Professional Documents
Culture Documents
Pioneer Deh-P7900ub
Pioneer Deh-P7900ub
CRT3884
DEH-P7900UB/XN/EW5
CD RDS RECEIVER
DEH-P7900UB /XN/EW5
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3195 CRT3815 S10.5COMP2 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
SAFETY INFORMATION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CLASS 1
D
LASER PRODUCT
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
E
A specially instructed person should do servicing operation of the apparatus.
DEH-P7900UB/XN/EW5
2
1 2 3 4
5 6 7 8
CAUTION A
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
Discord used batteries according to the manufacture's instructions.
- Service Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other B
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating. C
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by
electrostatic induction.
DEH-P7900UB/XN/EW5
7
3
5 6 8
1 2 3 4
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
C In addition, be sure that there are no pinched wires, etc.
Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
DEH-P7900UB/XN/EW5
4
1 2 3 4
5 6 7 8
CONTENTS
SAFETY INFORMATION .....................................................................................................................................2
1. SPECIFICATIONS.............................................................................................................................................6
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................8 A
2.1 PACKING....................................................................................................................................................8
2.2 EXTERIOR(1) ...........................................................................................................................................10
2.3 EXTERIOR(2) ...........................................................................................................................................12
2.4 CD MECHANISM MODULE .....................................................................................................................14
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................16
3.1 BLOCK DIAGRAM....................................................................................................................................16
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)..............................................................................18
3.3 KEYBOARD UNIT ....................................................................................................................................24
3.4 CD MECHANISM MODULE(GUIDE PAGE).............................................................................................26
4. PCB CONNECTION DIAGRAM......................................................................................................................34
4.1 TUNER AMP UNIT ...................................................................................................................................34
4.2 KEYBOARD UNIT ....................................................................................................................................38 B
4.3 SWITCH UNIT ..........................................................................................................................................39
4.4 CD CORE UNIT(S10.5COMP2) ...............................................................................................................40
5. ELECTRICAL PARTS LIST.............................................................................................................................42
6. ADJUSTMENT ................................................................................................................................................50
6.1 CD ADJUSTMENT ...................................................................................................................................50
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT ....................................................52
6.3 ERROR MODE .........................................................................................................................................54
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM....................................................................................55
6.5 TEST MODE.............................................................................................................................................56
7. GENERAL INFORMATION .............................................................................................................................57
7.1 DIAGNOSIS..............................................................................................................................................57
7.1.1 DISASSEMBLY......................................................................................................................................57 C
7.1.2 CONNECTOR FUNCTION DESCRIPTION ..........................................................................................61
7.2 IC ..............................................................................................................................................................62
7.3 OPERATIONAL FLOW CHART................................................................................................................77
8. OPERATIONS .................................................................................................................................................78
DEH-P7900UB/XN/EW5
7
5
5 6 8
1 2 3 4
1. SPECIFICATIONS
DEH-P7900UB/XN/EW5
6
1 2 3 4
5 6 7 8
DEH-P7900UB/XN/EW5
7
7
5 6 8
1 2 3 4
19
B
3
20
5 7 1
4 9
C 2
11 10
13
12
15
16
E
22
24
21
14
17
F
23
22
21
DEH-P7900UB/XN/EW5
8
1 2 3 4
5 6 7 8
CRB2319 Russian
DEH-P7900UB/XN/EW5
7
9
5 6 8
1 2 3 4
2.2 EXTERIOR(1)
17
A 34 17
12 17
87 69
16 17
33
19 18
86
13
19
85
30 21 27
22
37 23 25 20
31 1
85 32
38
B
14
26 A
88 11
70 21
A
28
36
35
B
24 29
1
72
1 68
C
5
1
1
A 1 71 4
1
C
6 56
43
60
67 59 58 D
3 55 44 C
43 42
D 63 43 62
67 52
3 E 50 43 47 43
49 43 43 57
39
64 44 51 45 (2) 57
67 46
D D 61
44
48
54
65 53
F 40
F 67
67
E
: GEM1024 G
E 73 3 3
: GEM1069
78 2
(2)
7
77 83
81
76 41
79 2 8
80
75 78
75 10
G
77 10
82 76 9
74 84
82 B 9
F
15
DEH-P7900UB/XN/EW5
10
1 2 3 4
5 6 7 8
41 Cap CKX-003
42 Drive Unit CXC8072
43 Screw BMZ26P040FTC
44 Screw(M2 x 2) CBA1871
45 Cord CDE7392
46 Gear CNV7752
47 Gear CNV7753 F
48 Gear CNV7754
49 Gear CNV7755
DEH-P7900UB/XN/EW5
7
11
5 6 8
1 2 3 4
2.3 EXTERIOR(2)
2 2
A
1
4
21 2
5
B
2
13 11
14
6
16
B 15
10
12 9
18
8
7
17
19
DEH-P7900UB/XN/EW5
12
1 2 3 4
5 6 7 8
6 Connector(CN1801) CKS5662
7 Holder CND3781
8 Double Sided Tape CNM8673
9 Holder CNV9435
10 OEL Unit MXS8231
11 Holder CNV9676 B
12 Button Unit(SRC/BAND) CXC7257
13 Button Unit(LIST) CXC7264
14 Knob Unit CXC7271
15 Spring XBL7005
21 IC(IC1931) GP1UX31RK
DEH-P7900UB/XN/EW5
7
13
5 6 8
1 2 3 4
DEH-P7900UB/XN/EW5
14
1 2 3 4
5 6 7 8
31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201
36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211
41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV7218
45 Gear CNV7219
46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV7799
49 Arm CNV7805
DEH-P7900UB/XN/EW5
7
15
5 6 8
1 2 3 4
CE2
LDET
CE1
DO
SL
DI
CK
12
XD0-15
/RESET
7 6 13 5 10 9 8 11 14 18 19 20 21
FLASH ROM XA0-19 XA0-21
FM/AM TUNER UNIT
NC
CE2
ROM_VDD
SL
DI
CK
CE1
LDET
DO
RDS_CK
RDS_DATA
RDS_LOCK
RDS_HSLK
IC541
PEH084A CO
T
OE 49
/OE 28 nOE
/CE 26 FLCS 53
nCS
/WE
11 WE 48 nW
IC3 EEPROM IC5 16
← XD0-15
5.0V 5V 3.3V /WE
SDRAM XA0-16,20,21
IC551
OSC LPF
HY57V641620
B CN402
AM ANT
ETP-H
FMRF
1
ANTENNA 1 ATT 38 SDCLK 44
CLK SD
2,3 37 SDCKE 46 SD_
CKE
IC1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER
RF adj
ANT adj
5
IC401
NJM062M
T51 CF52 7
8 79 USB
80
IC291 9,10 US
11
AUDIOGND
IC4 TC4066BFT
OSCGND
VDD_3.3
←
RFGND
VCC
Q291
NC
C
2 12 15 22 16 4 17
LINE AMP
CN271 IC271 TUN3V
3 NJM4558MD SYS8V
2 3
AUX 1
1 AUXL
2
Vref IC912
CN151 3.3V REGULATOR NJM2130F3
84
USDN 1 3 3,4 1 TUAUSEL
2 IC171 US3V Vref SYS8V
USDP NJM2885DL1-33 EMUTE 57
3
USB IC161 SACLK 58
LT1766EFE-5 SAOUT
90
4 2 4
1 US5V 5
VOUT VIN SW SHDN 15 USBPW AMPPW 3
12 14 22
FB SYNC SYNC 85
10 MUTE
BIAS
IC151 6
BOOST 1
R5523N001B SYSPW
45
EN 1 USBCTL
3 87 13
FLG FLG XIN
X601
11 15.000MHz
D CN101 XOUT
7 BUSL+
11 BUSL- 40
FLPILM
5 BUS- 5 1 28
IP BUS TX
C CD CORE UNIT(S10.5COMP2) 1
8
BUS+ 6 IP-BUS DRIVER
IC101
HA12241FP
2 27
19
RX
RX2 KEYD
2
89
KEYAD
PICK-UP UNIT RF-AMP, CD DECODER, 8
MP3/WMA DECODER, Q101 79 NC 32
IPPW
(P10.5)(SERVICE) D
DIGITAL SERVO / BUP NC 31
DATA PROCESSOR 7
VDD CNVSS
LASER CN101
DIODE LD- 80
15 15 141 CN701 ASENBO 24 BZ
Q101 LD CN701 PEE BUZ
MD 142 LOUT
5 5 PD 55 LOUT CDL SYSTEM
REFO LOUT 13 3
VREF 8 133 CONTROLLER
8 REFOUT 50
XTAL
AC,BD,F,E IC601(2/2)
HOLOGRAM X201 PEG300A
UNIT 16.93MHz
52 BUP
FOM /XTAL
FOM
3 3 CD VDD
FOP FOP CD 3.3V REGULATOR
MONITOR
FOCUS ACT. 2 2 DRIVER IC201 Q102
TOP
DIODE TRACKING ACT. 1 1 TOP PE5547A VDD 3 IC781 1
TOM TOM IC301 VCC 9 7 VDD 41
4 4 NJM2885DL1-33 ILMPW
E LD+
14 14
BA5839FP TD,FD 39
12 /PUEN
FOM
11 SD,MD 36
FOP ROT0
14 16 /RESET RESET 92
TOP /RESET 8 8 CDRST 35 SWVDD
13 ROT1
TOM Q841
BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK
SPINDLE
MOTOR M BDATA,BSCK VDD
16
MECHA VD
SOP LOEJ
22 5 Q751
15 LOEJ VD VD
SOM VD 1 15 BUP 38
18 21 43 SWVDD
LOAD/ CARRIAGE LCOP CLCONT CLCONT Q752
MOTOR M 17
LCOM CONT
9 41
2 14
CONT
VD AUTO FLAP
MOTOR DRIVE RESET
10
18
11 IC871 VDCONT
VDSENS CN871 BA6288FS
8
12EJ FLM02 11 Q651
7 4 14 52
8EJ OUT2 RIN FLPCLS
6 M FLM01 3 6
DSCSNS 53
9 5 OUT1 FIN FLPOPN
HOME AUTO FLAP 4 VM 91
DSENS
S904 S905 S901 5 29
VCC DPDT
12EJ 8EJ HOME FLOP 50
2 FOPNSW 30
KYDT
3 FLCL 51
FCLSSW
S903 Q871
1
DSCSNS BUP BUP
Q872 Q85
F
D 49
FLPPW 20
SWITCH OELPW
UNIT
DEH-P7900UB/XN/EW5
16
1 2 3 4
5 6 7 8
CN302
RL RL
Q302
CE2 69
XD0-15 1.8V REGULATOR TUNPCE2
CN301 RCA OUT
7,24,40, CE1 70
VDDI, 58,73, 5 IC181 1,3 TUNPCE1 SWL SWL
XA0-19 XA0-21 US3V DO 47
VDDP 74,91, NJM2872BF18 TUNPDO
USB 110,124 DI 46 Q303
CONTROLLER TUNPDI
CK 48
IC501 TUNPCK
TCC8600-00X SL 95 SL
28 OE 49 55 FL FL
Q401
nOE -EA-AG XIN
26 FLCS 53 X502
nCS3/nOE3 RDS_LOCK 65 Q321 Q301
12MHz RDSLK
XOUT 54
BUP
WE 48 nWE RDS_HSLK 64
RDS57K
XD0-15 nRESET 77 CN992(1/2)
Q402
XA0-16,20,21
iPod CP RDS_DATA 66 RDT VDD 1
IC581 DALMON
341S2025 SYSTEM 5
93 15 RDS_CK
GPIO_D16 I2C_SDA 16
RCK CONTROLLER
VDD 5V REGULATOR
B
GPIO_D17
94 7 I2C_SCL IC601(1/2) Q901
38 SDCLK 44 LDET 17 PEG300A
SD_CLK 122 11 LDET
EXINT2 CP_READY VDD
37 SDCKE 46 SD_CKE 42
nRESET 38 XRST Q902
19 SDCS 47 SD_nCS
←
95 2 3V 5V 4 34
GPIO_D18 IC583 USB_RX 67
DALMON
TC7SET08FUS1 BUP CN991
96 33 USBTX
GPIO_D19 BACKUP SENSE
123 43 WUP 73 BUP2 1
EXINT3 BSENS
D/A CONVERTER Q921
72 ACC1
IC561 ASENS 5
AK4388VT 5V REGULATOR
14 5 1,3 ACC SENSE
BCLK
86 2 VDD IC562 SYS8V Q931
BICK
8 NJM2872BF05 81 ILL1
LRCK 87 4 LRCK DIFO ISENS 3
MCLK 88 1 MCLK Q951
3 SDTI LPF
79 USBHO_DN DAO 89 8 ILM SENSE TEL1
111 6 SMUTE AOUTL 11 3 IC563 1,2 TELIN 8
SCK1 93 ASLIN
80 112 NJM4558MD
9,10 USBHO_DP 5 RSTN
SFRM1
T TELEPHONE MUTE
Vref GND1
2
VR251 ELECTRONIC VOLUME/
MIC251
SOURCE SELECTOR BUP
20
C
NoiseDetOut POWER AMP 6,20
USBL 10 OutPreL 40 VCC1,2
IN1L
22 38 12 5 FL1 12
MicIn OutFL IN2(FL) OUT2+
AUTUL 8 39 14 3 FL2 10
IN3L IC201 OutRL IN4(RL) OUT2-
PML016B IC351 21 RL1 11
OUT4+
BUSL+ 7 PAL007C 23 RL2 9
IN4L+ 4 OUT4-
6
SAOut
BUSL- STBY
SAClk
IN4L- 25 BRE1
Mute
CDL 9 Switch_out 4
VP
MUTE 57 Q381 RR RR
- +
SACLK58 SYS+B REGULATOR
BUP
BACK FR FR
90 2 UP - +
AOUT SYS8V IC911 1
BUP FL FL
MPPW 3
B.
Q352 NJM2388F84 ILL REM - +
85 4 RL RL
MUTE GND ACC
- +
1 SYSPW CN992(2/2)
YSPW
Q241 RWBUSY
VDD 2
13 OELB RWCLK
XIN 3
X601 TUNER3V Q242 RWCNVSS
9
11 15.000MHz REGULATOR DPDT
XOUT 10 D
3 IC431 1 KYDT 4
TUN3V SYS8V
NJM2885DL1-33 RESET
8
40
LPILM Q831
2 CN661 3
KEYD WIRED
89 2
KEYAD 1 REMOTE
NC 32
NC 31
7
CNVSS
24 BZ601
PEE BUZZER
R
ILM+B
Q821
BUP
Q822 B KEYBOARD UNIT
CN801 CN1801
41 ROTARY COMMANDER
LMPW IL+B IL+B
13 12 S1811 E
36 ROT0 ROT0 Phase_B 10 JOYST
ROT0 8 7
35 SWVDD ROT1 ROT1 Phase_A 1
ROT1 9 8 ROM Q1963 Q1964
Q841
SWVDD SWVDD IC1921
VDD 10 9 SWVDD 33
BYTE PD8173A
3V REGULATOR
38 4,5 IC1951 2 23
WVDD
A19
A18
Vcc
CE
OE
JOYST
VCC2
AVCC
DIMMER
CS1
Vref
CS0
CS2
RD
REM
RST1 RESET S1801
AVCC1,2
5 4 RESET 13
CVCC
DSENS XIN
91 DSENS KEY/OEL CONTROLLER
VDD
SENS 2 1 X1901
DPDT 27 IC1901 CN1961
29 DPDT 11 16MHz
DPDT 6 5 DPDT PEG312A8 XOUT 5,6 8 14
30 KYDT KYDT 28
KYDT 7 6 KYDT
Q851 LS,CKD,OELD,DSEL
OEL+B OEL+B
BUP 15 14
Q852
SWVDD F
IC851 18V
6,7 1 OELB
NJM2360M Q1961
20 Q1962
ELPW 12V REGULATOR
DC-DC CONVERTER 12V
DEH-P7900UB/XN/EW5
7
17
5 6 8
1 2 3 4
A-a A-b
Large size
SCH diagram
A-a
+2.2dBm
C
R530 470
100
R01
C
C
CN701
+0.6dBm
R556 2R2K
R555
2R2K
22P
+2.2dBm
-20dBm
E
FM/AM TUNER UNIT
CN1801
B
M3
S2 CSN1052
S1 CSN1051
XXA7400
OPEN
ANTENNA
CLOSE
F
D SWITCH UNIT
A D
DEH-P7900UB/XN/EW5
18
1 2 3 4
5 6 7 8
A-b A
CD 0dB: +14dBm
+3.29dBm
FRONT
R CH
FRONT
L CH
SUBWOOFER
C533 R001 R CH
SUBWOOFER
L CH B
CD 0dB:
+14dBm REAR
L CH
REAR
R CH
R530 470
100
> >
CD 0dB: +10dBm
RDT
RDT
22P RDSLK
RDSLK
RDS57K
RDS57K
E
CD 0dB: +36dBm
RR RR
- +
BACK FR FR
UP - +
ILL B. FL FL
REM - +
CN1801
GND ACC RL RL
- +
B
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor. 2.2 ←2R2
No differentiation is made between chip capacitors and 0.022 ←R022
discrete capacitors.
A
DEH-P7900UB/XN/EW5
7
19
5 6 8
F
E
B
A
D
C
20
A-a A-b
A-b
1
1
1
+1.89dBm A TUNER AMP UNIT
CD 0dB: +14dBm
+3.29dBm
FRONT
R CH
FRONT
L CH
SUBWOOFER
2
2
C533 R001 R CH
SUBWOOFER
L CH
CD 0dB:
+14dBm REAR
L CH
REAR
R CH
530 470
DEH-P7900UB/XN/EW5
3
3
> >
4
4
CD 0dB: +10dBm
CD 0dB: +10dBm
RDT
RDT
RDSLK
RDSLK
RDS57K
5
5
RDS57K
6
6
CD 0dB: +36dBm
RR RR
- +
DEH-P7900UB/XN/EW5
BACK FR FR
UP - +
B. FL FL
ILL REM
7
7
- +
GND ACC RL RL
- +
4
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
discrete resistors. are expressed as :
Symbol indicates a capacitor. 2.2 ←2R2
No differentiation is made between chip capacitors and 0.022 ←R022
8
8
discrete capacitors.
A-b
21
E
A
D
C
F
B
F
E
B
A
D
C
22
A-a A-b
A-a
A-b
1
1
+2.2dBm
2
2
C533
R530 470
100
DEH-P7900UB/XN/EW5
3
3
R01
C
CN701
2
+0.6dBm
4
4
R556 2R2K
R555
R556 2R2K
R555
2R2K
22P
5
5
+2.2dBm
3
6
6
-20dBm
DEH-P7900UB/XN/EW5
7
7
CN1801
4
M3
XXA7400
ANTENNA
OPEN
CLOSE
8
8
S2 CSN1052
S1 CSN1051
D SWITCH UNIT
A-a A-b
A-a D
A-b
23
E
A
D
C
F
B
1 2 3 4
RESET
A
CN801
TA DISPLAY
EJECT SW EQ
B
DEH-P7900UB/XN/EW5
24
1 2 3 4
5 6 7 8
B KEYBOARD UNIT A
PEG312A8
B
DEH-P7900UB/XN/EW5
7
25
5 6 8
1 2 3 4
A
C-a
PICKUP UNIT(P10.5)(SERVICE)
F
%
T
F
T
F
F
T F F
F F
T T T
T T
C #
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
M1 CXC7134
SPINDLE MOTOR
S
C
$
C
M2 CXC4026
LOADING/CARRIAGE MOTOR T S
9 7
F C
0 8 4
5
E
F
F
3 T
T
2
S
C
S
C
CD DRIVER
C
DEH-P7900UB/XN/EW5
26
1 2 3 4
5 6 7 8
A
C-b
C CD CORE UNIT(S10.5COMP2)
!
B
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
A
CN701
^ &
C
DEH-P7900UB/XN/EW5
7
27
5 6 8
F
E
B
A
D
C
28
C-a C-b
C-b
1
1
C CD CORE UNIT(S10.5COMP2)
2
2
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
DEH-P7900UB/XN/EW5
3
3
4
4
5 6 7 8
CN701
A
A
6
B
&
^
C
C-a C-b
D
2 3 C-b
DEH-P7900UB/XN/EW5
7
29
5 6 8
F
E
B
A
D
C
30
C-a C-b
C-a
C-b
1
1
PICKUP UNIT(P10.5)(SERVICE)
2
2
F
%
DEH-P7900UB/XN/EW5
T
F
3
3
T
F
F
T F F
F F
T T T
T T
4
4
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH ON-OFF
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5
5
M1 CXC7134
SPINDLE MOTOR
2
C
$
C
M2 CXC4026
T
6
6
LOADING/CARRIAGE MOTOR S
9 7
F C
0 8 4
F
F
3 T
T
DEH-P7900UB/XN/EW5
C
C
S
S
7
7
CD DRIVER
3
8
8
C-a c-b
C-a
C-b
31
E
A
D
C
F
B
1 2 3 4
- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div
28SNS 5 V/div 5CLCONT 5 V/div 28SNS 5 V/div
312SNS 5 V/div 4LOEJ 5 V/div 312SNS 5 V/div
4LOEJ 5 V/div 6VD 10 V/div 4LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation
7SIN 1 V/div 1 s/div 0FIN 200 mV/div 500 ms/div @TE 500 mV/div 200 ms/div
8CIN 500 mV/div !RFOK(MONI_2) 2 V/div #FE 500 mV/div
9TIN 1 V/div 7SIN 2 V/div
12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation
#FE 500 mV/div 20 ms/div $MDX 2 V/div 200 ms/div $MDX 2 V/div 5 µs/div
0FIN 500 mV/div 7SIN 500 mV/div 7SIN 500 mV/div
@TE 500 mV/div
9TIN 500 mV/div
D CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)
0FIN 500 mV/div 200 ms/div @TE 500 mV/div 2 ms/div %RFAGC 1 V/div 500 µs/div
E #FE 500 mV/div %RFAGC 500 mV/div @TE 500 mV/div
9TIN 500 mV/div
DEH-P7900UB/XN/EW5
32
1 2 3 4
5 6 7 8
%RFAGC 1 V/div 500 µs/div %RFAGC 1 V/div 500 µs/div %RFAGC 1 V/div 2 ms/div
A
@TE 500 mV/div @TE 500 mV/div @TE 500 mV/div
9TIN 500 mV/div 9TIN 500 mV/div 9TIN 500 mV/div
%RFAGC 1 V/div 200 ms/div ^LOUT 1 V/div 200 µs/div 1DSCSNS 5 V/div 500 ms/div
@TE 1 V/div &ROUT 1 V/div 28SNS 5 V/div
8CIN 1 V/div 312SNS 5 V/div
7SIN 2 V/div 4LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div %RFAGC 1 V/div 500 µs/div
5CLCONT 5 V/div 28SNS 5 V/div 9TIN 1 V/div
4LOEJ 5 V/div 312SNS 5 V/div @TE 1 V/div
4LOEJ 5 V/div 0FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 µm) during play
DEH-P7900UB/XN/EW5
7
33
5 6 8
1 2 3 4
SIDE B
P.C.Board Chip Part
120
110
US
C 100
90
80
70
D
60
50
40
E
30
20
10
F Y
0
10 20 30 40 50 60 70
X
A
DEH-P7900UB/XN/EW5
34
1 2 3 4
5 6 7 8
SIDE A
ANTENNA
Y
AUX IN RCA OUT
1
2 B
C CN701
D E
M3
2 18
1 17
B CN1801
TEST1
PCL1
SIDE B
150
140
B
130
120
110
100 C
90
80
70
D
60
50
40
30
20
10
Y F
0
100 90 80 70 60 50 40 30 20 10
X
A
DEH-P7900UB/XN/EW5
7
37
5 6 8
1 2 3 4
A
B KEYBOARD UNIT SIDE A
B KEYBOARD UNIT SIDE B
RESET
160
160
EJECT
150
150
140
140
B
130
130
TA
120
120 CN801
OEL
UNIT
DISPLAY
110
110
C
100
100
SW
90
90
80
80
EQ
70
70
D
60
60
50
50
40
40
E
30
30
LIST
20
20
SOURCE
BAND
10
10
X
X
F
0
0
30
40
10
30
20
40
10
B
20
Y
Y
DEH-P7900UB/XN/EW5
38
1 2 3 4
5 6 7 8
D SWITCH UNIT
A CN871
20
B
10
OPEN
CLOSE
Y
C
0
30 20 10
X
D
DEH-P7900UB/XN/EW5
7
39
5 6 8
1 2 3 4
E
M2
LOADING
/CARRIAGE
MOTOR
M1
SPINDLE
MOTOR
C
DEH-P7900UB/XN/EW5
40
1 2 3 4
5 6 7 8
C
DEH-P7900UB/XN/EW5
7
41
5 6 8
1 2 3 4
D A
Unit Number : CWN2151
Q
Q
352
381
(A,134,35) Transistor
(B,32,102) Transistor
UMD2N
2SC4081
Q 401 (A,147,110) Transistor UMH1N
Unit Name : Tuner Amp Unit Q 402 (A,151,110) Transistor UMH1N
Q 501 (B,61,75) Transistor DTC114EUA
MISCELLANEOUS
Q 651 (A,134,31) Transistor 2SC4081
IC 101 (A,12,115) IC HA12241FP Q 751 (A,12,56) Transistor 2SD2396
IC 151 (A,66,94) IC R5523N001B Q 752 (A,18,60) Transistor UMD2N
IC 161 (A,44,96) IC LT1766EFE-5 Q 821 (A,91,15) Transistor 2SD1767
IC 171 (A,90,100) IC NJM2885DL1-33 Q 822 (A,98,15) Transistor UMD2N
IC 181 (A,87,94) IC NJM2872BF18
Q 831 (A,86,12) Transistor DTC114EUA
IC 201 (A,121,84) IC PML016B Q 841 (A,136,22) Transistor UMF23N
E
IC 271 (A,116,124) IC NJM4558MD Q 851 (A,21,43) Transistor 2SD1760F5
IC 291 (A,141,88) IC TC4066BFT Q 852 (A,21,34) Transistor UMD2N
IC 351 (A,90,135) IC PAL007C Q 871 (A,61,13) Transistor 2SD1760F5
IC 401 (A,155,94) IC NJM062M
Q 872 (A,49,6) Transistor UMD2N
IC 431 (B,156,84) IC NJM2885DL1-33 Q 901 (A,12,69) Transistor 2SD2396
IC 501 (A,68,72) USB Media Control IC TCC8600-00X-EA-AG Q 902 (A,12,77) Transistor UMD2N
IC 541 (A,76,41) IC PEH084A Q 921 (A,67,108) Transistor UMX1N
IC 551 (A,60,41) SD-RAM(64M) HY57V641620ETP-H Q 931 (A,78,117) Transistor DTC114EUA
IC 561 (A,52,77) IC AK4388VT
Q 951 (B,99,109) Transistor 2SA1576A
IC 562 (A,42,83) IC NJM2872BF05 D 151 (B,74,98) Diode MALS068X
F IC 563 (A,42,73) IC NJM4558MD D 152 (B,74,96) Diode MALS068X
IC 581 (A,94,76) IC 341S2025 D 161 (A,50,96) Diode 1SS355
IC 583 (A,98,57) L-MOS AND GateTC7SET08FUS1 D 162 (A,50,102) Diode RB160L-40
IC 601 (A,129,54) IC PEG300A
D 163 (A,46,107) Diode 1SR154-400
DEH-P7900UB/XN/EW5
42
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
D 241 (A,142,28) Diode HZS12L(B1) L 871 (A,142,17) Ferri-Inductor LAU4R7K
D 251 (A,138,70) Diode Network DA204U L 951 (A,84,119) Inductor CTF1617
D 261 (B,112,73) Diode Network DA204U X 502 (A,83,77) Crystal 12.000 MHz CSS1723
D 271 (B,120,134) Diode MALS068X X 581 (A,94,86) Crystal 32.768 kHz CSS1735 A
D 272 (B,112,134) Diode MALS068X X 601 (A,115,54) Crystal Resonator 15.000 MHz CSS1653
D 321 (A,111,116) Diode 1SS133 VR251 (A,126,116) Semi-fixed 10 kΩ(B) CCP1229
D 381 (B,27,100) Diode HZU8R2(B2) >FU301 (A,122,127) Fuse 3 A CEK1286
D 382 (B,112,111) Diode DAN202U >FU302 (A,109,99) Fuse 3 A CEK1286
D 431 (A,154,85) Diode 1SR154-400 MIC251 (A,135,115) Microphone CPM1068
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 306 (B,109,104) RS1/16S390J R 529 (A,82,70) RS1/16S101J
R 307 (B,103,110) RS1/16S223J R 530 (A,84,70) RS1/16S471J
R 308 (B,103,105) RS1/16S223J R 531 (A,84,66) RS1/16S101J
A R 532 (A,82,67) RS1/16S101J
R 309 (A,140,125) RS1/16S390J
R 310 (A,150,127) RS1/16S390J R 533 (A,80,66) RS1/16S101J
R 311 (B,142,136) RS1/16S223J R 535 (A,78,75) RS1/16S102J
R 312 (B,144,136) RS1/16S223J R 536 (A,57,55) RAB4CQ101J
R 321 (A,120,109) RS1/16S102J R 537 (A,81,63) RAB4CQ101J
R 538 (A,57,73) RS1/16S101J
R 351 (A,90,118) RS1/16S182J
R 352 (A,88,118) RS1/16S182J R 539 (A,78,79) RS1/16S225J
R 353 (A,93,118) RS1/16S182J R 541 (B,79,54) RS1/16S0R0J
R 354 (A,95,118) RS1/16S182J R 542 (A,62,83) RS1/16S101J
R 355 (B,89,113) RS1/16S272J R 543 (A,63,83) RS1/16S101J
R 544 (B,59,68) RS1/16S101J
B R 356 (B,87,113) RS1/16S272J
R 357 (B,93,113) RS1/16S272J R 550 (A,56,69) RS1/16S472J
R 358 (B,97,113) RS1/16S272J R 551 (B,60,83) RS1/16S223J
R 359 (B,147,121) RS1/16S472J R 552 (B,57,71) RS1/16S223J
R 360 (B,142,116) RS1/16S472J R 553 (B,57,74) RS1/16S223J
R 554 (B,61,71) RS1/16S473J
R 362 (A,111,108) RS1/16S103J R 555 (A,52,46) RS1/16S222J
R 363 (B,103,118) RS1/16S103J R 556 (A,52,43) RS1/16S222J
R 364 (B,102,118) RS1/16S331J
R 365 (B,99,124) RS1/16S101J R 561 (A,50,62) RS1/16S473J
R 366 (A,100,122) RS1/16S103J R 562 (A,49,62) RS1/16S473J
R 563 (A,43,66) RS1/16S103J
R 381 (B,28,103) RS1/16S473J R 564 (B,42,72) RS1/16S103J
C R 382 (A,135,80) RS1/16S473J R 565 (A,41,67) RS1/16S103J
R 383 (B,32,100) RS1/16S104J
R 384 (A,111,110) RS1/16S473J R 566 (B,44,76) RS1/16S103J
R 403 (B,156,91) RS1/16S104J R 567 (A,57,74) RS1/16S101J
R 568 (B,42,68) RS1/16S822J
R 404 (B,154,96) RS1/16S104J R 569 (B,48,64) RS1/16S822J
R 405 (B,166,114) RS1/16S681J R 582 (B,97,82) RS1/16S103J
R 406 (B,167,119) RS1/16S681J
R 407 (B,165,119) RS1/16S681J R 583 (A,88,76) RS1/16S103J
R 408 (B,165,128) RS1/16S681J R 584 (A,88,73) RS1/16S1003F
R 585 (A,80,86) RS1/16S332J
R 409 (B,163,128) RS1/16S681J R 586 (B,54,60) RS1/16S332J
R 410 (B,161,129) RS1/16S681J R 587 (A,83,86) RS1/16S182J
D R 417 (A,143,111) RAB4C223J
R 501 (B,63,81) RS1/16S471J R 588 (B,52,60) RS1/16S182J
R 502 (A,73,84) RS1/16S0R0J R 590 (A,100,59) RS1/16S101J
R 591 (A,92,82) RS1/16S104J
R 504 (B,54,64) RS1/16S101J R 592 (A,91,82) RS1/16S104J
R 505 (A,56,64) RAB4CQ101J R 593 (A,89,82) RS1/16S104J
R 507 (A,56,84) RS1/16S101J
R 508 (A,57,84) RS1/16S101J R 594 (B,97,57) RS1/16S332J
R 510 (A,55,59) RAB4CQ101J R 595 (B,98,58) RS1/16S182J
R 596 (A,88,79) RS1/16S104J
R 511 (A,60,55) RS1/16S101J R 597 (A,97,82) RS1/16S0R0J
R 512 (B,57,76) RS1/16S471J R 600 (A,96,85) RS1/16S0R0J
R 513 (B,59,78) RS1/16S471J
E
R 514 (A,61,56) RS1/16S101J R 601 (B,112,59) RS1/16S104J
R 515 (B,63,79) RS1/16S471J R 602 (B,118,58) RS1/16S0R0J
R 603 (B,136,63) RS1/16S104J
R 516 (A,66,85) RS1/16S390J R 604 (B,127,50) RS1/16S104J
R 517 (A,66,58) RAB4CQ101J R 605 (B,96,62) RS1/16S472J
R 518 (A,67,88) RS1/16S390J
R 519 (A,68,56) RAB4CQ101J R 606 (B,118,41) RS1/16S472J
R 520 (B,68,85) RS1/16S104J R 607 (B,130,62) RS1/16S104J
R 610 (B,105,65) RS1/16S102J
R 522 (A,71,58) RAB4CQ101J R 612 (B,138,48) RS1/16S681J
R 523 (A,74,55) RS1/16S101J R 613 (A,141,41) RS1/16S104J
R 524 (A,77,59) RAB4CQ101J
F
R 525 (A,80,59) RAB4CQ101J R 615 (B,121,59) RS1/16S104J
R 526 (A,78,82) RS1/16S472J R 616 (A,139,41) RS1/16S104J
R 617 (B,118,43) RS1/16S222J
R 527 (A,85,70) RS1/16S101J R 618 (B,100,62) RS1/16S104J
R 528 (A,81,70) RS1/16S473J R 619 (B,98,62) RS1/16S104J
DEH-P7900UB/XN/EW5
44
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 253 (A,125,113) CKSRYB474K10 C 517 (A,74,82) CKSYB475K10
C 254 (A,121,68) CEALNP100M16 C 518 (B,71,80) CKSRYB122K50
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 753 (B,23,57) CKSRYB473K25 D 1837 (A,20,23) LED CL-197HB1-D(CDE)
C 781 (A,37,64) CEJQ220M25
C 782 (B,40,76) CKSRYB103K50 D 1838 (A,83,5) LED CL-197HB1-D(CDE)
D 1839 (A,114,5) LED CL-197HB1-D(CDE) A
C 783 (B,38,76) CKSRYB474K10 D 1840 (A,151,5) LED CL-197HB1-D(CDE)
C 821 (A,96,15) CKSRYB473K25 D 1841 (A,129,5) LED CL-197HB1-D(CDE)
C 831 (A,89,11) CKSRYF104Z50 D 1842 (A,67,23) LED CL-197HB1-D(CDE)
C 841 (A,130,21) CKSRYB473K25
C 842 (A,132,21) CCSRCH101J50 D 1901 (B,82,20) Diode 1SS355
L 1951 (B,117,14) Inductor CTF1617
C 851 (A,132,17) 4.7 µF CCG1111 L 1961 (B,145,22) Inductor CTF1617
C 852 (A,36,37) CEJQ470M25 TH1961 (B,117,19) Thermistor CCX1037
C 854 (B,36,32) CKSRYB103K50 X 1901 (B,85,19) Ceramic Resonator 16.000 MHz CSS1616
C 855 (A,30,28) CCSRCH331J50
C 856 (B,37,44) CKSRYB104K16 S 1801 (A,162,7) Push Switch CSG1155
S 1811 (A,49,23) Switch CSX1120
C 857 (A,34,44) CEJQ101M16 S 1831 (A,10,40) Push Switch CSG1155 B
C 858 (A,28,43) CEJQ470M16 S 1832 (A,10,7) Push Switch CSG1155
C 859 (A,19,33) CKSRYB104K16 S 1834 (A,25,23) Push Switch CSG1155
C 860 (A,27,35) 22 µF CCG1183
C 871 (B,150,28) CCSRCH101J50 S 1835 (A,110,6) Push Switch CSG1155
S 1836 (A,125,6) Push Switch CSG1155
C 872 (B,149,31) CKSRYB102K50 S 1837 (A,95,6) Push Switch CSG1155
C 873 (B,150,21) CCSRCH101J50 S 1838 (A,79,6) Push Switch CSG1155
C 874 (A,71,7) CEAL101M10 S 1839 (A,155,6) Push Switch CSG1155
C 875 (A,66,5) CKSRYB104K16
C 876 (B,144,19) CKSRYB105K10 RESISTORS
C 877 (A,62,5) CKSRYB103K50 R 1801 (B,101,37) RS1/16S222J
C 878 (A,154,18) CKSRYB103K50 C
R 1802 (B,101,39) RS1/16S222J
C 901 (A,21,66) CEHAR220M16 R 1803 (B,159,16) RS1/16S333J
C 902 (A,17,65) CKSRYB104K16 R 1811 (B,53,28) RS1/16S103J
C 903 (B,16,72) CKSRYB103K50 R 1812 (B,47,21) RS1/16S333J
B
Unit Number:
R
R
R
1837
1838
1841
(B,20,33)
(B,30,35)
(B,10,31)
RS1/16S0R0J
RS1/16S821J
RS1/16S821J
Unit Name : Keyboard Unit
R 1843 (B,31,32) RS1/16S821J
R 1901 (B,83,34) RS1/16S103J
MISCELLANEOUS R 1902 (B,79,25) RS1/16S473J E
R 1903 (B,80,20) RS1/16S154J
IC 1901 (B,97,23) IC PEG312A8 R 1904 (B,84,29) RAB4CQ102J
IC 1921 (A,144,23) IC PD8173A
IC 1931 (A,72,32) IC GP1UX31RK R 1905 (B,74,8) RS1/16S104J
IC 1951 (B,112,13) IC S-818A33AUC-BGN R 1906 (B,93,35) RAB4CQ473J
Q 1961 (B,131,15) Transistor 2SC4617 R 1907 (B,70,19) RAB4CQ102J
R 1908 (B,52,10) RS1/16S221J
Q 1962 (A,127,18) Transistor 2SD1664 R 1909 (B,97,35) RAB4CQ473J
Q 1963 (B,58,14) Transistor DTC123JU
Q 1964 (B,27,28) Transistor DTC123JU R 1910 (B,96,11) RAB4CQ101J
D 1831 (A,32,23) LED CL-197HB1-D(CDE) R 1911 (B,101,12) RAB4CQ101J
D 1832 (A,49,5) LED CL-197HB1-D(CDE) R 1912 (B,105,12) RAB4CQ101J
R 1913 (B,140,28) RS1/16S101J F
D 1833 (A,49,41) LED CL-197HB1-D(CDE) R 1914 (B,100,35) RS1/16S101J
D 1834 (A,99,5) LED CL-197HB1-D(CDE)
D 1835 (A,11,37) LED CL-197HB1-D(CDE) R 1915 (B,149,28) RAB4CQ101J
D 1836 (A,11,10) LED CL-197HB1-D(CDE)
DEH-P7900UB/XN/EW5
7
47
5 6 8
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 1916 (A,99,15) RAB4CQ101J
R 1917 (A,102,17) RAB4CQ101J RESISTORS
R 1918 (A,105,18) RAB4CQ101J
A R 1919 (B,144,25) RAB4CQ101J R 101 (B,60,73) RS1/10SR2R4J
R 102 (B,59,71) RS1/10SR2R4J
R 1920 (B,104,34) RAB4CQ101J R 103 (B,60,71) RS1/10SR2R7J
R 1931 (B,67,25) RS1/16S101J R 104 (B,52,69) RS1/16SS222J
R 1932 (B,69,27) RS1/16S103J R 105 (B,41,57) RS1/16SS102J
R 1933 (B,70,21) RS1/16S2R2J
R 1951 (B,127,10) RS1/16S222J R 107 (B,41,59) RS1/16SS105J
R 202 (B,32,62) RS1/16SS473J
R 1961 (B,121,19) RS1/16S333J R 203 (B,42,45) RS1/16S473J
R 1962 (B,131,13) RS1/16S183J R 204 (A,25,61) RS1/16SS221J
R 1963 (B,119,19) RS1/16S563J
R 1964 (B,121,17) RS1/16S392J R 206 (B,26,53) RS1/16SS104J
R 1965 (A,102,30) RAB4CQ101J R 210 (B,13,32) RS1/16SS102J
B
R 214 (B,36,34) RS1/16SS472J
R 1966 (A,129,22) RS1/16S0R0J R 216 (B,47,49) RS1/16SS472J
R 1967 (B,130,10) RS1/16S5101D R 221 (B,36,32) RS1/16SS103J
E
C
Unit Number : CWX3514
C
C
106
202
(B,56,69)
(A,27,57)
CKSQYB475K6R3
CKSSYB104K10
Unit Name : CD Core C 204 (A,24,63) CKSSYB103K16
C 205 (B,23,43) CKSQYB475K6R3
Unit(S10.5COMP2)
C 206 (A,22,39) CKSSYB104K10
MISCELLANEOUS C 207 (A,24,37) CKSRYB104K16
C 209 (B,33,40) CEVW220M6R3
C 210 (B,29,42) CKSSYB104K10
IC 201 (A,34,46) IC PE5547A
C 211 (A,27,34) CKSSYB104K10
IC 301 (A,27,14) IC BA5839FP
Q 101 (B,56,72) Transistor 2SA1577
C 212 (B,29,32) CKSRYB104K16
Q 102 (B,47,57) Transistor 2SB1689
C 213 (A,44,37) CKSSYB104K10
C 214 (A,28,33) CKSSYB104K10
X 201 (A,23,35) Ceramic Resonator 16.934 MHz CSS1603
F C 216 (A,50,51) CKSSYB332K50
S 901 (A,53,37) Switch(HOME) CSN1067
C 217 (A,46,51) CKSSYB104K10
S 903 (B,19,58) Switch(DSCSNS) CSN1067
S 904 (B,38,67) Switch(12EJ) CSN1068
C 218 (A,49,51) CKSSYB473K10
S 905 (B,24,68) Switch(8EJ) CSN1068
DEH-P7900UB/XN/EW5
48
1 2 3 4
5 6 7 8
D
Unit Number : CWS1389 C
DEH-P7900UB/XN/EW5
7
49
5 6 8
1 2 3 4
6. ADJUSTMENT
6.1 CD ADJUSTMENT
A
DEH-P7900UB/XN/EW5
50
1 2 3 4
5 6 7 8
- Flow Chart
[Key] [EQ] + [DISP] + Reset or
[EQ] + [DISP] + BU + ACC
Contents Test Mode In
Display A
*6 C
[BAND] [2]
Power Off Tracking Open
*) After the [EJECT] key is pressed keys other than the [EJECT] key should not be pressed, until disc ejection is complete.
When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for F
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
DEH-P7900UB/XN/EW5
7
51
5 6 8
1 2 3 4
Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
B
Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE
CD CORE UNIT(S10.5COMP2)
C REFO1
E F L.P.F.
Xch Ych
E 100 kΩ
Oscilloscope
VREF 390 pF
F 100 kΩ
VREF 390 pF
D L.P.F.
Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the [→] and [←] buttons, move the PU unit to the innermost track.
3. Press key [3] to close focus, the display should read "91". Press key [2] to implement the tracking balance
adjustment the display should now read "81". Press key [3]. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75°. Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
DEH-P7900UB/XN/EW5
52
1 2 3 4
5 6 7 8
0° 30°
45° 60°
75° 90°
DEH-P7900UB/XN/EW5
7
53
5 6 8
1 2 3 4
DEH-P7900UB/XN/EW5
54
1 2 3 4
5 6 7 8
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TEST1 IC601(Pin 86) terminal to H.
The clock signal is output from the PCL1 terminal IC601(Pin 37).
The frequency of the clock signal is 468.750 kHz that is one 32th of the fundamental frequency.
The clock signal should be 468.750 kHz ± 19 Hz.
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.
DEH-P7900UB/XN/EW5
7
55
5 6 8
1 2 3 4
Normal connection
Enter the TEST1 command Enter the TEST2 command Enter the TEST3 command Enter the TEST4 command
Reset start
- Indications
Indication of system microcomputer Ver V e r * . * *
E
Indication of TCC firmware Ver V e r * . * *
MIN SEC SEC
TCC firmware VerUp is getting ready. R E A D Y 0 0 0 Displays 0:00 to 3:00 (in increments of minutes and seconds)
TCC firmware VerUp is started. U P D T 0 0 0 Displays 0:00 to 3:00 (in increments of minutes and seconds)
TCC firmware VerUp is completed. COMP L E T E * The time increment stops when it reaches 3:00.
DEH-P7900UB/XN/EW5
56
1 2 3 4
5 6 7 8
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A
1 1
Fig.1
1 1
E
Grille Assy
Fig.2
DEH-P7900UB/XN/EW5
7
57
5 6 8
1 2 3 4
4
2 Remove the screw. 1
3 3
DEH-P7900UB/XN/EW5
58
1 2 3 4
5 6 7 8
B
B
A
Damper
Damper D
A
Carriage Mechanism Lower Frame
DEH-P7900UB/XN/EW5
7
59
5 6 8
1 2 3 4
Screw
B
CD Core Unit
Solder
Planet Gear
Pickup Rack
Chassis
Pickup
DEH-P7900UB/XN/EW5
60
1 2 3 4
ANTENNA REAR OUTPUT
5
5
6
6
IP-BUS INPUT
FRONT
OUTPUT WIRED REMOTE INPUT USB
SUBWOOFER AUX
OUTPUT
7.1.2 CONNECTOR FUNCTION DESCRIPTION
DEH-P7900UB/XN/EW5
1. BUS+
7
7
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15 2. GND
3. GND
4. NC
5. BUS- 8 9 10 11
1 B.UP 9 RL- 6. GND 5 6 7
2 GND 10 FL- 7. BUS L+ 1 2 3 4
3 ILL 11 RL+ 8. ASENB
4 B.REM 12 FL+ 9. BUS R+
5 ACC 13 RR-
10. BUS R-
6 NC 14 FR-
11. BUS L-
7 NC 15 RR+
8 MUTE 16 FR+
8
8
61
E
A
D
C
F
B
F
E
B
A
D
C
62
7.2 IC
PAL007C
PEH084A
1
1
R5523N001B
LT1766EFE-5
A15 1 48 A16
A14 2 47 byte
PEH084A
A13 3 46 VSS
A12 4 45 DQ15/A-1
A11 5 A0 to A19 : 20 addresses inputs 44 DQ7
R5523N001B
1
5
A9 7 42 DQ6
2
2
EN
mode), A-1(LSB address input,
VOUT
UVLO
TCC8600-00X-EA-AG
ce : Chip enable
THERMAL
NC 10 39 DQ12
SHUTDOWN
oe : Output enable
we 11 we : Write enable 38 DQ4
GATE
2
RY/by : Ready/Busy output
NC 13 36 DQ11
GND
VCC : 3.0 volt-only single power supply
NC 14 NC : Pin not connected internally 35 DQ3
DEH-P7900UB/XN/EW5
PEG300A
341S2025
RY/by 15 34 DQ10
A18 16 33 DQ2
LIMIT
FLAG
NJM2872BF05
NJM2872BF18
DELAY
3
3
CURRENT
A17 17 32 DQ9
A7 18 31 DQ1
3
4
VIN
FLG
A6 19 30 DQ8
A5 20 29 DQ0
A4 21 28 oe
A3 22 27 VSS
A2 23 26 ce
PE5547A
PD8173A
PEG312A8
A1 24 25 A0
4
4
HY57V641620ETP-H
GND 8
NC 7
BOOST 6
NC 5
VIN 4
NC 3
SW 2
GND 1
BOOST
5
LT1766EFE-5
5
6
- Pin Layout
VIN 4
17
- Block Diagram
RLIMIT RSENSE
GND
2.9 V BIAS INTERNAL + -
BIAS 10 REGULATOR VCC
CURRENT
11 VC
13 NC
COMPARATOR
SLOPE COMP
9 GND
16 GND
10 BIAS
Σ
15 shdn
14 SYNC
SYNC 14
ANTISLOPE COMP
12 FB/SENSE
SHUTDOWN
COMPARATOR
6
6
200 kHz
+ - OSCILLATOR S Q1
RS DRIVER
POWER
FLIP-FLOP CIRCUITRY
SWITCH
R
0.4 V
5.5 A 2 SW
shdn 15 +
FREQUENCY
- FOLDBACK
LOCKOUT
DEH-P7900UB/XN/EW5
COMPARATOR
7
7
×1
Q2
VC(MAX) FOLDBACK
CLAMP Q3 CURRENT
LIMIT ERROR
CLAMP AMPLIFIER -
gm = 2000 Mho 12 FB
+
1.22 V 1, 8, 9,
2.38 V
16, 17
GND
11
8
8
VC
63
E
A
D
C
F
B
1 2 3 4
PAL007C
sw_vcc
A
Protector;
Over voltage
1
TAB Reference
amp_vcc
Stand-by
2
P-GND2 Circuit
+-
3
OUT2-
Offset Protector;
4
-+
5
OUT2+
6
VCC
+-
B
7
OUT1-
Offset
8
P-GND1 Detection
-+
9
OUT1+
10
SVR
11
IN1
12 13
IN2
amp_vcc
Protector;
S-GND Short circuit
14
IN4
C
15
IN3
16
AC-GND
17
+-
OUT3+
18
Offset
P-GND3 Detection
19
-+
OUT3-
20 21
VCC
+-
OUT4+
22
Offset
D MUTE Detection
23
-+
OUT4-
24 25
P-GND4
SWITCH
sw_vcc
stby
Protector;
Over current limit
Mute circuit
TC4066BFT
E
IN/OUT1 1 14 VDD
OUT/IN1 2 13 CONT1
OUT/IN2 3 12 CONT4
IN/OUT2 4 11 IN/OUT4
CONT2 5 10 OUT/IN4
CONT3 6 9 OUT/IN3
F
VSS 7 8 IN/OUT3
DEH-P7900UB/XN/EW5
64
1 2 3 4
5 6 7 8
- Pin Functions(TCC8600-00X-EA-AG)
Pin No. Pin Name I/O Function and Operation
1 VSS Digital ground
2-6 XD[4]-[8] I/O External bus data bit [4]-[8]. Internal pull-up resistor enabled at reset. A
7 VDDI Digital power for internal core (1.8 V)
8 VSS Digital ground
9 VDDIO Digital power for I/O (3.3 V)
10-16 XD[9]-[15] I/O External bus data bit [9]-[15]. Internal pull-up resistor enabled at reset.
17-23 XA[0]-[6] I/O External bus address bit [0]-[6]
24 VDDI Digital power for internal core (1.8 V)
25 VSS Digital ground
26 VDDIO Digital power for I/O (3.3 V)
27-39 XA[7]-[19] I/O External bus address bit [7]-[19]
40 VDDI Digital power for internal core (1.8 V)
41,42 XA[20], [21] I/O External bus address bit [20], [21]
B
43 VDDIO Digital power for I/O (3.3 V)
44 SD_CLK I/O SDRAM clock
45 VSS Digital ground
46 SD_CKE I/O SDRAM clock enable signal. Active high.
47 SD_nCS I/O Chip select signal for SDRAM, active low
48 nWE I/O Static memory write enable signal. Active low.
49 nOE I/O Static memory output enable signal. Active low.
50 nCS[0]/ND_nOE[0] I/O External bus chip select [0] / NAND flash output enable [0]
51 nCS[1]/ND_nOE[1] I/O External bus chip select [1] / NAND flash output enable [1]
52 nCS[2]/ND_nOE[2] I/O External bus chip select [2] / NAND flash output enable [2]
53 nCS[3]/ND_nOE[3] I/O External bus chip select [3] / NAND flash output enable [3]
54 XOUT O 12 MHz crystal oscillator output C
55 XIN I 12 MHz crystal oscillator input. Voltage must not exceed VDDI (1.95 V).
56 XTOUT O 32.768 kHz crystal oscillator output
57 XTIN I 32.768 kHz crystal oscillator input. Voltage must not exceed VDDI (1.95 V).
58 VDDI Digital power for internal core (1.8 V)
59 VSS Digital ground
60 GPIO_B[6] I/O GPIO_B[6]
61 ND_nWE I/O NAND flash WE. Active low
62 UART0TXD I/O UART0 TX data
63 UART0RXD I/O UART0 RX data
64 READY I Ready information from external device.
65 VDDIO Digital power for I/O (3.3 V)
66 ADIN4 General purpose multi-channel ADC input 4 D
67 ADIN2 General purpose multi-channel ADC input 2
68 ADIN0 General purpose multi-channel ADC input 0
69 VDDADC Analog power for ADC (3.3 V)
70 VSSADC Analog ground for ADC
71 VSSPLL1 Analog ground for PLL
72 XFILT1 PLL1 filter output. 1 200 pF capacitor is required.
73 VDDPLL1 Analog & digital power for PLL1 (1.8 V)
74 VDDPLL Analog & digital power for PLL (1.8 V)
75 XFILT PLL0 filter output. 350 pF capacitor is required.
76 VSSPLL Analog ground for PLL
77 nRESET I System Reset. Active low.
78 MODE1 I Mode setting input 1. Pull-down for normal operation. E
DEH-P7900UB/XN/EW5
7
65
5 6 8
1 2 3 4
D TCC8600-00X-EA-AG
96
65
PML016B
97 64 - Pin Layout
44
43
42
41
40
39
38
37
36
35
34
1 33
2 32
128 33
3 31
1
32
E 4 30
5 29
6 28
7 27
8 26
9 25
10 24
11 23
F
12
13
14
15
16
17
18
19
20
21
22
DEH-P7900UB/XN/EW5
66
1 2 3 4
B
F
C
D
A
67
8
8
IN4+_R
IN4+_L
IN4-_R
IN4-_L
IN1_R
IN2_R
IN3_R
IN3_L
IN2_L
IN1_L
7
Primary Volume
DEH-P7900UB/XN/EW5
HPF
MIC_in
HPF
MIC Anti-Alias Filter
DC_filter Amp
LPF LPF BASS TRE
TRE BASS
Noise_DET_out
Phase inv.
6
6
CLK
Digital
DATA Anti-Rad. Filter Anti-Rad. Filter Anti-Rad. Filter Anti-Rad. Filter Anti-Rad. Filter Anti-Rad. Filter
STB
Block
MUTE
Secondary Secondary Secondary Secondary Secondary Secondary
Volume Volume Volume Volume Volume Volume
Vcc Supply
Vref &
GND Reference
- Block Diagram
5
Vp
Pref
PGND
Tout_FL
Front_L
Tout_RL
Rear_L
Tout_PreL
Tout_PreR
Rear_R
Front_R
Tout_FR
SVin_FL
SVin_RL
PRE/SW_L
SVin_PreL
SVin_PreR
PRE/SW_R
SVin_RR
Tout_RR
SVin_FR
5
1 2 3 4
AK4388VT
- Block Diagram
A MCLK
VDD
DEM VSS
De-emphasis Clock
SMUTE
Control Control Divider VCOM
ACKS
DIF0 Port
DIF1 DZF
8X ΔΣ SCF
B AOUTL
LRCK Audio Interpolator Modulator LPF
BICK Data
SDTI Interface 8X ΔΣ SCF
AOUTR
Interpolator Modulator LPF
RSTN
- Pin Layout
C
MCLK 1 16 DZF 341S2025
BICK 2 15 DEM
40
31
SDTI 3 14 VDD 1 30
LRCK 4 13 VSS
RSTN 5 12 VCOM
SMUTE 6 11 AOUTL
ACKS 7 10 AOUTR
DIF0 8 9 DIF1 10 21
11
20
D
- Pin Functions (341S2025)
Pin No. Pin Name I/O Function and Operation
1 VCC Supply voltage, positive terminal
2 XIN 32.768 kHz crystal oscillator or external clock source
3 XOUT 32.768 kHz crystal oscillator or external clock source
4 CLOCK_ENAB I CLOCK_OUT enable (active high)
5,6 NC Not used
7 I2C_SCL I/O I2C clock
8-10 I2C_ADDR0-2 I I2C slave address selection
11 CP_READY O CP ready to receive next instruction (active high)
12 MODE0 I Operating voltage selection
E 13 MODE1 I Communication mode selection
14 NC Not used
15 I2C_SDA I/O I2C data
16 MODE2 I Communication mode selection
17 ROSC I Connect via 100 k 1% resistor to VCC
18 SPI_nSS I SPI slave select (active low)
19 SPI_SIMO I SPI master-to-slave data
20 SPI_SOMI O SPI slave-to-master data
21 SPI_UCLK I SPI clock
22-31 NC Not used
32 CLOCK_OUT O 32.768 kHz clock output, if selected by CLOCK_ENAB
33-37 NC Not used
F
38 nRESET I CP reset (active low)
39 VSS Supply voltage, negative terminal
40 VCC Supply voltage, positive terminal
DEH-P7900UB/XN/EW5
68
1 2 3 4
5 6 7 8
DEH-P7900UB/XN/EW5
7
69
5 6 8
1 2 3 4
PEG300A
100
76
1 75 Format Meaning
C CMOS
N Nch open drain
25 51
26
50
DEH-P7900UB/XN/EW5
70
1 2 3 4
144
109
1 108
VIN
GND
CONTROL
PE5547A
5
5
NJM2872BF05
NJM2872BF18
VDD 1 54 VSS
- Block Diagram
DQ0 2 53 DQ15
VDDQ 3 52 VSSQ
36 73
DQ1 4 51 DQ14
DQ2 5 CLK : Clock Input 50 DQ13
37
72
VSSQ 6 CKE : Clock Enable Input 49 VDDQ
HY57V641620ETP-H
Bandgap
Reference
6
Column Address Strobe,
6
DQ6 11 44 DQ9
Protection
NOISE
BYPASS
cas 17 38 CLK
DEH-P7900UB/XN/EW5
ras 18 37 CKE
7
7
cs 19 36 NC
1
5
BA0 20 35 A11
BA1 21 34 A9
2
N
C
A10/AP 22 33 A8
Format
4
A0 23 32 A7
- Pin Layout
A1 24 31 A6
A2 25 30 A5
A3 26 29 A4
CMOS
1. VIN
Meaning
VDD 27 28 VSS
2. GND
5. VOUT
8
8
Nch open drain
3. CONTROL
4. NOISE BYPASS
71
E
A
D
C
F
B
1 2 3 4
DEH-P7900UB/XN/EW5
72
1 2 3 4
5 6 7 8
DEH-P7900UB/XN/EW5
7
73
5 6 8
1 2 3 4
DEH-P7900UB/XN/EW5
74
1 2 3 4
5 6 7 8
PEG312A8
Format Meaning
100
76
C CMOS
1 75 N Nch open drain
D
PD8173A
31 D15/A-1
33 BYTE
25 51
23 VCC
32 VSS
29 D14
27 D13
25 D12
43 A19
40 A10
39 A11
38 A12
37 A13
36 A14
35 A15
34 A16
44 NC
30 D7
28 D6
26 D5
24 D4
42 A8
41 A9
26
50
E
VCC : Power supply voltage
A5 6 A0 to A19 : Address input
D0 to D14 : Data output
A0 11 NC : Non connection
BYTE : Mode switch
A3 8 OE : Output enable
CE : Chip enable
A1 10 VSS : GND
F
CE 12
VSS 13
OE 14
D0 15
D8 16
D1 17
D9 18
D2 19
D10 20
D3 21
D11 22
1
2
3
4
5
A4 7
A2 9
NC
A18
A17
A7
A6
DEH-P7900UB/XN/EW5
7
75
5 6 8
1 2 3 4
RDS_CK
RDS_LOCK
CE2
CE1
RDS_HSLK
CK
LDET
SL
DI
DO
ROM_VDD
NC
RDS_DATA
A
IC 3 EEPROM IC 5
5.0V 5V t 3.3V
OSC LPF
AM ANT FMRF
1 AT T
Rch
24
IC 2
2.5V
FM ANT IC 1
3 3.3V
AT T Lch
23
FMRF MIXER, IF AM P DET, FM MPX,
B RDS DECODER
RF adj
ANT adj
T51 CF52
AUDIOGND
IC 4
OSCGND
VDD_3.3
RFGND
VCC
NC
2 12 15 22 16 4 17
DEH-P7900UB/XN/EW5
76
1 2 3 4
5 6 7 8
A
Power ON
VCC=5 V
Pin 14
bsens
Pin 73
B
bsens=L
asens
Pin 72
asens=L
DSENS
- 2 V < DSENS < 4.5 V
Pin 91
C
2 V < DSENS < 4.5 V
ASENBOtH *1 *1 DALMON, USBPW and USBCTL
Pin 80 operates at the same time.
Starts
communication
with Grille
microcomputer. 500 ms
SWVDDtH
Pin 38 300 ms D
Source ON
DEH-P7900UB/XN/EW5
7
77
5 6 8
1 2 3 4
8. OPERATIONS
DEH-P7900UB/XN/EW5
78
1 2 3 4
5 6 7 8
DEH-P7900UB/XN/EW5
7
79
5 6 8
1 2 3 4
DEH-P7900UB/XN/EW5
80
1 2 3 4
5 6 7 8
DEH-P7900UB/XN/EW5
7
81
5 6 8
1 2 3 4
- Jigs List
Name Jig No. Remarks
A Test Disc TCD-782 Checking the grating
L.P.F. Checking the grating (Two pieces)
- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module, EXTERIOR
B
Grease GEM1045 CD Mechanism Module
Grease GEM1069 EXTERIOR
DEH-P7900UB/XN/EW5
82
1 2 3 4