Professional Documents
Culture Documents
Rotobin (Sensor de Nivel para Cilos)
Rotobin (Sensor de Nivel para Cilos)
PRINCIPLE FEATURES
The SE series operating principle is simple. A unit 1 Airtight sealing device, outdoor application is
is usually located through a bin wall at the top, available.
middle or low level of a bin. During normal 1 Unique sealing ring design, it can perform good
operation (no material present) a synchronous dust protection to avoid the dust permeate into
motor rotates the paddle at 1 RPM. When this housing body along with the shaft.
paddle rotation is impeded by material, 1 The torque force is adjustable.
surroanding the paddle, motor will stall and cause 1 The performance of torsion is stable and reliable.
the Micro switch to change state. (indicating an 1 If the rotary paddle bears an extra overload, the
alarm or control) motor will be appeared slide to prevent the
inside mechanism damaged.
1 It is rationally designed, the inside mechanisms
are easily tore down for checking, maintenance
APPLICATIONS and replacement. It doesn't necessary to
Suitable for powdery producing & processing remove the complete set from the tank.
industries such as plastic, chemical, medical, 1 Very suitable for small tank and material of low
forage, cement and fertilizer powders. density
STRUCTURE SHAFT
BODY
PADDLE
OIL-SEAL
NUT
Paddle Clutch
assembly Case
Body
Shaft TORQUE SPRING
Micro
Bearing Switch
Nut
Oil seal
Motor
Cable
1
FlneTek
WORKING PRINCIPLE & TORQUE ADJUSTING
AC 110V NC COM NO
or AC 24V
AC 220V or NC COM NO
AC 110V
Available: SE110, 120, 130, 140, 160, 170 or
AC 220V
Available: SE180
2
FlneTek
STANDARD SPECIFICATION
1 Power source : A-110VAC, B-220VAC, C-240VAC, 50/60Hz 1 Torque : 0.5 ~1.0 kg-cm
1 Power consumption : 3W 1 Connect : 1"PF screw or JIS 2-1/2"H5kg/cm2 flange
1 Contact capacity : SPDT, 5A/250VAC 1 Protection/ material : IP65 / ADC-12
1 Rotary speed : 1 R.P.M. 1 Conduit : 1/2"PF
1 Insulation test voltage : AC 1500VH1minute 1 Specific gravity : 0.5g/cm3 (30Lb/ft3)
SE110A/B/C
SCREW TYPE
Horizontal mounting
SE110A/B/C SE111A/B/C
Temp. (-10BC ~ 70BC) PCD130
4-f15
Weight: 1.2 kg 1"PF
f155
RP111A/B/C
100 f97 100 f97
FLANGE TYPE
Horizontal mounting f10 f 10
Temp. (-10BC ~ 70BC)
30
Weight: 1.7 kg 30
90 1/2"PF
1/2"PF
210 4 118
SE120A/B/C 210
SHAFT PROTECTIVE
TUBE TYPE
Horizontal /Vertical mounting
Temp. (-10BC ~ 70BC) SE120A/B/C SE130A/B/C
Weight: 1.2 kg
f97
The whole section from flange
to paddle are made of SUS 304 f97
Standard Length (option): 1/2"PF
L--250mm (2.2 kg) 1/2"PF
118
L--500mm (2.5 kg)
L--750mm (2.8 kg) 146
f155
Special length is made by order
f155 PCD130
f10 4
SE130A/B/C
SHAFT LENGTH 4
4-f15
ADJUSTABLE TYPE f9
PCD130
Vertical mounting f27.2
4-f15
Temp. (-10BC ~ 70BC) f10 L L
f12.7
Standard Length (option):
L-- 450 ~650mm (2.5 kg)
L-- 650 ~1000mm (2.8 kg) 80
L-- 750 ~1200mm (3.0 kg) f8
Special length is made by order
65
30
100
3
FlneTek
STANDARD SPECIFICATION
1 Power source : A-110VAC, B-220VAC, C-240VAC, 50/60Hz 1 Torque : 0.5 ~1.0 kg-cm
1 Power consumption : 3W 1 Connect : 1"PF screw or JIS 2-1/2"H5kg/cm2 flange
1 Contact capacity : SPDT, 5A/250VAC 1 Protection/ material : IP65 / ADC-12
1 Rotary speed : 1 R.P.M. 1 Conduit : 1/2"PF
1 Insulation test voltage : AC 1500VH1minute 1 Specific gravity : 0.5g/cm3 (30Lb/ft3)
SE140A/B/C
HI-TEMP TYPE SE141A/B/C
Horizontal mounting
f97
Temp. (-10BC ~ 200BC) SE140A/B/C
Weight: 2.1 kg
1/2"PF
4-f15 PCD130
SE141A/B/C f155
175
HI-TEMP SHAFT
PROTECTIVE 100 f97
TUBE TYPE f10
f155
Horizontal /Vertical mounting
PCD130
Temp. (-10BC ~ 200BC) 4
30
The whole section from flange 4 1/2"PF
to paddle are made of SUS 304 87 175 4-f15 f27.2
Standard Length (option): f10 L
L--250mm (2.6 kg)
L--500mm (2.9 kg)
L--750mm (3.2 kg) 80
Special length is made by order
65
SE146/A/B/C SE146A/B/C
HI-TEMP SHAFT
f97 SE160A/B/C
LENGTH ADJUSTABLE
TYPE f97
Vertical mounting 1/2"PF
Temp. (-10BC ~ 200BC)
1/2"PF
Standard Length (option): 175 118
L-- 450 ~650mm (3 kg)
L-- 650 ~1000mm (3.3 kg) f155
L-- 750 ~1200mm (3.5 kg)
f155
Special length is made by order 14
PCD130 f10
PCD130 f10 4
SE160/A/B/C 4-f15
4-f15 f9
CABLE WIRE TYPE f6
Vertical mounting L
L
Temp. (-10BC ~ 70BC) f12.7
Standard Length (option):
L-- 450mm (2.5 kg)
f28
L-- 650mm (2.8 kg)
L-- 750mm (3 kg) 30 30
Special length is made by order 100 100
4
FlneTek
STANDARD SPECIFICATION
1 Power source : A-110VAC, B-220VAC, C-240VAC, D-24VAC 50/60Hz 1 Temp. : -10LC ~ 70LC
1 Power consumption : 1.5W 1 Cable length : 30cm (available for custom length)
1 Contact capacity : AC 250V 3A 1 Torque : 30 ~100 kg-cm
1 Rotary speed : 1 R.P.M. 1 Specific gravity : 0.3g/cm3 (20Lb/ft3)
1 Protection/ material : IP65 / PC
SE180A/B/C/D SE1809CRI
SE180A/B/C/D 194
175 62
CROSS-LIKE 4 40
47
BLADE PADDLE 47
f6
Horizontal mounting f6
80
Weight : 0.42 kg f65 100
f65
3/4"PF
3/4"PF
30
SE1809CRH SUS304
0.5mm2x6C cable 30 2
0.5mm x6C cable
SCIMITAR TYPE Standard length 300mm Standard length 300mm
PADDLE
Horizontal mounting SE1809CRH
Weight : 0.42 kg 265
133 47
SE1809CRI f65
f6
RECTANGLE 100H30 3/4"PF
SUS304 PADDLE
Horizontal mounting
Weight : 0.48 kg 0.5mm2x6C cable
Standard length 300mm
SE1849CRI
SE1849CRI L=150~400 182
30 80
HI-TEMP TYPE
SUS304 PADDLE f6 3/4"PF
Horizontal / Vertical mounting
100 f21.7
Temp. Max: 200BC f65
22
f88
0.5mm2x6C cable
Standard length 300mm
4 Paddle Introduction (Mini)
G H I
80 98 W
30
120 H
(G) Cross type paddle (H) Scimitar type paddle, directly ( I ) 100x30 (WxH)
material: PC screwed through 3/4" diameter Material: SUS304
fixed hole. Material: PC
5
FlneTek
EXAMPLES OF MOUNTING
6
FlneTek
EXAMPLE
SE130
SE141
SE110
SE120
15
SE111
INSTALLATION NOTICES
1. Please side mount the sensor by inclined 15 B~20 B to decrease the material inflowing impact.
2. For High Temperature application whereby the temperature inside the tank is more than 70BC
please use SE149 Series.
3. SE110~SE140 on 1"connection pipe inlet, please apply scimitar type to screw directly.
4. SE130, SE146 family items are with flexible and extensible shaft.
5. Please ensure that the Cable Gland point downwards and the nut must be fastened to secure
the device.
7
FlneTek
ORDER INFORMATION
SE1 99 9 99 9 9999
Model
19 : Standard type 60 : Cable wire type
20 : Shaft protective tube type 89 : Mini type
30 : Shaft length adjustable type
49 : Hi-temp type
Voltage
A : 110V B : 220V C : 240VAC D : 24VAC 50/60HZ
Mounting
Paddle Shapes
SE110~SE160 A B,C,D E F
132
A : 100x30 (WxH)
B : 65x80 (WxH) W W
W 100
C : 65x120 (WxH)
D : 80x80 (WxH) H
H
E : 50x30 (WxH) H
30
F : Scimitar G H I
Order Notice
1. Please make sure the Voltage 24VAC, 110VAC, 220VAC or 240VAC, 50/60 Hz.
2. Please make sure the side or top mounting.
3. Please make sure the material specific gravity (S.G.) value.
4. Please make sure whether any bridge block or vibrating motor installed onto the tank wall.
Please try to apply our item SA140 capacity sensor.
5. Please make sure the rotary paddle size is available to enter into the flange inlet.
8
FlneTek
SPECIFICATION
1 Power source : A-110VAC, B-220VAC, C-240VAC, 50/60Hz 1 Connect : 1"PF screw or flange 1"~6"
1 Power consumption : 3W 2-1/2"H5kg/cm2 (std.)
1 Contact capacity : SPDT, 3A/250VAC 1 Enclosure material : AL Alloy, ADC-12
1 Rotary speed : 1 R.P.M. 1 Enclosure Protection : Ex d IIB T4~T6
1 Insulation test voltage : AC 1500VH1minute 1 Conduit : 1/2" (std.) or 3/4"NPT
1 Torque : 0.5 ~1.0 kg-cm 1 Specific gravity : 0.5g/cm3 (30Lb/ft3)
100 f113
f10
f155
30
4- f15 20 108
PCD 130 RP74 A/B/C
RP73 A/B/C EXPLOSION PROOF
EXPLOSION PROOF f113 HI-TEMP TYPE
SHAFT LENGTH Horizontal mounting
ADJUSTABLE TYPE Temp. (-10BC ~ 200BC)
Vertical mounting 108
Temp. (-10BC ~ 70BC) PCD 155
4-f15 45 108
Standard Length (option): 30
f155
L-- 450 ~650mm 20
L-- 650 ~1000mm 14
L-- 750 ~1200mm
f10
Special length is made by order f100 f113
f9.5
L=450~ 4- f15
f14 PCD 130 f155 f90
1200 mm 85
30
100
9
FlneTek
SPECIFICATION
f90 f90
f155 20
45 45 14
f155
14
1"PF f14
f27.2
PCD 130
f9.5 4-f15
f10 f9.5 PCD 130 L=450~
L=250~ f14 4-f15
L=450~ 4000 mm
750 mm
1200 mm f12.7 f28 108
30
30 100
f100
10
FlneTek
ORDER INFORMATION
SE1 99 9 99 9 9999
Model
70 : RP70 Screw type 74 : RP74 Hi-temp type
71 : RP71 Flange type 75 : RP75 Hi-temp shaft protective tube type
72 : RP72 Shaft protective tube type 76 : RP76 Hi-temp shaft length adjustable type
73 : RP73 Shaft length adjustable type 77 : RP77 Cable wire type
Voltage
A : 110V B : 220V C : 240VAC D : 24VAC 50/60HZ
Mounting
Paddle Shapes
A B,C,D E F
A : 100x30 (WxH) 132
B : 65x80 (WxH)
C : 65x120 (WxH) W W
W 100
D : 80x80 (WxH)
E : 50x30 (WxH) H
H
F : Scimitar H
30
Length (mm)
Order Notice
1. Please make sure the Voltage 24VAC, 110VAC, 220VAC or 240VAC, 50/60 Hz.
2. Please make sure the side or top mounting.
3. Please make sure the material specific gravity (S.G.) value.
4. Please make sure whether any bridge block or vibrating motor installed onto the tank wall.
Please try to apply our item SA140 capacity sensor.
5. Please make sure the rotary paddle size is available to enter into the flange inlet.
11
FlneTek