Professional Documents
Culture Documents
Yacht - Pro Catalogue - 2022-2023 - EN - UK
Yacht - Pro Catalogue - 2022-2023 - EN - UK
X-Yachts A/S
Primers & Fillers
Content
Antifoulings
Primers & Fillers 5
Below the waterline 6
Above the waterline 10
Above and below the waterline 13
Antifoulings 17
Fouling Control
Systems
Self-polishing 18
Hard 24
Topcoats
Topcoats 41
Speciality products 47
Speciality products
Health & Safety 55
4
Primers & Fillers
Yacht Pro / Primers / Below the waterline Yacht Pro / Primers / Below the waterline
45580 49200
Antifoulings
Two-component primer for gelcoats Anticorrosive two-component
antifouling tiecoat
Fouling Control
High build epoxy primer for High performance anticorrosive
Systems
Finish Flat Finish Flat
use as a bond between glass epoxy tiecoat for below the
fibre reinforced polyester and Volume Solids (% - ±2 ) 45 waterline. Volume Solids (% - ±2 ) 57
antifouling. Also for prevention Theoretical Spreading Rate 4.5 m²/L – 225 μm WFT Theoretical Spreading Rate 5.7 m²/L – 175 μm WFT
of osmotic blistering in glass 10°C - 6 hours; Minimum Overcoating Time
fibre reinforced polyester. Minimum Overcoating Time Recommended use N/A
20°C - 3 hours; (self)
(self)
30°C - 2.5 hours 10°C - 10 hours;
For immersion service used Minimum Overcoating Time
10°C - When tacky; 20°C - 5 hours;
Recommended use Minimum Overcoating Time as a tiecoat between epoxy and (Antifouling)
20°C - When tacky (30-60mins); 30°C - 4 hours
(Antifouling)
30°C - When tacky one-component coatings. Mixed VOC (g/L) 395
Topcoats
Suitable on glass fibre hulls Mixed VOC (g/L) 475
below the waterline. Especially It can also replace one
designed for professional anticorrosive primer coat for the
applications where short underwater coating system and Shades and Can sizes
Shades and Can sizes
recoating intervals are at the same time act as tiecoat
needed. for antifouling or it may also be
25150
used as a sealer over
12170 11480
old antifoulings.
Speciality products
Yellowish Grey
Stone Grey Mid Grey 2.5 | 5 | 20L
5 | 20L 5 | 20L
Application details
Application details
Base 49209 + Curing agent 98191
Base 45589 + Curing agent 98580 • Excellent adhesion Mixing ratio
• Excellent adhesion Mixing ratio 7 : 1 by volume
to gelcoat 4 : 1 by volume to epoxy primers
Thinner Hempel's Thinner 08450
Health
Thinners
Cleaners
& Safety
&
6 7
Primers & Fillers
Yacht Pro / Primers / Below the waterline Yacht Pro / Primers / Below the waterline
Hempadur Material
Steel Hempel’s Materials
Glass fibre / Wood / Steel
Antifoulings
Two-component epoxy hold primer 26031
One-component underwater primer
Description Product overview Description Product overview
Fouling Control
Suitable for use as a holding Fast-drying underwater primer
Systems
Finish Flat Finish Flat
primer below the waterline containing aluminium flakes.
with extended overcoating Volume Solids (% - ±2 ) 54 For use as a sealer onto old Volume Solids (% - ±2 ) 39
intervals. Available in various Theoretical Spreading Rate 5.4 m²/L – 200 μm WFT antifouling or as a tiecoat Theoretical Spreading Rate 7.8 m²/L – 125 μm WFT
shades including reddish grey 10°C - 16 hours; over an epoxy primed surface 10°C - 4.5 hours;
(12430) shade that contains Minimum Overcoating Time before antifouling. Minimum Overcoating Time
20°C - 8 hours; 20°C - 2.5 hours;
(self) (self)
Micaceous Iron Oxide. 30°C - 6 hours 30°C - 2 hours
10°C - 20 hours; 10°C - 4.5 hours;
Minimum Overcoating Time Recommended use Minimum Overcoating Time
20°C - 6 hours; 20°C - 2.5 hours;
(other) (other)
Recommended use 30°C - 5 hours 30°C - 2 hours
Topcoats
Mixed VOC (g/L) 415 Suitable on glass fibre, wood Mixed VOC (g/L) 476
As a holding (blast) primer in and steel. For use on all areas
new building or maintenance below the waterline including
scenarios where long keels.
overcoating intervals with Shades and Can sizes Shades and Can sizes
other epoxy systems may
be required. MIO shade
12430 50630 11320 19000
is particularly suited
Speciality products
for application in humid
conditions or on damp steel.
Reddish Grey Red Grey Aluminium Grey
20L 20L 20L 2.5 | 5 | 20L
• Extended maximum Base 15579 + Curing agent 95570 • Excellent adhesion Mixing ratio N/A
overcoating interval Mixing ratio
3 : 1 by volume • Can be used to seal
Health
Thinners
Cleaners
& Safety
&
8 9
Primers & Fillers
Yacht Pro / Primers / Above the waterline Yacht Pro / Primers / Above the waterline
Hempadur Materials
Stainless Steel / Aluminium Hempadur Mastic Materials
Steel / Aluminium
15553 45880
Antifoulings
Two-component epoxy Two-component epoxy build primer
stainless steel primer
Fouling Control
Flexible impact-resistant High solids, high build
Systems
Finish Flat Finish Semi-Gloss
primer for stainless steel and primer for use under the
aluminium. Volume Solids (% - ±2 ) 55 polyurethane topcoats. Volume Solids (% - ±2 ) 80
Theoretical Spreading Rate 11 m²/L – 100 μm WFT Theoretical Spreading Rate 6.4 m²/L – 150 μm WFT
Recommended use 10°C - 12 hours; Minimum Overcoating Time
Minimum Overcoating Time Recommended use N/A
20°C - 6 hours; (self)
(self)
30°C - 4.5 hours 10°C - 30 hours;
As a primer where surface Minimum Overcoating Time
10°C - 12 hours; Above water as a low VOC, 20°C - 10 hours;
roughening is not achievable. Minimum Overcoating Time (other)
20°C - 6 hours; high film build primer with 30°C - 7.5 hours
For use only above the (other)
30°C - 4.5 hours extended re-coating times
water on stainless steel and Mixed VOC (g/L) 216
Topcoats
Mixed VOC (g/L) 388 for heavy duty polyurethane
aluminium parts.
topcoats.
Shades and Can sizes
Shades and Can sizes
Speciality products
White Stone Grey Red
Grey 20L 20L 20L
20L
Application details
Application details
Base 45889 + Curing Agent 95880
Mixing ratio
• Suitable for stainless Base 15557 + Curing agent 98021 3 : 1 by volume
Mixing ratio
steel & anodized 3 : 1 by volume • Suitable above Thinner Hempel's Thinner 08450
aluminium the waterline
Health
Thinners
Cleaners
& Safety
&
10 11
Primers & Fillers
Yacht Pro / Primers / Above the waterline Yacht Pro / Primers / Above and below the waterline
13140 17880
Antifoulings
One-component direct-to-metal primer Two-component universal
epoxy primer
Fouling Control
Fast-drying primer with rust- Highly versatile universal
Systems
Finish Flat Finish Semi-Flat
inhibiting pigments that can primer for use above and
be applied direct to roughened Volume Solids (% - ±2 ) 42 below the waterline. Excellent Volume Solids (% - ±2 ) 72
steel. Theoretical Spreading Rate 8.4 m²/L – 125 μm WFT barrier coating and resistant Theoretical Spreading Rate 5.76 m²/L – 160 μm WFT
10°C - 12 hours; to abrasion. 10°C - 6 hours;
Minimum Overcoating Time Minimum Overcoating Time
20°C - 6 hours; 20°C - 3 hours;
(self) (self)
Recommended use 30°C - 4.5 hours 30°C - 2.5 hours
10°C - 4 hours; Recommended use 10°C - 6 hours;
Above the waterline as a Minimum Overcoating Time Minimum Overcoating Time
20°C - 2 hours; 20°C - 3 hours;
(other) (other)
versatile primer on steel 30°C - 1.5 hours Is intended as a direct-to- 30°C - 2.5 hours
Topcoats
and other metal surfaces in Mixed VOC (g/L) 518 substrate primer for keel-to-rail Mixed VOC (g/L) 276
a mild to medium corrosive use on all size yachts made of
environment. Ideal undercoat GRP, FRP, steel, or aluminium.
for Hempalin and Hempatex The product is suitable to be
Shades and Can sizes Shades and Can sizes
topcoats. overcoated with tiecoats, fillers
or other coatings as specified.
11320 50630 22090 57530
Speciality products
Grey Red Light Aluminium
5 | 20L 5 | 20L Beige Red
5 | 20L 5 | 20L
Application details
Application details
• Excellent
• Suitable above Mixing ratio N/A anticorrosive
the waterline Base 17889 + Curing agent 95870
• Very good mechanical Mixing ratio
• Reduces need for Thinner Hempel's Thinner 08080 4 : 1 by volume
Health
Thinners
Cleaners
& Safety
&
12 13
Primers & Fillers
Yacht Pro / Primers / Above and below the waterline Yacht Pro / Fillers / Above the waterline
45550 Plywood
35370
Antifoulings
Two-component multi-purpose Two-component epoxy fairing filler
epoxy primer
Fouling Control
High performance epoxy primer Lightweight smooth epoxy
Systems
Finish Flat Finish Semi-Gloss
and undercoat for use both filler with strong adhesion and
above and below the waterline. Volume Solids (% - ±2 ) 52 water resistance. Easy to sand Volume Solids (% - ±2 ) 100
Superb corrosion, impact and Theoretical Spreading Rate 5.2 m²/L – 200 μm WFT when fully cured. Theoretical Spreading Rate N/A
water resistance. 10°C - 16 hours; 10°C - 48 hours;
Minimum Overcoating Time Minimum Overcoating Time
20°C - 8 hours; Recommended use 20°C - 24 hours;
(self) (self @ 1mm)
30°C - 6 hours 30°C - 12 hours
Recommended use
10°C - 4 hours; As a filler and fairing compound 10°C - 48 hours;
Minimum Overcoating Time Minimum Overcoating Time
As a primer below and above 20°C - 2 hours; above and below the waterline. 20°C - 24 hours;
(other - tiecoat) (other @ 1mm)
30°C - 1 hour 30°C - 12 hours
the waterline on boats made of Especially suitable for profiling
Topcoats
aluminium, glass fibre reinforced Mixed VOC (g/L) 433 large areas and detailed fairing Mixed VOC (g/L) 2
polyester, wood, plywood and where structural strength is Density (Kg/L) 0.7
steel. Also for prevention and important. It can be used on
repair of osmotic blistering in the Shades and Can sizes most primed rigid substrates
glass fibre reinforced polyester, and can be applied up to 10-
Shades and Can sizes
and for protection of keels and 12mm for a uniform smooth
rudders. 11630 12170 film build.
Speciality products
49500
Off White Stone Grey
5 | 20L 5 | 20L
Light Green
5 | 20 | 380L
Application details
Application details
• Excellent adhesion Base 45559 + Curing agent 95360 • Low density /
Mixing ratio
to all yacht substrates 2 : 1 by volume lightweight Base 35379 + Curing agent 95720
Mixing ratio
Health
Thinners
Cleaners
& Safety
&
14 15
Fouling Control Thinners &
Antifoulings Topcoats Speciality products Thinners & Cleaners Health
Health&&Safety
Safety
Systems Cleaners
17
Antifoulings
• Self-polishing
• Hard
16
Yacht Pro / Antifoulings / Self-polishing Yacht Pro / Antifoulings / Self-polishing
71880 7188W
Antifoulings
Self-polishing antifouling Self-polishing antifouling
Fouling Control
High performance, self- High performance, self-
Systems
Finish Flat Finish Flat
polishing antifouling. Hempel's polishing antifouling. Hempel's
patented binder technology Volume Solids (% - ±2 ) 50 patented binder technology Volume Solids (% - ±2 ) 53
ensures outstanding Theoretical Spreading Rate 10 m²/L – 100 μm WFT ensures outstanding fouling Theoretical Spreading Rate 10.6 m²/L – 100 μm WFT
fouling protection and 10°C - 8 hours; protection and colour retention 10°C - 8 hours;
colour retention all season. Minimum Overcoating Time all season. Minimum Overcoating Time
20°C - 4 hours; 20°C - 4 hours;
(self @ 1mm) (self @ 1mm)
Hempel's Mille NCT 71880 is 30°C - 2 hours 30°C - 2 hours
compatible with virtually all 10°C - 36 hours; 10°C - 36 hours;
Recommended use
other antifouling systems. Minimum Time To Immersion 20°C - 24 hours; Minimum Time To Immersion 20°C - 24 hours;
30°C - 24 hours 30°C - 24 hours
As an antifouling for boats of
Topcoats
Recommended use Mixed VOC (g/L) 423 glass fibre, wood, plywood, Mixed VOC (g/L) 406
steel and aluminium.
Suitable for boats made of
glass fibre, wood, plywood and Shades and Can sizes Shades and Can sizes
steel. Do not use on aluminium
or other light-alloy metals. Risk
of corrosion in case of direct 19990 37110 56460 10000
contact.
Speciality products
Black Dark Blue Insignia Red White
5L 5L 5L 5L
• Superior • Superior
Mixing ratio N/A Mixing ratio N/A
mechanical strength mechanical strength
Thinner Hempel's Thinner 08080 • Premium crack resistance Thinner Hempel's Thinner 08080
• Premium crack
Health
Health
Thinners
Cleaners
&&Safety
Safety
&
18 19
Yacht Pro / Antifoulings / Self-polishing Yacht Pro / Antifoulings / Self-polishing
Antifoulings
Self-polishing antifouling 74830
Self-polishing antifouling
Description Product overview Description Product overview
Fouling Control
Efficient polishing (erodible) High performance, self-
Systems
Finish Flat Finish Flat
antifouling providing good polishing antifouling. Hempel's
protection all season. Volume Solids (% - ±2 ) 50 patented binder technology Volume Solids (% - ±2 ) 53
Theoretical Spreading Rate 10 m²/L – 100 μm WFT ensures outstanding fouling Theoretical Spreading Rate 10.6 m²/L – 100 μm WFT
10°C - 8 hours; protection and colour retention 10°C - 8 hours;
Recommended use Minimum Overcoating Time Minimum Overcoating Time
20°C - 4 hours; all season. 20°C - 4 hours;
(self @ 1mm) (self @ 1mm)
30°C - 2 hours 30°C - 2 hours
As an antifouling for boats of
glass fibre, wood, plywood and 10°C - 36 hours; Recommended use 10°C - 36 hours;
steel. Do not use on aluminium Minimum Time To Immersion 20°C - 24 hours; Minimum Time To Immersion 20°C - 24 hours;
30°C - 24 hours 30°C - 24 hours
or other light-alloy metals. Risk As an antifouling for boats of
Topcoats
of corrosion in case of direct Mixed VOC (g/L) 424 glass fibre, wood, plywood, Mixed VOC (g/L) 406
contact. steel and aluminium. For all
below waterline areas including
Shades and Can sizes stern gear & propellers. Shades and Can sizes
Speciality products
Black True Blue Red Brown Souvenirs Blue Ultimate White Black True Blue
5L 5L 5L 5L 5L 5L 5L
• Good mechanical Mixing ratio N/A • Especially suited Mixing ratio N/A
strength for aluminium boats
• Improved crack Thinner Hempel's Thinner 08080 • Bright, clean colours Thinner Hempel's Thinner 08080
Health
Health
Thinners
Cleaners
&&Safety
Safety
&
20 21
Yacht Pro / Antifoulings / Self-polishing Yacht Pro / Antifoulings / Self-polishing
Hempel’s Materials
Glass fibre / Wood / Plywood /
Steel
Hempel's Materials
Glass fibre / Wood / Plywood /
Steel / Aluminium
Antifoulings
71000 7103A
Self-polishing antifouling Self-polishing antifouling
Description Product overview Description Product overview
Fouling Control
High performance, conventional, High performance, self-polishing
Systems
Finish Flat Finish Flat
erodible antifouling providing antifouling providing excellent
excellent protection all season. Volume Solids (% - ±2 ) 51 protection all season. Volume Solids (% - ±2 ) 35
Theoretical Spreading Rate 10.2 m²/L – 100 μm WFT Theoretical Spreading Rate 7 m²/L – 100 μm WFT
10°C - 8 hours; Recommended use 10°C - 8 hours;
Recommended use Minimum Overcoating Time Minimum Overcoating Time
20°C - 4 hours; 20°C - 4 hours;
(self @ 1mm) (self @ 1mm)
30°C - 2 hours As an antifouling for glass 30°C - 2 hours
As an antifouling for glass fibre,
10°C - 36 hours; fibre, wood, plywood, steel and 10°C - 36 hours;
wood, plywood and steel. Do not
Minimum Time To Immersion 20°C - 24 hours; aluminium. For power and sailing Minimum Time To Immersion 20°C - 24 hours;
use on aluminium or other light
30°C - 24 hours boats. 30°C - 24 hours
alloy metals. Risk of corrosion in
Topcoats
case of contact. For power and Mixed VOC (g/L) 422 Mixed VOC (g/L) 405
sailing boats.
Speciality products
True Blue Black Insignia Red Grey Souvenirs Blue Dark Blue Ultimate White
5L 5L 5L 5L 5L 5L 5 | 20L
Health
Health
Thinners
Cleaners
&&Safety
Safety
&
22 23
Yacht Pro / Antifoulings / Hard Yacht Pro / Antifoulings / Hard
Hempel’s Materials
Glass fibre / Wood / Plywood /
Steel
Hempel’s Materials
Glass fibre / Wood / Plywood /
Aluminium / Steel
Antifoulings
76880 76300
Hard matrix antifouling Hard matrix antifouling
Description Product overview Description Product overview
Fouling Control
High performance, hard High performance, hard
Systems
Finish Flat Finish Flat
antifouling providing antifouling providing excellent
outstanding protection all Volume Solids (% - ±2 ) 49 protection all season. Volume Solids (% - ±2 ) 54
season. Includes TecCel Theoretical Spreading Rate 9.8 m²/L – 100 μm WFT Theoretical Spreading Rate 10.8 m²/L – 100 μm WFT
technology which ensures 10°C - 8 hours; 10°C - 8 hours;
Minimum Overcoating Time Recommended use Minimum Overcoating Time
reduced friction and increased 20°C - 4 hours; 20°C - 4 hours;
(self @ 1mm) (self @ 1mm)
speed. It changes to its final 30°C - 2 hours 30°C - 2 hours
As an antifouling for boats of
colour after approximately 1 10°C - 36 hours; 10°C - 36 hours;
glass fibre, wood, plywood,
week of immersion in water. Minimum Time To Immersion 20°C - 24 hours; Minimum Time To Immersion 20°C - 24 hours;
steel and aluminium. For
30°C - 24 hours 30°C - 24 hours
powerboats and regatta
Topcoats
Recommended use Mixed VOC (g/L) 437 yachts. Mixed VOC (g/L) 394
Speciality products
regatta yachts. Pepper Grey Black True Blue Dark Blue Insignia Red Ultimate White
5L 5L 5L 5L 5L 5L
Health
Health
Thinners
Cleaners
&&Safety
Safety
&
24 25
Fouling Control Thinners &
Topcoats Speciality products Thinners & Cleaners Health & Safety
Systems Cleaners
27
Fouling Control
Systems
• Fouling Defence
• Fouling Release
26
Yacht Pro / Fouling Control Systems Yacht Pro / Fouling Control Systems
Biocide-free
Fouling defence
Instant effect on water contact
Fouling Control
Our unique Actiguard technology gives
Systems
you the best of two worlds: silicone-
hydrogel and diffusion control of
biocides, all in a single fouling defence
High activity level
coat. You can expect 6 per cent fuel
savings compared to best-in-class
antifoulings over the entire service
interval, regardless of trading patterns Low activity level
and sailing speed, and a clean hull
over an idle period of up to 120 days.
The result is exceptional fouling control
Topcoats
performance and lower CO2 emissions Up to 120 days idle time
over docking intervals of up to
60 months.
Possible to switch from tropical to colder waters
Fouling release
Speciality products
Easy overcoating
Our fouling release technology is
based on biocide-free silicone and
hydrogel, giving you a smooth hull Application in warm environment
surface that makes it difficult for
fouling organisms to attach. The
result is less drag, fuel savings
averaging 5 per cent and lower CO2 Full return on paint investment
emissions, increasing the efficiency
Hempel’s
Fouling Defence & Release systems Hempel’s Silic One 77450
New boat without epoxy
Hempaguard® X7
SilicOne
Silic One/ 80 micron DFT
Full system for new and bare hull ‒ 5 year scheme
SilicOne
Silic One/ 80 micron DFT
Hempaguard X7 / 100 micron DFT
Hempaguard X7 / 100 micron DFT SilicOne
Silic One Tiecoat
Tiecoat / 67 micron DFT
Fouling Control
5x Primer / 300 micron DFT
Hempel's Premium Primer 17880 / 125 micron DFT
Systems
Hempel's Premium Primer 17880 / 125 micron DFT
Substrate
Topcoats
New boat or bare boat with epoxy
Hempaguard X7 / 150 micron DFT
Nexus II 27400 / 100 microns DFT
Existing antifouling
Silic One
Silic One / 80 micron DFT
Silic One
Silic One / 80 micron DFT
Silic One
Silic One Tiecoat
Tiecoat / 67 micron DFT
Speciality products
Light Primer
Light Primer / 60 micron DFT
Hempasil X3+
Full system for new and bare hull ‒ 3 year scheme
Hempasil X3+ / 100 micron DFT
Hempasil X3+ / 100 micron DFT
Hempasil Nexus II / 100 micron DFT
Hempel's Premium Primer 17880 / 125 micron DFT
SilicOne
Silic One/ 80 micron DFT
SilicOne
Silic One/ 80 micron DFT
30 31
Yacht Pro / Fouling Control Systems / Fouling Defence Yacht Pro / Fouling Control Systems / Fouling Release
Hempaguard X7 Materials
Steel / Aluminium / GRP /
Stainless Steel
Hempasil X3+ Materials
Steel / Aluminium / GRP /
Stainless Steel
89900 87500
Two-component fouling defence coating Two-component fouling release coating
Fouling Control
Advanced fouling defence coating, Biocide-free, high solids finish,
Systems
Finish Glossy Finish Glossy
with high solids content, based on based on silicone hydrogel.
ActiGuard® technology. ActiGuard® Volume Solids (% - ±2 ) 70 Volume Solids (% - ±2 ) 71
Provides a smooth, low energy
combines the effect of advanced Theoretical Spreading Rate 7.0 m²/L – 140 μm WFT Theoretical Spreading Rate 7.1 m²/L – 140 μm WFT
repellent surface with unique
hydrogel silicone and an efficient 10°C - 21 hours; 10°C - 15 hours;
Minimum Overcoating Time fouling release and self-cleaning Minimum Overcoating Time
fouling preventing biocides to boosts 20°C - 8 hours; 20°C - 15 hours;
(self) properties and allows high fuel (self)
the antifouling barrier and prolong the 30°C - 6 hours 30°C - 15 hours
saving potential compared to
fouling-free period. 10°C - 24 hours; 10°C - 24 hours;
traditional antifoulings.
Possesses a high fuel saving potential Minimum Time To Immersion 20°C - 24 hours; Minimum Time To Immersion 20°C - 24 hours;
30°C - 24 hours 30°C - 24 hours
and is also suitable for vessels
Topcoats
Mixed VOC (g/L) 260 Recommended use Mixed VOC (g/L) 260
operating with long service intervals
(up to 60 months) and/or very long
idle periods (up to 120 days). As a fouling release finish on all
Shades and Can sizes boat types with service speeds Shades and Can sizes
above 8 knots. The product can
Recommended use
also be used for propellers.
19740 59161 Hempasil X3+ does not contain 19990 30170 59151 15150
As a fouling defence finish on all boat
Speciality products
types, with no limitation on service organotin compounds acting as
speeds, including slow/ultraslow Olive Black Red biocides and complies with the Black Blue Red Grey
yachts. The product is also suitable 5 | 20L 5 | 20L International Convention on the 20L 20L 20L 20L
for propellers. Control of Harmful Antifouling
Application details Systems on Ships as adopted by
Does not contain organotin IMO, October 2001 Application details
compounds acting as biocides and Base 89909 + Crosslinker 98980 (IMO document AFS/CONF/26).
complies with the International Mixing ratio
17.8 : 2.2 by volume Base 87509 + Crosslinker 98951
Convention on the Control of Harmful Mixing ratio
Thinner Do not dilute 17.8 : 2.2 by volume
Antifouling Systems on Ships as
32 33
Yacht Pro / Fouling Control Systems / Fouling Release Yacht Pro / Fouling Control Systems / Fouling Release
Fouling Control
Biocide-free, high solid, fouling High solid, silicone-based tiecoat
Systems
Finish Glossy Finish Semi-Gloss
release coating. Based on for Hempel's Silic One. Secures
silicone, a hydrogel micro Volume Solids (% - ±2 ) 80 adhesion between Hempel's Light Volume Solids (% - ±2 ) 67
layer provides a smooth, low Theoretical Spreading Rate 10 m²/L – 100 μm WFT Primer or Hempel's Conversion Theoretical Spreading Rate 6.7 m²/L – 100 μm WFT
friction surface which prevents 10°C - 16 hours; Primer and Hempel's Silic One. 10°C - 16 hours;
organisms attaching to the hull Minimum Overcoating Time Minimum Overcoating Time
20°C - 16 hours; 20°C - 8 hours;
(self) (self)
and propellers. Service life of 30°C - 8 hours 30°C - 4 hours
Recommended use
Hempel's Silic One on the hull 10°C - 36 hours; 10°C - 16 hours;
is 2 years. Minimum Overcoating Time
Minimum Time To Immersion 20°C - 24 hours; For use below the waterline 20°C - 8 hours;
(other)
30°C - 24 hours 30°C - 4 hours
between Hempel’s Light Primer
Topcoats
Mixed VOC (g/L) 119 45550 or Hempel's Conversion Mixed VOC (g/L) 233
Recommended use
Primer 45441 and Hempel’s Silic
One 77450. Also used to touch-up
As a fouling release finish on all
Shades and Can sizes and repair damaged areas. Shades and Can sizes
boat types. For use below the
waterline, on propellers and on
running gear.
19990 59151 30390 23410
Speciality products
Black Red True Blue Yellow
2.5L 2.5L 2.5L 2.5L
Hempel's Materials
Steel / Aluminium / GRP /
Stainless Steel
Hempasil Nexus II Materials
Steel / Aluminium / GRP /
Stainless Steel
Fouling Control
Two-component epoxy to Three-component silicone-
Systems
Finish Flat Finish Semi-Gloss
enable easy conversion from based tiecoat with
antifouling to Hempel’s Silic Volume Solids (% - ±2 ) 36 anticorrosive properties. Volume Solids (% - ±2 ) 56
One Fouling Release System. Theoretical Spreading Rate 3.6 m²/L – 275 μm WFT Theoretical Spreading Rate 5.6 m²/L – 175 μm WFT
10°C - 4 hours; Recommended use Minimum Overcoating Time
Minimum Overcoating Time N/A
Recommended use 20°C - 2 hours; (self)
(self)
30°C - 1 hour 10°C - 5 hours;
For use below the waterline Minimum Overcoating Time
For use as a sealer on 10°C - 4 hours; as a tiecoat between epoxy 20°C - 4 hours;
Minimum Overcoating Time (X-Tend 27500)
antifouling. Secures adhesion 20°C - 2 hours; primer and finish coat for 30°C - 3 hours
(other)
30°C - 1 hour 10°C - 12 hours;
between antifouling and the Hempaguard®/Hempasil
Topcoats
Minimum Overcoating Time
Hempel’s Silic One Tiecoat Mixed VOC (g/L) 542 Systems. 20°C - 6 hours;
(X3+/X7)
27450. For use on all 30°C - 4 hours
substrates excluding wood. Can also be used to easily Mixed VOC (g/L) 400
Can be applied on previously Shades and Can sizes convert aged antifoulings to
painted antifouling in good Hempaguard or Hempasil
condition. systems providing antifouling Shades and Can sizes
50711 is in good condition.
Speciality products
Light red 11070
2.5L
Light Grey
20L
Application details
27500
One-component tiecoat
Fouling Control
High solids, silicone-based
Systems
Finish Semi-Gloss
humidity curing tiecoat for
Hempaguard®/Hempasil finishes. Volume Solids (% - ±2 ) 65
Theoretical Spreading Rate 5.4 m²/L – 175 μm WFT
Recommended use Minimum Overcoating Time
N/A
(self)
For use below the waterline as a 10°C - 21 hours;
Minimum Overcoating Time
tiecoat, in combination with 20°C - 8 hours;
(X3+/X7)
Nexus II 27400, between epoxy 30°C - 6 hours
primer and finish coat for the Mixed VOC (g/L) 254
Topcoats
Hempaguard®/Hempasil Systems.
Speciality products
Yellow
damaged areas of existing silicone
5 | 20L
finish coats.
Application details
* compared to
Hempel's Nexus II 27400
40
Yacht Pro / Topcoats Yacht Pro / Topcoats
52140 55810
One-component glossy enamel Two-component high-gloss
polyurethane
Glossy alkyd enamel which Finish High-Gloss Two-component polyurethane Finish High-Gloss
forms a flexible weather topcoat with very good gloss
resistant coating. Resistant Volume Solids (% - ±2 ) 46 and colour retention. Volume Solids (% - ±2 ) 64
to salt water, oils, fuel and Theoretical Spreading Rate 15.3 m²/L – 75 μm WFT Theoretical Spreading Rate 16 m²/L – 60 μm WFT
other lubricants. 10°C - 16 hours; 10°C - 24 hours;
Minimum Overcoating Time Recommended use Minimum Overcoating Time
20°C - 8 hours; 20°C - 16 hours;
(self) (self)
30°C - 6 hours 30°C - 8 hours
Recommended use Mixed VOC (g/L) 429 Above the water as a high-gloss Mixed VOC (g/L) 369
decorative finishing coat in
Above the waterline as a severely corrosive atmospheric
Topcoats
general purpose finishing environments.
coat in alkyd systems. Shades and Can sizes Shades and Can sizes
For use on exterior and
interior steel and woodwork
in mildly to moderately 10000 19990 11480 30100
corrosive environment.
White Black Multitint Mid Grey Navy Blue Multitint
5 | 20L 5 | 20L 5 | 20L 5L 5L 5 | 20L
Speciality products
Application details Application details
Health
Thinners
Cleaners
& Safety
&
42 42 43 43
Yacht Pro / Topcoats Yacht Pro / Topcoats
Glossy polyurethane coating Finish Glossy Quick-drying, acrylic, semi- Finish Flat
with good gloss and colour gloss topcoat containing
retention. Volume Solids (% - ±2 ) 67 fine granules for an Volume Solids (% - ±2 ) 48
Theoretical Spreading Rate 8.3 m²/L – 120 μm WFT anti-slip finish. Durable Theoretical Spreading Rate 9.2 m²/L – 100 μm WFT
10°C - 12 hours; with good resistance to 10°C - 7 hours;
Recommended use Minimum Overcoating Time weathering and abrasion. Minimum Overcoating Time
20°C - 6 hours; 20°C - 4 hours;
(self) (self)
30°C - 3 hours 30°C - 3 hours
Above the water as a Mixed VOC (g/L) 342 Mixed VOC (g/L) 471
glossy decorative finishing Recommended use
coat in severely corrosive
Topcoats
atmospheric environments. For use on glass fibre,
Shades and Can sizes wood and steel. For interior Shades and Can sizes
and exterior use above the
waterline.
40640 50630
Speciality products
Application details Application details
Health
Thinners
Cleaners
& Safety
&
44 44 45 45
Thinners &
Speciality products Thinners & Cleaners Health & Safety
Cleaners
47
Speciality products
46
Yacht Pro / Speciality products Yacht Pro / Speciality products
Hempadur Material
Steel Hempel’s High Protect II Material
Glass fibre
35560 35780
Two-component epoxy tank primer Two-component epoxy
osmosis repair coating
Solvent-free, epoxy primer for Finish Glossy Solvent-free, high-build epoxy Finish High-Gloss
use in fresh water (potable) for osmosis protection and
tanks. Volume Solids (% - ±2 ) 100 treatment. Easy to apply Volume Solids (% - ±2 ) 100
Theoretical Spreading Rate 5 m²/L – 200 μm WFT with good tolerance to Theoretical Spreading Rate 11 m²/L – 150 μm WFT
10°C - 40 hours; environmental conditions. 10°C - 20 hours;
Recommended use Minimum Overcoating Time Forms a hard, tough, water- Minimum Overcoating Time
20°C - 16 hours; 20°C - 8 hours;
(self) (self)
30°C - 8 hours resistant coating. 30°C - 4 hours
As a lining in potable water Minimum Overcoating Time 10°C - 20 hours;
tanks and pipelines. N/A Minimum Overcoating Time
(other) 20°C - 8 hours;
(other)
Mixed VOC (g/L) 0 Recommended use 30°C - 4 hours
Mixed VOC (g/L) 34
Certificates/Approvals For use as a primer for the
prevention and repair of
Approved by WRAS for potable Shades and Can sizes osmotic blistering in the
Shades and Can sizes
water up to 35°C. glass fibre.
20320 50900
Certified by NSF International to
13700 24700
NSF/ANSI standard 61 - Drinking
Speciality products
Water System Components - Cream Light Red
Health Effects. 19.4L 19.4L Grey Cream
2.5L 2.5L
Application details
Application details
Base 35569 + Curing agent 98560
Mixing ratio
3.4 : 1 by volume Base 35789 + Curing agent 95078
Mixing ratio
Thinner Do not dilute • Suitable above & 1.5 : 1 by volume
• Perfect for potable below the waterline
Health
Thinners
Cleaners
& Safety
&
48 48 49 49
Yacht Pro / Speciality products Yacht Pro / Topcoats
11150
Speciality products
Light Grey
2.5 | 5L
Application details
Health
Thinners
Cleaners
& Safety
&
50 50 51 51
Thinners &
Thinners & Cleaners Health & Safety
Cleaners
53 53
Thinners & Cleaners
52
Yacht Pro / Thinners & Cleaners
Thinners
Product name & Quality Uses Can size (L) Health & Safety
For antifoulings, one-component primers,
Hempel’s Thinner 08080 5 & 20
one-component topcoats, two-component topcoats
Cleaners
Product name & Quality Uses Can size (L)
Hempel's Degreaser 99611 For removing grease and oils from metal surfaces 1
Health
Thinners
Cleaners
& Safety
&
54 54 55
Yacht Pro / Health & Safety Yacht Pro / Health & Safety
Your safety is important to us, this section is intended to make it easier Personal Protective Equipment is used to protect workers in a specific work situation against health and
safety risks where other controls can’t provide total protection. PPE may also be required according to national
for you to find the information you need to work safely with Hempel legislation. Make sure that you check the manufacturer's recommendation to ensure that it is appropriate for the
products. It is important that before starting work you: product you are working with. Damaged, dirty or used PPE may not be fully effective and you should maintain it
according to recommendations from the supplier. If in any doubt, replace old equipment before starting work.
•
•
Ensure the area is safe to work in, with appropriate ventilation for the task ahead.
Consider others working around you are also safe from exposure.
General good practice
• Confirm that personal protective equipment (PPE) is used according to manufacturer’s recommendations.
• Read the label, Safety Data Sheet (SDS) and other advice specific to the products you are working with. Handling and Storage
• Read the Safe Use Mixture Information (SUMI) attached to SDS.
• Comply with local laws and regulations. Read the Product Data Sheet (PDS) and the Safety Data Sheet carefully as they contain information related
to how to protect yourself and what to do in case of an accident. Access to both PDS and SDS shall be readily
Hempel hopes that the Health and Safety section will increase awareness and inspire others to learn more about available on hempel.com
how to avoid risks to health and safety.
Self-reactive substances and mixtures • Always read the label thoroughly and contact us • Do not store the paint in direct sunlight.
Organic peroxides if you’re not sure how to use the products. • A paint locker must be well ventilated and the light installed
• Wear appropriate personal protective must be explosion proof. The locker must be in compliance
The main hazard and precautionary information is Flammable gases, aerosols, liquids or solids Self-reactive
with local legislation.
substances and mixtures. Pyrophoric liquids and solids. equipment (PPE).
provided on labels alongside pictograms related to Self-heating substances. Substances, which in contact with • When painting, protect the cans from dust and dirt.
• Provide adequate ventilation for the product
the hazard associated with the product. This should water, emit flammable gases. Organic peroxides
• Keep the lids closed during storage.
used. If necessary, use a respirator. Don’t
be your first reference in understanding how to handle Oxidising substances
• Secure all cans from falling down in bad weather.
breathe vapour/spray.
the product safely. The Safety data sheet provides • Do not leave thinners in open cans during storage.
• Open cans with care.
you with more detailed information. By using the • Using thinner will often lower the flash point and create a
Gas under pressure • Immediately clean up spills. higher potential risk of explosion.
information provided in the SDS and the label, you can Compressed gasses. Liquefied gasses
• Do not eat or drink in the vicinity of stored or • Extra ventilation is required when using thinners as cleaning
make sure that it is safe to use the product where you Refrigerated gasses. Dissolved gasses
applied paint. agent.
work. Corrosive
Corrosive to metals
• Do not swallow. If swallowed, immediately seek • Do not smoke or use open fire when handling paints.
Skin corrosion medical advice and show the container/label. • Spillages must be cleaned up immediately.
The Safety Data Sheet provides detailed information Severe eye damage
• All waste paint must be stored in special containers
• Some products may cause irritation, always
about a hazardous product, including: Its identity and Toxic (acute health hazard) Acute toxicity - via inhalation, skin • Personal protection such as gloves/goggles and often
contact or ingestion. These substances/mixtures can cause seek medical advice if you’re concerned.
its ingredients; Its physical, health and environmental respirators must be used when handling paints.
death, injury or seriously harm health within 72 hours of a single
• Where possible, removed waste antifouling
hazards; Workplace exposure standards; Safe exposure
paint, e.g. waste paint in cans and old paint
handling and storage procedures; First aid procedures; Harmful
Irritant to eyes and skin scraped off of hulls, should be collected and
Transport information and other useful information. Skin sensitization
Respiratory tract irritation disposed of safely.
It is divided into 16 sections. Annexed to SDS is the Narcotic effects
• Contact your local authority for information on
Safe Use Mixture Information. One SUMI represents Chronic health hazard waste disposal.
one specific application setup and provides detailed Products, which are Carcinogenic (can cause cancer), Mutagenic
(can permanently change DNA), Reproductive toxic (can cause
information like ventilation, duration of use and impaired fertility/birth defects), Respiratory sensitizers (can
cause e.g. asthma)
required PPE in a short easy readable one-pager.
Hazardous to environment
Environmental effects - both acute and chronic
Safety data sheets are available on hempel.com
Health
Thinners
Cleaners
& Safety
&
56 57 57
Yacht Pro / Health & Safety Yacht Pro
Paint application
Spray equipment
Personal Protection
Ensure you wear suitable protective clothing, including gloves and glasses. Read labels carefully and follow all
application and health & safety advice. Open cans with care. Don’t eat or drink in the vicinity of stored or applied paint.
What are the hazards The equipment to use What are the hazards The equipment to use
Chemical splash, dust, Safety spectacles, goggles, Damage to inner ear from loud Ear defenders, ear muffs,
paint particles and droplets, face shields, visors. or constant noise levels. ear plugs.
projectiles, vapour.
Eye Hearing
Breathing dust, vapour, fumes, Short term filtering mask Chemical or paint splash, Overalls, coveralls.
aerosols, oxygen-deficient against dust while sanding. spray from spray guns, impact
atmospheres, paint particles. Half facemask for sanding or penetration, dust, excessive
and painting, can be wear or entanglement of own
disposable or with replaceable clothing.
Breathing Body
filter cartridges. Full air feed
facemask for spray painting.
Abrasion, cuts and punctures, Leather gloves, latex gloves, Wet, slipping, cuts and Steel toe protection and
impact, chemicals, solvents, armlets. punctures, falling objects, anti-slip soles. May be a
liquid paints, skin infection. chemical and paint splash, prerequisite on some sites.
abrasion.
Hands Feet
Dust, dirt, oil and grease, paint Barrier cream: short term Impact from falling objects, A range of helmets and bump
particles. protection. head bumping, hair caps.
Cleaning cream: designed entanglement.
to remove contaminates and
Thinners &
cause least skin damage.
Cleaners
Hands Head
Maintenance cream: to help
restore the skin’s natural
protective layers.
58 59
hempel.com
Yacht Pro
Products for professional use
2022/2023
Hempel UK Ltd.
Berwyn House
The Pavillions
Llantarnam Park, Cwmbran
South Wales NP443FD