 / A22145 / A37145-∗R01∗01∗ PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A16145-FR01∗01∗S-60/6080/6090
A22145-FR01∗01∗S-60/6080/6090 DIMENSIONS IN
A37145-FR01∗01∗S-60/6080/6090 MILLIMETRES (INCHES)
112
Fully Extended (4.41) 143
E (5.63)
Surface of Surface of
23(.91) Discharge Port Suction Port
F 112 112
(4.41) (4.41)
Drain Port 13(.51) 2
Surface of Surface of
"b" Thd. H Drain Port Drain Port 72 72 Drain Port
"a" Thd. (Both Sides)
89
(2.311)
58.7 (2.83) (2.83)
1
Filling Port (3.50) 70
[22(.87) Hex. Head Plug Furnished] (2.76)
11.14
(7.81)
198.5
11.11
(4.33)
(.4386) Y
110
(9.000)
X (.4374)
228.6
Q
(5.55)
141
Discharge Port
152.35(5.998) Dia.
Dia.
"S" Dia.
P
"f" Thd. "j" Deep
44.45(1.750)
152.40(6.000)
44.40(1.748)
49.39(1.944)
4 Places 30.2 24 49.21(1.937) 228.6 R22(.87)
Outboard Pump (1.189) (.94) (9.000)
26 273
"e" Thd. "j" Deep
4 Places (1.02) (10.75)
299.5 21.5(.85) Dia. Through
Discharge Port
(11.79) 39(1.54) Dia. Spotface
32 (1.26) Dia. Inboard Pump (From Rear)
J 3 4 Places
Case Drain Port Eye Bolt M10
5 (.20) Hex. Soc.
Pres. Adj. Screw
(3.063)
1
77.8
K
DEC.
Q
DEC. INC.
Suction Port
N N P "S" Dia.
42.9 "f" Thd. "j" Deep
4 Places
Surface of Surface of (1.689)
Suction Port 299.5 "d" Thd. "h" Deep
L Discharge Port
4 Places
(11.79) Suction Port
J 48(1.89) Thd.
View Arrow X View Arrow Y
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports of inboard pump at your option. Keep the remaining port plugged. Note that on the European design standard
(6080 Design), only the left side, as viewed from the shaft end, of the drain port of inboard pump is machined.
3. Case drain port is available for use when draining hydraulic fluid from pump casing.
Dimensions mm (Inches)
Model Numbers
E F H J K L N P Q S
A16145-∗R01∗01∗S-60∗ 576.5 416.5 384 508 96 188 74 22.2 47.6 19
A22145-∗R01∗01∗S-60∗ (22.70) (16.40) (15.12) (20.00) (3.78) (7.40) (2.91) (.874) (1.874) (.75)
A37145-∗R01∗01∗S-60∗
604.5 434.5 387.5 536 105 202 86 30.2 58.7 32
(23.80) (17.11) (15.26) (21.10) (4.13) (7.95) (3.39) (1.189) (1.311) (1.26)
No.77
"A" Series Piston Pumps
A56145-∗R01∗01∗ PISTON
Installation Drawing
PUMPS
Flange Mtg. : A56145-FR01∗01∗S-60/6080/6090
DIMENSIONS IN
MILLIMETRES (INCHES)
143
112
Fully Extended (4.41) (5.63)
617(24.29) Surface of Surface of
408 23(.91) Discharge Port 112 112 Suction Port
1 (16.06) (4.41) (4.41)
Filling Port 401 13(.51)
[22(.87) Hex. Head Plug Furnished] Drain Port 2 Surface of Surface of
(15.79)
2 "C" Thd. (Both Sides) Drain Port Drain Port
Drain Port 89 72 72
"D" Thd. (Both Sides)
(2.311)
(3.50) (2.83) (2.83)
58.7
Outboard Pump 70
(2.76)
11.14
(7.81)
198.5
11.11
(4.33)
110
(.4386)
Y
(2.311)
(9.000)
(.4374)
228.6
58.7
(5.55)
141
152.35(5.998) Dia.
Discharge Port Dia.
30 (1.18) Dia.
152.40(6.000)
30.2
44.45(1.750)
49.39(1.944)
49.21(1.937)
44.40(1.748)
DEC.
77.8
DEC. INC.
Suction Port
100 100 30.2 35(1.38) Dia.
(3.94) (3.94) 42.9 (1.189) "E" Thd. "H" Deep
Surface of Surface of (1.689) 4 Places
232 299.5 "d" Thd. "h" Deep
Suction Port Discharge Port
(9.13) (11.79) 4 Places
548.5
View Arrow X (21.59)
Suction Port
48(1.89) Dia.
View Arrow Y
No.78
"A" Series Piston Pumps
Double Pumps
Spare Parts List
PISTON
PUMPS
A
A1616-∗R01∗01∗∗K-32/3280/3290
A∗∗22-∗R01∗01∗∗K-32/3280/3290 CAUTION
A∗∗37-∗R01∗01∗∗K-32/3280/3290 When making replacement of seals or bearings,
A∗∗56-∗R01∗01∗∗K-32/3280/3290 please do it carefully after reading through the
A∗∗70-∗R01∗01∗∗-60/6080/6090 relevant instructions in the Operator's Manual.
A∗∗90-∗R01∗01∗∗-60/6080/6090
A∗∗145-∗R01∗01∗∗-60/6080/6090
83 82 80 81
Outboard Pump
Inboard Pump
Seals
Seal KIt Numbers Item 80 O-Ring
Pump Model Numbers
Complete Kit For Outboard Pump For Inboard Pump Part Numbers Qty.
A1616-∗R01∗01∗∗K-32∗
A1622-∗R01∗01∗∗K-32∗ KS-A1616-0101-32 KS-A16-01-32 KS-A16-01-32 S85(NBR,Hs70) 1
A2222-∗R01∗01∗∗K-32∗
A1637-∗R01∗01∗∗K-32∗
KS-A1637-0101-32 KS-A16-01-32 KS-A37-01-32 S85(NBR,Hs70) 1
A2237-∗R01∗01∗∗K-32∗
A1656-∗R01∗01∗∗K-32∗
KS-A1656-0101-32 KS-A16-01-32 KS-A56-01-32 S85(NBR,Hs70) 1
A2256-∗R01∗01∗∗K-32∗
A1670-∗R01∗01∗∗-60∗
KS-A1670-0101-60 KS-A16-01-32 S85(NBR,Hs70) 1
A2270-∗R01∗01∗∗-60∗ KS-A70-01-60
A3770-∗R01∗01∗∗-60∗ KS-A3770-0101-60 KS-A37-01-32 S105(NBR,Hs70) 1
A1690-∗R01∗01∗∗-60∗
KS-A1690-0101-60 KS-A16-01-32 S85(NBR,Hs70) 1
A2290-∗R01∗01∗∗-60∗
A3790-∗R01∗01∗∗-60∗ KS-A3790-0101-60 KS-A37-01-32 KS-A90-01-60
S105(NBR,Hs70) 1
A5690-∗R01∗01∗∗-60∗ KS-A5690-0101-60 KS-A56-01-32
A16145-∗R01∗01∗∗-60∗
KS-A16145-0101-60 KS-A16-01-32 S85(NBR,Hs70) 1
A22145-∗R01∗01∗∗-60∗
A37145-∗R01∗01∗∗-60∗ KS-A37145-0101-60 KS-A37-01-32 KS-A145-01-60
S105(NBR,Hs70) 1
A56145-∗R01∗01∗∗-60∗ KS-A56145-0101-60 KS-A56-01-32
Notes :1 When ordering seals, please specify the seal kit number from the table above.
2 Complete seal kit consists of a seal kit for inboard pump, a seal kit for outboard pump and a piece of O-ring for item 80.
3 Seal kit and bearings for inboard pump and outboard pump are same as those for "A" series single pump. For details,
please refer to the table below and see the chart on the page relevant to pump model number concerned.
No.79
"A" Series Piston Pumps
Variable/Fixed Double Pumps PISTON
A16R1 / A22R1 / A37R1 / A56R1 / A70R1 / A90R1 / A145R1 PUMPS
Model Number Designation
Graphic Symbol
M
O
1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.
2. Design Standards: None ........... Japanese Standard "JIS"
80 ............... European Design Standard
90 ............... N. American Design Standard
No.80
"A" Series Piston Pumps
Variable / Fixed Double Pumps
Specifications
PISTON
PUMPS
A
Specifications
Shaft Speed
Geometric Operating Pressure Approx. Mass
Range
Displacement MPa (PSI) kg (lbs.)
Model Numbers r/min
cm3/rev
2 1 Flange Foot
(cu.in./rev) Rated Intermittent Max. Min.
Mtg. Mtg.
3 Outboard Pump Refer to the following page 28.8 31.0
A16R1-∗R01∗-∗AAK-32∗ 1800 750
Inboard Pump 15.8 (.964) 16 (2320) 21 (3050) (63.5) (68.4)
3 Outboard Pump Refer to the following page 28.8 31.0
A22R1-∗R01∗-∗AAK-32∗ 1800 750
Inboard Pump 22.2 (1.355) 16 (2320) 16 (2320) (63.5) (68.4)
3 Outboard Pump Refer to the following page 39 43.3
A37R1-∗R01∗-∗AAK-32∗ 1800 750
Inboard Pump 36.9 (2.25) 16 (2320) 21 (3050) (86.0) (95.5)
Outboard Pump Refer to the following page 47 51.3
A56R1-∗R01∗-∗AAK-32∗ 1800 750
Inboard Pump 56.2 (3.43) 16 (2320) 21 (3050) (104) (113)
Outboard Pump Refer to the following page 66 78
A70R1-∗R01∗-∗AA-60∗
3
1800 750
Inboard Pump 70.0 (4.27) 25 (3630) 28 (4060) (146) (172)
Outboard Pump Refer to the following page 82 105
A90R1-∗R01∗-∗AA-60∗
3
1800 750
Inboard Pump 91.0 (5.55) 25 (3630) 28 (4060) (181) (232)
Outboard Pump Refer to the following page 102 129
A145R1-∗R01∗-∗AA-60∗
3
1800 750
Inboard Pump 145 (8.85) 25 (3630) 28 (4060) (225) (284)
Outboard Pump Refer to the following page 72.5 84.5
A70R2-∗R01∗-∗AA-60∗
3
1800 600
Inboard Pump 70.0 (4.27) 25 (3630) 28 (4060) (160) (186)
Outboard Pump Refer to the following page 91.5 112
A90R2-∗R01∗-∗AA-60∗
3
1800 600
Inboard Pump 91.0 (5.55) 25 (3630) 28 (4060) (202) (247)
Outboard Pump Refer to the following page 112 137
A145R2-∗R01∗-∗AA-60∗
3
1800 600
Inboard Pump 145 (8.85) 25 (3630) 28 (4060) (247) (302)
1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.
2. Care should be taken in cases of use at a higher pressure than the rated pressure, because operating terms may be restricted. For example, if used
as per maximum illustrated operating conditions, intermittent time at maximum flow is restricted to under 1/5 of one cycle time and under 6 seconds
simultaneously. Conditions may vary according to the actual working pressure and delivery (inclination angle of the swash plate). Consult factory
or Yuken sales representative for further information.
Max.
Output Flow
0
20 MPa (2900 PSI)
[27 MPa (3920 PSI)] ∗
1
3. The maximum input power of except "A56R1" pump must be restricted, because of the shaft strength.
Refer to the following page.
No.81
"A" Series Piston Pumps
Variable / Fixed Double PISTON
Allowable Input Power / Instructions PUMPS
Allowable Input Power
With the pumps listed in the table below, there is a limit to the sum of the input power of the inboard and outboard
pumps because of shaft strength.
If both pumps are used for boosting at once, referring to the calculation formulas below, check that the displacements
and discharge pressures of both pumps are within the allowable ranges.
Q1 × P1 + Q2 × P2 <
= LM Q1 × P1 + Q2 × P2 <
= LP
3
Q1 : Displacement (cm /rev) Q1 : Displacement (cu.in/rev)
Outboard Pump Outboard Pump
P1 : Discharge Pressure (MPa) P1 : Discharge Pressure (PSI)
Q2 : Displacement (cm3/rev) Q2 : Displacement (cu.in/rev)
Inboard Pump Inboard Pump
P2 : Discharge Pressure (MPa) P2 : Discharge Pressure (PSI)
LM : See the table below L P : See the table below
Model Numbers LM LP
A16R1/A22R1 523 4627
A37R1 900 7963
A70R1/A70R2 2408 21305
A90R1/A90R2 4348 38470
A145R1/A145R2 4739 41930
No.82
"A" Series Piston Pumps
Variable / Fixed Double PISTON
PUMPS
A
Performance Characteristics / Pipe Flange Kits
Performance Characteristics
Performance characteristics of inboard pump refer to relevant page for performance characteristics of "A" series single
pumps excluding noise level characteristics.
Performance characteristics of outboard pump refer to "PV2R" series vane pump catalogue (catalogue No. Pub. EC-0118).
Performance Characteristics
Model
Inboard Pump Outboard Pump
A16R1 Same as Single Pump "A16", Refer to Page 10
A22R1 Same as Single Pump "A22", Refer to Page 11
A37R1 Same as Single Pump "A37", Refer to Page 12
A56R1 Same as Single Pump "A56", Refer to Page 13 Same as Vane Type Single Pump "PV2R1". Refer to the
Catalogue No. Pub.EC-0118.
A70R1 Same as Single Pump "A70", Refer to Page 14
A90R1 Same as Single Pump "A90", Refer to Page 15
A145R1 Same as Single Pump "A145", Refer to Page 16
A70R2 Same as Single Pump "A70", Refer to Page 14
Same as Vane Type Single Pump "PV2R2". Refer to the
A90R2 Same as Single Pump "A90", Refer to Page 15
Catalogue No. Pub.EC-0118.
A145R2 Same as Single Pump "A145", Refer to Page 16
In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the
flanges. Therefore, please pay cautious attention to the operating pressure when the socket welding flanges are used.
Details of the pipe flange kits are given in the Catalogue No. Pub. EC-3001.
No.83
"A" Series Piston Pumps
A16R1 / A22R1-∗R01∗-∗AAK PISTON
Installation Drawing
PUMPS
X 4.79(.1886)
25 4.76(.1874)
(1.91) (4.29)
(3.78)
109
96
(.98)
(2.44)
(2.28)
62
58
(7.36)
12(.47)
187
(.71)
18
48.5
19.02(.7488) Dia.
82.50(3.248) Dia.
R12
95(3.74) Dia.
19.05(.7500)
(R.47)
82.55(3.250)
21.24(.836)
21.08(.830) 106
Outboard Pump 22.2 12
(.874) (.47) (4.17)
150.5 130
"D" Thd. 17(.67) Deep (5.93) (5.12)
4 Places (Both Sides) 74 74
Discharge Port 19 (.75) Dia. Inboard Pump
Rear Side (2.91) (2.91)
Suction Port 19 (.75) Dia. Surface of Surface of
188
Discharge Port Suction Port
(7.40)
Suction Port Discharge Port
28(1.10) Dia. 15 (.59) Dia.
16 16
(.63) (.63)
(2.063)
(1.500)
38.1
DEC. INC.
"D" Thd. 17(.67) Deep "E" Thd. "F" Deep
4 Places 17.5 4 Places
26.2 (.689)
(1.031) View Arrow X
View Arrow Y
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A16R1-LR01∗-∗AAK-32/3280/3290
A22R1-LR01∗-∗AAK-32/3280/3290
12(.47) Dia. Through
24(.94) Dia. Spotface
4 Places
(3.15)
(.59)
(.55)
15
3(.12)
14
80
50 56.5 95
(1.969) (2.22) (3.74)
95 27.5 72.5 72.5
(3.74) (1.08) (2.854) (2.854)
180
(7.09)
For other dimensions, refer to "Flange Mtg.".
No.84
"A" Series Piston Pumps
A37R1-∗R01∗-∗AAK PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A37R1-FR01∗-∗AAK-32/3280/3290
386.5 62
(15.22) (2.44)
333.5 9.5
(13.13) (.37)
277.5
(10.93)
Y 77
(3.03) 1
202
30 Filling Port (7.95)
(2.311)
[22(.87) Hex. Head Plug Furnished]
58.7
(1.18) 174
Drain Port (6.85)
"C" Thd. 7.97(.3138)
40 7.94(.3126)
X
(4.41)
(4.13)
112
(1.57)
105
(2.28)
58
(7.95)
202
(.55)
(.98)
14
25
(1.91)
48.5
101.55(3.998) Dia.
31.70(1.248) Dia.
R14
101.60(4.000)
120(4.72) Dia. (R.55)
31.75(1.250)
35.32(1.391)
35.16(1.384)
30.2 12 146
Outboard Pump (1.189) (.47) (5.75)
178.5 86 86
"D" Thd. "H" Deep (7.03) (3.39) (3.39)
4 Places (Both Sides) Discharge Port 32 (1.26) Dia. Surface of Surface of
Inboard Pump Discharge Port Suction Port
Rear Side
Suction Port 32 (1.26) Dia.
13 19
Flow Adj. Screw
(2.063)
(1.500)
(.51) (.75)
52.4
38.1
View Arrow Y
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A37R1-LR01∗-∗AAK-32/3280/3290
14(.55) Dia. Through
28(1.10) Dia. Spotface
4 Places
(4.02)
(.59)
(.55)
102
3(.12)
15
14
60 77 120
(2.362)(3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
For other dimensions, refer to "Flange Mtg.".
No.85
"A" Series Piston Pumps
A56R1-∗R01∗-∗AAK PISTON
Installation Drawing
PUMPS
Flange Mtg. : A56R1-FR01∗-∗AAK-32/3280/3290
399 62(2.44)
(15.71)
346 9.5
(13.62) (.37)
290
(11.42) 1
Filling Port
50.5(1.99) [22(.87) Hex. Head Plug Furnished]
2 Surface of Drain Port
Y 43.5(1.71) Drain Port
"C" Thd. (Both Sides)
(2.311)
41 49
58.7
(1.61) (1.93)
40
(1.57) 7.97(.3138)
(2.28)
X 7.94(.3126)
58
(1.91) (5.43)
138
(3.54)
90
(9.29)
236
(.55)
(.98)
25
14
48.5
101.55(3.998) Dia.
31.70(1.248) Dia.
101.60(4.000)
31.75(1.250)
35.32(1.391)
35.14(1.383)
R14
Outboard Pump 30.2 12 146 (R.55)
(1.189) (.47) (5.75)
191 120(4.72) Dia. 174
(7.52) (6.85)
"D" Thd. "H" Deep 100 100
Discharge Port 30 (1.18) Dia.
4 Places (Both Sides) Inboard Pump (3.94) (3.94)
Rear Side
Suction Port 35 (1.38) Dia. Surface of Surface of
Discharge Port 232 Suction Port
Suction Port Discharge Port (9.13)
28(1.10) Dia. 15 (.59) Dia.
(1.500)
(2.063)
38.1
52.4
mm (IN.)
Model Numbers "C" Thd. "D" Thd. "E" Thd. "F" Thd.
H J
A56R1-FR01∗-∗AAK-32 Rc 3/4
M10 M10 M8 19 (.75) 14 (.55)
A56R1-FR01∗-∗AAK- 3/4 BSP.F
3280 3/4 NPT 7/16-14 UNC 3/8-16 UNC 5/16-18 UNC 20 (.79) 16 (.63)
DIMENSIONS IN
MILLIMETRES (INCHES)
Foot Mtg. : A56R1-LR01∗-∗AAK-32/3280/3290
(.59)
3(.12)
102
14
15
60 77 120
(2.362) (3.03) (4.72)
115 42 95 95
(4.53) (1.65) (3.740) (3.740)
230
(9.06)
No.86
"A" Series Piston Pumps
A70R1 / A70R2-∗R01∗-∗AA PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A70R1-FR01∗-∗AA-60/6080/6090
A70R2-FR01∗-∗AA-60/6080/6090 DIMENSIONS IN
MILLIMETRES (INCHES)
62
Fully Extended (2.44)
E
19.5(.77) Surface of Surface of
F Discharge Port 95 95 Suction Port
9.5(.37) (3.74) (3.74)
H
Surface of Surface of
65 2
Drain Port 73 73 Drain Port
Drain Port
(2.063) (2.56) (2.87) (2.87)
52.4
(7.17)
182
4 Places
(.55)
(3.54)
14
90
(4.504)
F
(7.09)
114.4
Y
(.71)
180
18
(4.65)
118
35(1.38) Dia.
31.70(1.248) Dia.
126.95(4.998) Dia.
Inboard Pump Spotface
31.75(1.250)
35.32(1.391)
35.14(1.383)
Discharge Port 16 127.00(5.000) (From Rear)
26.2 (.63) 4 Places 114.4
26 (1.02) Dia.
(1.031) 18 (4.504)
"d" Thd. 17(.67) Deep
4 Places (.71) 134
246.5 (5.28)
(9.70) 181
Outboard Pump (7.126)
211
(8.31)
Eye Bolt
M10
1 Flow Adj. Screw
Filling Port
17(.67) Hex.
(2.752)
DEC.
69.9
View Arrow Z
"f" Thd. "j" Deep
"e" Thd. "h" Deep 4 Places 3
4 Places L Case Drain Port
35.7 "b" Thd. "g" Deep
5 (.20) Hex. Soc. 4 Places
(1.406)
View Arrow X 246.5
(9.70)
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports of inboard pump at your option. Keep the remaining port plugged. Note that on the European design standard
(6080 Design), only the left side, as viewed from the shaft end, of the drain ports is machined.
3. Case drain ports are available for use when draining hydraulic fluid from pump casing.
Dimensions mm (Inches)
Model Numbers
C D E F H J K L N P
439.5 386.5 330.5 58 26.2 52.4 28 17.5 38.1 15
A70R1-FR01∗-∗AA-60∗
(17.30) (15.22) (13.01) (2.28) (1.031) (2.063) (1.10) (.689) (1.500) (.59)
468.5 413.5 333.5 70 30.2 58.7 34 22.2 47.6 21
A70R2-FR01∗-∗AA-60∗
(18.44) (16.28) (13.13) (2.76) (1.189) (2.311) (1.34) (.874) (1.874) (.83)
No.87
"A" Series Piston Pumps
A90R1 / A90R2-∗R01∗-∗AA PISTON
Installation Drawing
PUMPS
Flange Mtg. : A90R1-FR01∗-∗AA-60/6080/6090 DIMENSIONS IN
A90R2-FR01∗-∗AA-60/6080/6090 MILLIMETRES (INCHES)
95
Fully Extended (3.74)
E Surface of Surface of
23(.91) Discharge Port 105 105 Suction Port
F
(4.13) (4.13)
13(.51)
H Surface of Surface of
Drain Port 2 Drain Port Drain Port
119.5 68 68
"a" Thd. (Both Sides)
(2.311)
(4.70) (2.68) (2.68)
58.7
X
63
(2.48)
9.56
(7.50)
190.5
9.53
(4.45)
113
(.3764)
(6.362)
(.3752)
F
161.6
Y
(5.00)
127
38.05(1.498) Dia.
152.35(5.998) Dia.
42.36(1.668)
42.18(1.661)
38.10(1.500)
152.40(6.000)
22
Outboard Pump 30.2 161.6 R22(87)
(.87)
(1.189) 23 (6.362)
"d" Thd. "h" Deep
4 Places (.91) 21.5(.85) Dia. Through
Discharge Port 270 39(1.54) Dia. Spotface
32 (1.26) Dia. (10.63) (From Rear)
Inboard Pump 4 Places
Case Drain Port 3
5 (.20) Hex. Soc. Eye Bolt
1
M10 Flow Adj. Screw
Filling Port 17(.67) Hex. DEC.
(3.063)
77.8
View Arrow Z
"f" Thd. "j" Deep
"e" Thd. "h" Deep 4 Places
4 Places L 42.9
(1.689)
270 "b" Thd. "g" Deep
(10.63) 4 Places
View Arrow X
View Arrow Y
Dimensions mm (Inches)
Model Numbers
C D E F H J K L N P
458 405 349 58 26.2 52.4 28 17.5 38.1 15
A90R1-FR01∗-∗AA-60∗
(18.03) (15.94) (13.74) (2.28) (1.031) (2.063) (1.10) (.689) (1.500) (.59)
497 432 352 70 30.2 58.7 34 22.2 47.6 21
A90R2-FR01∗-∗AA-60∗
(19.57) (17.01) (13.86) (2.76) (1.189) (2.311) (1.34) (.874) (1.874) (.83)
No.88
"A" Series Piston Pumps
A145R1 / A145R2-∗R01∗-∗AA PISTON
PUMPS
A
Installation Drawing
Flange Mtg. : A145R1-FR01∗-∗AA-60/6080/6090
A145R2-FR01∗-∗AA-60/6080/6090 DIMENSIONS IN
MILLIMETRES (INCHES)
112 143
Fully Extended (4.41) (5.63)
E
Surface of Surface of
23(.91) Discharge Port Suction Port
F 112 112
13(.51) (4.41) (4.41)
H 2
Drain Port Surface of Surface of
89 "a" Thd. (Both Sides) Drain Port 72 72 Drain Port
X
(2.311)
70
(2.76)
11.14
(7.81)
198.5
11.11
(4.33)
110
(.4386)
(9.000)
Y
228.6
(.4374)
F
(5.55)
141
152.35(5.998) Dia.
Dia.
152.40(6.000)
Outboard Pump
49.39(1.944)
49.21(1.937)
44.45(1.750)
44.40(1.748)
View Arrow Z
"f" Thd. "n" Deep
"e" Thd. "j" Deep 4 Places "b" Thd. "g" Deep
4 Places L 42.9 4 Places
(1.689) Suction Port
299.5 48(1.89) Dia.
(11.79)
View Arrow X
View Arrow Y
1. Install the pump so that the "Filling Port" is at the top.
2. Use either port of two drain ports of inboard pump at your option. Keep the remaining port plugged. Note that on the European design standard
(6080 Design), only the left side, as viewed from the shaft end, of the drain ports is machined.
3. Case drain ports are available for use when draining hydraulic fluid from pump casing.
Dimensions mm (Inches)
Model Numbers
C D E F H J K L N P
491.5 438.5 382.5 58 26.2 52.4 28 17.5 38.1 15
A145R1-FR01∗-∗AA-60∗
(19.35) (17.26) (15.06) (2.28) (1.031) (2.063) (1.10) (.689) (1.500) (.59)
530.5 465.5 385.5 70 30.2 58.7 34 22.2 47.6 21
A145R2-FR01∗-∗AA-60∗
(20.89) (18.33) (15.18) (2.76) (1.189) (2.311) (1.34) (.874) (1.874) (.83)
No.89
"A" Series Piston Pumps
Variable / Fixed Double Pump PISTON
Spare Parts List
PUMPS
A16R1-∗R01∗-∗AAK-32/3280/3290
A22R1-∗R01∗-∗AAK-32/3280/3290 CAUTION
A37R1-∗R01∗-∗AAK-32/3280/3290 When making replacement of seals bearings or cartridge
A56R1-∗R01∗-∗AAK-32/3280/3290 kits, please do it carefully after reading through the
A70R1/A70R02-∗R01∗-∗AA-60/6080/6090 relevant instructions in the Operator's Manual.
A90R1/A90R02-∗R01∗-∗AA-60/6080/6090
A145R1/A145R02-∗R01∗-∗AA-60/6080/6090
83 82 80 81
Outboard Pump
Inboard Pump
Seals
Seal Kit Numbers Part Numbers
Pump Model Numbers
Complete Kit For Inboard Pump For Outboard Pump (Item 80 O-Ring)
A16R1-∗R01∗-∗AAK-32/3280/3290 KS-A16R1-01-32 KS-A16-01-32
A22R1-∗R01∗-∗AAK-32/3280/3290 KS-A22R1-01-32 KS-A22-01-32
A37R1-∗R01∗-∗AAK-32/3280/3290 KS-A37R1-01-32 KS-A37-01-32
S85(NBR,Hs70)
A56R1-∗R01∗-∗AAK-32/3280/3290 KS-A56R1-01-32 KS-A56-01-32 KS-PV2R1-4010
1Req'd
A70R1-∗R01∗-∗AA-60/6080/6090 KS-A70R1-01-60 KS-A70-01-60
A90R1-∗R01∗-∗AA-60/6080/6090 KS-A90R1-01-60 KS-A90-01-60
A145R1-∗R01∗-∗AA-60/6080/6090 KS-A145R1-01-60 KS-A145-01-60
A70R2-∗R01∗-∗AA-60/6080/6090 KS-A70R2-01-60 KS-A70-01-60
S105(NBR,Hs70)
A90R2-∗R01∗-∗AA-60/6080/6090 KS-A90R2-01-60 KS-A90-01-60 KS-PV2R2-40
1Req'd
A145R2-∗R01∗-∗AA-60/6080/6090 KS-A145R2-01-60 KS-A145-01-60
Notes: 1) When ordering seals, please specify the seal kit number from the table above.
2) Complete seal kit consists of a seal kit for inboard pump, a seal kit for outboard pump and a piece of O-ring for item 80.
3) Seal kit and bearings for inboard pump are same as those for "A" series single pump. For details, please refer to the table below and see the
chart on the page relevant to pump model number concerned.
4) For details of seals and bearing for outboard pump, please see the chart on the following page.
No.90
"A" Series Piston Pumps
Variable / Fixed Double Pumps PISTON
PUMPS
A
Spare Parts List
Detail of Outboard Pump
A∗R1 A∗R2
4 2 7 8 9 5 1 6 4 2 7 8 9 12 5
13 14
12 13
3 15
Cartridge Kits
Model Numbers 4 Cartridge Kit Numbers
A∗R1-∗R01∗-6AAK-32∗/60∗ CPV2R1-6-R-40
A∗R1-∗R01∗-8AAK-32∗/60∗ CPV2R1-8-R-40
A∗R1-∗R01∗-10AAK-32∗/60∗ CPV2R1-10-R-40
A∗R1-∗R01∗-12AAK-32∗/60∗ CPV2R1-12-R-40
A∗R1-∗R01∗-14AAK-32∗/60∗ CPV2R1-14-R-40
A∗R1-∗R01∗-17AAK-32∗/60∗ CPV2R1-17-R-40
A∗R1-∗R01∗-19AAK-32∗/60∗ CPV2R1-19-R-40
A∗R1-∗R01∗-23AAK-32∗/60∗ CPV2R1-23-R-40
A∗R1-∗R01∗-25AAK-32∗/60∗ CPV2R1-25-R-40
A∗R1-∗R01∗-31AAK-32∗/60∗ CPV2R1-31-R-40
A∗R2-∗R01∗-26AA-60∗ CPV2R2-26-R-40
A∗R2-∗R01∗-33AA-60∗ CPV2R2-33-R-40
A∗R2-∗R01∗-41AA-60∗ CPV2R2-41-R-40
A∗R2-∗R01∗-47AA-60∗ CPV2R2-47-R-40
A∗R2-∗R01∗-53AA-60∗ CPV2R2-53-R-40
A∗R2-∗R01∗-59AA-60∗ CPV2R2-59-R-40
A∗R2-∗R01∗-65AA-60∗ CPV2R2-65-R-40
CAUTION
When making replacement of seals, bearings or cartridge
kits, please do it carefully after reading through the
relevant instructions in the Operator's Manual.
No.91
Pub. EC-0106
"AH" SERIES PISTON PUMPS
Variable Displacement-Single Pumps PISTON A
Pressure Compensator Type PUMPS
AH 16 / AH 37 / AH 56
Up to 31 MPa (4500 PSI), 56.2 cm3/rev (3.43 CU.IN./rev)
Drain Port
Journal
Bearing
Flow Adj. Screw
OUT
IN
Shaft
Port Plate
Cylinder Block
Cradle
Spring Slipper Retainer
Piston Ass'y Spring
Features
Port Plate Cradle Support Bearing
A special shape maintains a high volumetric efficiency Compared with conventional bearings, this bearing has
under high pressure and provides greater durability. strengthened rigidity of the swash plate. Noise level has
much lowered because it is supported by a housing.
Volumetric Efficiency
80 Overall Efficiency
70
60
Noise Level
65
HP kW L /min U.S.GPM
40 30 Output Flow 30 8 60 low
Full F
30
Input Power
6
20 20 55
20 4
wer
10 t Po Full Cut-off
10 Inpu 10
2 50
0 5 10 15 20 25 30 MPa
0 0 31
0 0
0 5 10 15 20 25 30
31 MPa
0 1000 2000 3000 4000
4500 PSI
0 1000 2000 3000 4000 Pressure
4500 PSI
Pressure
No.1