Professional Documents
Culture Documents
CE3000-UM-251 (15-9370) - Turkce
CE3000-UM-251 (15-9370) - Turkce
CE3000-UM-251 (15-9370) - Turkce
CE3000-40/60/120/120AP/CE2800/SSK/CE3500
CE3000-40Mk2/60Mk2/120Mk2
CE3000-40CRP (Craft ROBO Pro)
SERVICE MANUAL
CE3000-UM-251-15-9370
HISTORY OF REVISIONS
No. Date issued Description of revision Page Edition
1 03.05.21 First Printing All 01
2 03.07.01 Section 10.2 added. v 02
3 03.07.16 The moving coil PL603 added. 10-6 03
4 03.08.06 Part number for the pen block assy corrected. 4-1,10-5 04
5 03.08.06 Part number for the brush bracket corrected. 10-4 04
6 03.08.29 The DIP switch setting for moving coil PL603 added. 7-1,7-3 05
7 03.10.17 Part number for the pen block assy corrected. 10-5 06
8 03.10.22 Part number for the main board corrected. 4-1,10-1 07
9 03.10.22 Sentence number corrected. 7-8 07
10 04.02.05 The default factory settings label location added. 7-2 08
11 04.02.05 Quantity of the roll stocker corrected. 10-8 08
12 04.07.15 CE3000-120AP information added. All 09
13 04.12.01 J1 and J6 were opposite. Corrected. 11-1,11-2,11-3 10
14 05.01.19 Part number for the main board of CE3000-120AP corrected. 4-1,10-1 11
15 05.03.04 The part number of center cover added for the CE3500 and CE2800/SSK. 10-1,10-2 12
16 05.03.04 The part number of side covers added for the CE3500 and CE2800/SSK. 10-1,10-2 12
17 05.03.04 The part number of emblems added. 10-1,10-2 12
18 05.03.04 The part number of caution label added. 10-1,10-2 12
19 05.03.04 The part number of the rating label added. 10-1,10-2 12
20 05.03.04 The part number of the main board added for the CE3000-Mk2. 4-1,10-1 12
21 05.03.04 The part number of the MK2 label added for the CE3000-Mk2. 10-1,10-2 12
22 05.03.04 Note for the CE3000Mk2 added. 7-12 12
23 05.06.24 The procedure for the distance adjustment corrected. 7-6 13
24 05.12.05 CE3000-40CRP information added. All 14
25 06.02.21 Some parts for the CE3500 added. 10-1 15
CE3000-UM-251-9370 ii
CONTENTS
1. INTRODUCTION ..................................................................1-1
1.1 Main Specifications ................................................................................................... 1-1
1.2 External Dimensions .................................................................................................. 1-3
2. PARTS NAMES and FUNCTIONS ..........................................2-1
2.1 Parts Names and Functions ....................................................................................... 2-1
2.2 Assembling the Stand ................................................................................................2-6
2.3 Attaching the Basket (CE3000-60/120: Optional) .................................................... 2-13
3. OPERATIONS .................................................................... 3-1
3.1 Control Panel ............................................................................................................3-1
3.2 Menu List ..................................................................................................................3-2
3.3 Description of Special Functions A .............................................................................3-5
3.4 Description of Special Functions B .............................................................................3-7
4. RECOMMENDED PARTS LIST ............................................. 4-1
5. LIST OF TOOLS ................................................................. 5-1
5.1 Tools .........................................................................................................................5-1
5.2 Greasing And Gluing Points........................................................................................5-1
5.3 Subparts List .............................................................................................................5-1
6. DISASSEMBLY AND REASSEMBLY ..................................... 6-1
6.1 Exterior Parts............................................................................................................6-1
6.1.1 How to Replace the Right Side Cover ........................................................................................6-1
6.1.2 How to Replace the Left Side Cover ..........................................................................................6-1
6.1.3 How to Replace the Center Cover .............................................................................................6-2
6.1.4 How to Replace the Front Guide (CE3000-40/60)......................................................................6-3
6.1.5 How to Replace the Front Guide (CE3000-120) ..........................................................................6-4
6.1.6 How to Replace the Rear Guide .................................................................................................6-6
6.2 Mechanical Parts ......................................................................................................6-8
6.2.1 How to Replace the Front and Rear Media Sensors ....................................................................6-8
6.2.2 How to Replace the Push Roller .............................................................................................. 6-10
CE3000-UM-251-9370 iii
6.2.3 How to Replace the Push Roller Arm ....................................................................................... 6-11
6.2.4 How to Replace the Cam Sensor Board ................................................................................... 6-13
6.2.5 How to Replace the Pen Block (without Auto Registration Sensor) ............................................ 6-14
6.2.6 How to Replace the Pen Block (with Auto Registration Sensor) ................................................. 6-16
6.2.7 How to Replace the Push Roller Sensor ................................................................................... 6-18
6.2.8 How to Replace the Y-relay Board ........................................................................................... 6-19
6.2.9 How to Replace the Cutting Mat ..............................................................................................6-20
6.2.10 How to Replace the Control Panel Relay Board, LCD Assembly and Membrane Switch Panel .... 6-21
6.2.11 How to Replace the Y-belt .......................................................................................................6-23
6.2.12 How to Replace the Y-motor (CE3000-60/120) .......................................................................6-25
6.2.13 How to Replace the Y-motor (CE3000-40) ...............................................................................6-27
6.2.14 How to Replace the X-motor ...................................................................................................6-29
6.2.15 How to Replace the Y-flexible Cable ........................................................................................6-31
6.2.16 How to Replace the Vacuum Fan .............................................................................................6-34
6.2.17 How to Replace the Main Board ..............................................................................................6-35
6.2.18 How to Replace the Power Supply ...........................................................................................6-36
6.2.19 How to Replace the Drive Roller ..............................................................................................6-37
CE3000-UM-251-9370 iv
7.15 Adjusting the Spacing Between Pen 1 and Pen 2 (CE3000-120AP) ...................................... 7-16
8 SERVICE MODES ................................................................8-1
8.1 Sensor Test Mode ......................................................................................................8-1
8.2 Control Panel Membrane Switch Test Mode ................................................................8-2
9. TROUBLESHOOTING .......................................................... 9-1
9.1 The Plotter is Turned On But Doesn’t Operate .............................................................9-1
9.2 Media Loading Operations .........................................................................................9-2
9.3 Cutting Operations ....................................................................................................9-3
10. PARTS LIST ......................................................................10-1
10.1 Outer Casing ........................................................................................................... 10-1
10.2 Main Frame .............................................................................................................10-3
10.3 Base Assy for CE3000-120 ......................................................................................10-5
10.4 Pen Block ................................................................................................................10-6
10.5 Wiring Harness ........................................................................................................10-8
10.6 Stand (CE3000-120/120AP standard, CE3000-60 optional) .......10-8
10.7 Option Basket ........................................................................................................ 10-12
10.8 Other Parts ........................................................................................................... 10-12
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS ..................... 11-1
11.1 Block Diagrams ....................................................................................................... 11-1
11.1.1 Block Diagram for CE3000-120 .............................................................................................. 11-1
11.1.2 Block Diagram for CE3000-60................................................................................................ 11-2
11.1.3 Block Diagram for CE3000-40 ............................................................................................... 11-3
11.2 Circuit Diagrams ..................................................................................................... 11-4
11.2.1 Main Board Top Section (PR270101A) ..................................................................................... 11-4
11.2.2 Main Board Connector Block Section (PR270101A) ................................................................. 11-5
11.2.3 Main Board CPU Block Section (PR270101A)........................................................................... 11-6
11.2.4 Main Board Motor Drive Section (PR270101A)......................................................................... 11-7
11.2.5 Main Board GRC 1507 Section (PR270101A) ........................................................................... 11-8
11.2.6 Main Board Interface Section (PR270101A) ............................................................................. 11-9
11.2.7 Main Board Memory Block Section (PR270101A) ...................................................................11-10
11.2.8 Main Board USB Block Section (PR270101A) ..........................................................................11-11
CE3000-UM-251-9370 v
11.2.9 Main Board Top Section (PR270102A) ....................................................................................11-12
11.2.10 Main Board Connector Block Section (PR270102A) ................................................................11-13
11.2.11 Main Board CPU Block Section (PR270102A) .........................................................................11-14
11.2.12 Main Board 2-Phase Motor Drive Section (PR270102A) ..........................................................11-15
11.2.13 Main Board Decoding Block Section (PR270102A)..................................................................11-16
11.2.14 Main Board Interface Section (PR270102A) ...........................................................................11-17
11.2.15 Main Board Memory Block Section (PR270102A) ...................................................................11-18
11.2.16 Main Board USB Block Section (PR270102A)..........................................................................11-19
11.2.17 Main Board Pen Drive Section (PR270102A).......................................................................... 11-20
11.2.18 Relay and Sensor Board Section ........................................................................................... 11-21
11.2.19 Control Panel Membrane Switch Panel Section ..................................................................... 11-22
11.2.20 120-Relay Board Section ...................................................................................................... 11-23
11.2.21 120-Pen Encoder Flexible Cable Section (FPC270101) .......................................................... 11-23
CE3000-UM-251-9370 vi
1. INTRODUCTION
1. INTRODUCTION
1.1 Main Specifications
CE3000-40/60/120/40Mk2/60Mk2/120Mk2/40CRP
Item CE3000-40/Mk2/CRP CE3000-60/Mk2 CE3000-120/Mk2
CPU 32-bit CPU
Configuration Grit rolling
Drive system Stepping Digital servo
Maximum cutting area 375 mm x 50 m 603 mm x 50 m 1213 mm x 50 m
Range of guaranteed 356 mm x 2 m*1 584 mm x 5 m*1 1194 mm x 5 m*1
precision
Compatible media widths Minimum: 50 mm Minimum: 50 mm Minimum: 85 mm
Maximum: 484 mm Maximum: 712 mm Maximum: 1346 mm
(19 inches) (28 inches) (52 inches)
Maximum media thickness 10 mil
Maximum cutting speed 40 cm/s (in all directions) 60 cm/s (in all directions) 100 cm/s (45° direction)
Maximum acceleration 5 m/s2 (45° direction) 21.2 m/s2 (45° direction) 14.1 m/s2 (45° direction)
Specifiable cutting speeds 1–10, 15, 20, 25, 30, 35, 40 1–10, 15, 20, 25, 30, 35, 1–10, 15, 20, 25, 30, 35,
cm/s 40, 45, 50, 55, 60 cm/s 40, 45, 50, 55, 60, * cm/s
Cutting force 20 gf to 300 gf (31 levels) 20 gf to 450 gf (38 levels)
Minimum character size Approximately 5 mm for alphanumeric characters (varies depending on the medium,
font, etc.)
Mechanical resolution 0.0125 mm 0.005 mm
Programmable resolution GP-GL: 0.1/0.05/0.025/0.01 mm; HP-GLTM *2: 0.025 mm
Repeatability precision 0.1 mm or less per 2 m*1
No. of pens mountable 1 pen
Compatible cutter type Supersteel cutter blades
Compatible pen type Water-based fiber-tip pens
Compatible cutting film Marking film (PVC, fluorescent, or reflective film) up to 0.25 mm in thickness
(excluding high-luminosity reflective film)
Interfaces RS-232C/Centronics/USB
Buffer capacity 2 MB
Command modes GP-GL, HP-GLTM *2 (selected on the control panel)
Display panel Liquid crystal display (16 characters x 1 row)
Rated power supply 100 to 120 V AC, 200 to 240 V AC, 50/60 Hz
Power consumption 70 VA 100 VA
Operating environment 10°C to 35°C, 35% to 75% RH
Conditions for guaranteed 16°C to 32°C, 35% to 70% RH
precision
External dimensions Approx. Approx. Approx.
(W x D x H) 623 x 285 x 223 mm 851 x 285 x 223 mm 1,487 x 656 x 1188 mm*3
Weight 9.4 kg 11.2 kg 39.1 kg*3
*1: Varies depending on the type of Graphtec-authorized film and the cutting conditions
*2: HP-GLTM is a registered trademark of Hewlett-Packard Company.
*3: Including the stand
CE3000-UM-251-9370 1-1
1. INTRODUCTION
CE3000-120AP
Item CE3000-120AP
CPU 32-bit CPU
Configuration Grit rolling
Drive system Digital servo
Maximum cutting area 1164 mm x 50 m (when the 3-inch core is used)
Maximum guaranteed cutting area 1194 mm x 3 m (when the 3-inch core is used)*1
Compatible media widths 160 to 270, 300 to 400, 440 to 540, 580 to 680, 710 to 810, 850
to 950, 990 to 1090, 1120 to 1220 mm (the effective drawing
area is the maximum obtainable area for the corresponding
medium width)
Compatible maximum media width 3-inch core: 1220 mm
2-inch core: 1180 mm
Maximum loadable media length 100 m/roll
Media types Fine quality paper for apparel patterns (64 to 130 g/m2)
Roll media diameter: 2-inch, 3-inch
Maximum cutting speed 60 cm/s
Maximum acceleration 13.9 m/s2 (45° direction)
Specifiable cutting speeds 1 to 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 cm/s
Cutting force 20 to 300 gf (31 levels)
Mechanical resolution 0.005 mm
Programmable resolution GP-GL: 0.1/0.5/0.025/0.01 mm
HP-GLTM *2: 0.025 mm
Repeatability precision Within 0.1 mm/2m*3
No. of pens mountable 2
Compatible cutter blade type Supersteel
Compatible pen type Water-based fiber-tip pens
Interfaces RS-232C/Centronics/USB
Buffer capacity 2 MB
Command modes GP-GL, HP-GLTM *2 (selected on the control panel)
Display panel Liquid crystal display (16 characters x 1 row)
Rated power supply 100 to 120 V AC, 200 to 240 V AC, 50/60 Hz
Power consumption 100 VA
Operating environment 10°C to 35°C, 35% to 75% RH
Conditions for guaranteed precision 16°C to 32°C, 35% to 70% RH
External dimensions (W x D x H) Approx. 1,487 x 656 x 1189 mm*4
Weight 43 kg*4
*1: Depending on the shape of the roll stoppers, the width will be 1140 mm when a 2-inch core is used.
*2: HP-GLTM is a registered trademark of Hewlett-Packard Company.
*3: When using Graphtec-specified media and cutting conditions.
*4: Includes the stand and basket.
CE3000-UM-251-9370 1-2
1. INTRODUCTION
322
623
(221)
223
285
443
Units: mm
Dimensional accuracy: ±5 mm
CE3000-60/Mk2
851
322
(221)
223
285
443
Units: mm
Dimensional accuracy: ±5 mm
CE3000-UM-251-9370 1-3
1. INTRODUCTION
851
1004
585
Units: mm
Dimensional accuracy: ±5 mm
CE3000-120/Mk2
1487
1188
656
Units: mm
Dimensional accuracy: ±5 mm
CE3000-UM-251-9370 1-4
1. INTRODUCTION
CE3000-120AP
����
����
����
Units: mm
Dimensional accuracy: ±5 mm
CE3000-UM-251-9370 1-5
2. PARTS NAMES and FUNCTIONS
Control panel
Parallel (Centronics)
interface connector
Serial (RS-232C)
interface connector
Push rollers
USB interface
connector
Power switch
AC power inlet
Roll-medium trays
Roll-medium-tray
guide rail
CE3000-UM-251-9370 2-1
2. PARTS NAMES and FUNCTIONS
Control panel
Parallel (Centronics)
interface connector
Serial (RS-232C)
interface connector
Push rollers
USB interface
connector
CE3000-UM-251-9370 2-2
2. PARTS NAMES and FUNCTIONS
Power switch
AC power inlet
Stock rollers
Stoppers
Stand
CE3000-UM-251-9370 2-3
2. PARTS NAMES and FUNCTIONS
�����������
�������������
����������� ������
�����������
������������ ���������
����������������������
�������������������
����
�������������������
�����������������
�������������������
�������
����������� ������������
CE3000-UM-251-9370 2-4
2. PARTS NAMES and FUNCTIONS
������������
��������������
�����
������
���������������
CE3000-UM-251-9370 2-5
2. PARTS NAMES and FUNCTIONS
Stand Construction
The stand is made up of the following parts.
CE3000-120
CE3000-120
Front Front
(2) Fasten the stand tops (L/R) to the stand side bars (L/R) with the hexagonal socket bolts (M5), using the
Allen wrench.
CE3000-60 CE3000-120 Hexagonal
Hexagonal socket bolt (M5)
socket bolt (M5)
Stand top
Stand top
Stand side bar
Stand side bar
CE3000-UM-251-9370 2-6
2. PARTS NAMES and FUNCTIONS
(3) Loosely fasten the stand side bars (L/R) to the center bar with the hexagonal socket bolts (CE3000-60:
M5, CE3000-120: M6), using the Allen wrench.
CE3000-60
Center bar
Hexagonal
socket bolt
(M6)
CE3000-120
(4) Mount the CE3000 cutting plotter on the stand by inserting the positioning pins on the stand into the
positioning holes on the underside of the cutting plotter. Fasten using the four coin screws or hexagonal
socket bolts (M6).
CE3000-60
Positioning pins
Stand
CE3000-120
Positioning pins
Stand
CE3000-120
Hexagonal socket
bolts (M6)
CE3000-UM-251-9370 2-7
2. PARTS NAMES and FUNCTIONS
CE3000-120AP:Standard
Stand Construction
The stand is made up of the following parts.
Stand side bar (L/R) Center bar Hexagonal socket bolt (M6) x 8
Alignment shaft
Stock shaft
Basket Construction
Sheet support pipe bracket x 2 Rubber cap x 4 Hexagonal socket bolt (M6) x 4
CE3000-UM-251-9370 2-8
2. PARTS NAMES and FUNCTIONS
����������
����������
��������������
����������
����������������
(2) Fasten the sheet support pipe brackets to the stand tops with the hexagonal socket bolts (M6).
��������������������
��������������������������
CE3000-UM-251-9370 2-9
2. PARTS NAMES and FUNCTIONS
(3) Insert the sheet support pipes into the sheet support pipe brackets. Use the lower holes for the pipe that
will be at the front of the cutting plotter, and the upper holes for the pipe that will be at the rear.
Remove the tape from the ends of the pipes to expose the adhesive, and then fit the rubber caps on
firmly.
������������������
����������
��������������
(4) Attach the alignment shaft to the top of the stand. Loosen the attached bindhead screws A (M4) two or
three turns, and then insert the brackets on the end of the shaft using the elongated screw holes. Tighten
the screws to hold the brackets in place. Push the shaft in until it contacts the curved area indicated by “a”
in the figure below, and then tighten the A (M4) bindhead screws.
When the shaft has been attached, tighten the bindhead screws B (M4), and check that the shaft does
not rotate. The bindhead screws B are screws to prevent the shaft from rotating. Position the shaft as
desired (check both the rotation direction and the horizontal direction) and then tighten the screws.
����������������
�������
CE3000-UM-251-9370 2-10
2. PARTS NAMES and FUNCTIONS
(5) Mount the CE3000-120AP on the stand by inserting the positioning pins on the stand into the positioning
holes on the underside of the cutting plotter and then fasten with the four hexagonal bolts (M6).
Make sure that the casters with the stoppers are at the front.
�������������
���������������
���������������
�����
����������
����������������
(6) Attach the media guide bracket to the underside of the front panel. Loosen the six bindhead screws (M3)
two or three turns, and then slot the bracket in. Tighten the screws to hold the bracket in place.
�������������������
(7) Tighten all the hexagonal bolts that were temporarily fastened in step 1.
CE3000-UM-251-9370 2-11
2. PARTS NAMES and FUNCTIONS
(8) Pull out the sheet support pipes, and attach the sheet to them. Pass the sheet under the center bar, and
fasten the ends to the support pipes using the press-studs.
������������������
����������
�������������������������
�����
(9) Attach the stoppers (L/R) to the stock shaft and then attach the shaft to the top of the stand.
�������
�����������
������
CE3000-UM-251-9370 2-12
2. PARTS NAMES and FUNCTIONS
Stand top
CE3000-60
Sheet support pipe
Stand top
CE3000-120
CE3000-UM-251-9370 2-13
2. PARTS NAMES and FUNCTIONS
(3) Mount the CE3000 cutting plotter on the stand by inserting the positioning pins on the stand into the
positioning holes on the underside of the cutting plotter. Fasten using the four coin screws or hexagonal
socket bolts (M6).
CE3000-60
Positioning pins
Stand
CE3000-60
Coin screws
CE3000-120
Positioning pins
Stand
Hexagonal
socket bolts (M6)
CE3000-120
(4) Pull out the sheet support pipe and attach the sheet. Divide the sheet over the center bar, and then
fasten the sheet to the sheet support pipe using the press-studs.
CE3000-60
Sheet
Devide over
the center bar
Press-studs
CE3000-120
Sheet
CE3000-UM-251-9370 2-14
3. OPERATIONS
3. OPERATIONS
3.1 Control Panel
Indicator Lamp
STATUS .....Illuminates while the power to the cutting
plotter is turned on, and goes out when
the cutting plotter is in PAUSE status.
This lamp flashes when data is being
received from an interface, regardless
of whether or not the cutting plotter is in
PAUSE status.
Panel Keys
TEST..........Press this function key to conduct
a cutting test and check the cutting
conditions.
PREV. ........Press this function key to view the
previous display on the LCD when in
PAUSE status.
NEXT .........Press this function key to view the next
display on the LCD when in PAUSE
status.
COND. .......Press this function key to view the cutter-
pen condition settings.
PAUSE.......Press this function key once in READY status to switch to PAUSE status in order to change
the various settings. Press it again to cancel the PAUSE status. Pressing this key while
cutting or plotting is in progress stops the cutting or plotting.
ENTER ......Pressing this function key registers the cutting or plotting conditions set.
POSITION .These keys are used to move the cursor or change the settings on the LCD display on the
function setting screens. Press these keys when in PAUSE status to move the pen carriage
or the medium.
ORIGIN ......Press this function key to set the origin point. The pen position is set as the origin point when
this key is pressed.
CE3000-UM-251-9370 3-1
3. OPERATIONS
CE3000-40/60/120
CE3000-UM-251-9370 3-2
3. OPERATIONS
CE3000-120AP
������������ ��������������������������
�������� �������������������������������
� � � � � � �� � � � � � � � � ��������������������������������������������������
����������� ����������������������������
� � � � � � � � � ���� ��������������������������������������
�� � � � � � � � � �����������������������
� � � ��� � ������������������������������������������
������������ ������������������������
������������ ����������������������������������
������������� ���������������������
(ENTER) key
� � �� � � � � � � � � � �
����������
(ENTER) key
���� ���������
� � � �� � � � � � � � � � � �������������������
�������������� ����������������������������
� � �� � �� � � ������������������������������ � �� � � � � � � � ����������������������������������
� � � ��� � � � � � � � � � � ������������������������������
� � � � � �� � � ���������������������
������������ ������������������������
����� ��������������������������
����������� �����������������������
����������� ������������������������������������������
��������
���� �����������������������������������������
���������������
CE3000-UM-251-9370 3-3
3. OPERATIONS
��������������� ����
���� �������
������������� �������
�������������� �����������
������������ ����
�������������� ������������
��������������� ������������
����������� ������������
��������� ���������
������ ����������������
������ �����������
������ ����������������
����
CE3000-UM-251-9370 3-4
3. OPERATIONS
���������������� ����������������
���������������� ����������������
���������������� ����������������
���������������� ����������������
���������������� ����������������
���������������� ����������������
���������������� ����������������
���������������� ����������������
(2) Scroll up or down to select the required menu using the (NEXT) or (PREV.) keys.
(3) Select the setting details using the and keys, and press the (ENTER) key to register the setting. To
cancel, press the (NEXT) or (PREV.) key. The next menu is displayed.
(4) Once all the settings have been made, turn off the cutting plotter.
¡Enabling/Disabling the “:” and “;” Commands (when the COMMAND setting is GP-GL)
This function enables or disables the “:” and “;” commands when the COMMAND setting is GP-GL. If
the first part of the data is lost, these commands may be having an adverse effect. In this case, set this
function to DISABLED (the default setting is ENABLED).
¡Moving the Pen While Raised or Lowered in Response to the “W” Command (when the COMMAND
setting is GP-GL)
This function selects whether, upon receipt of the “W” command for the drawing of arcs, the cutting
plotter moves the pen to the specified starting position, raised or in the pen status (raised or lowered)
that was in effect immediately prior to receipt of the “W” command.
When PEN DOWN is selected, the pen is moved to the starting position for the drawing of arcs in the
pen status (raised or lowered) that was in effect immediately prior to receipt of the “W” command.
When PEN UP is selected, the pen is moved to the starting position for the drawing of arcs in the raised
status. This setting is only effective if a cutter blade has been selected in the cutter-pen settings.
(The default setting is PEN UP.)
CE3000-UM-251-9370 3-5
3. OPERATIONS
¡SETTING PRIORITY
This function sets whether the cutting plotter places priority on the cutting conditions specified through
command input from the computer or through manual settings (on the cutting-plotter control panel).
When MANUAL is selected, cutting is performed using the cutting conditions set at the control panel,
and cutting conditions sent from the computer are ignored.
When PROGRAM is selected, cutting is performed using the cutting conditions specified in a received
cutting-condition command. If no commands are received, cutting is performed using the cutting
conditions set at the control panel.
(The default setting is MANUAL.)
CE3000-UM-251-9370 3-6
3. OPERATIONS
DISPLAY ENGLISH
(2) Use the and keys to select the desired display language, and then press the (ENTER) key to
confirm. To cancel, press the (NEXT) or (PREV.) key.
(3) Once all the settings have been made, turn off the cutting plotter.
CE3000-UM-251-9370 3-7
4. RECOMMENDED PARTS LIST
CE3000-UM-251-9370 4-1
5. LIST OF TOOLS
5. LIST OF TOOLS
5.1 Tools
No. Adjustment Item Jig Tool
1 Pen force adjustment Cutter Pen Holder (CB09) Colex gauge (50,300,500 gf)
2 Distance adjustment Glass scale
3 Pen block height adjustment 10 mm height block
4 Firmware update PC, Centronics I/F cable
5 X-drive belt tension adjustment Push-pull gauge (2 kg)
6 Y-drive belt tension adjustment Push-pull gauge (2 kg)
7 Replacing the main board
Short screwdriver (50 mm)
8 Replacing the vacuum fan
CE3000-UM-251-9370 5-1
6. DISASSEMBLY AND REASSEMBLY
M4L6 binding
head screw Center cover
M4L6 binding
head screw
(1) Remove the three M4L6 binding head screws from the left side cover.
CE3000-UM-251-9370 6-1
6. DISASSEMBLY AND REASSEMBLY
(1) Remove the two M3L6 TP screws from the center cover.
M4L6 binding
head screw Center cover
M4L6 binding
head screw
CE3000-UM-251-9370 6-2
6. DISASSEMBLY AND REASSEMBLY
Front guide 60
M3L6 binding
head screw
Front guide 40
M3L6 binding
head screw
CE3000-UM-251-9370 6-3
6. DISASSEMBLY AND REASSEMBLY
M3L6 TP
head screw
Measuring tape
(2) Clean the surface of the front guide 120 with alcohol at the locations where the measuring tapes will be
affixed.
(3) Affix the measuring tapes as shown in the above figure.
CE3000-UM-251-9370 6-4
6. DISASSEMBLY AND REASSEMBLY
M3L6 TP
head screw
(5) Slide in the front guide 120 and hook the notch to the main frame as shown in the above figure.
(6) Fasten the three M4L6 TP head screws.
CE3000-UM-251-9370 6-5
6. DISASSEMBLY AND REASSEMBLY
M3L6 binding
head screw
Rear guide
M3L6 binding
head screw
Notch
CE3000-UM-251-9370 6-6
6. DISASSEMBLY AND REASSEMBLY
CE3000-UM-251-9370 6-7
6. DISASSEMBLY AND REASSEMBLY
M3L12
binding head
screw
Connector 2.5 mm
2 mm
Sensor
Fold the cutting film at this edge
Cutting film and attach it to the side of the sensor.
Align the cutting film edge with the connector edge.
CE3000-UM-251-9370 6-8
6. DISASSEMBLY AND REASSEMBLY
(3) Fasten the M3L12 binding head screw to mount the sensor.
(4) Install the rear guide.
CE3000-UM-251-9370 6-9
6. DISASSEMBLY AND REASSEMBLY
(2) Detach the push roller shaft from the push roller arm from the left side.
(3) Detach the push roller.
CE3000-UM-251-9370 6-10
6. DISASSEMBLY AND REASSEMBLY
Cam shaft
(5) Remove the M3L6 binding head screw attaching the left side cam shaft holder.
(6) Remove the two M3L6 binding head screws attaching the cam sensor plate to the cam shaft.
CE3000-UM-251-9370 6-11
6. DISASSEMBLY AND REASSEMBLY
Cam
Cam shaft
(8) Pull out the cam shaft from the right side.
(9) Detach the push roller arm spring from the push roller arm.
(10) Detach the E-ring from the push roller arm shaft.
E-ring
(11) Detach the push roller arm shaft from the push roller arm and detach the push roller arm, push roller arm
base, and the cam.
(2) Reattach the push roller arm in the reverse order in which it was detached.
CE3000-UM-251-9370 6-12
6. DISASSEMBLY AND REASSEMBLY
(3) Remove the M3L6 binding head screw attaching the cam sensor board.
CE3000-UM-251-9370 6-13
6. DISASSEMBLY AND REASSEMBLY
6.2.5 How to Replace the Pen Block (without Auto Registration Sensor)
How to detach the pen block
(1) Detach the center cover (see Subsection 6.1.3).
(2) Loosen the M3L6 binding head screw attaching the pen block cover.
M3L6 binding screw J503
Y-relay board
J504
CE3000-UM-251-9370 6-14
6. DISASSEMBLY AND REASSEMBLY
(5) Remove the two M4L6 binding head screws attaching the pen block.
M4L6 binding
head screw
Pen block
(3) Reattach the other parts in the reverse order in which they were detached.
(4) Perform the pen force adjustment (see Section 7.5).
CE3000-UM-251-9370 6-15
6. DISASSEMBLY AND REASSEMBLY
6.2.6 How to Replace the Pen Block (with Auto Registration Sensor)
How to detach the pen block
(1) Detach the center cover (see Subsection 6.1.3).
(2) Loosen the M3L6 binding head screw attaching the pen block cover.
M3L6 binding screw J503
M2L5 binding screw
Y-relay board
J505
J504
CE3000-UM-251-9370 6-16
6. DISASSEMBLY AND REASSEMBLY
(6) Remove the two M4L6 binding head screws attaching the pen block.
M4L6 binding
head screw
Pen block
10 mm Cutting mat
(3) Reattach the other parts in the reverse order in which they were detached.
(4) Perform the pen force adjustment (see Section 7.5).
(5) Perform the auto registration sensor sensitivity adjustment (see Section 7.8).
(6) Perform the auto registration sensor offset adjustment (see Section 7.9).
CE3000-UM-251-9370 6-17
6. DISASSEMBLY AND REASSEMBLY
M3L6 binding
head screw
(6) Remove the M3L6 binding head screw attaching the push roller sensor board.
(7) Disconnect the push roller flexible cable from the push roller sensor board.
CE3000-UM-251-9370 6-18
6. DISASSEMBLY AND REASSEMBLY
(5) Remove the two M3L6 binding head screws attaching the Y-relay board.
CE3000-UM-251-9370 6-19
6. DISASSEMBLY AND REASSEMBLY
Cutting mat
Vacuum base
(3) Make sure that there is no air between the cutting mat and the vacuum base.
(4) Attach the pen block (see Subsection 6.2.5 or 6.2.6).
(5) Reattach the other parts in the reverse order in which they were detached.
CE3000-UM-251-9370 6-20
6. DISASSEMBLY AND REASSEMBLY
6.2.10 How to Replace the Control Panel Relay Board, LCD Assembly and Membrane Switch Panel
How to detach the control panel relay board, LCD assembly and membrane switch panel
(1) Detach the right side cover (see Subsection 6.1.1).
(2) Disconnect the flexible cables from connector J402 and J403 on the control panel relay board.
(3) Remove the two M3L8 self-tapping screws attaching the control panel relay board.
Right side cover
M3L8
selt-tapping screw
(4) Detach the control panel relay board from the right side cover.
(5) Remove the M3L8 self-tapping screw attaching the LCD assembly.
LCD assembly
Right side cover
(6) Detach the LCD assembly from the right side cover.
(7) Peel off the membrane switch panel from the right side cover.
Membrane switch panel
CE3000-UM-251-9370 6-21
6. DISASSEMBLY AND REASSEMBLY
How to reinstall the control panel relay board, LCD assembly and membrane switch panel
(1) Clean the surface of the right side cover with alcohol where the membrane switch panel was attached.
(2) Reattach the LCD assembly to the right side cover.
(3) Attach the membrane switch panel to the right side cover so that it fits around the LCD window.
(4) Reattach the other parts in the reverse order in which they were detached.
CE3000-UM-251-9370 6-22
6. DISASSEMBLY AND REASSEMBLY
Y-tension bracket
Y-tension arm
Y-tension spring
(6) Remove the four M3L6 binding head screws attaching the right and left Y-belt stopper plates to the
slider.
Y-belt
CE3000-UM-251-9370 6-23
6. DISASSEMBLY AND REASSEMBLY
CE3000-UM-251-9370 6-24
6. DISASSEMBLY AND REASSEMBLY
(5) Remove the two M3L6 binding head screws holding the Y-motor.
(6) Detach the Y-motor pulley, then detach the Y-motor.
(7) Detach the pulley flange and the spacer from the Y-motor.
Y-motor
Spacer
Pulley flange
CE3000-UM-251-9370 6-25
6. DISASSEMBLY AND REASSEMBLY
CE3000-UM-251-9370 6-26
6. DISASSEMBLY AND REASSEMBLY
(4) Loosen the two M3L4WP set screws to detach the Y-motor pulley.
Y-motor
Flange
Y-motor pulley
(5) Remove the two M3L6 binding head screws holding the flange.
(6) Detach the flange from the Y-motor.
CE3000-UM-251-9370 6-27
6. DISASSEMBLY AND REASSEMBLY
CE3000-UM-251-9370 6-28
6. DISASSEMBLY AND REASSEMBLY
(4) Remove the two M3L6 binding head screws holding the X-motor then detach the X-motor.
(5) Disconnect the X-motor cable from its connector(s) on the main board.
CE3000-40: ............. Disconnect the cable from connector J15 on the main board.
CE3000-60: ............. Disconnect the cables from connector J7 and J10 on the main board.
CE3000-120: ........... Disconnect the cables from connector J1102 and J1104 on the Y-motor relay board.
(6) Remove the wiring harness tie-wrap holding the X-motor harness and detach the X-motor.
(7) If you are replacing the X-motor of the CE3000-40, detach the flange from the X-motor.
CE3000-UM-251-9370 6-29
6. DISASSEMBLY AND REASSEMBLY
(11) Spread a suitable quantity of the Shinetu silicon grease G501 on the X-motor pulley.
(12) Move the X-drive pulley and check the tension of the X-drive belt.
(13) Reattach the other parts in the reverse order in which they were detached.
CE3000-UM-251-9370 6-30
6. DISASSEMBLY AND REASSEMBLY
Flexible cable
stopper
Plastic rivet
(9) Remove the Y-flexible cable attached with double-sided adhesive tape to the Y-rail.
CE3000-UM-251-9370 6-31
6. DISASSEMBLY AND REASSEMBLY
(3) Insert the Y-flexible cable into the core and connect the Y-flexible cable to connector J501.
(4) Attach the core to the Y-relay board using double-sided adhesive tape.
(5) Move the pen block to the left end.
CE3000-UM-251-9370 6-32
6. DISASSEMBLY AND REASSEMBLY
(6) Fit the Y-flexible cable into the Y-rail as shown below. The Y-flexible cable shouldn’t touch the left side
plate. Allow a 3-mm space between the left end of the Y-flexible cable and the left side plate.
Allow a 3-mm space between the left end
of the Y-flexible cable and the left side plate.
(7) Secure the Y-flexible cable onto the flexible cable guide of the Y-rail using double-sided adhesive tape.
(8) Reattach the other parts in the reverse order in which they were detached.
CE3000-UM-251-9370 6-33
6. DISASSEMBLY AND REASSEMBLY
5 to 6 cm height
(5) Insert some boxes between the main unit and the chassis to lift the main unit up about 5 to 6 cm from
the chassis.
(6) Remove the harness tie-wrap holding the vacuum fan cables.
(7) Disconnect the vacuum fan from its connector.
CE3000-40 and CE3000-60: connector J9 on the main board.
CE3000-120: connector J1202 or J1203 on the fan relay board.
(8) Use a short screwdriver to remove the two M3L35 binding head screws holding the vacuum fan.
(9) Detach the vacuum fan from the main unit.
CE3000-UM-251-9370 6-34
6. DISASSEMBLY AND REASSEMBLY
RS-232C interface
Centronics interface
(5) Remove the two screws holding the RS-232C interface connector to the chassis.
(6) Disconnect all the cables and flexible cables from their connectors on the main board.
(7) Remove the four M3L6 binding head screws holding the main board.
(8) Detach the main board from the chassis.
CE3000-UM-251-9370 6-35
6. DISASSEMBLY AND REASSEMBLY
Power supply
M3L6 binding
head screw
(3) Remove the two M3L6 binding head screws holding the power supply to the bottom of the chassis.
(4) Detach the power supply from the chassis.
CE3000-UM-251-9370 6-36
6. DISASSEMBLY AND REASSEMBLY
X-drive pulley
X-drive belt
M3L6 binding head screw
(5) Push up the X-motor from inside the left side plate then remove the X drive belt from the X-drive pulley.
(6) Loosen the two M3L4WP set screws holding the X-drive pulley and detach the X-drive pulley from the
drive roller.
(7) Remove the two M3L6 binding screws holding the X-drive roller bearing with a flange.
(8) Slide out the X-drive roller from the unit. There is a bearing stopper flange and a bush on the left side
plate; don’t miss those parts when removing the X-drive roller.
CE3000-UM-251-9370 6-37
6. DISASSEMBLY AND REASSEMBLY
CE3000-UM-251-9370 6-38
7. ELECTRICAL ADJUSTMENTS
7. ELEKTRİKSEL AYARLAR
7.1 DIP Anahtarı Ayarları
Fabrika ön ayarları (Normal Mod)
CE3000-120 ve CE3000-60, CE3000-40, PL-326B hareketli bobinli.
ON
SW1 OFF
1 2 3 4
CE3000-60 ve CE3000-40, yeni hareketli bobin PL-603 ile
Moving coil PL-326B
ON
SW1 OFF
1 2 3 4
NOV-RAM Temizle
ON
SW1 OFF
1 2 3 4 Moving coil PL-603
CE3000-UM-251-9370 7-1
7. ELECTRICAL ADJUSTMENTS
Anahtarlamalı
güç kaynağı
ünitesi
Varsayılan fabrika ayarları
bu alana kaydedilir.
Varsayılan fabrika ayarları aşağıda S/N309xxxxx'ten gösterilen sol taraftaki plakaya kaydedilmiştir.
NOVRAM INIT.
(4) Programlama tamamlandığında NOVRAM INIT. SON menüsü görünür.
CE3000-UM-251-9370 7-3
7. ELECTRICAL ADJUSTMENTS
DISTANCE ADJUST
(6) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
(10) 120g kalem kuvvetini ayarlayın. Ölçülen değer spesifikasyon aralığı dahilindeyse (120±10g) veya
Kaydedilen değeri girdikten sonra ayarı kaydetmek için ENTER tuşuna basın. Bir sonraki belirtilen
kalem kuvveti görünür.
(11) 300g-kalem kuvvetini ayarlayın. Ölçülen değer spesifikasyon aralığı (300±20g) dahilindeyse veya
Kaydedilen değeri girdikten sonra ayarı kaydetmek için ENTER tuşuna basın. Bir sonraki belirtilen kalem gücü
görünür.
(12) 450g kalem kuvvetini ayarlayın. Ölçülen değer spesifikasyon aralığı dahilindeyse (450±20g) veya
Kaydedilen değeri girdikten sonra ayarı kaydetmek için ENTER tuşuna basın.
CE3000-UM-251-9370 7-4
7. ELECTRICAL ADJUSTMENTS
Not: Kalem kuvvetini ayarlarken bunu hızlı bir şekilde yapmak önemlidir. Kalem gücü ayarının geciktirilmesi
aktüatörün sıcaklığını değiştirir ve yapay olarak daha düşük okumalara neden olur. Bu durumda
gerçek kalem kuvveti spesifikasyonda belirtilenden daha yüksek olabilir. Bu özellikle üst kalem kuvveti
ayarı için geçerlidir.
(13) Bu ayarlamayı tamamlamak için NEXT tuşuna basın.
CE3000-UM-251-9370 7-5
7. ELECTRICAL ADJUSTMENTS
DISTANCE ADJUST
(6) Testi başlatmak için ENTER tuşuna basın. Çizici hemen test desenini çizer ve aşağıdaki menü görünür
DADJ.X= 0 Y= 0
X=400 mm
+X
Y=300 mm
(7) Kağıdı çıkarın ve X ve Y ekseni mesafesini ölçün. Yalnızca ana kartı değiştirdiyseniz,
kaydedilen değerleri kullanın.
(8) KONUM tuşlarını kullanarak değerleri girin.
Y ekseni veya X ekseni mesafe ayarını seçmek için SOL veya SAĞ OK tuşuna basın. Y ekseni
veya X ekseni mesafe ayar değerini değiştirmek için YUKARI veya AŞAĞI OK tuşuna basın.
Giriş değerinin formülü aşağıdaki gibidir:
X ekseni için giriş değeri = (400 mm - ölçülen X mesafesi) x 10
Y ekseni için giriş değeri = (300 mm - ölçülen Y mesafesi) x 10
Örneğin:
Y ekseni için 299,0 mm ölçtüyseniz ayar değeri olarak 10 girin.
Ayarlanabilir aralık: -9,9 mm ila +9,9 mm, 0,1 mm'lik adımlarla
(9) Ayarı kaydetmek için ENTER tuşuna basın. Aşağıdaki menü görünür.
XY LENG L=500.00
(10)Bu ayarlamayı tamamlamak istiyorsanız NEXT tuşuna basın. Ayarlanan test desenini çizmek istiyorsanız,
ENTER tuşuna basın.
CE3000-UM-251-9370 7-6
7. ELECTRICAL ADJUSTMENTS
7.7 6HUYR.D]DQFÕQÕQ*LULOPHVL
&(LoLQEXSURVHGUQX\JXODQPDVÕJHUHNOLGH÷LOGLU
$QDNDUWÕGH÷LúWLULUVHQL]ND\GHGLOHQD\DUGH÷HUOHULQLJLUPHNLoLQDúD÷ÕGDNLSURVHGUNXOODQÕQ
6HUYRND]DQFÕQDVÕOJLULOLU"
.DOHPWXWXFX\DPPoDSÕQGDELUNHVLFLNDOHPWDNÕQ
dL]LFL\HDúD÷ÕGDNLúHNLOGHJ|VWHULOGL÷LJLELELUNHVPHVD\IDVÕ\NOH\LQ
Kesim sacının ön ve arka uzunluklarının aynı uzunlukta olduğundan emin olun.
L1=L2
L2
L1
Cutting sheet
(3) TEST ve ENTER tuşlarına basarken gücü açın.(4) ROLL2 ortam modunu seçin.
(5) Aşağıda gösterilen menüyü görüntülemek için PAUSE tuşuna basın.
DISTANCE ADJUST
(6) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
SET GAIN
(7) Aşağıda gösterilen menüyü görüntülemek için ENTER tuşuna basın.
GAIN X= 80 Y= 50
(8) Şasiye kayıtlı değerleri girin. (varsayılan fabrika ayarları)
X-Kazanç değerini değiştirmek için YUKARI veya AŞAĞI OK tuşuna basın.
Y Kazanımı değerini değiştirmek için SOL veya SAĞ OK tuşuna basın.
(9) Ayarı kaydetmek ve ayarlamayı tamamlamak için ENTER tuşuna basın.
CE3000-UM-251-9370 7-7
7. ELECTRICAL ADJUSTMENTS
DISTANCE ADJUST
(4) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
MARK OPTION
(5) Aşağıda gösterilen menüyü görüntülemek için ENTER tuşuna basın.
DISTANCE ADJUST
(5) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
50
Bu seviye ölçer, işaret sensöründen gelen çıktıyı gösterir. Çıkış seviyesini %65'ten %70'e ayarlamak
için ana karttaki VR1'i ayarlayın. Bu ayarı yaparken medyanın kesme matı yüzeyinden yukarıya
çıkmadığından emin olun.
(7) Bu ayarlamayı tamamlamak için NEXT tuşuna basın.
CE3000-UM-251-9370 7-8
7. ELECTRICAL ADJUSTMENTS
DISTANCE ADJUST
(7) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
Media feed
direction
10 mm
10 mm
(10) Yazdırılan çarpı işaretini taramak için ENTER tuşuna basın. Çizici daha sonra aşağıdakilere dayalı olarak yeni bir
çarpı işareti çizer: Basılı çarpı işaretinin okunması.
Aşağıdaki menü görüntülenir.
X=00.0 Y=00.0
CE3000-UM-251-9370 7-9
7. ELECTRICAL ADJUSTMENTS
(11) Yazdırılan çarpı işareti ile çizilen çarpı işareti arasındaki uzaklığı ölçün.
Çizici tarafından Y
çizilen çapraz
işaret +X
+Y -Y
Medya
besleme
yönü
-X
X
(12) Ofset değerini ayarlayın. Numarayı değiştirmek için YUKARI OK tuşuna veya AŞAĞI OK tuşuna basın.
Bir sayının rakamlarını değiştirmek için SOL OK tuşuna veya SAĞ OK tuşuna basın.
X veya Y yönünü seçmek için ORIGIN tuşuna basın.
+ veya - yönünü seçmek için CONDSION tuşuna basın.
(13) Ayarı kaydetmek için ENTER tuşuna basın.
(14) Çizilen çarpı işareti çizgisinin, yazdırılan çarpı işareti çizgisinin merkezinde bulunduğunu doğrulayın. Taşı
yazdırılan çarpı işareti alanına kalemle dokunun. Adım (10)'da anlatıldığı gibi taramayı tekrarlamak için ENTER tuşuna basın.
CE3000-UM-251-9370 7-10
OTOMATİK KAYIT İŞARETİ HEDEFİ
7. ELECTRICAL ADJUSTMENTS
Çapraz işaretin özellikleri 30 mm çizgi uzunluğu ve 0,3 ila 0,5 mm çizgi genişliğidir.
X axis
7-11
CE3000-UM-251-9370
Y axis
7. ELECTRICAL ADJUSTMENTS
7.11 6LVWHPhUQ<D]ÕOÕPÕQÕ*QFHOOHPH
6LVWHPGRQDQÕP\D]ÕOÕPÕQÕJQFHOOHPHNLoLQDúD÷ÕGDNLGRV\DODUDVDKLSROPDQÕ]JHUHNLU$\UÕFDELU
ELOJLVD\DUYH&HQWURQLFVNDEORVXQXNXOODQPDQÕ]JHUHNLU
• CE3040.X :CE3000-40 firmware
• CE3060.X :CE3000-60 firmware
• CE3120.X :CE3000-120 firmware
• CE3120ap.X :CE3000-120AP firmware
• Pro.X :CE3000-40CRP firmware
• SEND.EXE :Utillity to transfer files using Windows®
• SENDB.EXE :Utillity to transfer files using DOS
1RW GDQVRQUDNLVLVWHPGRQDQÕP\D]ÕOÕPÕVUP&(0N&(0NYH&(0NLoLQNXOODQÕOÕU
&(0N6LVWHPGRQDQÕP\D]ÕOÕPÕQÕ]JQFHOOHQPHGL÷LQGH&(0NVLVWHPGRQDQÕP\D]ÕOÕPÕQÕJQFHOOH\HPH]VLQL]
oL]LFLQLQ GDQGDKDHVNLELUYHUVL\RQXGXU
6LVWHPGRQDQÕP\D]ÕOÕPÕQDVÕOJQFHOOHQLU
%LOJLVD\DUÕYH&( L&HQWURQLFVDUD\]DUDFÕOÕ÷Õ\ODED÷OD\ÕQ
6$ö2.NRQXPWXúXQDYH62/2.NRQXPWXúXQDEDVDUDNJFDoÕQ
DúD÷ÕGDJ|VWHULOHQPHQ\J|UQWOHPHNLoLQ.
PASSWORD
CENTRO GET-ACK
Bu, Centronics arayüzünün zamanlamasını seçmenizi sağlar.
Normalde bu ayarı değiştirmenize gerek yoktur. Verileri Centronics arayüzü aracılığıyla doğru bir
şekilde aktaramıyorsanız, bu zamanlamayı değiştirmek için YUKARI OK (+X) konum tuşunu veya
AŞAĞI OK (-X) konum tuşunu kullanın.
(4) Aşağıda gösterilen menüyü görüntülemek için ENTER tuşuna basın.
**KB RECEIVED
(7) Çizici, tüm veriler alındığında başlatma rutinini başlatacaktır. Firmware sürümü
Başlatma rutini sırasında görüntülenir. Güncellediğiniz ürün yazılımı sürümünü kontrol
edin.(8) Gücü kapatın.
CE3000-UM-251-9370 7-12
7. ELECTRICAL ADJUSTMENTS
CE3000-UM-251-9370 7-13
7. ELECTRICAL ADJUSTMENTS
DISTANCE ADJUST
(5) Aşağıda gösterilen menü görüntülenene kadar PREV tuşuna basın.
Pensel POS
(6) Aşağıda gösterilen menüyü görüntülemek için ENTER tuşuna basın.
Pensel POS 0
(7) SAĞ OK tuşuna basın; 2. kalem tutucu 2. kalem istasyonuna taşınır.
Kalemler değiştirilirken 2. kalemlik gelene kadar SOL OK tuşuna basmaya devam edin.
değişim konumunda durur.
(8) 2. kalem tutucu ile 2. kalem istasyonu arasındaki boşluğu ölçün.
1 mm
CE3000-UM-251-9370 7-14
7. ELECTRICAL ADJUSTMENTS
DISTANCE ADJUST
(5) Aşağıda gösterilen menü görüntülenene kadar PREV tuşuna basın.
DPOS= 0 SH=+80
(7) Yalnızca ana kartı değiştirdiyseniz kasaya kayıtlı değerleri girin. (varsayılan fabrika ayarları)
CE3000-UM-251-9370 7-15
7. ELECTRICAL ADJUSTMENTS
1 PEN 12 30 2
(6) Tekrar COND tuşuna basın ve ardından durum 2 ayar menüsünü seçmek için YUKARI OK tuşuna basın.
Koşul 2'yi aşağıda gösterildiği gibi ayarlayın ve ardından ayarı kaydetmek için ENTER tuşuna basın.
2 PEN 12 30 2
(7) Aşağıda gösterilen menüyü görüntülemek için DURAKLAT tuşuna basın.
DISTANCE ADJUST
(8)Aşağıda gösterilen menü görüntülenene kadar PREV tuşuna basın.
X= 0 Y= 0
(13) Kalem 1 çarpı işareti ile kalem 2 çarpı işareti arasındaki uzaklığı ölçün.
Cross mark Y
plotted by
pen 1 +X
+Y -Y
Media feed
direction
-X
X
CE3000-UM-251-9370 7-16
7. ELECTRICAL ADJUSTMENTS
(14) Ofset değerini ayarlayın. Sayıyı temel alarak değiştirmek için YUKARI OK tuşuna veya AŞAĞI OK tuşuna basın.
kalem 2 çarpı işareti.
X veya Y yönünü seçmek için SAĞ OK tuşuna veya SOL OK tuşuna basın.
(15) Çizilen kalem 1 çarpı işareti çizgisinin, çizilen kalem 2 çarpı işareti çizgisinin merkezinde bulunduğunu doğrulayın.
(16) Çizilen çarpı işaretleri yanlış konumlandırılmışsa (8) ila (15) arasındaki adımları tekrarlayın. Çizilen artı işaretleri
doğru konumlardaysa, ayarı kaydetmek ve ayarlamayı tamamlamak için ENTER tuşuna basın.
CE3000-UM-251-9370 7-17
8. SERVICE MODES
8 SERVİS MODLARI
8.1 Sensör Test Modu
Bu mod sensör durumunu kontrol eder. Arızalı bir sensör varsa aşağıdaki tabloda yer alan belirtilerden
birini gözlemleyeceksiniz.
Lütfen ilgili sensörleri kontrol edin.
Sensor Symptom
Y home sensor Kalem bloğu sağ taraftaki plakaya çarpıyor.
Cam sensor Çizicide “MEDYA YÜKLE!” mesajı görüntülenir. medya zaten yüklendiğinde.
Push roller sensor Kalem bloğu sol taraftaki plakaya çarpıyor.
+X, -X media sensor Medya çiziciden çıkar.
Sensörler nasıl test edilir
(1) Çiziciye A4 (Letter) veya daha büyük boyutta bir kağıt yükleyin.
(2) TEST ve ENTER tuşlarına basarak gücü açın.
(3) Ortam modunu seçin.
(4) Aşağıda gösterilen menüyü görüntülemek için DURAKLAT tuşuna basın.
DISTANCE ADJUST
(5) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
SENSOR TEST
(6) Aşağıda gösterilen durumu görüntülemek için ENTER tuşuna basın.
YH CH PH +XH -XH
Y: Y ana sensör, C: Kam sensörü, P: İtme silindiri sensörü, +X: +X medya sensörü, -X: -X medya sensörü
(7) Ön medya sensörünü bir kağıt parçasıyla örtün.
+X'in durumu “L”den “H”ye değişir.
(8) Arka medya sensörünü bir parça kağıtla örtün.
-X'in durumu “L”den “H”ye değişir.
(9) Kalem bloğunu en sağa hareket ettirin. Kalem bloğu ana konum bayrağına ulaştığında Y'nin durumu
"L"den "H"ye değişir.
(9) İtme silindirlerini kaldırmak için medya ayarlama kolunu indirin. C'nin durumu “L”den “H”ye değişir.
(10) Kalem bloğunu sola ve sağa hareket ettirin. Kalem bloğu itme silindirini geçtiğinde P'nin durumu
"L"den "H"ye değişir.
CE3000-UM-251-9370 8-1
8. SERVICE MODES
DISTANCE ADJUST
(5) Aşağıdaki menü görüntülenene kadar NEXT tuşuna basın.
TEST KEY
(6)Aşağıda gösterilen durumu görüntülemek için ENTER tuşuna basın.
00 0000 0000
(7) Kontrol panelindeki her tuşa basın; durum “0”dan “1”e değişecektir.
Her rakamın durumu:
Key Digit
NEXT 1st digit
PREV. 2nd digit
ORIGIN 3rd digit
TEST 4th digit
COND 5th digit
ENTER 6th digit
DOWN ARROW 7th digit
UP ARROW 8th digit
RIGHT ARROW 9th digit
LEFT ARROW 10 th digit
PAUSE DURUM Lambası (DURAKLAT tuşuna basıldığında ancak yalnızca ilk kez
basıldığında yanar)
CE3000-UM-251-9370 8-2
9. TROUBLESHOOTING
9. SORUN GİDERME
9.1 Çizici Açık Ama Çalışmıyor
Belirti Doğrulama öğesi Çözüm
Kontrol panelinin LED (1) Çiziciye güç sağlanıyor mu? Hayır .....Güç kablosunun çizicinin AC
hat girişine güvenli bir şekilde
lambası yanmıyor veya
bağlandığını kontrol edin.
LCD'de hiçbir şey
görüntülenmiyor. Evet .... (2) numaralı öğeyi doğrulayın.
(2) FPC270102 esnek kablo ana Hayır .....Esnek kabloyu güvenli
karta ve kontrol paneline güvenli bir bir şekilde bağlayın.
şekilde bağlanmış mı?
Evet .... (3) numaralı öğeyi doğrulayın.
(3) FPC270102 esnek kablo bozuk Hayır .....Öğeyi (4) doğrulayın.
mu?
Evet ....FPC270102 esnek kabloyu
değiştirin
(4) AC hattı elektrik çıkışı doğru mu? Hayır .....AC hattını değiştirin.
Evet .... (5) öğesini doğrulayın.
(5) Güç kaynağı ünitesinde 24 V Hayır .....Güç kaynağı ünitesini değiştirin.
çıkış var mı?
Evet ....Ana kartı değiştirin.
CE3000-UM-251-9370 9-1
9. TROUBLESHOOTING
Çizici ortam boyutunun (1) Ön medya sensöründe ve arka Yes ....Clean the front media sensor and
medya sensöründe toz var mı?
X yönünü tanıyamıyor. the rear media sensor.
No .....Verify item (2).
(2) Ön medya sensörü ve arka No .....Connect the cables securely.
medya sensörü kabloları her bir
Yes ....Replace the sensor(s).
konnektöre güvenli bir şekilde
bağlanmış mı?
Medya açılı olarak (1) Are the push rollers worn down? Yes ....Replace the push roller(s).
beslenir. No .....Verify item (2).
(2) Is there anything on the drive Yes ....Clean the drive roller with a brush.
roller? No .....Verify item (3).
(3) Do the push rollers have the No .....Replace the push roller spring(s).
correct pressure? Yes ....Verify item (4).
(4) Is the drive roller worn down? Yes ....Replace the drive roller.
No .....Verify item (5).
(5) Is the drive roller attached Yes ....Replace the bearing of the drive
correctly? roller.
No .....Attach the drive roller correctly.
CE3000-UM-251-9370 9-2
9. TROUBLESHOOTING
CE3000-UM-251-9370 9-3
10. PARTS LIST
CE3000-UM-251-9370 10-1
10. PARTS LIST
Outer Casing
18
21
22 23 20
19
CE3000-UM-251-9370 10-2
10. PARTS LIST
CE3000-UM-251-9370 10-3
10. PARTS LIST
CE3000-UM-251-9370 10-4
10. PARTS LIST
CE3000-UM-251-9370 10-5
10. PARTS LIST
CE3000-UM-251-9370 10-6
10. PARTS LIST
Pen Block
32 41 43
40
35 40
27 36 35 42
33
36
12 37
34 38
Pen Holder CE3000-120AP 38
37 39
Pen Station
CE3000-120AP
CE3000-UM-251-9370 10-7
10. PARTS LIST
CE3000-UM-251-9370 10-8
10. PARTS LIST
Stand CE3000-120
No. Part No. Description Q’ty Remarks
1 621231031 Right Side Stay 120 1 CE3000-120
2 621231041 Right Foot 120 1 CE3000-120
3 621231020 Right Top Plate 120 1 CE3000-120
4 621231071 Left Side Stay 120 1 CE3000-120
5 621231081 Left Foot 120 1 CE3000-120
6 621231060 Left Top Plate 120 1 CE3000-120
7 621151130 Center Bar 120 1 CE3000-120
8 621231093 Stock Shaft 120 2 CE3000-120
9 621231093 Stock Shaft 120
10 621231121 Stopper 120 2 CE3000-120
11 305811005 Hexagonal wrench (M5) 1
12 301001020 Hexagonal wrench (M6) 1 CE3000-120
13 391650100 Hexagonal bolts (M5M5L10Ni) 12
14 391660200 Hexagonal bolts (M6L20Ni) 8 CE3000-120
Stand CE3000-120
CE3000-UM-251-9370 10-9
10. PARTS LIST
Stand CE3000-120AP
No. Part No. Description Q’ty Remarks
1 621231370 Left Side Stay 120AP 1 CE3000-120AP
2 621231380 Right Side Stay 120AP 1 CE3000-120AP
3 621151130 Center Bar 120 1 CE3000-120
4 621231170 Left Foot 120AP 1 CE3000-120AP
5 621231180 Right Foot 120AP 1 CE3000-120AP
6 621159730 BS Rear Pipe 120 2 CE3000-120/120AP
7 621159710 BS Bracket 120 2 CE3000-120/120AP
8 621161250 Stock Shaft 120AP 1 CE3000-120AP
9 619052391 2/3 Inch Stopper 2 CE3000-120AP
10 391906151 Coin Screw M6L15 1 CE3000-120AP
11 621259011 Stopper 120AP 1 CE3000-120AP
12 391440068 M4L6 Set Screw 2 CE3000-120AP
13 M4L6 Cap Screw 1 CE3000-120AP
14 621231113 Alignment Shaft Cap 2 CE3000-120AP
15 621252251 Alignment Shaft Holder AP 2 CE3000-120AP
16 621231103 Shaft 120 1 CE3000-120AP
17 621251030 Right 120AP Holder Plate 1 CE3000-120AP
18 621161132 100AP Shaft Holder 1 CE3000-120AP
19 621259050 AP Stopper Base 1 CE3000-120AP
20 392040180 Bush D4L18 2 CE3000-120AP
21 380101981 Spring, C-198 1 CE3000-120AP
22 621259070 AP Stopper Arm 1 CE3000-120AP
23 621251020 Left 120AP Holder Plate 1 CE3000-120AP
24 310063620 Bearing 636ZZ 2 CE3000-120AP
25 M6L16 Cap Screw 2
26 Washer C6 D11.5 2
27 M4L14 Binding Head Screw 4
28 M4L25 Binding Head Screw 2
29 M3L30 Binding Head Screw 1
30 M3 Nut 1
31 Washer C3 D8 1
32 M4L6 Binding Head Screw 2
33 M4L8 Binding Head Screw 4
621161040 Basket 100AP 1 CE3000-120AP
305811005 Hexagonal wrench (M5) 1
301001020 Hexagonal wrench (M6) 1
391650100 Hexagonal bolts (M5M5L10Ni) 12
391660200 Hexagonal bolts (M6L20Ni) 8
CE3000-UM-251-9370 10-10
10. PARTS LIST
Stand CE3000-120AP
17
23
27
26 27
33
24 22 19
32
25 18 28
30
9 29
31 21 20
9 16
6 15
8 14
6
10
1 2
3
4
5
11
12
13
CE3000-UM-251-9370 10-11
10. PARTS LIST
4
1
5
3 2
CE3000-UM-251-9370 10-12
���������
���������
�����������
����������
���������
����
���������
��������� ����
����
���������
CE3000-UM-251-9370
������� ��������� ���� ����
���������
����������� ����
���� ����
���������
11.1 Block Diagrams
���������
��������� �����������
����
���
��������� ��������
�������� �����
���
����� �����
���
��������� ���
SW1
��������� ����������
���
11.1.1 Block Diagram for CE3000-120
��������� ��
�� �� ��������� ���������
��������
11-1
JWA2120-0033 ����
�� ���
��������
���������
��
��
���������
���������
�������
���
���
��������
�����
��� ��� ��� ���
�����
������� ��� ����������
�����
�������
���������
����� ���������
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
��������������� ���������������
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
���������
���������
���������� �����������
���������
����
���������
��������� ����
����
CE3000-UM-251-9370
���������
���
����������� ����
����
���� ���������
���������
��������� ����
��������� ����
��������
���������
�����������
����
���
���
���
SW1
��������� ����������
���
�������� ��
�� �� ��������� ���������
11.1.2 Block Diagram for CE3000-60
��������
JWA2120-0033 ����
�� ���
��������
11-2
��
��
���������
���������
���
���
�������
��� ��� ��� ���
�������
���������
��������������� ���������������
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
���������
���������
���������� �����������
���������
����
���������
��������� ����
����
CE3000-UM-251-9370
���������
���
����������� ����
����
���� ���������
���������
��������� ����
��������� ����
��������
���������
�����������
����
���
���
���
SW1
��������� ����������
���
�������� ��
��� ��� ��������� ���������
11.1.3 Block Diagram for CE3000-40
��������
JWA2120-0033 ����
�� ���
11-3
��������
��
��
���������
�������
���������
���
���������
��������������� ���������������
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
CPU GRC1507
D[0..15] A[0..21] CENCSZ
D[0..15] A[0..21] AP[18..21] A[0..21] CENCSZ
AP[18..21] AP[18..21] USBCSZ
LOCALINTZ AB-ENZ AB-ENZ USBCSZ NVRAMCSZ
SRVINTZ LOCALINTZ RDZ RDZ NVRAMCSZ IOCS1Z
USBINTZ SRVOINTZ WRHZ IOCS1Z
CINTZ USBINTZ WRLZ WRLZ
CINTOUTZ RDWR
DCDRIVER
RASZ
CASLZ
CASHZ XCOMA XCOMA DCMC+
TOMBO XCOMB XCOMB DCMC-
CS0Z YCOMA YCOMA
EPROMDOUT CS1Z CS1Z YCOMB YCOMB
CS2Z CS2Z PNCOMA PCOMA
CE3000-UM-251-9370
FEEDER PNCOMB PCOMB
FEEDER-O DTR-DZ LOCALZ SFRZ SFRZ
RTS-DZ CINTINZ
CTS0Z SFREE SRVINTZ
RXD0 SRVINTZ FANON
TXD0 CINTZ
FEEDER1 DSR0 PNENA CINTOUTZ
FEEDER1-O PNENB DCDRIVER
RS LOCALLED
RW LOCALINTZ
E RESET LOCALINTZ
LCDB[0..7] RESET
11.2 Circuit Diagrams
RESET
RESET RESETZ D[0..15]
RESETZ
GRC1507
CPU
MEMORY
D[0..15] FR_BUSYZ
A[0..21] EPROMOUT
RASZ
CASLZ
CASHZ
RDWR
RDZ
11-4
WRLZ
IF NVRAMCSZ CS0Z
NVRAMCSZ
D[0..15] DTR-DZ RESETZ
A[0..21] RTS-DZ RESETZ
11.2.1 Main Board Top Section (PR270101A)
CENCSZ CTS0Z
CENCSZ RXD0
RDZ TXD0
WRLZ DSR0Z MEMORY
CENINT
PB[0..7]
PB[0..7]
RESET FEEDER1
RESET FEEDER1-O
IF CONNECT
D[0..15] LOCALZ
IOCS1Z PENA
IOCS1Z PENB
USB FANON
USBINTZ MC+ SFREE
D[0..15] USBINTZ MC- TOMBO
A[0..21]
PB[0..7] FEEDER
USBCSZ FEEDER-O
USBCSZ LOCALLED
WRLZ FR_BUSYZ
RDZ
RESETZ RS
RESETZ RW
LCDB[0..7] E
LCDB[0..7]
USB
CONNECT
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
RA2 RA3
10K*4 10K*4 U1A R1 470 2012
VCC 1 2 74LS06 VCC
LOCALLED
30FLT-SM1-TB(0.5mm Pitch)
FL1
N2012Z121T03 J1
LOCALZ
PB[0..7] 1 GND
2 KEY0
3 KEY1
PB0 FL2 KCONT0 4
PB1 EXCCET102U D1 1SS352-TPH3 KEY2
5 KEY3
PB2 FL3 KCONT1 6
PB3 EXCCET102U D2 1SS352-TPH3 GND
7 CAM_ANO
PB4 FL4 KCONT2 8
PB5 SFREE CAM
EXCCET102U D3 1SS352-TPH3 9
PB6 FEEDER-O PAUSEZ
FL5 10
PB7 FANON PAUSELED
EXCCET102U 11
FL6 KCONT2 GND
12 KCONT2
KCONT0
CE3000-UM-251-9370
RA4 RA5 EXCCET102U 13
VCC 10K*4 10K*4 FL7 KCONT1 KCONT0
14 KCONT1
EXCCET102U 15
FL8 VCC
16 VCC
EXCCET102U 17 VCC
D[0..15] A6S-4101(OMRON) 18 LCD_CNT
D0 2 18 FL9 19
D1 A0 B0 SW1 EXCCET102U LCDB0(RS)
3 A1 B1 17 20 LCDB1(R/W)
D2 4 16 FL10 21
D3 A2 B2 EXCCET102U LCDB2(E)
5 A3 B3 15 22 LCDB0
D4 6 14 FL11 23
D5 A4 B4 EXCCET102U LCDB1
7 A5 B5 13 24 LCDB2
D6 8 12 FL12 25
D7 A6 B6 EXCCET102U LCDB3
9 A7 B7 11 FR_BUSYZ 26 LCDB4
FL13 27
EXCCET102U LCDB5
1 DIR 28 LCDB6
19 FL14 29
IOCS1Z OE LCDB7
1SS352-TPH3 EXCCET102U 30
74HC245/SO FL15 GND
U3 RA6 RA7 RA43 D4 EXCCET102U C112
VCC 10K*4 10K*4 10K*4 D7 FL28 104
EXCCET102U
D5 D6 FL29
EXCCET102U C111
FL30 47uF/16V
EXCCET102U
RS
FL31
RW
EXCCET102U
E LCDB0
LCDB1 VCC VCC
LCDB2
LCDB3
05FMN-SMT-A-TF VCC
LCDB4 R95 R4 R5
LCDB5 470 2012 8.2K 200 R94
LCDB6 J21 470 2012
LCDB7 5 R93
ANODE VCC 470 2012
LCDB[0..7] 4 GND
3 CAM
C2 J6
2 VCC
101 1 1
11-5
OPEN PENA PENA
PENB 2 PENB
C1 3
101 GND
4 YHOME
5 PINCH
6 YH-ANO
7 PI-ANO
U1E R106 200 2012
8 TOMBO
11 10 9 TOMBO-ANO
10 VCC
74LS06 11 GND
MC+ 12 MCP
13 MCP
VCC C3 14
MC- MCM
FL16 104 15 MCM
16 GND(FG)
C4
N2012Z121T03 220uF/50V
+24V VR1 C116 16FMN-BMT-A-TF
104
U5 SI-8050 ST-7TA 10K
4 U51A TP1
8
FB R100 10K NJM3404AM U51B
8
L1 SLF12575-151M1R5 VCC
HK-1-S
1 Vin 3 +
C5 2 1 5 +
Vout
2 - 7 TOMBO
220uF/50V D8 R103 6 -
GND
ON
C6 C113 10K
SFPW-56
4
NJM3404AM
3
5
4
1000uF/10V 472
11.2.2 Main Board Connector Block Section (PR270101A)
R104
R105 100K
R101 10K
R102 150K
10K
J22
+24V LGP3131-0110
J2 VCC
1
2
3 C110
4
B4P-VH 47uF/16V
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
22K*4 22K*4 22K*4 22K*4 22K*4
Y1 XPEEEC6.00MHz VCC RA8 RA9 RA10 RA11 RA12
C104 R97 0
AP[18..21]
18
R96
R * U6
C105 72 32 AP21
XTAL PB9/IRQ7/A21 AP20
A13
A12
A11
A10
A17
A16
A15
A14
A1
A0
A5
A4
A3
A2
A9
A8
A7
A6
PB8/IRQ6/A20/WAIT 31
18 74 30 AP19
EXTAL PB7/A19 AP18
PB6/A18 29 A[0..21]
VCC 22 A17
A17 A16
73 MD3 A16 20
75 19 A15
MD2 A15 A14
78 MD1 A14 18
79 17 A13
MD0 A13 A12
A12 16
84 15 A11
RES A11 A10
14
CE3000-UM-251-9370
A10 A9
76 NMI A9 13
12 A8
A8 A7
A7 11
VCC 10 A6
A6 A5
A5 9
RA15 R9 8 A4
A4 A3
10K*4 10K 7
A3 A2
VCC 6
U7 A2 A1
A1 5
3 1 4 A0
Vcc VOUT A0
C7 99 PF7/AN7 D15
U1C U1D 98 PF6/AN6 D15 52
104 4 2 5 6 9 8 97 53 D14
GND M.R RESETZ AVSS D14
96 54 D13
PF5/AN5 D13 D12
PST592DMT 74LS06 74LS06 95 56
PF4/AN4 D12 D11
94 PF3/AN3 D11 57
93 58 D10
PF2/AN2 D10 D9
RESET VCC 92 59 10K*4 10K*4 10K*4 10K*4
PF1/AN1 D9 D8
RA21 91 60 VCC RA22 RA23 RA24 RA25
PF0/AN0 D8 D7
10K*4 100 62
AVCC D7 D6
D6 63
64 D5
D5 D4
LOCALINTZ 49 PA2/SCK0/DREQ0/IRQ0 D4 66
46 67 D3
SRVOINTZ PA5/SCK1/DREQ1/IRQ1 D3
43 68 D2
CINTOUTZ PA8/TCLKCC/IRQ2 D2 D1
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
42
D10
D11
D12
D13
D14
D15
USBINTZ PA9/TCLKCD/IRQ3 D1 69
70 D0
D0
D[0..15]
PB2/IRQO/RAS 24 RASZ
PB3/IRQ1/CASL 25 CASLZ
PB4/IRQ2/CASH 26 CASHZ
PB5/IRQ3/RDWR 28 RDWR
WRL 38 WRLZ
36
11-6
R11 WRH WRHZ
1K 34 RDZ
RD
TOMBO
CS0 41 CS0Z
CS1 40 CS1Z
C8 45 CS2Z VCC +24V
PA6/TCLKA/CS2
PA7/TCLKB/CS3 44
104
PA15/CK 83
R99
51 RXD0 10K J23 B7B-PH-KS
PA0/RXD0
PA1/TXD0 50 TXD0
R12 200 1
PE0/TIOC0A/DREQ0 85
2
80 PLLVcc PE1/TIOC0B/DRAK0 86 EPROMDOUT FEEDER-O 3
81 PLLCAP PE2/TIOC0C/DREQ1 87 RTS-DZ FEEDER1-O
VCC C9 4
82 PLLVss PE3/TIOC0D/DRAK1 88 DTR-DZ
104 5
6
48
11.2.3 Main Board CPU Block Section (PR270101A)
PA3/RXD1 CTS0Z 7
C11 C12 C13 C14 C16 C17 47
PA4/TXD1 DSR0
104 104 104 104 104 104 89
R13 3K PE4/TIOC1A AB-ENZ
C10 470 PE5/TIOC1B 102 RS
Vcc
Vcc
Vcc
Vcc
Vcc
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
90
101
109
61
71
39
55
3
23
27
33
77
103
21
37
65
VCC
104
C25
C15 104
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
QA1 L6203
7 C26 R14
XCOMB IN2 153 39_1W
BOOT1 4
SFRZ 11
SFRZ ENA
OUT2 1
10 SNS C27 C28 J7
9 8 153 152
VREF BOOT2 1
2
VS
GND
C29 B2B-XH-A
224
2
6
C30
CE3000-UM-251-9370
+24V 103/50V
C31
220uF/50V
QA2 L6203
7 C32 R15
YCOMB IN2 153
4 39_1W
SFRZ BOOT1
11 ENA
OUT2 1
10 SNS C33 C34 J8
9 8 153 152
VREF BOOT2 1
C35 2
224 3
VS
GND
B3B-XH-A
2
6
C36
103/50V
+24V
C37
11-7
220uF/50V
QA3 L6203
7 C38 R16
PCOMB IN2 153 39_1W
BOOT1 4
SFRZ 11 ENA DCMC+
OUT2 1
10 SNS C39 C40
9 8 153 152
VREF BOOT2 DCMC-
C41
224
11.2.4 Main Board Motor Drive Section (PR270101A)
VS
GND
2
6
C42
103/50V
+24V
C43
220uF/50V
VCC +24V
J9
R17 R18 1
470 2012 470 2012 2
U1B B2B-EH-A
3 4 74LS06 Q1
FANON 2SD1286-Z
R19 1K
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
22K*4
VCC RA13 VCC
FL18 FL19
GA-VCC GA-GND
EXCCET103U
1 2 3 4 C44 N2012Z121T03
104
A20
A21
A19
A18
C45
A[0..21] RESET 104
AP[18..21]
C46
U50 102
65
79
90
3
28
53
78
4
15
29
40
54
U11
CE3000-UM-251-9370
AP21 2 4 A21
AP20 1A 1Y A20 WRLZ
5 7
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
AP19 2A 2Y A19
11 3A 3Y 9 92 SYSRST
AP18 14 12 A18 35
4A 4Y SRAMCS*
VCC A21 31 36
HA<2> KROMCS*
3 A20 32 37 U49A
1B HA<1> FDDCS*
R98 6 A19 33 38 CENCSZ 1
2B HA<0> CENCS*
10K 10 A5 23 39 USBCSZ 3 NVRAMCSZ
3B A<5> PENCS*
13 A4 24 41 2
4B A<4> NVRAMCS*
A3 25 42
A<3> IOCS1*
AB-ENZ 1 A2 26 43 74HC32
SEL A<2> IOCS2*
15 A1 27 44 U49B
EN A<1> OFFCS*
D[0..15] PSADCS* 56 4
S=L:A D11 9 69 6 IOCS1Z
74HC157/SO D<11> XDAL* RDZ
D10 10 70 5
S=H:B D<10> YDAL*
D9 11 D<9>
D8 12 73 SRVINTZ 74HC32
D<8> SRVINT*
D7 13 74 LOCALINTZ
D<7> LOCALINT*
D6 14 75
D<6> VIEWINT*
D5 16 76
D<5> HISPINT*
D4 17 77 CINTOUTZ
D<4> CINTOUT*
VCC D3 18 D<3>
D2 19 51
D<2> SDADIN
D1 20 52
D<1> SDACLK
RA26 D0 21 57
D<0> SDALD
VCC 470*4
1 2 3 4 RDZ RDZ 47 62 XCOMA
WRLZ RD* XCOMA
VCC WRLZ 46 63 XCOMB
C47 104 WR* XCOMB
J10 64 YCOMA
YCOMA
CS1Z 22 CS4* YCOMB 66 YCOMB
1 EXCCET102U CS2Z 34 CS6* PNCOMA 67 PNCOMA
2
FL21 PNCOMB 68 PNCOMB
3
49 PENSD
4
FL22 50 1
14
7
SAMP HISINLED
B4B-XH-A EXCCET102U 5
CARLED
11-8
1 1A 1Y 3 93 XENA YLED 55
4 6 94 80
VCC
LOCALLED
GND
J11 2A 2Y XENB LOCALLED
10 3A 3Y 8 95 YENA 81
HISPLED
EXCCET102U 13 4A 4Y 11 96 83
1 YENB CHALED2
FL24 97 84
2 PNENA CHALED1
3 2 C1 98 PNENB PENLED13 99
4 5 C2 100
PENLED24
5 9 C3 LOCALZ 86 LOCALKEY*
12 VCC GA-VCC 87 2
B5B-XH-A FL25 C4 VIEWKEY* ADTRG*
88 HISPKEY* WAIT* 45
EXCCET102U 89 61 SFRZ
U12 CHARTKEY* OUTDIS*
R20 82
SN75189APW 2K CHARTHOLD
58 TSNS2*
59 TSNS1*
C48 C49 C50 C51 60
102 102 102 102 SFREE SFREE
CINTINZ 72 CINTIN
11.2.5 Main Board GRC 1507 Section (PR270101A)
85 CHARTTIMER
VCC C109 6
TSTIN
100 30 CPUCLK TSTIN2 7
VCC 91 CLKIN TSTIN3 8
C52
RA27
470*4 1 2 3 4 GA-GND
GRC1507
104
GA-GND
U14B TC7WU04F
14
7
U14A
PNENA 1 3 3 5 1 7
1A 1Y
PNENB 4 6
VCC
GND
2A 2Y R21 2.4K TC7WU04F
10 3A 3Y 8
13 4A 4Y 11
2 C1
5 Y2
C2 XPCEEC50.0MHz
9 C3
12 C4
C106 C107
U13 8 8
SN75189APW
C53 C54
102 102
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
VCC
D[0..15] 10K*4
RA30 RA31
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
1 2 3 4 1 2 3 4 10K*4
24
39
17
2
U16 DATA[7..0]
D0 32 43 2 18 DATA0
D1 D0 PA0 A1 B1 DATA1
31 42 3 17 J12
VCC
VCC
VCC
GND
D2 D1 PA1 A2 B2 DATA2 DATA7
30 41 4 16 9
CE3000-UM-251-9370
D3 D2 PA2 A3 B3 DATA3 D7
A[0..21] 29 40 5 15 DATA6 8
D4 D3 PA3 A4 B4 DATA4 D6
28 38 6 14 DATA5 7
D5 D4 PA4 A5 B5 DATA5 D5
27 37 7 13 DATA4 6
D6 D5 PA5 A6 B6 DATA6 D4
26 36 8 12 DATA3 5
D7 D6 PA6 A7 B7 DATA7 D3
25 35 9 11 DATA2 4
D7 PA7 A8 B8 D2
DATA1 3
A2 PB0 D1
4 14 19 DATA0 2
A3 A0 PB0 PB1 G JP8 D0
3 A1 PB1 15 1 18 +5V
PB2 DIR DSP03-003-432 B
PB2 16 STB 13 SLC
44 18 PB3 74LS245 A U18B 10
RDZ RD PB3 ACK
34 19 PB4 C 2 1 4 3 1
WRLZ WR PB4 STB
1 20 PB5 11
CENCSZ CS PB5 BUSY
33 21 PB6 U18A 32
RESET RESET PB6 74LS14/SO 74LS14/SO ERROR
23 PB7 14
PB7 OPEN
PB[0..7] 15 OPEN
9 12 GND
PC0
10 16 GND
PC1
11 FEEDER1-O 17 GND
PC2 JP9
13 CENINT 19 GND
PC3 U18E 74LS14/SO DSP03-003-432
8 U18D 20
PC4 B GND
7 9 8 11 10 21 GND
PC5 A
6 22 GND
PC6 74LS14/SO C
5 23 GND
PC7
BUSY U18F 24 GND
13 12 25 GND
U2 26
MSM82C55A-2GS-2K GND
VCC 74LS14/SO 27 GND
U18C 28 GND
5 6 29 GND
30 GND
RA44 8 7 6 5 74LS14/SO 31 N.C.
10K*4 VCC 33 GND
RA32
VCC 10K*4 FRC685J036-L/Y
8 7 6 5
11-9
J20 8 7 6 5
1 RA33 RA34 VCC
VCC
2 +XSNS 1K*4 1K*4
3 GND
4 VCC
5 -XSNS
6 GND
VCC B6B-PH-K
C92
9
11.2.6 Main Board Interface Section (PR270101A)
U20
224
10 C1+ V+ 11
Vcc
C57
224
C56 12 15
C1- V-
13 C93
104 C58 C2+
224
R26 VCC
224 14 R27 1K
C2- R28 1K
1K J14
TXD0 5 T1 IN T1 OUT 2 4 RTS
RTS-DZ 18 T2 IN T2 OUT 1 20 DTR
DTR-DZ 19 T3 IN T3 OUT 24 2 TXD
21 T4 IN T4 OUT 20 3 RXD
5 CTS
RXD0 6 R1 OUT R1 IN 7 6 DSR
CTS0Z 4 R2 OUT R2 IN 3 9 +5V
DSR0Z 22 R3 OUT R3 IN 23 1 SHILED
17 R4 OUT R4 IN 16 7 GND
JP12 B
A
GND
C R29 FCN675J025-L/C#U
SP208ECA SSOP
1K
8
DSP03-003-432
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
D[0..15]
37
27
46
A[0..21]
A[0..21] A1 D0
25 A0 DQ0 29
A2 24 31 D1
VSS
VSS
VCC
A3 A1 DQ1 D2
23 A2 DQ2 33
A4 22 35 D3
A5 A3 DQ3 D4
21 A4 DQ4 38
A6 20 40 D5
A7 A5 DQ5 D6
19 42
CE3000-UM-251-9370
A8 A6 DQ6 D7
18 A7 DQ7 44
A9 8 30 D8 VCC
A10 A8 DQ8 D9
7 32 J19
A9 DQ9 D10
A11 6 34
A12 A10 DQ10 D11 1
5 A11 DQ11 36 2
A13 4 39 D12
A14 A12 DQ12 D13 3
3 A13 DQ13 41 4
A15 2 43 D14
A16 A14 DQ14 D15 A1 5
1 A15 DQ15/A-1 45 6
A17 48 A2
A18 A16 A3 7
A20
VCC 17
A19 A17 A4 8
16 A18 9
15 A5
RY/BY FR_BUSYZ 10
26 A6
CE A7 11
RDZ 28 OE 12
11 A8
WRLZ WE 13
47 A9
RESETZ BYTE A10 14
RESETZ 12 RESET 15
A11
A12 16
U22 MBM29F800BA-70PFTN A13 17
U49C
A14 18
CS0Z 9 19
8 A15
U14C TC7WU04F A16 20
10 21
A17
A18 22
6 2 74HC32
A19 23
24
U49D
25
JP20 12
DEBUGZ 26
DSP03-003-432 11
C63 27
13 VCC
D0 28
D1 29
74HC32 10uF/16V
D2 30
C64 104 D3 31
32
11-10
D4
D5 33
D6 34
D7 35
D8 36
D9 37
42
21
1
37
22
D10 38
D0 D11 39
A1 17 2
A0 DQ0 D1 D12 40
A2 18 3
VSS
VSS
VSS
VCC
VCC
VCC
A1 DQ1 D2 D13 41
A3 19 4
A2 DQ2 D3 D14 42
A4 20 5
A3 DQ3 D4 D15 43
A5 23 7
A4 DQ4 D5 DEBUGZ 44
A6 24 8
A5 DQ5 D6 45
A7 25 9
A6 DQ6 D7 46
A8 26 10
A7 DQ7 D8 47
A9 27 33
A10 A8 DQ8 D9 48
28 A9 DQ9 34 49
16 35 D10
NC DQ10 D11 50
15 NC DQ11 36
VCC 38 D12 8911-050-178S-A
C62 104 DQ12 D13
RASZ 14 RAS DQ13 39
CASHZ 30 40 D14
11.2.7 Main Board Memory Block Section (PR270101A)
RDWR 13 WE
RDZ 29 OE
U23
2
7
U24
D0 3 2 5 DI 6
D1 Q1 DO U27
D1 4 5
VCC
GND
D2 D2 Q2 M5M418160CJ-6S
7 6 3 CS
D3 D3 Q3 1
8 9 4 SK NC
D4 D4 Q4 8
13 D5 Q5 12 NC
D5 14 15
D6 D6 Q6
17 D7 Q7 16 BR93LC56-W
D7 18 19
D8 Q8
EPROMOUT
NVRAMCSZ 11 CLK
RESETZ 1 VCC RA36
CLR
10K*4
74HC273/SO
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
U19
D[0..15] D0 44 R23 1.5K
D1 D0 J13
43 D1 PUCTL 23
D2 42 1
D3 D2 R24 22 Vcc
41 D3 2 D-
D4 38 1 3
D5 D4 D+ D+
37 D5 4 GND
D6 36 2
D7 D6 D- USB CONNECTOR(TYPE B)
35 D7
D8 22 R25 22 FL27
D9 D8 EXCCET103U
21
CE3000-UM-251-9370
D10 D9
20 D10
D11 Y3 OCETGCA-6.0MHz
19 D11
D12 16 6 3
A[0..21] D13 D12 XIN OUT N.C 1
15 D13
D14 14 4 2
D15 D14 VDD GND
13 D15
A1 32 7 VCC_L C102 104
A2 A0 XOUT
31 FL33
A3 A1
30 A2
A4 29 FL32 EXCCET103U
A5 A3 EXCCET103U
28 A4
A6 27
A7 A5
26 A6
24 ADSEL INTR 12
33 DACK0 DREQ0 34
18 DACK1 DREQ1 25
9 VCC_L
RDZ RD
WRLZ 10 WR VCC0 3
VCC1 40
RESETZ 11 RES
8 C55
USBCSZ CS
4 5 104
RA35 8 7 6 TEST1 GND0
17 TEST2 GND1 39
100K*4
ML60852A
11-11
USBINTZ
VCC
11.2.8 Main Board USB Block Section (PR270101A)
UPC29M33 D9 VCC_L
U21 HSM126S
1 I O 3
G
C59 C60 D10
2
104 47uF/16V
HSM126S
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
2PHASE
2XCSZ
2YCSZ
RESET FANON
RESETZ RESET
CE3000-UM-251-9370
RESETZ
RS
FEEDER-O RW RESETZ
FEEDERO-IN FEEDER-O E RESETZ
FEEDER0-IN LCDB[0..7]
FEEDER1-IN RESET CONNECT D[0..15]
RESET RESETZ
RESETZ RS LOCALZ MEMORY
RW
TXD0 LCDB[0..7] E
RXD0 IOCS1Z LCDB[0..7] FANON
DSR0 IOCS1Z
CTS0Z
DTR-DZ TOMBO
RTS-DZ FR_BUSYZ TOMBO
FEEDER-O
11-12
CPU PENPWMOUT MC+ FEEDER-O
PWMZ IF MC-
PB[0..7]
A[0..21] PB[0..7] PB[0..7]
CINTZ
RDZ CENINT D[0..15]
11.2.9 Main Board Top Section (PR270102A)
WRLZ
CENCSZ CONNECT
CENCSZ
TXD0
RXD0
USB DSR0Z PEN
CTS0Z
A[0..21] USBINTZ DTR-DZ PENPWMIN MC-
USBCSZ RTS-DZ PWMZ MC+ LOCALINTZ
USBCSZ LOCALINTZ
WRLZ FEEDER1-O ADDCSZ LOCALZ
RDZ ADDCSZ FEEDERO-IN
RESET FANON FEEDER0-IN
RESETZ RESET RESETZ
RESETZ RESETZ
D[0..15]
D[0..15] D[0..15]
IF
USB
PEN
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
RA2 RA3
VCC 10K*4 10K*4 VCC
U1A R1 470 2012 30FLT-SM1-TB(0.5mm Pitch)
1 2 74LS06
FL1 J1
1 2 3 4 1 2 3 4 N2012Z121T03 1
PB[0..7] LOCALZ GND
2
11.2.10
KEY0
3 KEY1
PB0 FL2 KCONT0 4
PB1 EXCCET102U D1 1SS352-TPH3 KEY2
5 KEY3
PB2 FL3 KCONT1 6
PB3 EXCCET102U D2 1SS352-TPH3 GND
7 CAM_ANO
PB4 FL4 KCONT2 8
PB5 EXCCET102U D3 1SS352-TPH3 CAM
FEEDER-O 9 PAUSEZ
PB6 FL5 10
PB7 FANON PAUSELED
EXCCET102U 11
TONBOLED ON FL6 KCONT2 GND
12 KCONT2
RA4 RA5 EXCCET102U KCONT0 13
VCC 10K*4 10K*4 FL7 KCONT1 KCONT0
14 KCONT1
EXCCET102U 15
CE3000-UM-251-9370
FL8 VCC
16 VCC
EXCCET102U 17
1 2 3 4 1 2 3 4 VCC
D[0..15] A6H-4101(OMRON) 18 LCD_CNT
D0 2 18 FL9 19
D1 A0 B0 EXCCET102U LCDB0(RS)
3 17 SW1 20
D2 A1 B1 FL10 LCDB1(R/W)
4 A2 B2 16 21 LCDB2(E)
D3 5 15 EXCCET102U 22
D4 A3 B3 PINCH FL11 LCDB0
6 A4 B4 14 23 LCDB1
D5 7 13 CAM EXCCET102U 24
D6 A5 B5 YHOME FL12 LCDB2
8 A6 B6 12 25
D7 EXCCET102U LCDB3
9 A7 B7 11 FR_BUSYZ 26
FL13 LCDB4
27 LCDB5
1 DA5 EXCCET102U 28
DIR FMN1 LCDB6
19 FL14 29
IOCS1Z OE LCDB7
EXCCET102U 30
5
3
2
1
FL15 GND
U3 74HC245/SO RA6 RA7 RA43 EXCCET102U C112
VCC 10K*4 10K*4 10K*4 FL28 104
EXCCET102U
FL29
4 EXCCET102U C111
FL30 47uF/16V
EXCCET102U
RS FL31
RW EXCCET102U
E LCDB0 VCC
LCDB1 VCC
LCDB2
05FMN-BMT-A-TF
LCDB3 R95
LCDB4 470 2012 R4 R5 VCC
LCDB5 J21 8.2K 200
LCDB6 5 R94
LCDB7 ANODE 470 2012
4 GND
3 R93
LCDB[0..7] C2 CAM J6
2 470 2012
101 VCC VCC
1 OPEN 1 PENA
2 PENB
11-13
3 GND
4 YHOME
5 PINCH
6 YH-ANO
7 PI-ANO
R106 200 2012
8 TOMBO
U55B tnbo led drive out 9
R115 2.2K TOMBO-ANO
5 10 VCC
3 Q2 11
2SD1781K GND
6 MC+ 12 MCP
C3 13
C1 FL16 104 MCP
TC7WH08FU MC- 14
101 MCM
15 MCM
C4 16
N2012Z121T03 220uF/50V GND(FG)
+24V VCC
16FMN-BMT-A-TF
VR1
U5 SI-8050 ST-7TA 10K
4 U51A C116 TP1
8
FB 104
R100 10K NJM3404AM
8
VCC U51B
HK-1-S
1 L1 SLF12575-151M1R5 3 +
Vin
C5 2 1 5 +
Vout
2 - 7
D8 R103 TOMBO
220uF/50V 6 -
GND
ON
C6 C113 10K
SFPW-56
4
NJM3404AM
4
3
5
1000uF/10V 472
C114 472 C115
472
R104
R101 150K R105 100K
Main Board Connector Block Section (PR270102A)
10K
R102
10K
J22
+24V LGP3131-0110
J2 VCC
1
2
3
C110
4
B4P-VH 47uF/16V
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
22K*4 22K*4 22K*4 22K*4 22K*4
Y1 XPEEEC6.00MHz VCC RA8 RA9 RA10 RA11 RA12
C104 R97 0
18 *Not instaled
R96
U6
11.2.11
R* AP[18..21]
C105 72 32 AP21
XTAL PB9/IRQ7/A21 AP20
A10
A11
A12
A13
A14
A15
A16
A17
A1
A0
A5
A4
A3
A2
A9
A8
A7
A6
PB8/IRQ6/A20/WAIT 31
18 74 30 AP19
EXTAL PB7/A19 AP18
PB6/A18 29 A[0..21]
VCC 22 A17
A17 A16
73 MD3 A16 20
75 19 A15
MD2 A15 A14
78 MD1 A14 18
79 17 A13
MD0 A13 A12
A12 16
84 15 A11
RES A11 A10
14
CE3000-UM-251-9370
A10 A9
76 NMI A9 13
VCC 12 A8
A8 A7
11 VCC +24V
A7 A6
RA15 10
A6 A5
10K*4 9
A5 A4
R9 8
A4 A3
10K 7 R99
A3 A2
VCC 6 10K J23 B7B-PH-KS
U7 A2 A1
A1 5 1
3 1 4 A0
Vcc VOUT A0 FEEDER0-IN 2
C7 99 FEEDER-O
PF7/AN7 D15 3
U1C U1D 98 PF6/AN6 D15 52 FEEDER1-IN
104 D14 4
4 2 5 6 9 8 RESETZ 97 AVSS D14 53
GND M.R D13 5
96 PF5/AN5 D13 54
PST592DMT D12 6
74LS06 74LS06 95 PF4/AN4 D12 56
D11 7
94 PF3/AN3 D11 57
93 58 D10
PF2/AN2 D10 D9
RESET VCC 92 59 10K*4 10K*4 10K*4 10K*4
PF1/AN1 D9 D8
RA21 91 60 VCC RA22 RA23 RA24 RA25
PF0/AN0 D8 D7
10K*4 100 62
AVCC D7 D6
D6 63
64 D5
D5 D4
LOCALINTZ 49 PA2/SCK0/DREQ0/IRQ0 D4 66
46 67 D3
PA5/SCK1/DREQ1/IRQ1 D3 D2
CINTOUTZ 43 PA8/TCLKCC/IRQ2 D2 68
D1
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
42
D10
D11
D12
D13
D14
D15
USBINTZ PA9/TCLKCD/IRQ3 D1 69
70 D0
D0
D[0..15]
PB2/IRQO/RAS 24 RASZ
PB3/IRQ1/CASL 25 CASLZ
PB4/IRQ2/CASH 26 CASHZ
PB5/IRQ3/RDWR 28 RDWR
WRL 38 WRLZ
WRH 36
R11
11-14
1K 34 RDZ
RD
TOMBO
CS0 41 CS0Z
CS1 40 CS1Z
C8 45 CS2Z
PA6/TCLKA/CS2
PA7/TCLKB/CS3 44 CS3Z
104
PA15/CK 83 PWMZ
PA0/RXD0 51 RXD0
PA1/TXD0 50 TXD0
R12 200 85
PE0/TIOC0A/DREQ0 PENPWMOUT
80 PLLVcc PE1/TIOC0B/DRAK0 86 EPROMDOUT
81 PLLCAP PE2/TIOC0C/DREQ1 87 RTS-DZ
VCC C9 82 PLLVss PE3/TIOC0D/DRAK1 88 DTR-DZ
104
PA3/RXD1 48 CTS0Z
C11 C12 C13 C14 C16 C17 47
PA4/TXD1 DSR0
104 104 104 104 104 104 89
R13 3K PE4/TIOC1A AB-ENZ
C10 470 PE5/TIOC1B 102 RS
106 LCDB0
PE8
107 LCDB1
PE9
108 LCDB2
PE10
GND 110 LCDB3
PE11
111 LCDB4
PE12
112 LCDB5
PE13
1 LCDB6
PE14/DACK0/AH
2 LCDB7
PE15/DACK1
SH7014
Vcc
Vcc
Vcc
Vcc
Vcc
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
Vss
109
71
90
101
55
61
33
39
103
3
23
27
65
77
21
37
VCC
104
C25
C15 104
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.2.12
+24V
+24V
D[0..15]
C65
U32 10uF/50V C66
7
12
D0 3 2 6 100uF/50V
D1 D1 Q1 INA
4 5 U49C 5 J15
VSA
VSB
D2 D2 Q2 INA
6 D3 Q3 7 5 6 17 INB OUTA 8
D3 1
11 D4 Q4 10 16 INB
D4 2
13 12 74HC14 OUTA 1
D5 D5 Q5 3
14 15 U49D
D6 Q6 4
9 8 VCC 18
OUTB 5
2XCSZ 9 CLK 3 REFA
74HC14 6
OUTB 11
CE3000-UM-251-9370
RESETZ 1 R79 14 B6B-XH-A
CLR REFB
47K
74HC174/SO 2
R80 TDA
47K 9
RSA
C94 13
470 TDB
U36 10 R82
GA
GB
RSB
1 3W C98
D6 3 2 222
D1 Q1
4
15
D7 4 5 C95 R81 C99
D8 D2 Q2 470 U33 1 3W 222
6 7 VCC VCC
D9 D3 Q3 SLA7026M
11 10 VCC
D10 D4 Q4 VSELX
13 D5 Q5 12
D11 14 15 EL5220CY
D6 Q6 R108 74HC4052
U35A
8
39K U37 R32
9 R36 R37
CLK 1.5K
10K 20K + 3 13 12
X X0
1 1 X1 14
CLR
- 2 3 Y X2 15
R109 11 R33
R83 X3 1.2K
74HC174/SO R35 10K
4
5.1K 39K DA1 1
Y0
FMN1 Y1 5
1 Y2 2
2 Y3 4
U38 R39 1.8K
3
1 18 5 10 VSELX R34
I1 OUT1 A 3.9K
2 17 9 VSELY
I2 OUT2 B
3 I3 OUT3 16
4
4 15 EN 6
I4 OUT4
5 14 DA2
I5 OUT5
6 13 FMN1 VEE 7 VCC
I6 OUT6 R40 1.8K U1F
7 12 1 16
GND
5 C117
104
TD62593AFP U1B
4
3 4 74LS06
R41 VCC
5.1K R84
39K
C69
11-15
10uF/50V R111 FANON R112
10K 1.5K
+24V
R113
U39 C70 1.2K
7
12
D0 3 2 6 100uF/50V
D1 Q1 INA
D1 4 5 U49E 5 J16
VSA
VSB
D2 Q2 INA
D2 6 D3 Q3 7 11 10 17 8
11 10 INB OUTA 1
D3 D4 Q4 16
13 12 74HC14 INB 2 R114
D4 D5 Q5 1 EL5220CY
14 15 U49F OUTA 3 3.9K
D5 D6 Q6 U35B
13 12 4
VCC OUTB 18
9 5
2YCSZ CLK 3 REFA + 5
74HC14 6
OUTB 11 7
1 7
CLR 14 REFB - 6
R86 B7B-XH-A
74HC174/SO 47K
2 TDA
U41 R85 9
47K RSA
13 TDB
D6 3 D1 Q1 2 C96 10 R88
GA
GB
470 RSB
D7 4 D2 Q2 5 1 3W
D8 6 7 C100 C101
D3 Q3
4
15
D9 11 10 R87 222 222
D4 Q4
D10 13 12 VSELY C97 U40 1 3W
D5 Q5
D11 14 D6 Q6 15 470 SLA7026M
9 CLK
1 CLR
74HC174/SO
R52 R53
10K 20K
R51
5.1K R89
39K DA3
FMN1
1
U42 2
1 18 3 R55 1.8K
I1 OUT1 5
2 I2 OUT2 17
3 I3 OUT3 16
4 15
4
I4 OUT4 DA4
5 I5 OUT5 14
6 13 FMN1
Main Board 2-Phase Motor Drive Section (PR270102A)
TD62593AFP
4
R57
5.1K R90
39K
R58 R59
10K 20K
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.2.13
22K*4
VCC RA13
1 2 3 4
A20
A21
A19
A18
A[0..21]
CE3000-UM-251-9370
AP[18..21]
U54
AP21 2 4 A21
AP20 1A 1Y A20
5 2A 2Y 7
AP19 11 9 A19
AP18 3A 3Y A18
14 4A 4Y 12
VCC
3 1B
R107 6
10K 2B VCC
10 3B
13 U28
4B
1 A19 1 15
AB-ENZ SEL A20 A Y0
15 EN 2 B Y1 14
A21 3 13 0090 0000H 82C55 W/R
C Y2 CENCSZ
S=L:A Y3 12 USBCSZ
74HC157/SO 6 11 0098 0000H USB W/R
S=H:B G1 Y4
CS2SZ 4 G2A Y5 10
5 9 U53A
G2B Y6
Y7 7 00A0 0000H 1
3 NVRAMCSZ
WRLZ 2
74HC138/SO IO
74HC32
WRIGHT
U53B
00B0 0000H 4
6 IOCS1Z
RDZ 5
11-16
IO READ
74HC32
VCC
U31
A2 1 15 00C0 0000H
A3 A Y0 2XCSZ
2 B Y1 14 WRIGHT
A4 3 13 00C0 0008H
C Y2 2YCSZ
Y3 12
6 G1 Y4 11
CS3Z 4 G2A Y5 10
Main Board Decoding Block Section (PR270102A)
5 G2B Y6 9
Y7 7 00C0 001CH ADDCSZ
U55A
WRLZ 1
READ
WRLZ
7 74HC138/SO
RDZ 2
RDZ
TC7WH08FU
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
VCC
11.2.14
D[0..15] 10K*4
RA30 RA31
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
1 2 3 4 1 2 3 4 10K*4
24
39
17
2
U16 DATA[7..0]
D0 32 43 2 18 DATA0
D1 D0 PA0 A1 B1 DATA1
31 42 3 17 J12
VCC
VCC
VCC
GND
D1 PA1 A2 B2
CE3000-UM-251-9370
D2 30 41 4 16 DATA2 DATA7 9
D3 D2 PA2 A3 B3 DATA3 D7
A[0..21] 29 40 5 15 DATA6 8
D4 D3 PA3 A4 B4 DATA4 D6
28 38 6 14 DATA5 7
D5 D4 PA4 A5 B5 DATA5 D5
27 37 7 13 DATA4 6
D6 D5 PA5 A6 B6 DATA6 D4
26 36 8 12 DATA3 5
D7 D6 PA6 A7 B7 DATA7 D3
25 35 9 11 DATA2 4
D7 PA7 A8 B8 D2
DATA1 3
A2 PB0 D1
4 14 19 DATA0 2
A3 A0 PB0 PB1 G JP8 D0
3 A1 PB1 15 1 18 +5V
PB2 DIR DSP03-003-432 B
PB2 16 STB 13 SLC
44 18 PB3 74LS245 A U18B 10
RDZ RD PB3 ACK
34 19 PB4 C 2 1 4 3 1
WRLZ WR PB4 STB
1 20 PB5 11
CENCSZ CS PB5 BUSY
33 21 PB6 U18A 32
RESET RESET PB6 74LS14/SO 74LS14/SO ERROR
23 PB7 14
PB7 OPEN
PB[0..7] 15 OPEN
9 12 GND
PC0
10 16 GND
PC1
11 FEEDER1-O 17 GND
PC2 JP9
13 19 GND
PC3 U18E 74LS14/SO DSP03-003-432
8 U18D 20
PC4 B GND
7 9 8 11 10 21 GND
PC5 A
6 22 GND
PC6 74LS14/SO C
5 23 GND
PC7
BUSY U18F 24 GND
13 12 25 GND
U2 U14A TC7WU04F 26
MSM82C55A-2GS-2K GND
VCC 74LS14/SO 27 GND
1 7 CENINT U18C 28 GND
5 6 29 GND
30 GND
RA44 8 7 6 5 74LS14/SO 31 N.C.
10K*4 VCC 33 GND
RA32
VCC 10K*4 FRC685J036-L/Y
8 7 6 5
11-17
J20 8 7 6 5
1 RA33 RA34 VCC
VCC
2 +XSNS 1K*4 1K*4
3 GND
4 VCC
5 -XSNS
6 GND
VCC
B6B-PH-K
C92
9
U20
224
10 C1+ V+ 11
Vcc
C57
224
C56 12 15
C1- V-
13 C93
104 C58 C2+
224
Main Board Interface Section (PR270102A)
R26 VCC
224 14 R27 1K
C2- R28 1K
1K J14
TXD0 5 T1 IN T1 OUT 2 4 RTS
RTS-DZ 18 T2 IN T2 OUT 1 20 DTR
DTR-DZ 19 T3 IN T3 OUT 24 2 TXD
21 T4 IN T4 OUT 20 3 RXD
5 CTS
RXD0 6 R1 OUT R1 IN 7 6 DSR
CTS0Z 4 R2 OUT R2 IN 3 9 +5V
DSR0Z 22 R3 OUT R3 IN 23 1 SHILED
17 R4 OUT R4 IN 16 7 GND
JP12 B
A
GND
C R29 FCN675J025-L/C#U
SP208ECA SSOP
1K
8
DSP03-003-432
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
D[0..15]
37
27
46
A[0..21]
A[0..21] A1 D0
25 A0 DQ0 29
A2 24 31 D1
VSS
VSS
VCC
A3 A1 DQ1 D2
23 A2 DQ2 33
A4 22 35 D3
A5 A3 DQ3 D4
21 A4 DQ4 38
A6 20 40 D5
CE3000-UM-251-9370
A7 A5 DQ5 D6
19 A6 DQ6 42
A8 18 44 D7
A9 A7 DQ7 D8 VCC
8 A8 DQ8 30
A10 7 32 D9 J19
A11 A9 DQ9 D10
6 A10 DQ10 34 1
A12 5 36 D11
A13 A11 DQ11 D12 2
4 A12 DQ12 39 3
A14 3 41 D13
A15 A13 DQ13 D14 4
2 A14 DQ14 43 5
A16 1 45 D15 A1
A17 A15 DQ15/A-1 A2 6
48 A16 7
A18 A3
A20
VCC 17
A19 A17 A4 8
16 A18 9
15 A5
RY/BY FR_BUSYZ 10
26 A6
CE A7 11
RDZ 28 OE 12
11 A8
WRLZ WE 13
47 A9
RESETZ BYTE A10 14
RESETZ 12 RESET 15
A11
A12 16
U22 MBM29F800BA-70PFTN A13 17
U53C
A14 18
CS0Z 9 19
8 A15
U14C TC7WU04F A16 20
10 21
DEBUG A17
A18 22
6 2 74HC32
A19 23
24
U53D
25
JP20 12
DEBUGZ 26
NORMAL DSP03-003-432 11 27
13 VCC C63
D0 28
D1 29
74HC32 10uF/16V
D2 30
C64 104 D3 31
11-18
D4 32
D5 33
D6 34
D7 35
D8 36
D9 37
42
21
1
37
22
D10 38
D0 D11 39
A1 17 2
A0 DQ0 D1 D12 40
A2 18 3
VSS
VSS
VSS
VCC
VCC
VCC
A1 DQ1 D2 D13 41
A3 19 4
A2 DQ2 D3 D14 42
A4 20 5
A3 DQ3 D4 D15 43
A5 23 7
A4 DQ4 D5 DEBUGZ 44
A6 24 8
A5 DQ5 D6 45
A7 25 9
A6 DQ6 D7 46
A8 26 10
A7 DQ7 D8 47
A9 27 33
A10 A8 DQ8 D9 48
28 A9 DQ9 34 49
16 35 D10
NC DQ10 D11 50
15 NC DQ11 36
VCC 38 D12 8911-050-178S-A
C62 104 DQ12 D13
RASZ 14 RAS DQ13 39
CASHZ 30 40 D14
UCAS DQ14 D15
CASLZ 31 LCAS DQ15 41
RDWR 13 WE
RDZ 29 OE
U23
2
7
U24
Main Board Memory Block Section (PR270102A)
D0 3 2 5 DI 6
D0 Q0 DO
D1 4 5 U27
VCC
GND
D2 D1 Q1 M5M418160CJ-6S
6 D2 Q2 7 3 CS
D3 11 10 4 1
D3 Q3 SK NC
D4 13 12 8
D4 Q4 NC
D5 14 15
D5 Q5
9 BR93LC56-W
NVRAMCSZ CLK
EPROMOUT
RESETZ 1 CLR
5 6 7 8
VCC RA36
74HC174/SO
10K*4
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.2.16
U19
D[0..15] D0 44 R23 1.5K
D1 D0 J13
43 D1 PUCTL 23
D2 42 1
D3 D2 R24 22 Vcc
41 D3 2 D-
D4 38 1 3
D5 D4 D+ D+
37 D5 4 GND
D6 36 2
D7 D6 D- USB CONNECTOR(TYPE B)
35 D7
D8 22 R25 22 FL27
D9 D8 EXCCET103U
21
CE3000-UM-251-9370
D10 D9
20 D10
D11 Y3 OCETGCA-6.0MHz
19 D11
D12 16 6 3
A[0..21] D13 D12 XIN OUT N.C 1
15 D13
D14 14 4 2
D15 D14 VDD GND
13 D15
A1 32 7 VCC_L C102 104
A2 A0 XOUT
31 FL33
A3 A1
30 A2
A4 29 FL32 EXCCET103U
A5 A3 EXCCET103U
28 A4
A6 27
A7 A5
26 A6
24 ADSEL INTR 12
33 DACK0 DREQ0 34
18 DACK1 DREQ1 25
9 VCC_L
RDZ RD
WRLZ 10 WR VCC0 3
VCC1 40
RESETZ 11 RES
8 C55
USBCSZ CS
4 5 104
RA35 TEST1 GND0
17 TEST2 GND1 39
100K*4
ML60852ATB
11-19
USBINTZ
VCC
UPC29M33 D9 VCC_L
U21 HSM1265
Main Board USB Block Section (PR270102A)
1 I O 3
G
C59 C60 D10
2
104 47uF/16V
HSM1265
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.2.17
QA4 L6203
5 IN1 OUT1 3 MC+
7 C85 R75
PENPWMIN IN2 153 39_1W
BOOT1 4
PWMZ 11 ENA
OUT2 1
10 SNS C86 C87
9 8 152/50V
VREF BOOT2 MC-
153
CE3000-UM-251-9370
C88
224
VS
GND
2
6
C90
103
+24V
J9
R17 1
470 2012 2
U1E B2B-EH-A
11 10 Q1
FANON 2SD1286-Z
74LS06 R19 1K
U49B
LOCALINTZ 4 3
11-20
74HC14
D[0..15]
VCC
VCC
7
U48 R70
D0 6 2 5 2 1K
Y1 A1 Q D U49A R71
PR
D1 3 22K
Y2
A2 5 FEEDER0-IN CLK 1 2 1 LOCALZ
ADDCSZ 1 G1
Main Board Pen Drive Section (PR270102A)
7 3 C83
G2 Q CL 74HC14 C82 102 104
TC7WH125FU U50
6
TC7WH74FU
RESETZ
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
VCC
+5V
3
1
+5V
4
J401
GND 30 J402
11.2.18
5
2
KEY3 26 9 KCONT1
GND 25 8 KEY2
CAM_ANO 24 7 KEY3
CAM 23 6 KEY0
PAUSEZ 22 5 KEY1
PAUSELED 21 4 KCONT0
GND 20 3 KCONT2
KCONT2 19 2 GND
18 1 VCC VCC
KCONT0 GND
17
CE3000-UM-251-9370
KCONT1
VCC 16 J501
VCC 15 12FMN-BMT-A-TF(1.0mm Pitch straight) PENA 16 J505
VCC 14 PENB 15 1 VCC
LCD_CNT 13 GND 14 2 LEDDRV
LCDB0(RS) 12 YHOME 13 3 TOMBOSNS
LCDB1(R/W) 11 PINCH 12 4 VCC
LCDB2(E) 10 YH-ANO 11 S4B-PH-SM3-TB(2.0mm)
LCDB0 9 PI-ANO 10
LCDB1 8 TOMBO 9 J502
LCDB2 7 TOMBO-ANO 8
LCDB3 6 VCC 7 5 ANODE
LCDB4 5 GND 6 4 GND
LCDB5 4 1 MCP 5 3 PINCH R
GND
LCDB6 3 2 MCP 4 2 VCC
Vcc
LCDB7 2 3 MCM 3 1 OPEN
LCD_CNT
GND 1 4 RS MCM 2
5 FG 1 05FMN-SMT-A-TF
R/W
6 E
30FLH-SM1-TB (0.5mm angle) 7 LDB0 16FMN-SMT-A-TF J503
8 LDB1
9 MCM
LDB2 1 MCP
10 LDB3 2
11 LDB4
12 LDB5 S2B-PH-SM3-TB
13 LDB6
14 LDB7 J403 C501 104
14FMN-BMT-A-TF(1.0mm straight) J504
LCD Unit Flexible Cable PENA
1 VCC
2 PENB
Key Relay Board PR270104A 3 GND
4
04FFS-SP-TF(JST1.25mmPitch)
11-21
Pen Relay Board PR270105B
Relay and Sensor Board Section
J701 J901
3
1
U901
J601 1 1
3
1
ANODE VCC
1 2 2
3
1
ANODE GND LEDDRV
2 PINCH R 3 4 3
GND TOMBOSNS
3 4 VCC 4 4
CAM VCC
4 OPEN 5
VCC
OPEN 5 U701
U601 05FMN-SMT-A-TF LG-207D KR1228
2
05FMN-SMT-A-TF LG-207D
5
2
5
2
Auto Registration Mark Sensor Board
Cam Sensor Board PR270107A PR270109A
Pinch Roller Sensor Board PR270106A
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.2.19
CE3000-UM-251-9370
D1
LED GREEN
2
2
2
2
SW11
SW1 SW2 SW3 SW4
\ PAUSE 1
\
\
\
PAUSELED
1
1
1
1
1 2 2 PAUSEZ
3 VCC
4 KCONT1
NEXT SW9 5 KEY2
6 KEY3
1 2 7 KEY0
8 KEY1
11-22
9 KCONT0
10 KCONT2
11 GND
12 GND
SW10
1 2
2
2
2
2
SW5
PREVIOUS SW6 SW7 SW8
ORIGIN TEST ENTER
CONDITION
1
1
1
1
Control Panel Membrane Switch Panel Section
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
J1101 J1102
1 1
2 2
IL-G-2P-S3T2-SA
B2B-XH-A
J1103 J1104
1 1
2 2
3 3
4 4
B4B-XH-A IL-G-4P-S3T2-SA
J1201 J1202
1 1
2 2
B2B-EH-A B2B-EH-A
J1203
1
2
B2B-EH-A
HEDS-9720#P50
CE3000-UM-251-9370 11-23