Professional Documents
Culture Documents
EASA Lights
EASA Lights
EASA Lights
LIGHTS
(a) Each landing light must be approved, and must be installed so that –
(1) No objectionable glare is visible to the pilot;
(2) The pilot is not adversely affected by halation; and
(3) It provides enough light for night landing.
(b) Except when one switch is used for the lights of a multiple light installation at one location,
there must be a separate switch for each light.
(c) There must be a means to indicate to the pilots when the landing lights are extended.
(a) General. Each part of each position light system must meet the applicable requirements of this
paragraph and each system as a whole must meet the requirements of CS 25.1387 to 25.1397.
(b) Forward position lights. Forward position lights must consist of a red and a green light spaced
laterally as far apart as practicable and installed forward on the aeroplane so that, with the
aeroplane in the normal flying position, the red light is on the left side, and the green light is on
the right side. Each light must be approved.
(c) Rear position light. The rear position light must be a white light mounted as far aft as practicable
(Amendment 6)
(d) Light covers and colour filters. Each light cover or colour filter must be at least flame resistant
and may not change colour or shape or lose any appreciable light transmission during normal
use.
Easy Access Rules for Large Aeroplanes SUBPART F – EQUIPMENT
(CS-25) (Amendment 21)
LIGHTS
(a) Except as provided in sub-paragraph (e) of this paragraph, each forward and rear position light
must, as installed, show unbroken light within the dihedral angles described in this paragraph.
(b) Dihedral angle L (left) is formed by two intersecting vertical planes, the first parallel to the
longitudinal axis of the aeroplane, and the other at 110° to the left of the first, as viewed when
looking forward along the longitudinal axis.
(c) Dihedral angle R (right) is formed by two intersecting vertical planes, the first parallel to the
longitudinal axis of the aeroplane, and the other at 110° to the right of the first, as viewed when
looking forward along the longitudinal axis.
(d) Dihedral angle A (aft) is formed by two intersecting vertical planes making angles of 70 o to the
right and to the left, respectively, to a vertical plane passing through the longitudinal axis, as
viewed when looking aft along the longitudinal axis.
(e) If the rear position light when mounted as far aft as practicable in accordance with
CS 25.1385(c), cannot show unbroken light within dihedral angle A (as defined in sub-paragraph
(d) of this paragraph), a solid angle or angles of obstructed visibility totalling not more than 0·04
steradians is allowable within that dihedral angle, if such solid angle is within a cone whose apex
is at the rear position light and whose elements make an angle of 30 o with a vertical line passing
through the rear position light.
(a) General. The intensities prescribed in this paragraph must be provided by new equipment with
light covers and colour filters in place. Intensities must be determined with the light source
operating at a steady value equal to the average luminous output of the source at the normal
operating voltage of the aeroplane. The light distribution and intensity of each position light
must meet the requirements of sub-paragraph (b) of this paragraph.
(b) Forward and rear position lights. The light distribution and intensities of forward and rear
position lights must be expressed in terms of minimum intensities in the horizontal plane,
minimum intensities in any vertical plane, and maximum intensities in overlapping beams,
within dihedral angles L, R and A, and must meet the following requirements:
(1) Intensities in the horizontal plane. Each intensity in the horizontal plane (the plane
containing the longitudinal axis of the aeroplane and perpendicular to the plane of
symmetry of the aeroplane) must equal or exceed the values in CS 25.1391.
(2) Intensities in any vertical plane. Each intensity in any vertical plane (the plane
perpendicular to the horizontal plane) must equal or exceed the appropriate value in
CS 25.1393, where I is the minimum intensity prescribed in CS 25.1391 for the
corresponding angles in the horizontal plane.
(3) Intensities in overlaps between adjacent signals. No intensity in any overlap between
adjacent signals may exceed the values given in CS 25.1395, except that higher intensities
in overlaps may be used with main beam intensities substantially greater than the minima
specified in CS 25.1391 and 25.1393 if the overlap intensities in relation to the main beam
intensities do not adversely affect signal clarity. When the peak intensity of the forward
position lights is more than 102 cd (100 candles), the maximum overlap intensities
between them may exceed the values given in CS 25.1395 if the overlap intensity in Area
Easy Access Rules for Large Aeroplanes SUBPART F – EQUIPMENT
(CS-25) (Amendment 21)
LIGHTS
A is not more than 10% of peak position light intensity and the overlap intensity in Area B is
not greater than 2·5% of peak position light intensity.
Each position light intensity must equal or exceed the applicable values in the following table:
Dihedral angle Angle from right or left of longitudinal Intensity candela (candles)
(light included) axis, measured from dead ahead
L and R 0o to 10 o 41 (40)
(forward red and green) 10 o to 20 o 31 (30)
20 o to 110 o 5
A (rear white) 110 o to 180 o 20
Each position light intensity must equal or exceed the applicable values in the following table:
Angle above or below the horizontal plane: Intensity
0° 1·00 I
0° to 5° 0·90 I
5° to 10° 0·80 I
10° to 15° 0·70 I
15° to 20° 0·50 I
20° to 30° 0·30 I
30° to 40° 0·10 I
40° to 90° 0·05 I
No position light intensity may exceed the applicable values in the following table, except as provided in CS
25.1389(b)(3):
Maximum intensity
Overlaps
Area A candela (candles) Area B candela (candles)
Green in dihedral angle L 10 1
Red in dihedral angle R 10 1
Green in dihedral angle A 5 1
Red in dihedral angle A 5 1
Rear white in dihedral angle L 5 1
Rear white in dihedral angle R 5 1
Easy Access Rules for Large Aeroplanes SUBPART F – EQUIPMENT
(CS-25) (Amendment 21)
LIGHTS
Where –
(a) Area A includes all directions in the adjacent dihedral angle that pass through the light source
and intersect the common boundary plane at more than 10° but less than 20°; and
(b) Area B includes all directions in the adjacent dihedral angle that pass through the light source
and intersect the common boundary plane at more than 20°.
Each position light colour must have the applicable International Commission on Illumination chromaticity
co-ordinates as follows:
(a) Aviation red –
‘y’ is not greater than 0·335; and ‘z’ is
not greater than 0·002.
(b) Aviation green –
‘x’ is not greater than 0·440–0·320y; ‘x’ is
not greater than y–0·170; and ‘y’ is
not less than 0·390–0·170x.
(c) Aviation white –
‘x’ is not less than 0·300 and not greater than 0·540;
‘y’ is not less than ‘x–0·040’ or ‘yo–0·010’, whichever is the smaller; and
‘y’ is not greater than ‘x+0·020’ nor ‘0·636–0·400x’; Where ‘yo’ is the ‘y’ co-ordinate of the Planckian
radiator for the value of ‘x’ considered.
(a) General. The aeroplane must have an anticollision light system that –
(1) Consists of one or more approved anti-collision lights located so that their light will not
impair the crew’s vision or detract from the conspicuity of the position lights; and
(2) Meets the requirements of sub-paragraphs (b) to (f) of this paragraph.
(b) Field of coverage. The system must consist of enough light to illuminate the vital areas around
the aeroplane considering the physical configuration and flight characteristics of the aeroplane.
The field of coverage must extend in each direction within at least 75° above and 75° below the
horizontal plane of the aeroplane, except that a solid angle or angles of obstructed visibility
totalling not more than 0·03 steradians is allowable within a solid angle equal to 0·15 steradians
centred about the longitudinal axis in the rearward direction.
(c) Flashing characteristics. The arrangement of the system, that is, the number of light sources,
beam width, speed of rotation, and other characteristics, must give an effective flash frequency
of not less than 40, nor more than 100 cycles per minute. The effective flash frequency is the
frequency at which the aeroplane’s complete anti-collision light system is observed from a
distance, and applies to each section of light including any overlaps that exist when the system
Easy Access Rules for Large Aeroplanes SUBPART F – EQUIPMENT
(CS-25) (Amendment 21)
LIGHTS
consists of more than one light source. In overlaps, flash frequencies may exceed 100, but not 180
cycles per minute.
(d) Colour. Each anti-collision light must be either aviation red or aviation white and must meet the
applicable requirements of CS 25.1397.
(e) Light intensity. The minimum light intensities in all vertical planes, measured with the red filter
(if used) and expressed in terms of ‘effective’ intensities, must meet the requirements of sub-
paragraph (f) of this paragraph. The following relation must be assumed:
where:
Ie = effective intensity (candela (candles)
I(t) = instantaneous intensity as a function of time t2–t1
=flash time interval (seconds)
Normally, the maximum value of effective intensity is obtained when t2 and t1 are chosen so that the
effective intensity is equal to the instantaneous intensity at t2 and t1.
(f) Minimum effective intensities for anticollision lights. Each anti-collision light effective intensity
must equal or exceed the applicable values in the following table:
Angle above or below the horizontal plane: Effective intensity (candela (candles))
0° to 5° 407 (400)
5° to 10° 244 (240)
10° to 20° 81 (80)
20° to 30° 41 (40)
30° to 75° 20
Unless operations at night in known or forecast icing conditions are prohibited by an operating limitation, a
means must be provided for illuminating or otherwise determining the formation of ice on the parts of
the wings that are critical from the standpoint of ice accumulation. Any illumination that is used must
be of a type that will not cause glare or reflection that would handicap crewmembers in the
performance of their duties.
[Amdt 25/16]
Unless operations at night in icing conditions are prohibited by an operating limitation, CS 25.1403 requires
that a means be provided, during flight at night, to illuminate or otherwise determine ice formation on
parts of the wings that are critical from the standpoint of ice accumulations resulting from Appendix C
and Appendix O icing conditions. For showing compliance with the CS-25 certification specifications
relative to SLD icing conditions represented by Appendix O, the applicant may use a comparative
analysis. AMC 25.1420(f) provides guidance for comparative analysis.
Subpart F — Equipment
ELECTRICAL SYSTEMS AND EQUIPMENT
a. If the flight crew cannot see the wings, one acceptable means of compliance with this
regulation would be to install an ice evidence probe in a position where the flight crew can
observe ice accumulation. The applicant should substantiate that formation of ice on this
device precedes formation of ice on the wings or occurs simultaneously with it.
Consideration should be given to the need for illuminating the ice evidence probe.
b. Wing icing detection lights should be evaluated both in and out of clouds during night flight to
determine that the component of interest is adequately illuminated without excessive glare,
reflections, or other distractions to the flight crew. These tests may be accomplished during
the aeroplane certification flight tests. Typically, aeroplane-mounted illumination has been
used to comply with this regulation. Use of a hand-held flashlight has not been considered
acceptable because of the associated workload. The appropriate manual should identify the
ice characteristics which the flight crew is expected to observe as well as the action the
flight crew must perform if such ice is observed.
[Amdt
25/16]
[Amdt
25/18]