Gate Valves

You might also like

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

Resilient Seated Gate Valves

DN350-1200
TALIS Resilient seated gate valves DN350-1200
2

BV-05-47
RESILIENT SEATED GATE VALVE

Features
• Low head loss.
• Complete watertightness.
• Maintenance free.
• Low operating torque values.
• Straight and full bore
• Replaceable packing version
• Four independent stem seals: two o-rings above the collar and two o-rings below
• Dust seal to prevent ingress of dirt at the stem level
• Stem in stainless steel
• Bonnet bolts fully covered
• Blue RAL 5015 epoxy powder coating electrostatically applied - 250 microns.
• Equipped with by-pass from DN600
• Flange dimensions according to EN 1092-2, PN10 or PN16.
• Face to face dimensions according to EN 558, short (series 14) and long (series
15) pattern.
• Wedge fully covered with elastomer up to DN500 included, and wedge with
elastomer seating face for bigger sizes.
• Different types of operation available.

Scope
Gate vale for on/off duty for:
• Potable water, sewage, seawater,…
• Industrial processes.
• Irrigation.

Pressures and temperatures


• Maximum working pressure: PN16.
• Temperature: from –10 °C up to 50°C.

Specific manufacturing requirements


Upon request gate valves can be manufactured as follows:
• Thicker epoxy coating.
• Anticlockwise closing (CWO).
• Specific materials suitable for special applications (sewage, seawater,…)
• Other painting colors (RAL).
TALIS Resilient seated gate valves DN350-1200
3

Quality control and valve testing (according to EN 12266-1 - EN 1074)


100% of TALIS resilient seated gate valves are tested according to EN 12266-1,
DIN 3230, or as per customer requirements.

Testing pressures:
Shell tightness: 1,5 times the allowable pressure at room temperature.
Seat tightness: 1,1 times the allowable pressure at room temperature.

Minimum test duration (in seconds)


Nominal Diameter DN Shell Seat
From DN250 up to DN450 (both included) 180 30
DN500 and above 180 60

Maximum allowable seat leakage


The criteria for seat leakage of TALIS resilient seated gate valves is Rate A: no
visually detectable leakage for the duration of the test (“zero drops”).

Operating torque

The operating torque of TALIS resilient seated gate valves complies with the
Maximum Operating Torque (MOT) requirement of the standard EN 1074.

The chart shows the typical operating torque values of TALIS resilient seated
gate valves with clean water and at room temperature.

These values are only for orientation and can vary depending on the typical
manufacturing variables. For other fluids and temperature please feel free to
contact us.

Please apply 1,3 as safety factor for actuator selection.


DN Torque (Nm)
350 310
400 350
*450 350
500 450
600 500
*700 500
800 1200
*900 1200
1000 1500
*1200 1500

*Reduced bore to DN 400, 600, 800, 1000 mm.


TALIS Resilient seated gate valves DN350-1200
4

COMPONENTS
DN350-500

Item Name No. Pieces Material Standard


1 Body** 1 EN-GJS-500-7 (GGG-50) EN 1563
2 Bonnet** 1 EN-GJS-500-7 (GGG-50) EN 1563
3 Wedge 1 EN-GJS-500-7 (GGG-50) EN 1563
4 Wedge coating 1 EPDM* EN 681-1
5 Stem 1 X20 Cr13 EN 10080
6 Wedge lock nut 1 Bronze Rg. 5 EN 12165
7 Body bonnet gasket 1 EPDM* EN 681-1
8 Top bonnet** 1 EN-GJS-500-7 (GGG-50) EN 1563
9 Body bonnet bolt acc./DN 8.8 steel (GEOMET coated) DIN 912
10 Washer 2 Bronze Rg. 5 DIN 1705
11 Bonnet-top bonnet o ring 1 NBR
12 Top bonnet o ring 2 NBR
13 Guide gland 1 Teflon
14 Bonnet. o ring 2 NBR
15 Dust guard 1 EPDM
16 Top bonnet bolt 6 8.8 steel (GEOMET coated) DIN 912
17 Square cap bolt 1 X5 CrNi 18 10 EN 10088
18 Square cap*** 1 EN-GJS-500-7 (GGG-50) EN 1563
19 Cotter 1 F-114 steel UNE 3604
20 Handwheel*** 1 St 42 steel DIN 17100
21 Eyebolt 2 C 15 steel DIN 17210
22 Handwheel washer 1 X5 CrNi 18 10 EN 10088
23 Handwheel bolt 1 X5 CrNi 18 10 EN 10088
24 Draining plug 1 8.8 steel (GEOMET coated)
25 O ring draining plug 1 NBR
26 Square cap plug 1 Lupolen

* or NBR, depending on the approval and on the application.


** blue coating (Ral 5015) with epoxy powder.
*** black epoxy coating.

Optional accessories

Packing detail
TALIS Resilient seated gate valves DN350-1200
5

COMPONENTS
DN600-1200

Item Name No. Pieces Material Standard


1 Body** 1 EN GJS 500/7 EN 1563
2 Bonnet** 1 EN GJS 500/7 EN 1563
3 Wedge** 2 EN GJS 500/7 EN 1563
4 Wedge bonnet** 1 EN GJS 500/7 EN 1563
5 Stem 1 X20 Cr13 DIN 17440
6 Wedge gasket 1 EPDM* EN 681-1
7 Top bonnet** 1 C45E EN 10083
8 Wedge lock nut 1 Bronze Rg.5 DIN 1705
9 Body bonnet bolt Acc./DN 8.8 Steel
10 Body bonnet gasket 1 EPDM* EN 681-1
11 Top bonnet bolt Acc./DN 8.8 Steel
12 Spindle gland 1 POM
13 Bonnet- top bonnet o-ring 1 NBR
14 Top bonnet o-ring 2 NBR
15 Wedge bolt Acc./DN 8.8 Steel
16 O-ring wedge Acc./DN NBR
17 Gland 1 POM
18 Draining plug 1 8.8 Steel
19 Handwheel*** 1 St 42 Steel
20 Eyebolt 2 C-15 Steel
21 Cotter 1 F-1140
22 Handwheel bolt 1 18.8 Stainless steel
23 Handwheel washer 1 18.8 Stainless steel
24 Flange bolt (by-pass) Acc./DN 6.8 Steel
25 Ext. O-ring gland 1 NBR
26 Int. O-ring gland 2 NBR
27 Dust guard 1 NBR
28 TALIS RSGV 1 DN By-pass DN
29 Elbow by-pass 1 EN GJS 500/7 600 65
30 Flange- flange gasket 3 EPDM* UNE 53571 *700 65
31 Flange washer (bolt by-pass) Acc./DN 6.8 Steel 800 80
32 Flange washer (nut by-pass) Acc./DN 6.8 Steel *900 80
33 Flange nut (by-pass) Acc./DN 6.8 Steel 1000 100
34 Square cap*** 1 C45E EN 10083 *1200 100
35 Square cap bolt 1 18.8 Stainless steel
36 O-ring draining plug 1 NBR
37 Square cap plug 1 LUPOLEN

* or NBR, depending on the approval and on the application.


** blue coating (Ral 5015) with epoxy powder.
*** black epoxy coating.

Optional accessories
Packing detail
TALIS Resilient seated gate valves DN350-1200
6

DIMENSIONS

Free shaft:

DN350
27,3
M12

14

Ø6,3

47
Ø40

From DN400 to DN700

M12

C
F

Ød
E

EN 1092-2 PN 10 EN 1092-2 PN 16 EN 558 Weight kg No. of


DN D b S14 S15 A F B E D1 S14 S15 turns
K G no. x d K G no. x d (F4) (F5) (F4) (F5) for closing
350 520 26.5 460 429 16x23 470 429 16x28 290 - 750 260 478 - 500 185 - 50
400 580 28 515 482 16x28 525 480 16x31 310 600 970 290 660 - 800 275 325 57
*450 640 28 565 532 20x28 585 550 20x31 330 650 970 320 660 - 800 360 425 57
500 715 31.5 620 585 20x28 650 609 20x34 350 700 1103 357,5 828 - 800 456 530 63
600 840 36 725 682 20x31 770 720 20x37 390 800 1280 420 854 714 800 950 1100 60
*700 910 39.5 840 794 24x31 840 794 24x37 - 900 1280 455 854 714 800 - 1300 60
800 1025 43 950 901 24x34 950 901 24x40 470 - 1678 512,5 1120 829 - 2000 - 100
*900 1125 46.5 1050 1001 28x34 1050 1001 28x40 - 1100 1678 562,5 1120 829 - - 2300 100
1000 1255 50 1160 1112 28x37 1170 1112 28x43 550 - 2100 627,5 1338 976 - 3040 - 125
*1200 1485 57 1380 1328 32x40 1390 1328 32x49 - 1400 2100 742,5 1338 976 - - 3300 125

Free shaft Prepared for actuator


Top
DN A B C Ød flange T S R nxd e h X ØC J Y COTTER
ISO 5210
350 see drawing F14 175 140 100 4 x 18 4,5 70 26,2 30 8 33,2 8x7x56
400 58 64 65,3 47 F14 175 140 100 4 x 18 4,5 75 39,5 45 14 48 14x9x50
*450 58 64 65,3 47 F14 175 140 100 4 x 18 4,5 75 39,5 45 14 48 14x9x50
500 60 66 72 47 F16 210 165 130 4 x 22 5,5 75 35,2 40 12 43,2 12x8x60
600 60 66 72 50 F16 210 165 130 4 x 22 5,5 75 35,2 40 12 43,2 12x8x70
*700 60 66 72 50 F16 210 165 130 4 x 22 5,5 75 35,2 40 12 43,2 12x8x70
800 - - - - F25 300 254 200 8 x 18 5,5 75 53,1 60 18 64,1 18x11x63
*900 - - - - F25 300 254 200 8 x 18 5,5 75 53,1 60 18 64,1 18x11x63
1000 - - - - F25 300 254 200 8 x 18 5,5 135 62,4 70 20 74,4 20x12x110
*1200 - - - - F25 300 254 200 8 x 18 5,5 135 62,4 70 20 74,4 20x12x110

* Bore dimension is DN 400, 600, 800, 1000 mm. DN700, 900 and
Prepared for actuator:
1200 are produced respectively with DN600, 800 and 1000 short
Optional from DN350 to DN700,
standard for DN800 and above
pattern and convergent and divergent.
nxd

DN800 and bigger sizes are supplied with ISO top flange as
standard manufacturing. Operation must be done with gear-box or
electric actuator.
e
TALIS Resilient seated gate valves DN350-1200
7

INSTALLATION AND
OPERATING INSTRUCTIONS

Storage

Leave the rubber wedge slightly open: if it is closed completely, the rubber
suffers an unnecessary compression.

Take also into account that long storage under adverse conditions can drive to
damage in the coating, elastomer and seals.

Assembly in pipe

The assembly of the valve in the pipe is independent of the flow direction.

When connecting the valve to the pipe, avoid the transmission of the stresses
from the pipe to the valve body. For that, any pipe or pipe sections or valve not yet
finally clamped in place must be provisionally supported to prevent abnormal
stress on one or both sides of the valve.

Tighten screws gradually in a star-shaped pattern.

Once the valve is assembled, the threads of the bolts/rods should be greased
with a brush or spray. MOLYCOTE or a similar graphite based waterproof grease
should be used to prevent corrosion and facilitate subsequent dismantling
operations. TALIS gate valves can be installed in
applications such as potable water
transmission, sewage treatment
Operation
plants, ...
Each valve is operated by means of a hand-wheel or a square cap. In the latter
case a purpose-designed operating key must be used. Valves are opened anti-
clockwise unless otherwise requested.

Use

Do not use the valves for regulating mode.

Do not use the valves with gaseous fluids such as propane, butane, natural gas
and not with fluids type gasolina, gas-oil…

Recommended positions for clean water:

30º Min

1) Ideal position: vertical stem, horizontal flow 2) Horizontal flow 3) Not recommended
TALIS is the undisputed Number One for water transport and water flow
control. TALIS has the best solutions available in the fields of water and
energy management as well as for industrial and communal applications.
We have numerous products for comprehensive solutions for the whole
water cycle – from hydrants, butterfly valves and knife gate valves through
to needle valves. Our experience, innovative technology, global expertise
and individual consultation processes form the basis for developing long-
term solutions for the efficient treatment of the vitally important resource TALIS Southern Europe
“water”. BºZabalondo, 31
48100 Mungia, Bizkaia, Spain
PHONE +34 94 488 91 20
FAX +34 94 488 91 25
E-MAIL belgicast@talis-group.com
INTERNET www.talis-group.com
01-2016A

Note: Specifications may be changed without notification at any time.


Copyright: No copying without express written permission of TALIS.
TALIS is a Registered Trademark.

You might also like