Professional Documents
Culture Documents
ESP8266 WIFI Module.
ESP8266 WIFI Module.
ESP8266 WIFI Module.
1. Connect DC 5V power supply at input terminal ‘IN+’ and ‘IN-’ which has marked on PCB.
2. Install APP ‘EspTouch_Demo’ on Android phone. User needs to configuration WIFI
account number and password by MODE 2 at first time to use it.
3. Install TCP transport tool APP ‘EasyTCP_20’ on Android phone. It is used to send the relay
control command, click ‘SWITCH’, and then press the gray square in the interface to input
the name and content of the relay control command respectively (the command format is
HEX).
1. It mean that the configuration is complete if green LED flashes cycle from 4 seconds slow
down to 2 seconds after power on;
2. The module sends a AP WIFI hotspot signal, which can be viewed in the WIFI network of
the mobile phone, and then select the network.
3. Open APP ‘EasyTCP_20’,click ‘CONNECT’,input IP address:192.168.4.1 and port number
8080.And then click ‘Connect’.Green LED flashes cycle from 2 seconds to keep ON after
the connection is successful.Click on the gray square to send an instruction to control the
relay’s switch.
Work Mode 2(Phone and WIFI module carry on router together):
1. Short press S1 button to switch work mode to MODE 2 when green LED flashes cycle from
4 seconds slow down to 2 seconds after power on. And then blue LED turn ON. Green
LED flashes cycle from 2 seconds faster to 0.5 seconds. It means that ESP8266 is waiting
for the “EspTouch_Demo” APP to configure WIFI account number and password.
2. Open APP ‘EspTouch_Demo’ and input router password and then click ‘Confirm’.
3. Wait for the configuration to succeed. When the IP address of the ESP8266 (such as
192.168.0.174) appears on the APP interface. It means that the ESP8266 module is
successfully connected to the router, and the account and password are automatically
remembered. The next time when user enter mode 2, it will automatically connect (about
20-60 second);
192. Note:’192.168.0.174’ This IP address is dynamically assigned to the
ESP8266 module by the router. The address may change after the next re-
connection. User can view the real-time IP address of the ESP8266 module in the
device list of the router.
4. Open the “EasyTCP_20” APP, click “CONNECT”, enter the IP address of the ESP8266
module: 192.168.0.174 and port number 8080, and then click “Connect”. After the
connection is successful, the green flashing from 2 seconds to keep ON. Click on the gray
square to send an instruction to control the relay’s switch.
Additional features(Used as USB Relay):
• For the first time, it will take a little longer (about 1 minute) to configure the WIFI password.
After the configuration is completed, it will take 20 seconds to automatically connect at next
boot.
• If user want to change the router, the user can reset or press the S2 button(the WIFI
account and password of the previous memory will be cleared by press the S2 button), and
the WIFI account and password will be configured for esp8266 in mode 2.
• When ESP8266 memory router signal is very weak or not in service area lead to the
suspension of connection, the green light will go out and try to connect automatically,
buttons are invalid state in the process when the green light is change to 2-second slow
flash which means it has returned to the connection.
• The button can be use when the green light is 2 seconds slow flash or keep on at Mode 1
and mode 2, and the rest is self-configuring in the chip or waiting for the configuration
process, and the button is invalid.
• The mobile phone and esp8266 will automatically disconnect the TCP connection if there is
no data communication for more than 6 minutes. And then click “CONNNECT” in the upper
right corner of “EasyTCP 20” APP to re-establish the connection.
• It’s a relay output. So it can not output voltage. It just like a switch. Work voltage and load
voltage are indispensable.
• Please read user manual and description before use.