This document contains a fluid machinery exam with 9 questions covering topics like negative slip, specific speed, leakage loss, operating characteristics of centrifugal pumps, and efficiency calculations for centrifugal and reciprocating pumps. It provides the question number, description, and point value for each question to be answered within the 45 minute exam period with a total of 35 points possible.
This document contains a fluid machinery exam with 9 questions covering topics like negative slip, specific speed, leakage loss, operating characteristics of centrifugal pumps, and efficiency calculations for centrifugal and reciprocating pumps. It provides the question number, description, and point value for each question to be answered within the 45 minute exam period with a total of 35 points possible.
This document contains a fluid machinery exam with 9 questions covering topics like negative slip, specific speed, leakage loss, operating characteristics of centrifugal pumps, and efficiency calculations for centrifugal and reciprocating pumps. It provides the question number, description, and point value for each question to be answered within the 45 minute exam period with a total of 35 points possible.
Imperial College of Engineering (Affiliated by Rajshahi University)
Department of Mechanical Engineering (Year: 4th; Term: 1st)
Course Name: Fluid Machinery; Course code: ME 3135 CT-01 || Time: 45 min || Full Marks: 35 1. Write short notes on - (3 ×1 = 3) (a) Negative Slip; (b) Specific speed; (c) Leakage loss 2. Why should we choose Centrifugal pump over reciprocating pump? Write 4 reasons. (4 × 0.5 = 2) 3. List the main component parts of Reciprocating pump. (2.5) 4. Write down the working principle of Centrifugal pump with necessary sketch. (2+2 = 4) N √Q 5. Prove that specific speed, N S = (3) H 3/m 4 6. Why do we connect centrifugal pump in series and parallel? write shortly. (1.5) 7. Draw the operating characteristics curve of centrifugal pump. (2.5) 8. A single acting reciprocating pump has a plunger of diameter 250 mm and stroke of 350 mm. If the speed of the pump is 60 r.p.m. and it delivers 18.5 Lit/s. of water against a suction head of 5 m and a delivery head of 20 m, then answer the following questions: (3 ×2.5 = 7.5) (a) Coefficient of discharge (b) The power required to drive the pump (c) Do you think the suction pipe is too long? 9. A centrifugal pump has the following characteristics: (3×2.5 + 1.5 = 9) Outer diameter of impeller = 800 mm; Velocity of whirl of the liquid at the exit from the impeller = 18.39 ms-1 The impeller runs at 550 r.p.m and delivers water at 0.98 m 3s-1 under an effective head of 35 m. A 500 kW motor is used to drive the pump. Assuming that water enters the impeller vanes radially at inlet, Determine – (a) Tangential Velocity at exit; (b) Manometric efficiency; (c) Mechanical efficiency; (d) Overall efficiency
Imperial College of Engineering (Affiliated by Rajshahi University)
Department of Mechanical Engineering (Year: 4th; Term: 1st) Course Name: Fluid Machinery; Course code: ME 3135 CT-01 || Time: 45 min || Full Marks: 35 1. Write short notes on - (3 ×1 = 3) (a) Negative Slip; (b) Specific speed; (c) Leakage loss 2. Why should we choose Centrifugal pump over reciprocating pump? Write 4 reasons. (4 × 0.5 = 2) 3. List the main component parts of Reciprocating pump. (2.5) 4. Write down the working principle of Centrifugal pump with necessary sketch. (2+2 = 4) N √Q 5. Prove that specific speed, N S = (3) H 3/m 4 6. Why do we connect centrifugal pump in series and parallel? write shortly. (1.5) 7. Draw the operating characteristics curve of centrifugal pump. (2.5) 8. A single acting reciprocating pump has a plunger of diameter 250 mm and stroke of 350 mm. If the speed of the pump is 60 r.p.m. and it delivers 18.5 Lit/s. of water against a suction head of 5 m and a delivery head of 20 m, then answer the following questions: (3 ×2.5 = 7.5) (a) Coefficient of discharge (b) The power required to drive the pump (c) Do you think the suction pipe is too long? 9. A centrifugal pump has the following characteristics: (3×2.5 + 1.5 = 9) Outer diameter of impeller = 800 mm; Velocity of whirl of the liquid at the exit from the impeller = 18.39 ms-1 The impeller runs at 550 r.p.m and delivers water at 0.98 m 3s-1 under an effective head of 35 m. A 500 kW motor is used to drive the pump. Assuming that water enters the impeller vanes radially at inlet, Determine – (a) Tangential Velocity at exit; (b) Manometric efficiency; (c) Mechanical efficiency; (d) Overall efficiency