Professional Documents
Culture Documents
MSDS Loctite Nordbak Wearing Compound Resin
MSDS Loctite Nordbak Wearing Compound Resin
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING: CAUSES SKIN IRRITATION.
MAY CAUSE AN ALLERGIC SKIN REACTION.
CAUSES SERIOUS EYE IRRITATION.
PICTOGRAM(S)
Precautionary Statements
Prevention: Avoid breathing vapors, mist, or spray. Wash affected area thoroughly after handling.
Contaminated work clothing should not be allowed out of the workplace. Wear protective
gloves, eye protection, and face protection.
Response: IF ON SKIN: Wash with plenty of water. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation or
rash occurs: Get medical attention. If eye irritation persists: Get medical attention. Take off
contaminated clothing.
Storage: Not prescribed
Disposal: Dispose of contents and/or container according to Federal, State/Provincial and local
governmental regulations.
Classification complies with OSHA Hazard Communication Standard (29 CFR 1910.1200) and is consistent with the provisions of the
United Nations Globally Harmonized System of Classification and Labeling of Chemicals (GHS).
* Exact percentage is a trade secret. Concentration range is provided to assist users in providing appropriate protections.
Skin contact: Immediately flush skin with plenty of water (using soap, if available). Remove
contaminated clothing and footwear. Get medical attention. Wash clothing
before reuse.
Eye contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15
minutes. Get medical attention.
Special firefighting procedures: Wear self-contained breathing apparatus and full protective clothing, such as
turn-out gear.
Unusual fire or explosion hazards: In case of fire, keep containers cool with water spray. Closed containers may
rupture (due to build up of pressure) when exposed to extreme heat.
Clean-up methods: Ensure adequate ventilation. Wear appropriate personal protective equipment.
Refer to Section 8 "Exposure Controls / Personal Protection" prior to clean up.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder,
universal binder, sawdust). Scrape up spilled material and place in a closed
container for disposal.
Storage: Keep container tightly closed and in a cool, well-ventilated place away from
incompatible materials. Store away from heat, sparks, flames, or other
sources of ignition. Protect from direct sunlight.
Engineering controls: Use local ventilation if general ventilation is insufficient to maintain vapor
concentration below established exposure limits.
Respiratory protection: Use a NIOSH approved air-purifying respirator if the potential to exceed
established exposure limits exists.
Eye/face protection: Safety goggles or safety glasses with side shields. Full face protection should
be used if the potential for splashing or spraying of product exists. Safety
showers and eye wash stations should be available.
Skin protection: Use chemical resistant, impermeable clothing including gloves and either an
apron or body suit to prevent skin contact.
Conditions to avoid: Keep away from heat, ignition sources and incompatible materials.
Inhalation: Inhalation of vapors or mists of the product may be irritating to the respiratory system.
Skin contact: Causes skin irritation. May cause allergic skin reaction.
Eye contact: Causes serious eye irritation.
Ingestion: May cause gastrointestinal tract irritation if swallowed.
Hazardous Component(s) LD50s and LC50s Immediate and Delayed Health Effects
Aluminium oxide None Irritant, Nuisance dust, Corrosive
Epoxy resin None Allergen, Irritant
Silicon carbide None Nuisance dust
Oral LD50 (Rat) = > 22,500 mg/kg
Silicon dioxide Nuisance dust
Oral LD50 (Mouse) = > 15,000 mg/kg
Blood, Central nervous system, Immune
Magnesium oxide None
system, Irritant
Treated fumed silica None Irritant
Allergen, Blood, Bone Marrow, Immune
Neopentyl glycol diglycidyl ether None
system, Irritant, Reproductive
Irritant, Respiratory, Some evidence of
Titanium dioxide None
carcinogenicity
Substituted silane None Allergen, Irritant
OSHA Carcinogen
Hazardous Component(s) NTP Carcinogen IARC Carcinogen
(Specifically Regulated)
Aluminium oxide No No No
Epoxy resin No No No
Silicon carbide No Group 2A No
Silicon dioxide No No No
Magnesium oxide No No No
Treated fumed silica No No No
Neopentyl glycol diglycidyl ether No No No
Titanium dioxide No Group 2B No
Substituted silane No No No
Recommended method of disposal: Follow all local, state, federal and provincial regulations for disposal.
TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act
Inventory.
TSCA 12 (b) Export Notification: None above reporting de minimis
California Proposition 65: This product contains a chemical known in the State of California to cause cancer. This
product contains a chemical known to the State of California to cause birth defects or other
reproductive harm.
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic
Substances List.
DISCLAIMER: The data contained herein are furnished for information only and are believed to be reliable. However, Henkel
Corporation and its affiliates (“Henkel”) does not assume responsibility for any results obtained by persons over whose methods
Henkel has no control. It is the user’s responsibility to determine the suitability of Henkel’s products or any production methods
mentioned herein for a particular purpose, and to adopt such precautions as may be advisable for the protection of property and
persons against any hazards that may be involved in the handling and use of any Henkel’s products. In light of the foregoing,
Henkel specifically disclaims all warranties, express or implied, including warranties of merchantability and fitness for a particular
purpose, arising from sale or use of Henkel’s products. Henkel further disclaims any liability for consequential or incidental damages
of any kind, including lost profits.