Professional Documents
Culture Documents
HST System Products Catalogue2010
HST System Products Catalogue2010
2
Conventional Fire Alarm System
It has two LEDS on each detector to provide a local 360° viewing alarm
indication.
It flashes every five seconds, indicating that power is applied and the
detector is working properly.
The LEDS latch on in alarm. LEDS will be off when a trouble condition
occurs indicating that the detector sensitivity is outside the listed limit. The
alarm can be reset only by a momentary power interruption.
This detector supports External Remote indication LED.
3 4
Conventional Fire Alarm System Conventional Fire Alarm System
Conventional Ultra Violate Flame Detector Remote Indication LED
Model: HD104 Model: HS104
This detector uses a very High Sensitivity UV Filter to Detect fast flame The HS104 is a Conventional Remote Indication LED which connects to a
fires. detector to show the alarm conditions on a bright Red Colour LED
Highly reliable, long life UV receptor tube. Optional white or red color cover
Low power consumption. Supports European and USA standards at the same time
HD104 can be intermixed with other types of detection on the panel's Modern style
detection circuitry.
Easily maintained: cleaning can be accomplished without disassembling
the detector.
This detector is designed to be used with most conventional fire alarm
control panels where it can work from 9Volts to 32V D.C.
It has two Led’s on each detector to provide local 360° viewing alarm
indication.
Push in and Pull Down Call Point Zones Fault LEDs indication, Zones Isolation LEDs indication
Fault Relay Output, Auxiliary Output for 28Volts
Can be reset by key RS485 Port for repeaters up to 1.2Km
Red colour Up to 8 repeaters can be connected to one panel
2 sound outputs
Fire proof materials Switched mode power supply 24V,3A with 2 battery chargers 12V
470 Ohm Resistance End of Line Status Detection, Short circuit /open circuit detection
Open collector fault output
Modern style Call Point 28V 50mA fused supply output on Fire
Switched mode power supply 3A output
5 6
Conventional Fire Alarm System Conventional Fire Alarm System
12-Zones Conventional Fire Alarm Panel Conventional Fire Alarm Panel 4 Zones
Model: HP101-12 Model: HP101U-4
HP101-12 is a conventional fire detection control panel and indication General:
control panel designed to meet all the requirements of EN54-2&4
Microprocessor-based conventional fire alarm control panel The HP101U Series Conventional Fire Alarm Control Panel is a 24 volt,
One man test four to sixteen-zone, Class B, Conventional Fire Alarm Control Panel.
12 Detection Zones Panel, 32 Detectors per Zone Designed exclusively to meet the latest market requirements and future
2 Relay outputs for fire condition ULC codes, the highly cost-effective IDC1000 Series can be used in a
Zones Fault LEDs indication, Zones Isolation LEDs indication
Fault Relay Output, Auxiliary Output for 28Volts variety of low- to medium-sized applications.
RS485 Port for repeater up to 1.2Km Specifications:
Up to 8 repeaters can be connected to one panel
2 sound outputs AC POWER : 90 to 270 VAC, 50 Hz, 3.0 amps.
Switched mode power supply 24V,3A with 2 battery chargers 12V Wire size: minimum 14 AWG (2.0 mm²) with 600-volt insulation.
End of Line Status Detection, Short circuit /open circuit detection
Open collector fault output BATTERY: Sealed lead-acid batteries only. Maximum charging circuit:
28V 50mA fused supply output on Fire 27.6VDC @ 0.8 Amp
Switched mode power supply 3A output Features:
Four to Sixteen Zone, Style B (Class B) Initiating Device Circuits (IDCs).
All zones accept two-wire smoke detectors and any normally-open
16-Zones Conventional Fire Alarm Panel Conventional Fire Alarm Panel 8 Zones contact devices.
Model: HP101-16 Model: HP101U-8 Zones 1 - 4/8/16 configured as general alarm zones.
HP101-16 is a conventional fire detection control panel and indication
control panel designed to meet all the requirements of EN54-2&4 All circuits are power-limited and supervised, meeting the latest ULC
Microprocessor-based conventional fire alarm control panel requirements using fuse-less technology.
One man test
One to Four built-in, Style Y (Class B) Notification Appliance (Signal)
16 Detection Zones Panel, 32 Detectors per Zone
2 Relay outputs for fire condition Circuits (NACs).
Zones Fault LEDs indication, Zones Isolation LEDs indication NACs may be programmed: Silence-able. Non-Silence-able. Auto-Silence
Fault Relay Output, Auxiliary Output for 28Volts
(5 to 20 Minutes).
RS485 Port for repeater up to 1.2Km
Up to 8 repeaters can be connected to one panel 1.25 amps of NAC power & 3.0 amps of total system power.
2 sound outputs
Alarm, Trouble and Supervisory, Form-C relays standard. & 24-volt
Switched mode power supply 24V,3A with 2 battery chargers 12V
End of Line Status Detection, Short circuit /open circuit detection operation.
Open collector fault output Resettable four-wire smoke detector power @ 500 mA. Non-resettable
28V 50mA fused supply output on Fire power @ 500 mA.
Switched mode power supply 3A output
Integral battery charger capable of charging up to 18 AH batteries
Conventional Fire Alarm
7 8
Conventional Fire Alarm System Fire Fighting System & EX-Proof Detector
Conventional 6"/8"/10' Bell Conventional Fire Fighting & 4 Zones Alarm Panel
Model: HB101/HB102/HB103 Model: HP102-4
This conventional Bell has a very low power consumption. HP102-4 is a conventional fire Fighting and detection control panell
designed to meet all the requirements of EN54-2&4
Voice volume: 96dB/(mA)
Microprocessor-based conventional fire fighting & alarm control panel
Rated current: 10 to 18 mA 4 Detection Zones Panel, 1 Fire Fighting Area, 20 to 32 Detectors per
Size: 6"/8"/10" of DC 24V Zone
Temperature: -10 ~ 60° Relay output for fire condition, Relay output for double knock condition
Zones Fault LEDs indication, Status for all steps of fire fighting
Humidity: at or below 93%
Fault Relay Output, Auxiliary Output for 28 Volts
Material : steel Sound output for Alarm & firefighting Condition
Water Proof Up to 8 repeaters can be connected to one panel
Switched mode power supply 24 V,3A with 2 battery chargers 12V
End of Line Status Detection, Short circuit /open circuit detection
Release switch for gas release, Manual automatic switch control
Hold Switch, Enable / Disable key switch
Conventional Sound Strobe Ex-Proof IR/UV Flame Detector with Relay Output
Model: HS101 Model: HD124 - IR/UV-Ex
This Conventional Siren has a very low power consumption. Compatible with all the fire alarm and gas detection system
Rated Voltage: 24 Volts Response to a flame more than 25m away
Rated current: 50mA Unaffected by convention currents, draughts or wind and solar-blind
Sound: 89dB/3m(A) Tolerant of fumes, vapours, dust and mist
Light Output: ≥ 1.2WS Alarm Relay Output(NO/NC can be adjustable)
Flash Rate: ≤ 2 seconds Unpolarized wire input
Wide range of operating voltages(9V~28VDC)
Material: Fire Proof Plastic
Quick Detection of IR/UV Flame from Distance
Temperature:-10 to 60° Built in microprocessor intelligent software
Humidity:≤93%
9 10
Mini Fire Alarm System Intelligent Addressable Fire Alarm System
Mini Conventional Fire Alarm Panel 2/4 Zones Intelligent Addressable Photoelectric Smoke Detector
Model: HP101-2/4 Model: HD201
HP101-2/4 is a conventional fire detection control panel and indication This Intelligent Addressable Photo-Electric Smoke Detector uses an
control panel designed to meet all the requirements of EN54-2&4
intelligent optical sensing chamber.
Microprocessor-based conventional fire alarm control panel.
This detector is designed to provide open area protection and to be used
2/4 Detection Zone Panels, 20 to 32 Detectors per Zone
with our HST Protocol panels.
2 Relay outputs for fire condition
It has two LEDs on each detector to provide a local 360° viewing alarm
Zones Fault LEDs indication, Fault Relay Output
indication.
2 sound outputs
It flashes every five seconds, indicating that power is applied and the
Switched mode power supply 24V,3A with 1 battery charger 12v
detector is working properly.
End of Line Status Detection, Short circuit /open circuit detection
The LEDs latch on in alarm. The LEDs will be off when a trouble condition
Open collector fault output
occurs, indicating that the detector sensitivity is outside the listed limit.
28V 50mA fused supply output on fire
The alarm can be reset only by a momentary power interruption.
Switched mode power supply 3A output
This detector supports External Remote indication LED.
Simple Double Knock fire fighting fucntion
4-Wire Photoelectric Smoke Detector with Relay Output Intelligent Addressable Fixed & Rate-of-Rise Heat Detector
Model: HD101-Mini Model: HD202
This Intelligent Addressable Fixed & Rate-of-Rise Heat Sensor uses a
This Mini Detector uses an intelligent optical sensing chamber. thermal sensing element for detection
Compatible with all the security and fire alarm system This detector is designed to provide open area protection and to be used
Mini Size suitable for all installed inside cabinet with our HST Protocol panels.
It has two LEDs on each detector to provide a local 360° viewing alarm
Alarm Relay Output(NO/NC can be adjustable)
indication.
Unpolarized wire input
It flashes every five seconds, indicating that power is applied and the
Wide range of operating voltages(9V~28VDC)
detector is working properly.
Unique optical sensing chamber
The LEDs latch on in alarm. The LED’s will be off when a trouble
Two LEDs blink standby, provide 360° visibility
condition occurs, indicating that the detector sensitivity is outside the
Insect-resistant screening
listed limit. The alarm can be reset only by a momentary power
Drift compensation and smoothing algorithms
interruption.
Mini Fire Alarm System This detector supports External Remote indication LED.
4-Wire Photoelectric Smoke & Heat Detector with Relay Output Addressable Fire Alarm Intelligent Addressable Multi Photoelectric Smoke & Heat Detector
Model: HD103-Mini Model: HD203
This Intelligent Addressable Multi-Detector uses an intelligent optical
This Mini Multi-Detector uses an intelligent optical sensing chamber and a sensing chamber and a thermal sensor at the same time to detect smoke
thermal sensor at the same time to detect smoke and heat. and heat.
Compatible with all the security and fire alarm system This detector is designed to provide open-area protection and to be used
Mini Size suitable for all installed inside cabinet
Smoke Alarm
11 12
Intelligent Addressable Fire Alarm System Intelligent Addressable Fire Alarm System
Intelligent Addressable Ultra Violate Flame Detector Intelligent Addressable Fire Alarm Panel 1-4 Loops
Model: HD204 Model: HP201
HP201 (IRIS) is an addressable fire detection and indication control panel
This detector uses a very High Sensitivity UV Filter to detect fast flame designed to meet all the requirements of EN54. Certificate EN541-2/4
fires. Modular type panel, 1 to 4 Loop Panel
Highly reliable, long life UV receptor tube 318 addresses per loop (159 detectors / 159 modules )
Low power consumption 1272 Device maximum per panel
96 programming zones for each programming zone delay
HD204 can be intermixed with other types of detection on the panel's 128 programmable input output
detection circuitry. 8 Cause-and-Effect scan be programmed
Easily maintained: cleaning can be accomplished without disassembling Color Graphics LCD 320X240 displaying fire fault and messages
the detector. Touch screen display to operate the panel easily
This detector is designed to be used with most HST Addressable TCP/IP port for programming and networking, up to 32 panels or
repeaters in one network, also used for software monitoring function
Protocols. USB Port for programming and firmware upgrade
It has two LEDs on each detector to provide a local 360° viewing alarm Day/Night setting for detectors , 10000 Event Log Memory
indication. 4 Programmable Relay output, 4 Programmable sound outputs
This detector supports External Remote indication LED. Switched mode power supply 12V,4A with battery charger 12v,18AH
Supports HST or SYSTEM SENSOR protocol
Intelligent Addressable Natural Gas Detector Intelligent Addressable Short Circuit Isolator Module
Model: HD205 Model: HM201-SC
The Gas Detector is designed for single station use. It is small and Model HM201-SC is a negative-switching Loop Isolator, which is
compact, small commercial properties and features. It is intended to fully compatible with HST intelligent addressable protocol.
detect leakage of natural gas (methane gas), town gas, and bottled gas The module incorporates an amber LED to show when it is isolating
(propane gas). a section of the loop, and when used under each addressable
The detector is designed to use HST Addressable Protocol panels. The sensor. If a single short circuit was to occur on the loop, then no
gas Detector can be set high (for methane gas) or low (for propane (LPG) Sensors would be lost.
gas). The HM201-SC does not use an address, and has the same wiring
It detects all sorts of combustible gases, natural gas (methane), bottled configuration as the HD200 Base, making it very simple to install.
gas (propane), LPG (Liquefied petroleum Gas), LNG (Liquefied natural Detects short circuits on loop
gas), coal gas, including town gas. Status LED
Easy to install, mounting bracket included. Allows connection of sensors from the HST Range
High quality durable sensor. Bayonet slot, low insertion force for detectors
Self-diagnostic function by MCU intelligent software. Quick connection via square cable clamps
Excellent reliability & high stability, Ideal for all kitchens.
Can be reset by key time within which the sounder will operate, before automatically silencing
Red colour itself, ideal for minimising noise pollution.
Fire proof materials Loop Powered
Single Loop Address - addressed via the Hand Held Programmer
HST Addressable Protocol
Variable Sound Output 70 ~ 85dB(A) (±2dB(A)) output at 1 metre
Modern style Call-Point Fits HST Standard or HD200 Base
Weatherproof Kit available
51 User-Selectable Tones (all tones EN54-3 compatible)
Also available in white
13 14
Intelligent Addressable Fire Alarm System
Intelligent Addressable Relay Module
Model: HM201-R
Model HM201-R is a single Relay Controller designed to provide one
general-purpose relay output; this output can be driven separately for
control of such devices as dampers or for control of plant and equipment
shutdown.
Loop Powered
Single Address
One Relay Controlled by loop
Relays Contact Rated at 30Vdc at 1 amp
15