Professional Documents
Culture Documents
Gate Valves
Gate Valves
Gate Valves
DN350-1200
TALIS Resilient seated gate valves DN350-1200
2
BV-05-47
RESILIENT SEATED GATE VALVE
Features
• Low head loss.
• Complete watertightness.
• Maintenance free.
• Low operating torque values.
• Straight and full bore
• Replaceable packing version
• Four independent stem seals: two o-rings above the collar and two o-rings below
• Dust seal to prevent ingress of dirt at the stem level
• Stem in stainless steel
• Bonnet bolts fully covered
• Blue RAL 5015 epoxy powder coating electrostatically applied - 250 microns.
• Equipped with by-pass from DN600
• Flange dimensions according to EN 1092-2, PN10 or PN16.
• Face to face dimensions according to EN 558, short (series 14) and long (series
15) pattern.
• Wedge fully covered with elastomer up to DN500 included, and wedge with
elastomer seating face for bigger sizes.
• Different types of operation available.
Scope
Gate vale for on/off duty for:
• Potable water, sewage, seawater,…
• Industrial processes.
• Irrigation.
Testing pressures:
Shell tightness: 1,5 times the allowable pressure at room temperature.
Seat tightness: 1,1 times the allowable pressure at room temperature.
Operating torque
The operating torque of TALIS resilient seated gate valves complies with the
Maximum Operating Torque (MOT) requirement of the standard EN 1074.
The chart shows the typical operating torque values of TALIS resilient seated
gate valves with clean water and at room temperature.
These values are only for orientation and can vary depending on the typical
manufacturing variables. For other fluids and temperature please feel free to
contact us.
COMPONENTS
DN350-500
Optional accessories
Packing detail
TALIS Resilient seated gate valves DN350-1200
5
COMPONENTS
DN600-1200
Optional accessories
Packing detail
TALIS Resilient seated gate valves DN350-1200
6
DIMENSIONS
Free shaft:
DN350
27,3
M12
14
Ø6,3
47
Ø40
M12
C
F
Ød
E
* Bore dimension is DN 400, 600, 800, 1000 mm. DN700, 900 and
Prepared for actuator:
1200 are produced respectively with DN600, 800 and 1000 short
Optional from DN350 to DN700,
standard for DN800 and above
pattern and convergent and divergent.
nxd
DN800 and bigger sizes are supplied with ISO top flange as
standard manufacturing. Operation must be done with gear-box or
electric actuator.
e
TALIS Resilient seated gate valves DN350-1200
7
INSTALLATION AND
OPERATING INSTRUCTIONS
Storage
Leave the rubber wedge slightly open: if it is closed completely, the rubber
suffers an unnecessary compression.
Take also into account that long storage under adverse conditions can drive to
damage in the coating, elastomer and seals.
Assembly in pipe
The assembly of the valve in the pipe is independent of the flow direction.
When connecting the valve to the pipe, avoid the transmission of the stresses
from the pipe to the valve body. For that, any pipe or pipe sections or valve not yet
finally clamped in place must be provisionally supported to prevent abnormal
stress on one or both sides of the valve.
Once the valve is assembled, the threads of the bolts/rods should be greased
with a brush or spray. MOLYCOTE or a similar graphite based waterproof grease
should be used to prevent corrosion and facilitate subsequent dismantling
operations. TALIS gate valves can be installed in
applications such as potable water
transmission, sewage treatment
Operation
plants, ...
Each valve is operated by means of a hand-wheel or a square cap. In the latter
case a purpose-designed operating key must be used. Valves are opened anti-
clockwise unless otherwise requested.
Use
Do not use the valves with gaseous fluids such as propane, butane, natural gas
and not with fluids type gasolina, gas-oil…
30º Min
1) Ideal position: vertical stem, horizontal flow 2) Horizontal flow 3) Not recommended
TALIS is the undisputed Number One for water transport and water flow
control. TALIS has the best solutions available in the fields of water and
energy management as well as for industrial and communal applications.
We have numerous products for comprehensive solutions for the whole
water cycle – from hydrants, butterfly valves and knife gate valves through
to needle valves. Our experience, innovative technology, global expertise
and individual consultation processes form the basis for developing long-
term solutions for the efficient treatment of the vitally important resource TALIS Southern Europe
“water”. BºZabalondo, 31
48100 Mungia, Bizkaia, Spain
PHONE +34 94 488 91 20
FAX +34 94 488 91 25
E-MAIL belgicast@talis-group.com
INTERNET www.talis-group.com
01-2016A