Professional Documents
Culture Documents
Mechanical Technical Questions and Answers PDF 1677665618
Mechanical Technical Questions and Answers PDF 1677665618
17) Quill is
A) A tool used in milling machine to cut T-slots B) A holding device used on planers C) Cutting a blind
key way on an object D) A steel tube in the head of some machine tools that encloses the bearings
and rotating spindle on which are mounted the cutting tools E) None of these
18) Which of the following materials will have highest value of contraction allowance?
A) Cast iron B) Aluminium C) Brass D) Malleable iron E) None of these
25) A diffuser
A) Converts kinetic energy into thermal energy B) Converts potential energy into kinetic energy C)
Converts pressure energy into kinetic energy
D) Converts thermal energy into kinetic energy E) None of these
29) Surging is
A) An unsteady, periodic and reversal of flow in the compressor. B) The fixed mass flow rate
regardless of pressure ratio C) The reduction in lift force at higher angles of incidence D) None of these
E) All the above
31) In case of black body A) =0, =0, =1 B) =0, =1, =1 C) =0, =1, =0 D) =1, =1, =0 E)
=1, =0, =0
42. Which of the following methods in welding uses a pool of molten metal?
a. Carbon arc welding b. TIG welding c. Submerged arc welding d. MIG welding
e. Thermit welding
43. Moment of inertia of a triangular section of base (b) and height (h) about an axis passing through its
vertex and parallel to the base is __________ than that passing through its C.G. and parallel to the base.
a. Nine times b. six times c. four times d. one-half e. one-third
45. A taper provided on the pattern for its easy and clean withdrawal from the mould is known as A.
machining allowance B. draft allowance c. shrinkage allowance d. distortion allowance e. None of the
above
49. The branch of science that deals with study of body in motion, considering the forces that causes the
motion is known as
a. Dynamics b. Statics c. Kinematics d. Kinetics e. None of these
51. Which mechanical property a metal should possess to enable it to be mechanically formed?
a. ductility b. malleability c. elasticity e. machinability e. None of the above
A) B)
a. First angle and third angle b. Third angle and first angle c. Third angle and fourth angle
d. Fourth angle and third angle e. None of the above
57. Which one of the following processes in welding uses non-consumable electrodes?
a. TIG welding b. MIG welding c. Manual arc welding d. Submerged arc welding
e. None of the above
58. The properties of LASER are high coherence, unidirectional, Monochromatic, Long distance
propagation
62. Necking? a. drill a hole in a plate b. groove is a cylinder c. initially making a spot to join the metal
d. drill with rivet
74. Sulphur is removed from cast-iron when same is melt in cupola the flux is --?
78. Velocity distribution for laminar flow in circular pipe? Ans: Parabolic
81. Carbon steel is an alloy of iron and carbon with varying quantities of ………..?
Phosphorous & sulphur
82. Varigon’s theorem - Algebraic sum of moments of a given set of forces about a point is equal to the
moment of their resultant.
85. Pantograph, all pairs are a. sliding b. turning c. spherical d. self closed pair
89. If mass/energy transfer is zero, then what system? Ans: Isolated system
91. What chuck is used for brass castings? a. 4 jaw b. 3 jaw c. collet d. magnetic
93. Purpose of tolerance a. for perfect fit b. can’t machine exact size c. allowance.
102. Flash point of fuel is Minimum temperature to which oil is heated in order to give off
inflammable vapours in sufficient quantity to ignite momentarily when brought in contact with a
flame
106. Fuel-air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as
compared to clean filter will be? Higher
107. In S.I engines, air fuel ratio for idling speed is?
115. If operating temperature of system is low, then refrigerant with low boiling point should be used
121. A ball is throwing up. The sum of kinetic and potential energies will be maximum at
a. Ground b. Highest point c. In the centre while going up d. At all the points
e. In the centre while coming down
132. A fly wheel starts from rest and accelerates uniformly and reaches 25 rpm in 3 seconds. What will
be the angular velocity (in rpm) after 10 seconds? a. 20 b. 25 c. 45 d. 50
144. The correct relation between Gauge pressures, Absolute pressure, Atmospheric pressure (4 choices)
149. The oil of sp. gravity 0.9 and water are kept in two identical vessels, Hydro static Pressure at
bottom of oil will be a. More than pressure of the water at the bottom b. Less than pressure of the water
at the top c. Same d. Insufficient data
152. The sate of the refrigerant in the vapour compression cycle before throttling
a. Wet b. Dry
154. High moisture content in the last stage of turbine will cause
a. Corrosion b. Low thermal efficiency c. Low Blade life d. All the above
155. What alloying material imparts corrosive resistance properties of steel a. Ni-Cr b. V,Cr c. Cr
160. What will happen to the specific volume of the water when it is heated from 0 degree c
a. Increases b. Decreases c. Remain Constant
168. What is the material of Crank Shaft? Forged Steel or Less Carbon Steel
170. Energy stored in the spring when it is fully compressed without any deformation is Strain Energy
175. For same compression ratio which of the following cycle is more efficient?
a. Otto b. diesel c. Dual Cycle d. All the above.
176. The angle between face of the tool and plane parallel to the base of the tool is
a. rake angle b. clearance angle c. cutting edge angle d. lip angle
183. Convert volumetric to gravitational, relative volume of each constituent of flue gas
a. %mw b. xmv c. me d. xsw e. %sw
187. Under ideal condition, isothermal, isochoric, adiabatic and isobaric are
a. Static b. dynamic c. quasi-static d. stable e. thermodynamic
189. If Q1 is the heat in source, Q2 is the cold sink for heat pump then COP
a. Q1 / (Q1- Q2) b. Q2 / (Q1- Q2) c. (Q1- Q2) / Q1 d. Q2 / Q1
191. Key used between shaft and pulley is made from? Cold rolled mild steel bars
192. Hardness of steel depends on shape & distribution of ….in iron? Carbides
202. For same power, same speed, flywheel of petrol and diesel engine are
a. smaller b. greater c. equal d. none
206. When the Centre of pressure and Centre of gravity are equal?
When the body is horizontal
207. Flow of particles in definite path without change in the path of the particle
a. One dimensional b. laminar c. turbulent d. steady state
210. Axial flow pump is used large flow and small head of fluid
214. Reverse joule cycle is ………. (Bell coalman cycle, Rankine cycle, brayton cycle)
215. During idling and low speed running which mixture is used……..rich mixture, lean mixture,
216. Multi slurry is used for …………? High efficiency, balancing and uniform torque, run
continuously when one cylinder is failed.
218. In which process max work can be obtained….? Const Volume, Const Pr, Const Temp, Const
Entropy
223. A belt drive, where pulley dia is double, and then it key length must be
a. doubled b. same c. increase the critical length d.
226. D1 and D2 are pulley dia, and then the speed ratio is given by D2/D1
229. What is recrystallation temperature? Maximum temperature upto which old crystal disappears
230. What is austempering? Heated steel is quenched from the Austenizing Temperature
237. The surface to be machined are marked on the pattern by the following color
a) Black b) yellow c) red d) blue e) green
240. The difference between planner and shaper is that in former case
a) Tool moves over stationary work b) tool moves over reciprocating work
c) Tool can machine internal as well as external details d) both tool and job reciprocates
e) Tool is stationary and job reciprocates
244. The operation of milling two sides of a work piece simultaneously is called
a) Gang milling b) climb milling c) square milling d) straddle milling e) End milling
245. In which type of milling operation the chip is cut off at thinnest place and the chip thickness
increases along chip length a) Up milling b) down milling c) end milling d) climb milling e) key way
milling
257. Pressure applied in a liquid in all directions will be given by Pascal’s law.
262. What is the use of index pulley? To provide grip to the pulley.
265. Property of which type of material is same in all directions? Isotropic of materials
267. In a cantilever beam when a point load is applied on free end, where will failure occur? At the
fixed end.
268. Plastic deformation due to constant load at high temp is known as Creep.
282. Cutting speed of HSS tools while cutting low carbon steel is:
A. 40M/Min B. 250M/Min C. 500M/min D. none of the above
283. Cutting speed of carbide tools while cutting low carbon steel is:
A. 40M/Min B. 250M/Min C. 500M/min D. 80M/Min
285. The circularity achieved by finish turning on a standard centre lathe is:
a. 0.005-0.008mm b. 0.0-0.08mm c. 0.1-0.2mm d. 0.2-0.3mm
290. The displacement accuracy which can be achieved on a jig boring machine is:
A. 5/µm B. 50/µm C. 100/µm
296. In a right angle transmission by helical gears, the hands of the helix of the gears are:
A. same B. opposite C. immaterial D. none of the above
299. Ball bearings are not generally used in crank shafts of automobiles because:
A. of high cost B. of high speed C. cannot be assembled D. none of the above
307. Ratio between velocity of sound and velocity of any object is:
A. prandtl number b. Reynolds number c. Avagadro’s number d. Mach number
310. Four beams of identical sections and lengths are made of cast iron, aluminium, steel and hardened
steel. The beams are fixed at both ends, for a uniformly distributed load which will deflect least: a. Cast
iron b. Aluminium c. Steel d. Hardened steel
313. Effect of increase of outside diameter of a helical compression spring on its rigidity is:
a. Increased rigidity b. Decreased rigidity c. No effect d. Dry friction
326. For a laminar flow Reynolds flow should be Less than 2000
329. A pipe friction test shows that, over the range of speeds used for the test, the non-dimensional
friction factor f, varies inversely with Reynolds No. It can be inferred from above that, ans. Pipe should
be smooth.
330. In a rough turbulent flow in a pipe, the friction factor would depend upon?
Ans. Pipe diameter and pipe condition.
342. The temp that is numerically the same in Fahrenheit & centigrade scales is ________?
344. Dew point is the temperature at which water vapor will undergo ________?
Ans. Condensation
348. Identify the odd one out a. DIN b. ISI c. JIS d. IIT
349. If the NPSH requirements of a pump are not satisfied it wills _______?
351. A parallel flow heat exchanger will perform better than a counter flow heat exchanger. State
whether this is true or false
352. The index that normally reflects laminar flow in a tube is ______? Ans. Reynolds no.
353. Pressure drop in air duct is influenced by __________? ans. Shape of the duct
354. By increasing the intake air temp, efficiency of IC engine will _______? Ans. decrease
356. Theoretical correct air fuel ratio for petrol a.6:1 b.9:1 c. 10:1 d. 15:1
358. Ignion quality of the diesel fuel oil is measure by index no is called
a. octane b. cetene c. calorific value d. carbon no
363. Hoop stress induced in the thin cylinder by winding it with wire under tension will be
a.0 b.tensile c.compressive d.shear
365. ------------ gear train is one in which each shaft call as one wheel only
a.simple b.compound c.epicyclic d.none
367. If the earth shrinks by half the radius duration of one day
A.4 hrs b.6 hrs c.12 hrs d.24 hrs
371. What will be the locus of a point on a thread unwound from a cylinder?
a. involute b. helix c. straight line d. circle
378. A stone initially at rest is dropped from the edge of a very tall building. Taking acceleration as
10m/s2, what was the change in the speed of the stone during the 4th second?
a. 10m/s b. 30m/s c. 15m/s d. 40m/s e. None of the above
380. In latent heating, a substance involves _________ in phase with _________ in temperature.
A. change, increase B. no change, increase C. change, no increase D. no change, no increase
E. none of the above
381. For a cantilever beam with uniformly varying load, shape of bending moment curve is
a) Parabolic b) hyperbolic c) Straight line d) cubic e) None of the above
384. The mercury does not wet with the glass. This is due to the property of the liquid known as
a. Cohesion b. Adhesion c. Capillarity d. Surface tension e. both (a) and (b)
386. Which of the following methods in welding uses a pool of molten metal?
a. Carbon arc welding b. TIG welding c. Submerged arc welding d. MIG welding e. Thermit welding
388. Which of the following fuel has little tendency towards detonation?
a. Benzene b. Iso-octane c. N-heptane d. Alcohol e. None of the above
389. Which mechanical property a metal should possess to enable it to be mechanically formed?
A. ductility b. malleability c. elasticity e. machinability e. None of the above
390. The strain energy stored in a spring, when subjected to maximum load, without suffering
permanent distortion, is known as
a. Strain energy b. Resilience c. Proof Resilience d. Proof stress e. None
391. How many of the following statements may be false?
1) The index that normally reflects the nature of flow in a duct is Reynolds number
2) One ton of refrigeration is equal to 12000 btu/hr
3) Pressure drop in air duct is influenced by shape of the duct
4) The viscosity of hydrogen increase with increase of temperature
A. One only b. Two only c. Three only d. All the above e. None of the above
392. Moment of inertia of a triangular section of base (b) and height (h) about an axis passing through its
vertex and parallel to the base is __________ than that passing through its C.G. and parallel to the base.
a. Nine times b. six times c. four times d. one-half e. one-third
394. Which law states that change in internal energy of a perfect gas is directly proportional to the
change in temperature?
a. Avagadro’s law b. Gay-Lussac law c. Joule’s law d. Newtonian law e. None of these
395. A taper provided on the pattern for its easy and clean withdrawal from the mould is known as
A. machining allowance b. draft allowance c. shrinkage allowance d. distortion allowance
e. None of the above.
402. CPM and PERT deals with determining the status of the project
405. Dalton’s law of pressure total pressure equals sum of partial pressures.
406. As per Avogadro’s hypothesis molecular wt of all gases occupy the same volume under same
conditions of temp and pressure
412. Efficiency of diesel engine as compared to petrol engine under same rated load (high)
415. Pour point is (min temp at which a liquid flows at set condition)
426. If a block of ice floating in a tub of water and gets melted then what will be the level of water a.
falls down b.rises c. remains the same
429. Choking in compressor means change in mass flow rate with proportional to Pr ratio, change in
mass flow rate with inversely proportional to Pr ratio, fixed mass flow rate regardless to Pr.
432. How will you find the unburnt mixture in exhaust gas?
a) Analyzing CO b) Analyzing Oxygen.
440. An adiabatic compression is one in which no heat enters or leaves the system.
441. What happens if the refrigerator doors are kept open? The room will be warmed up gradually.
442. In break even analysis, profit occurs when sales revenue >total cost.
444. A material piece weighs 2.5 kg in air and 3 kg, when immersed in water, then sp.gr is
445. A body of sp.gr 7 is immersed in mercury of sp.gr 13.6. What percent of the body will be immersed
in water? 0.515.
446. 1 tonne of refrigeration is the cooling effect produced when melting one tonne of ice
450. If we use petrol in diesel engine lot of fuel will remain unburnt.
451. In V belt drive contact is made on a) bottom b) sides c)bottom and sides
452. The intake of air in an air compressor can be had from
a) An area nearby coal yard. b) An area nearby a cooling tower. c) A room in which conditioned air is
maintained at 20°C. d) Atm air maintained at 1°C
461. Kelvin plank law deals with 1) Conservation of work into heat 2) conservation of heat into work
464. High cutting speed is obtained while machining 1) HSS 2) carbide 3) CBN
469. Spherical cast iron is getting from Grey cast iron by adding _________? Mg
474. In centreless grinding, the grinding wheel and the regulating wheels rotate in the same direction.
475. Centridal distance of a semi circle 4*r/3*pi
477. Which chart takes care of control attributes: P chart, C chart, R chart
478. Fixture is used for holding the work piece without disturbing the tool path
480. Order of transmission in a car: EFCPD (Engine Flywheel Clutch Propeller shaft Differential)
490. What path does double slider crank mechanism follows. (Check if it is Elliptical).
491. Ratio between Brake horse powers to the energy supplied. Brake thermal efficiency
492. Two emfs E1 and E2 are given. Among two lengths one is given. Be clear with the relation
between ratios of emfs to the lengths across.
505. Heat transfer is based on which law (zeroth, first, 2nd, kirchoff)
506. In refrigeration where will temp be max? Between compress and condenser
509. How will u pump sewage water i.e. which pump? Lobe pump
514. If refrigerator is opened in a room, fan is also on. What will happen to room temp? Temp
increases.
518. For a cantilever beam with uniformly varying load, shape of bending moment curve is
a)parabolic b) hyperbolic c) straight line d) cubic.
520. For 1st order lever, mechanical advantage is a) <1 b)>1 c) =1 d) none.
521. 18:4:1 in H.S.S represent a) 18tu : 4vn : 1 cr. Other choices r just interchanged.
523. Thermal efficiency of I.C engines will be a)20-25% b)30-35% c)60-75% d) 45- 55%.
524. when a mass is supported by spring of spring constant k, which is cut in 4 equal pieces and the
connected in parallel way the equilent spring constant is a)k/4 b) 16k c) 64k d) k.
525. when a mass is supported on roof of a elevator and elevator moves with an acceleration of 4.9 m/s2
shows a spring reading of 15kg, then the weight of the body is a) 10 b) 15 c) 30 d)20.
526. Mass production of bolts and rivets is by
a .hot extrusion b .forging c .cold heading d .cold peening
528. How r bolts and nuts manufactured? A. head stamping b .cold extrusion c .cold peening d .forging
529. Euler’s formula is used for column of length a. >80 b. <80 c. >90 d. >110
530. If a body weighing 40kg floats in water with 40% of volume immersed, the sp.gravity of the body
is a. 1 b. 0.16 c. 0.25 d.
531. Axial claw clutches a. Disengages b. engages c. engages only with load d. operates only with load
532. If center distance of a involutes mating gear changes then the pressure angle
a. Increases b. decreases c. remains unaltered
533. Normalising is
A. heated above critical temp and cooled in air. B. heated above critical temp and quenched in oil
C. heated below critical temp and cooled in air
535. The best suited material for permanent magnet a. Alnico b. silicon
537. To have a const.velocity ratio the two gears should have (or) angular velocity of the gear will
remain the same if the .......... cuts the line joining ........ at a fixed point law of gearing
538. Which of the following is a loose running fit a. h6f6 b.h6e6 c. h6d6
541. Specific speed in a turbo machine depends on a. geometric shape, b. size, c. head, d. all the above.
545. Melting point of ice changes with a. increase with pressure, b. increase with pressure ratio.
548. When a helical compressive spring is subjected to axial compression load, the stress induced in the
spring will be a. tensile, b. compressive, c. shear. d. none
549. For a bar element if area, length, and stress are doubled the elastic strain energy will be
A. Half b. doubled c. 4 times d. 8 times
550. For a punching die, 2mm thick sheet, dia. D, force f, the shear force is 8800.
552. What type of thread is used in lead screw of a lathe A. acme thread B. V C. Square D. buttress
553. Wear allowance of a go nogo end plug gauge is given for a.. go end b. nogo end
554. Internal spur gears can be made by using a. Gear shaping b. slotting c. Gear hobbing
555. Height of the capillary varies with A. Increase with increase in dia of tube B. increase with increase
in sp. weight C. increase with decrease in dia D. increase with decrease in sp. weight
556. A bolt of nominal diameter 33mm the stress of 100N/mm2 the safe load is
A) 60 KN b) 100 KN c) 160 kN.
557. A cylinder with in 1% of the tolerence capacity limit, the permissible tolerence in height and radius
are is 0.2% radius and 0.25 height.
562. An elevator is moving up with an acc. of 4.9 m/sec2 a body weighing 15 kg is attached with spring
balance. What is the value in the spring balance a. 10 b. 15 c. 20 d. 30
565. If the body is 40% immersed in water what will be its specific gravity
566. The temp at the three edges of a square shaped body is 0 C and on the fourth edge is 100 c find the
Temp at the centre of the square a. 25 b. 100 c. 50 d. 0.
576. Cutting speed of carbide tools while cutting low carbon steel
a) 40m/min b) 250m/min c) 500m/min d) 80m/min
578. The circularity that can be achieved by finish turning on a standard centre lathe is
a) 0.005-0.008mm b) 0.0-0.08mm c) 0.1-0.2mm d) 0.2-0.3mm
583. The displacement accuracy which can be achieved on a jig boring machine
a) 5/µm b) 50/µm c) 100/µm
589. In a right angle transmission by helical gears, the hands of the helix of the gears are
a) Same b) opposite c) Immaterial d) none
591. Ball bearings are not generally used in crank shafts of automobiles because
a) of high cost b)of high speed c)cannot be assembled d)none
592. Most hydrostatic bearings normally work under
a) Constant flow system b) constant pressure system
c) Constant temperature system d) constant volume system
597. When ice which is floating in water, melts, does the level to water
a) go up b) go down c) remain the same.
605. Effect of increase of outside diameter of a helical compression spring on its rigidity is
a) Increased rigidity b) decreased rigidity c) no effect d) dry friction
614. A 6kg ball is suspended from two wires of equal length. The angle between the wires is 90
degrees. What is the tension in each wire? a. 58.8N b. 41.6N c. 29.4N d. 83.2N
615. A 523 kg experimental rocked sted can be accelerated from rest to 1602 km/h in 1.82s. What net
force is required? a. 4.6X106N B. 4.6X105N C. 1.6X106N D. 1.3X105N
616. A force that averages 984N is applied to a 0.42kg steel ball moving at 13.8 m/s by a collision that
lasts 0.027s. If the force is in a direction opposite to the initial velocity of the ball, what is the final
speed of the ball? A. 77.1m/s B. 63.3m/s C. 13.8m/s D. 49.5m/s
617. A stone initially at rest is dropped over the edge of a very tall building. Taking g as 10m/s2, what
was the change in the speed of the stone building during the 4th second?
A. 10m/s B. 30m/s C. 15m/s D. 40m/s
618. How long will it take a 2000w motor to lift a 320kg container vertically upwards for 26m?
(g = 9.8 m/s2) A. 29s B. 6.3s C. 4.2s D. 4.1s
620. What is the force exerted on a submarine window of 2m2 area, if the submarine is at a depth of
2km below the surface?(the density of sea water is 1.03X103 kg/m3)
A. 4.04X107N B. 4.04X104N C. 2.02X104N D. 2.02X107N
621. A body partially floats with 2/3rds of its volume under the surface of a fluid. If the density of the
fluid is X kg/m3, what is the density of the body?
A. 3/2 X kg/m3 B. 2/3 X kg/m3 C. 14.7 X kg/m3 D. 0.15 X kg/m3
622. How many of the following statements are true:
A. the buoyant force on a body depends on the shape of the body
B. The buoyant force on a body always acts in the same direction
C. the buoyant force on a body depends on the mass of the body
D. The buoyant force on a body depends on the density of the fluid surrounding the body
A. only one B. only two C. only three D. only four
625. A power station generates 500MW of power and exhausts 800MW as waste heat into the
environment. What is the efficiency of the power station?
A. 61.5% B. 38.5% C. 62.5% D. 23%
626. How long does it take a 350W coffeepot to boil of 0.7L of water initially at 100°C.
The latent heat of vapourisation of water = 2.1X106 J/kg.
A. 6.1 min. B. 7.0 min C. 3.9 min. D. 3.1 min.
627. A 16 ohm resistor and 8 ohm resistor are connected in series across a 12V battery. What is the
voltage across each resistor respectively? A. 8V , 4V B. 4V , 8V C. 12V, 12V D. 6V, 6V
628. How many of the following statements regarding sound are true?
A. Intensity depends on the square root of the amplitude
B. Loudness only depends on the intensity of a sound
C. The pitch of a sound depends on the frequency
D. Sound is reflected whenever a change in acoustic impedance is encountered
A. Only one B. Only two C. Only three D. All four
629. How many of the following statements regarding light are true?
A. Light travels in a straight line even when it crosses between two media of different refractive index
B. Infrared light has longer wavelength than ultra-violet light
C. Light can behave both like a ray and like a particle
D. It is possible to get a real image with a concave lenses
A. Only one B. Only two C. Only three D. All four
631. Convert volumetric to gravitational, relative volume of each constituent of flue gas
a. %mw b. xmv c. me d. xsw e. %sw
632. Which is correct for reversible polytrophic process?
a. temperature constant b. density constant c. volume constant
d. entropy constant e. same heat transfer
635. Under ideal condition, isothermal, isochoric, adiabatic and isobaric are
a. static b. dynamic c. quan-static d. stable e. thermodynamic
637. If Q1 is the heat in source, Q2 is the cold sink for heat pump then COP
a. Q1 / (Q1- Q2) b. Q2 / (Q1- Q2) c. (Q1- Q2) / Q1
640. for same power, same speed, flywheel of petrol and diesel engine are
a. smaller b. greater c. equal d. none
650. In pinion and gear design, the design must be made by a. gear b. pinion c. both
657. In an ideal gas compared to a real gas at very high pressure occupies?
658. Kinetic theory of gases assumes that collisions between the molecules are?
659. The condition of perfect vacuum that is at absolute zero pressure can be attained at?
664. When crude oil heated Which Hydro carbon comes first?
668. Scale formation on the surface of the boiler tubes due to?
681. In what angle does an object thrown height will travel the longest distance?
683. The coupling is required to connect two parallel shaft distance between the shaft is small and
variable?
686. To protect from thrust which type of follower is used? Roller follower/mushroom or spherical
follower.
689. For shock resistance and vibrations we use malleable cast iron.
693. In a uniformly distributed load of 6n/m over a 5 meter length simply supported beam, the value of
B.M at the point where shear force is zero (17.5/22.5/55/75)
701. The key used in the gears for transmitting power (flat/saddle/spline/square)
715. At what angle in the valve timing, Diesel engine injection occurs? 20 degree before TDC
716. Name any one non destructive test? laser beam/ utrasonic
719. Name any one Gear material? cast iron , phosphor bronze, alloy steel , carbon steels
722. Reynolds number range for laminar flow –? for flat plate < 5*10^5 ,for pipe < 2000
723. Nusselt (for natural) number is function of which number? grashoff and prandtl number
725. What is the function of cutting fluid? cool the tool and the work piece/lubrication/ improves
surface finish
726. Dual cycle combination of which two cycles? otto and diesel cycle
729. Frequency of a system is 3 Hz then find the speed in rpm? 180 rpm
730. For which gear shafts are co-axial? reverted gear train
735. Ignition quality of the diesel fuel oil is measure by index no is called
A. octane b. cetene c. calorific value d. carbon no
742. ------------ gear train is one in which each shaft call as one wheel only
a. simple b. compound c. epicyclic d. none
746. In ----- moulding green sand is generally used A. floor B. late C. bench D. it
747. With increase in cutting speed power requirement is
a. decrease linearly b. remains constant c. increase linearly d. Unpredictable.
748. What will be the locus of a point on a thread unwound from a cylinder?
a. involute b. helix c. straight line d. circle
753. H7-h6 is
a. clearance fir b. transition fit c. interference fit d. sliding fit
755. The function of ---------------- is to transform input motion of rotation in to out put motion of
translation
a. screw b. bolt c. nut d. key
756. the most important element which control the physical property of steel is
a. silicon b. manganese c. tungsten d. carbon
757. Austempering is the heat treatment process used to obtain greater
a. hardness b. toughness c. softness d. brittle ness
758. Zeroth law of thermodynamics, Joule’s law, Newton’s 2nd law of rotary motion, Third law of
thermodynamics
760. If a body is moving in a circular path, a force comes into the path, which acts along with the radius
of the circular path and is directed towards the centre of the path, what is the force?
761. Gravitational acceleration at a place is 6 times the value of gravitational acceleration at earth. The
weight of the body at that place will be
762. The acceleration of a particle moving with simple harmonic motion (SHM) is maximum,
764. In case of exhaust silencer of a petrol engine is partly chocked it is likely to result in
768. For any thermodynamic process the area under T-s curve represents
769. When the load on CI engine decreases its efficiency increases. This is due to
781. In cold and hot rolling which cannot be done? Hollow circular section
784. Crank rotates at 4pi radians per second, crank radius 10 cm piston velocity?
789. For chipless machining non conventional method used ------ Laser beam machinig
794. Circle which takes the basic rolling action as that of the gear? Pitch circle
805. Water droplets falling down assume spherical shape due to ------------ property
a) cohesion b) surface tension c) adhesion
809. Ina flour mill, -------- type of drive is used flat belt drive
815. Cast Iron is used in machine bed ways for Damping Vibrations
819. The material whose property is same in all the materials is isotropic
839. Distance between bore of cylinder and connecting rod bearing is called
843. DIN is formed from which country?- Germany, US, Austria, Japan
862. Differential and gear box, between them which gear is used
865. Shaft, pulley, key is designed on the basis of keeping key weaker.
866. Brazing is used for what materials
867. 60cm wheel, 40cm wheel. First wheel moves distance with 280rev., then no of rev. then no. of rev.
second wheel moves for same distance
873. Annealing is used for improving following property. All of the above
878. Radial distance below the PCD and base circle is ______________
886. Second time of the clock increases 5m in day. What should be done on the length of the pendulum
bar
887. The difference between the dry bulb and wet bulb temperature
900. After the removal load the body does not comes to original stage instantaneously – it implies
904. The shafts are connecting two intersecting axis universal coupling
921. Hardness and toughness is considered while selecting a tool for m/cary and material
922. For transmitting power from gear box to wheels which joint is used-universal joint
939. In a drawer, 5 white socks and 8 black socks are there. To draw one pair of socks, minimum no of
socks that has to be drawn? Ans.3
940. Radius of a cylinder is increased by 30%, then increase in volume will be -------(height is
constant).Ans.69%
941. The mass of a ball is 250 g and velocity is 10m/s.The potential energy at maximum height is
Ans.12.5 [1/2*M*V2]
943. A thin wire is subjected to tensile stress. There is no increase in resistance. Then what will
happen? Ans. Temperature remains the same.
945. Stoichiometric combustion requires how many percentage of excess air? Ans.0%
946. The shape of the BMD in a cantilever beam will be Ans. Triangle
949. If ‘a’ is the coefficient of thermal expansion and E is young’s modulus, the-----
952. Cavitation occurs when Actual pressure of fluid < Vapour pressue of the fluid
953. At what temp, degree Celsius and Fahrenheit values are the same? -40 degree C
957. In a Spring damper system, mass is made of quartz. What happens to frequency? 4
973. If a body is at -10 degree C (ice) and if it is to be converted into saturated vapour ,how much heat is
necessary?
974. According to Newtonian Law, shear stress is directly proportional to velocity gradient.
977. What is the type of failure in Key that is used in Flange Coupling?
981. if Inlet air temp increases, efficiency(petrol engine) increases but compressor efficiency decreases
True
985. Which cycle uses two isentropic and two isothermal processes
986. A material is loaded still yield point and the load is removed.
a. Increase in yield stress b. Decrease in yield stress
c. Unchanged yield stress d. Reaches UTS
987. A thin wire is subjected to tensile load. Temperature is same. The resistance remains constant.
987. Match
Kirchoff law - electrical circuit
Dalton’s law - partial pressure
Hooks law - elasticity
Joules law - work equivalent to heat
994. In a centrifugal pump installation while starting, the position of delivery valve is
a. fully open b. fully closed c. half opened. d. more than half open
995. An air vessel is provided at the summit in syphon to
a. regulate the flow b. increase discharge c. increase velocity d. avoid an interrupt in the flow
996. a material which recovers fully after unloading but not instantaneously is known as
a. plastic b. elastic c. partially elastics d. inelastic
997. The loss of strength in compression with simultaneous gain in strength in tension due to over
loading is known as a. hysteresis b. inelasticity c. creep d. boeschinger effect
1001. The angle of projection of a projectile is double the angle of inclination of the plane on which a
particle is projected. The ratio of time of flights on the upward inclined plane and downward inclined
plane will be equal to
a. 1/cosa b. 1/2cosa c. 1/sina d. 1/2sina
1003. While designing for screw threads care should be taken to provide adequate length of engagement
for the screw and nut threads so as to prevent failure of threads in
a. tension b. compression c. torque d. shear
1006. A babbit is
a. a eutectic of iron and iron phosphate b. a gadget for measuring volume c. a measure of magnetic
induction produced in a material d. antimony bearing lead or tin alloy(ans)
1010. A circulating water pump of a condenser is of the centrifugal type and directly connected to a
three phase induction motor running at 900 rpm. The pump delivers 30000 litres per min. against the
dynamic head of 10m. The horse power of the motor required to drive the pump would be
a. 20-30 b. 40-50 c. 50-60 d. 60-70
1011. As per Indian boilers regulations the type of joint preferred for longitudinal joint is
a. welded joint b. welded joint which cover plate c. riveted lap joint d. riveted butt joint
1014. A shaft is subjected to a torque T and bending moment M. the equivalent twisting moment would
be: a. (M2+T2)1/2 b. (M2+4T2)1/2 c. (4M2+T2)1/2 d. (M2+T2)1/2 + (m/2)1/2
1015. The average values of modulus of rigidity for Al, brass, copper, nickel and steel in descending
order is Al, Ni, Br, copper, steel
1017. A solid shaft of 100mm dia transmits 100HP at 450/PI rpm. The torque in kg, m on the shaft
would be a. 250 b. 375 c. 500 d. 750
1019. In order to avoid interference for 20 pressure and teeth minimum of teeth should be
a. 8 b. 12 c. 16 d. more than 18
1023. Jaw clutches a. cause shock loads when engaging b. get disengaged at high rpm c. get
disengaged in reverse direction d. are friction clutches which generate heat when engaged
1024. A body which does not contain voids or empty spaces is known as
A. continuous body b. an isotropic body c. heterogeneous body d. crystalline body
1025. The limiting load beyond which the material no longer behaves elastically known as
A. breaking load b. limiting load c. load bearing load capacity d. elastic limit
1029. a master gauge is a. used by masters b. used by all mechanics c. a standard gauge checking
accuracy of gauges used on shop floors d. a gauge used by experienced technician.
1030. In centre less grinding the work piece advanced by a. push given by operator b. hydraulic force c.
force exerted by grinding wheel d. force exerted by regulating wheel (ans)
1031. In climb milling is work moves in the same direction as rotation of the cutter.
1033. A 250mm diameter is turned at a cutting speed of 20m/min feed 0.5mm per rev. of spindle at a
spindle speed of 25rpm now if the dia of workpiece is double and spindle speed is also double the time
taken to turn the job will be
a. Four times the original time B. double the original time
C. no change in turning time D. one fourth the original time
1034. The passage way of bringing the molten metal to the mould cavity is known as:
a. piping system b. loaming system c. gating system d. entry system
1035. A third flask sometimes used between cope and drag is called
a. riddle b. middle c. fillet d. cheek
1036. Shot blasting is a. process of cleaning moulding sand b. process of cleaning core sand
c. process of supplying blast of hot air to cupola d. process of cleaning casting
1038. The method of testing hardness by brinell test is based on the principle of
a. indentation b. penetration c. rebound d. scratching
1039. In thermit welding heat is generated
A. from combustion of gases b. electric arc c. reaction of oxygen with metal
D. chemical reaction involving finely divided al and iron oxide.
1040. Ultrasonic machining is best suited for
a. non ferrous metal b. amorphous solids c. brittle materials d. dielectrics
1041. In EDM the material of the tool is a. satellite b. diamond c. carbide d. high speed steel
1052. The process of cutting thin gears from metal sheets is known as
a. extruding b. stamping c. sintering d. rolling
1054. The term CLA is used in connection with: a. surface hardness b. surface finish
c. stresses in a component d. average speed of a gear.
1055. Dressing in foundry practice is the process of addition of chemicals to the molten metal to
improve its fluidity
1056. A steel piece after hardening is heated to 300C and then cooled in oil. The property imparted to
the steel piece will be: a. softness b. toughness c. hardness d. annealing
1059. If (2n-1) divisions on the main scale are equal to n divisions on the vernier scale and if S is the
value of the smallest division, then least count would be:
a. 2n/S b. S/2n-1 c. S/2n d. S/n
1060. Pipes are insulated so that a. the may not break under pressure. b. There is min. corrosion c. They
can withstand higher fluid pressures d. Heat loss from the surface is minimized.
1063. What is the cutting speed of HSS single point cutting tool while machining CI a.6m/min
b.11m/min c. 22m/min d. 33 m/min
1065. Subsonic velocity occurs when a. throat b. convergent. C. divergent d. convergent divergent
1066. Bombers are used in a. turbojet b. ramjet c. pulse jet d. turbo propeller
1067. The gradient of any hardened steel. a. marten site. B. pearlite c. austenite
1071. Moment of inertia of solid sphere a. 1/2 Mr2 b. 2/3 Mr2 c. 1/8 Mr2
1072. 1 stroke=--------m^2/sec.
1080. The function of control rod a) absorb the Neutrons b) to prevent the radiation
1081. The fuel used in nuclear thermal power plant a) uranium b) plutonium c) thorium
1089. The body rotates around a fixed axis the motion will be-------- rotation, circular,
Translation, rotation and translation
1090. Min dia of hole that can be punched…….4TFs/Fc, 4TFc/Fs
1092. In which gear the min axial thrust is available…..worm, herringbone, spur, helical
1093. worm gear commonly used due to ……high speed reduction, easy to M/F, low cost,
low power consumption
1095. Use of economizer……..extract heat from flue gas, increase the efficiency
1097. The value means in value Engg…………Total cost of the product, etc
1099. Steam bleeding is done to ….extract steam from turbine and heat the feed water
1101. When rotary compressors are used …………..high discharge low pressure, etc…..
1103. When walking on the ice slippery is due to ……..no friction, ice breakage, ice chill, Pr
Increases melts the ice
1104. Stainless steel contains for corrosion …..Chromium, Cu, Zn, Ni.
1105. Metal regains its original position after unloading but not instantaneously……elastic,
Plastic, anelastic , partially plastic
1106. For ductile material which theory of failure is used……..distortion energy theory, max
principle stress theory
1109. Standard time ……a) operational time+ allowance+ ideal b) normal time + allowance
1111. The least amount of material removed in …….lapping, honing, super finishing, grinding
1112. Glazing of grinding wheel due to …….break of bonds, break of abrasive particles,
wear of abrasive particles
1113. The size of inlet valve compared to exit valve …….less, more, depending on the applications
1116. In which axis moment of inertia is less…….vertical, horizontal, central, it is not dependent on axis
1117. In case of forming the stress value is ……above yield point within ultimate strength,
within proportionality, etc
1123. which one is correct fit indication …….50 H8/g7, H8/g7, g7/H8, H8/g7-50
1124. in which place the millimeter reading is available……Thimble, barrel , anvil, ratchet
1126. In case of super sonic flow …….the velocity increase with decreasing area, the V
Increases with A increasing, there is no change, none of this
1127. More power required in centrifugal compressor due to …..Air leakage, air I water,
Heavy liquid,
1128. Gas behaves as ideal at ……..vacuum, high Pr & High Temp, critical temp
1131. Entropy changes with ……internal energy change, Pr & Vol change, change of state, change in
temp
1132. In which process max work can be obtained….Const Vol, Const Pr, Const Temp, Const Entropy
1134. Reverse joule cycle is ……….(bell coalman cycle, Rankine cycle, bray ton cycle
1138. Product layout used in batch prodn, continuous prodn, efficient use of machines.
1139. The locus of the point on the circumference of the circles rolls along the straight lines without slip
cycloidal path, involute, epi cycloid
1141. The basic hole is one…… lower deviation is zero, upper deviation is zero
1143. In selective assembly, type of fit used……..string fit, wringing fit, free fit, press fit
1144. While tapping, the size of the hole is drilled…….. Equal to thread dia, less than thread
Dia, more than thread dia
1146. Which one has high wave length……. Alpha rays, beta rays, x rays, uv rays
1148. force which acts along the radius of the circle and away from the centre is _____
a. centrifugal b. centripetal c. radial d. axial
1151. Shaft is subjected to ______ a. torsion b. bending c. axial d. any of the above
1152. Standard metric pitch of M14 is ____ a. 0.80 b. 0.85 c. 0.9 d. 0.95
1153. The cutting tool used for machining HSS is ____ a. carbide b. CBN c. satellite
1154. The parameter for process variation is _______ a. Cp b. Cpk c.pp d. ppk
1156. What are TPM, PPM, PPM (regarding quality) and SPM?
1157. What are BIS, APQP, ISO and PPAP?
1158. The point angle of drill is _____ a.120 b. 119 c. 118 d. 117
1159. Outer dia – (2 * module) = ________ a. inner dia b. addendum c. dedendum d. PCD
1160. Draw the symbol for Symmetry, concentricity, Perpendicularity and Circular runout.
1162. If spring is cut into two pieces the stiffness will _______ (double)
1172. Question on section modulus, Zeroth law of thermodynamics, TTT and stress strain diagram.
1175. The max strain energy stored in the body is called as ___________(Resilience)
1176. About proof resilience (max load acting on the spring ---)
1178. Another Name of Bell Coleman cycle (ans :reverse carnot cycle)
1185. What type of material can be machined using HSS tool?(Choice : MS ,Al, Brass)
1186. A combination of pearlite and ferrite gives which type of iron?(Choice: Hard / Very hard / Soft / )
1187. Cutting fluid used for machining alloys (choice: Water, Heavy oil, Sulpurized mineral oil, Soluble
oil )
1193. The power produced by a Single acting engine is as compared to Double acting
A. engine B. Half C. Double D. Same
1198. If the carbon steel is heated above it’s critical temp what will happen in it’s grain size
A. Relatively decreases B. Rapidly increase C. Increase and then decrease
1202. If we apply a transverse load on a beam what type of moment will be created?
1208. The ratio of heat available in the furnace to the heat required to produce steam?
1211. The length of divergent portion of the cone when compared to the convergent portion in a venturi
meter?
1212. One molecule of oxygen is how many times heavier than one atom of hydrogen.
1214. For aligning two parallel shaft which type of coupling used?
1217. Torsional vibration occur when particles of body moves in which direction
1218. When two rotors mounted at the end of the shaft how many nodes will occurs?
1221. In 24 -40 meter/min cutting speed using HSS cutting tool which type of material can be machined.
1227. The difference between planner and shaper is that in former case
a) tool moves over stationary work b) tool moves over reciprocating work c) tool can machine internal
as well as external details d) both tool and job reciprocates e) tool is stationary and job reciprocates
1232. In which type of milling operation the chip is cut off at thinnest place and the chip thickness
increases along chip length
a) Up milling b) down milling c) end milling d) climb milling e) key way milling
1235. Gantt chart provides the information about a) material handling b) proper utilization of manpower
c) production schedule d) efficient working of machine e) all the above
1249. In a cantilever beam point load is applied on free end, where failure will accure
1252. Type of hatching is given you having to identify the material - ref: m/c drawing book
1253. Study about combination die, compound die and progressive die.
1255. Free vortex region is not suitable for low hub-tip ratio compressor stage because:
a. reaction near the hub will be low b. Reac. near the hub will be high
c. Specific work near the hub will be low d. relative velocity will be very high
1264. The rorometer uses the following principle for fluid flow measurement:
a. Const. area and variable differential pressure
b. variable area and variable differential pressure
c. variable area and variable viscosity d. variable area and constant differential pressure
1266. if a water pump develops 10 m head on earth, what would be its head if it is operated on moon:
a.10/6 m c.>10 m b. 10 m d. none of above
1269. For determining the fatigue life a. Max. Principal stress is the factor b. Max. Compressive
stress is the factor c. Max. Tensile stress is the factor d. Max. Shear stress is the factor
1270. 2 identical specimens one with rough surface finish and other with fine finish, having identical
small notches are subjected to same reverse bending load:
a. life of smooth specimen is more b. life of rough specimen is more
c. both will have same life d. lives are not related
1271. Rotary compressors are used for delivering:
a. small quantities of air at high pressure b. large quantities of air at high pressure
c. small quantities of air at low pressure d. large quantities of air at low pressure
1272. In an axial flow compressor the ratio of pressure in the rotor blades to the pressure rise in the
compressor in one stage is known as:
a. work factor b. slip factor c. degree of reaction d. pressure coefficient
1274. A moderator, in nuclear power plants, is a medium introduced into the fuel mass in order to
a. slow down the speed of fast moving neutrons b. control the reac.
c. reduce the temperature d. extract heat from nuclear reaction
1287. __________ pump is used when the viscosity of the liquid is more.
1301. What will happen after Nuclear Fusion? to atoms join together to form on Nuclei
1304. In a room refrigerator operating at a full efficiency if kept open what will happen to room
temperature?
1305. In a two tank A & B having 2 liquids Water & Kerosene .The tank A has two 1cm dia outlets and
tank B has one 2 cm dia outlet. Which will empty soon?
1311. After the emission of alpha particles Neutron to Proton Ratio is_______
1314. Wire of Resistance 10 ohm, Length is increased 3 times, Same Density, What is new resistance?
(Depends on L/A ratio) Ans. 90 Ohms
1315. Transformer Primary – 4000 Turns, 2.5 kV, and Secondary – 250 V, what is no of turns in
Secondary coil? (Ans. 400)
1316. Mean coil dia of the spring is 0.8 cm, No of turns 5, wire dia 0.01cm, Length of the coil
is_________?(Ans. 12.6 cm)
1317. Valve used for supplying oil to the burner in the boiler
Isolation Valve b. Needle Valve c. Non Return Valve d. Relief Valve e. Butterfly Valve
1319. Water is flowing in a 5 cm dia pipe line at a velocity of 10 m/s, the pressure drop across orifice
meter in a water line is 2 cm of Hg. If the mercury is replaced by a liquid and immiscible with water the
pressure drop will be ________(Ans 17 cm)
1335. Increasing hard ness by cold working a. work hardening b. Cold hardening c. hot
hardening
1336. Which can be used for high speed application a. hss b. cementite carbide
1350. When the ice melts what is the water level remains same
1367. When white cast iron is cooled the product formed is a. malleable ci b. spheroidal c.
Gray ci
1368. Case hardening done for a. low carbon steel b. high c steel
1372. To reduce knocking in si engine is to add a. tetra ethyl lead b.. Methyl iso…
1373. Heating steel above appear critical temp and cooled in air is normalizing
1377. Coolant is used to a. increase e tool life b. Reduce heat during machining
1394. A pair of dice is thrown. What is the probability of getting sum of odd numbers?(Answer - 0.5)
1400. Max. deflection of a beam with U.D.L in simply supported beam WL3 / (48EI)
1401. Coupling of right hand & left hand thread turn buckle.
1404. 8 men and 4 women 4 task finished in 16 hours. 4 men 8 women 7task finished in 32
hours. How many men are required to commit 3 tasks in 8 hours? 16 men
1405. In a class 28% are from other states. Of remaining 25% are from rural areas. What is the
percentage of students who come from urban area? 51%
1406. A tractor costs rupees 2 lakhs. Given a loan at 16% rate of interest at margin of 25%. He pays
Rs.40, 000 after one year. How much is the balance. Rs.1, 34,000
1407. A train is moving away from the stationary man at 33 m/s with a frequency of 1200 Hz. What is
the observed frequency if the velocity of sound is 330 m/s? 1090 Hz
1410. If a principal amount is doubled in 8 years in compound interest, what is the ratio of interest? 9%
1412. Damping force in freely vibrating with negligible velocity and directly proportional to
displacement.
1416. Gear hobbing is used for all type of gears not bevel gears.
1417. Front and side view of an object is triangle. Cone and pyramid.
1419. Boat running in a still water at 15km/hr upstream crosses 40km (refer)
1420. Velocity of a planet when it is nearest to star is 10 km/s farthest velocity is 2.5km/hr. ratio of the
farthest to nearest distance is 1:4.
1423. In Rockwell hardness machine in which scale maximum load can be applied A, B , C 50 an 150
kg C scale
1424. What is Trepanning? Making large holes by removing metal along the circumference of a
hollow cutting tool
1425. Which is important for drawing a gear a. base circle b. pitch circle c. all the above.
1426. Hardenability means Ease with which the material can be hardened
1432. Difference between nut and screw. Nut can be used in through hole but Screw can not be used
in through hole & Nut can be used only along with the bolt but screw need not be.
1433. What is stud? Used for aligning components. It is screwed to one of the part
1434. Normal value of voltage in spark plug & distributor function. 10 to 20000 V
1435. What do you understand by Wankel engine? Wankel engine – Rotory Engine (No Pistons)
1437. In which of the following work piece moves and tool remains stationary
a. Planing b. shaping c. milling d. drilling.
1438. Which tool has multiple cutting edges? Miller / Broaching tool
1440. Meaning of overdrive. Speed of the driven member is greater than the prime mover
1441. What is ISO 9000 standard for quality. Quality Management & Quality Assurance standards
1446. To get deep hole in less tensile strength material which drilling is preferred step drilling
1448. In which part of the lathe the honing operation is done? a. chuck b. lathe bed c. tail stock
1450. Which diameter is kept in mind while roughing the top face of gear teeth?
a. pitch b. base circle c. addendum d. deddendum.
1452. What is lapping? Super finishing process to obtain good surface finish
1453. The axial stress on a member which is subjected to a sudden load when compared to load applied
gradually is a. same b. double c. half d. quadraple
1455. Austempering affects what property of material. Improve toughness & Ductility
1459. Manometer sensitivity of a given area depends on cross section area at that point
1464. Which material has the highest Cp value? a. air b. water c. copper
1466. An object weighs 3kg in air, 2.5kg in water, what is its density?
1467. Time study deals with Time taken to complete one operation
1469. CPM and PERT deals with determining the status of the project
1472. Dalton’s law of pressure Total pressure equals sum of partial pressures
1473. What is Avogadro’s hypothesis Molecular wt of all gases occupy the same volume under same
conditions of temp and pressure.
1479. Efficiency of diesel engine as compared to petrol engine under same rated load High
1482. What is pour point? Min temp. at which a liquid flows at set condition
1483. Zeroth law of thermodynamics when two bodies are in thermal equilibrium individually with
the third body the two bodies are in thermal equilibrium with each other
1490. If a block of ice floating in a tub of water and gets melted then what will be the level of water
a. falls down b. rises c. remains the same
1492. Heat transfer takes place as per a. Second law b. First law c. Zeroth law
1493. Choking in compressor means fixed mass flow rate independent of the pressure ratio
1494. Formation of frost in refrigerator Immaterial
1495. Supercharging is the process of increasing the density of the inlet charge
1496. How will you find the unburnt mixture in exhaust gas? Analyzing Oxygen
1504. An adiabatic compression is one in which no heat enters or leaves the system
1505. What happens if the refrigerator doors are kept open? The room will be warmed up gradually
1507. In break even analysis, profit occurs when sales revenue >total cost
1508. A material piece weighs 2.5 kg in air and 3 kg, when immersed in water, then sp.gr is
2.5 / 3
1509. A body of sp.gr 7 is immersed in Hg of sp.gr 13.6. What percent of the body will be immersed in
water? 0.515
1510. 1 tonne of refrigeration is the cooling effect produced when melting one tonne of ice
1514. If we use petrol in diesel engine lot of fuel will remain unburnt
1515. The intake of air in an air compressor can be had from Atm air maintained at 1°C
1516. If v=220V, I=25A, power factor=0.8, freq=400Hz. If the motor runs for 3 hrs, what is the power
consumed?
1519. When salt is added to water, what happens to its freezing point? Increases
1520. What motor do they use in railway engines for traction? DC Series motor
1523. If the barometer shows 300mm Hg, what is the absolute pressure?
1524. Which gear type does not have axial thrust? Herringbone
1525. Which of the following is not a thermal radiation law? Lamberts law
1528. Which of the following is formed due to the attraction between moon and earth? Tides
1532. The angle of projection of a projectile is double the angle of inclination of the plane on which a
particle is projected. The ratio of time of flights on the upward inclined plane and downward inclined
plane will be equal to
a. 1/cosa b. 1/2cosa c. 1/sina d. 1/2sina
1533. The center of gravity of circular cone lies on the axis at a height from base:
a. H/4 b. H/3 c. 3h/4 d. 3h/5
1534. The slope of constant pressure line on temperature entropy diagram is give by
a. S/T b. T/S c. Cf/T d. T/Cf
1535. The fact that the product of pressure and volume of a fixed amount of gas is of approximately
constant value is known as:
a. Charle’s law b. Gay lussac’s law c. Dalatons law d. None of the these
1536. The net work done in a polytrophic process is equal to? P1V1 – P2V2/(n-1)
1547. Air fuel ratio for a gas turbine is closer to a. 10:1 b. 15:1 c. 20:1 d. 60:1
1548. Chocking is
a. Variation of mass flow rate in proportion to pressure ration
b. Variation of mass flow rate in inverse proportion to pressure ration
c. Fixed mass flow rate regardless of pressure ration
d. None of these
1549. Kinematics of machines deals with
a. Apparatus for applying mechanical power
b. Number of inter related parts
c. The forces acting on the parts of the machine
d. The relative motion between the parts neglecting the consideration of the force.
1554. In a cam and follower mechanism, for the uniform velocity of the follower, the displacement
curve will have
a. No slope b. Constant slope.
c. Slope in positive direction only d. Slope in both positive and negative direction
1556. The number of instantaneous centers for a four bar chain mechanism would be
a. 3 b. 4 c. 5 d. 6
1560. If n1 and n2 are the max. And min. Equ. Speeds then sensitiveness of governor would be a.
N1+n2/2n1 b. N1+n2/2n2 c. N1-n2/2n1 d. N1-n2/2(n1+n2)
1561. The advantages of involute profile over cycloidal are given below. Identity if there is any incorrect
statement
a. The straight the teeth of the basic rack for the involute profile admits of simple tools
b. The profile for the flank and face is a single curve in the involute system
c. The variation in the center distance within limits does not affect the two mating gears in the involute
system d. The interference is inherently absent in this system
1563. A vibrometer
a. Indicates vibration amplitude b. Indicated vibration frequency
c. Indicates nature of vibrations d. Only indicates second and above harmonics
1565. Simply supported beam of length L with a concentrated load acting on the mid span. If the mass
of beam is negligible compared to the mass acting, the naturall frequency of the system would be?
(48EI/ml3)1/2
1568. What is the process used to get soft core and hard case? Case Carburizing
1569. By which process we get more hard and wear resistant surface?
a. Nitriding b. Chrome plating
1581. A ball tied at the end of a flexible inelastic string of length l is making S.H.M in vertical plane. At
the mean position the mass has Max K.E and min. P.E
1582. A block of steel is loaded by a tangential force on its top surface while the bottom surface is held
rigidly. The deformation of block is due to shear only
1583. Controlling force in a centrifugal type of governor is provided only by combination of dead
weight and spring
1584. The bolts in a flange coupling are designed under shearing stress caused by torque transmitted
1585. The advantage offered by multiple plate clutches as compared to single plate clutch is less radial
space requirement
1586. The cost of mechanical drives increases in this order flat belt, v-belt, chain, Gear
1588. A soap bubble has a spherical shape because a sphere will have minimum surface area for a
given volume
1589. A liquid in atm of air begins to boil when vapour pre. Of liquid slightly exceeds the air
pressure
1590. The phenomenon of surface tension of liquid causes liquid surface to contact
1592. Variations of pressure and volume at constant temperature are correlate through
1593. A gas is so expanded in a cylinder that its temperature remains constant. Several values of
pressure and volume are recorded. Volume is plotted as ordinate and inverse of pressure as abscissa. The
resulting curve will be
1594. An engine receives 15152J/s of heat and produces 5kW of power. The efficiency of the engine is
27.5
1595. An engine operating on diesel cycle is more efficient than an engine operating on otto cycle
because compression ratio is higher in diesel engine than in engine operating on otto cycle
1596. The entropy principle states that the entropy of an isolated system remains constant
1597. H7-h6 is
a. clearance fir b. transition fit c. interference fit d. sliding fit
1598. Thread can be formed by all process except
a. Forging b. rolling c. Milling d. Turning
1603. Normal hardness value of cast iron used in lathe bed. In BHN
1604. In which process material is not removed? a. punching b. coining c. tapping d. embossing
1605. Which type of transmission drive is Noiseless – (Belt drive/ Gear/ Chain)
1606. Which type of gear gives less noise? (Worm / Helical / Spur)
1615. How will you measure the Hardness of Rubber (Vickers / Brinell)
1617. Which of the following is antistatic material? (MS / Steel / Brass / Al)
1618. Carbon is added to steel-to increase? Hardness
1621. A metal has K temp gradient and 2K for another metal. If a hot fluid is passed through a pipe the
pipe should be made up of
a. K inside, 2K outside. b. 2K inside, K outside c. Any of the above d. None of the above.