Professional Documents
Culture Documents
Tutorial Kalibrasi Oscilloscope - Tugas BING
Tutorial Kalibrasi Oscilloscope - Tugas BING
1. Oscilloscope
2. Power cable
3. Oscilloscope probe
After all the equipment is prepared, you need to follow these steps:
Prepare the necessary equipment and check the probe cable and power cable, make sure
everything is in good condition. Cable checking can be done using a multimeter. This check
is intended so that the calibration process can run smoothly.
Connect the power cable to the power source
The next step is to connect the 3 pin power cable terminal to the socket on the back of the
oscilloscope and connect the power cable plug to a single phase power source.
Turn on the oscilloscope by pressing the power button located at the bottom right of the
oscilloscope screen, then make sure the oscilloscope screen can light up clearly which is
indicated by a line that appears on the screen. If the line still looks blurry, you can adjust the
focus first by rotating the focus knob at the bottom of the screen and adjusting it to the
appearance of the line on the screen so you can see it clearly. In addition, make sure the line
that appears is straight and is right in the middle of the screen, if the line is slightly slanted,
fix it immediately by rotating the slope of the line in the hole at the bottom of the screen
using a screwdriver. And to adjust the position of the line to the middle, then rotate / adjust
the position knob which is located above the volt/div channel 1 selector.
Plug the BNC probe connector into the BNC channel socket to be calibrated. For
convenience, attach the BNC probe connector to the BNC channel 1 socket first.
The next step is to set the mode switch and source switch to channel 1, and make sure the gnd
(ground) button which is located under the channel 1 volt/div selector is not pressed.
Attach the Probe Tip to the CAL terminal
In this step, connect the red (+) probe tip to the CAL terminal on the oscilloscope which is at
the bottom left of the screen. In the display screen, a Square Wave or Wave Image will
appear. If the CAL terminal says 1 Khz and 2 Vpp this means that the oscilloscope needs to
be calibrated so that the peak to peak value in the div box has a value of 2 volts with a wave
frequency equal to 1 KHz.
Set Volts/Div
Rotate the Channel 1 volt/div selector to 1 volt/div and make sure the square wave height is
exactly 2 div / vertical square on the oscilloscope screen. It is intended to meet the 2 Vpp
condition. If the vertical height of the square wave exceeds 2 div or even less, then please
turn the var knob to adjust the tension height. If the square wave that appears is right at 2 div,
then the method for calibrating the voltage in channel 1 has been successful.
The next step is frequency calibration by rotating the time/div knob to the 0.5 ms/div
position. In order for the square wave frequency to meet the standard of 1 Khz, the period of
1 wave must be 1 ms. So make sure the 1 period of the square wave that appears is exactly 2
div / horizontal box. If the period of the square wave exceeds 2 div or even less, then please
turn the var knob to adjust the length of the wave period. The period value in 1 wave can be
calculated with a value of 0.5 ms + 0.5 ms to 1 ms. Thus, the frequency value with the
symbol f is equal to 1/T, which is 1/1 ms or 1/0.001 s = 1000 Hz or 1 KHz.
The oscilloscope is ready to use
If channel 1 has finished calibrating the frequency and voltage, then the channel 1
oscilloscope is ready for use. However, to use channel 1 and channel 2, of course you also
have to calibrate channel 2 as well. The way to calibrate the oscilloscope on channel 2 is the
same as the calibration steps on channel 1 above by adjusting the settings from channel 1 to
channel 2.
Tutorial Kalibrasi Oscilloscope
1. Osiloskop
2. Kabel Power
3. Probe Positive dan Negative
Setelah semua peralatan disiapkan, kamu perlu mengikuti langkah berikut ini :
Persiapkan peralatan yang diperlukan dan lakukan pengecekan kabel probe maupun kabel
power, pastikan semuanya dalam kondisi yang baik. Pengecekan kabel dapat dilakukan
dengan menggunakan multimeter. Pengecekan ini bertujuan agar proses kalibrasi dapat
berjalan lancar.
Langkah selanjutnya yaitu dengan menghubungkan terminal 3 pin kabel power ke soket pada
bagian belakang osiloskop dan menghubungkan steker kabel power ke sumber listrik 1 fasa.
Nyalakan Oscilloscope
Nyalakan osiloskop dengan cara menekan tombol power yang terletak di kanan bawah layar
osiloskop, kemudian pastikan layar osiloskop bisa menyala dengan jelas yang ditandai
dengan adanya garis yang muncul dalam layar. Jika garis tersebut terlihat masih kabur, Kamu
bisa mengatur fokusnya terlebih dulu dengan memutar bagian knob fokus di bagian bawah
layar dan menyesuaikannya dengan tampilan garis pada layar agar dapat dilihat dengan jelas.
Selain itu, pastikan pula garis yang terlihat dalam kondisi lurus dan berada tepat di tengah
layar, jika garis tersebut sedikit miring, segera perbaiki dengan memutar tingkat kemiringan
garis dalam lubang bagian bawah layar memakai obeng. Dan untuk mengatur posisi garis ke
tengah, maka putar / atur knob position yang terletak diatas selektor volt/div channel 1.
Pasangkan konektor BNC probe pada soket BNC channel yang akan dikalibarasi. Untuk
memudahkan, maka pasangkan konektor BNC probe ke soket BNC channel 1terlebih dahulu.
Pada Langkah ini sambungkan ujung probe (+) yang berwarna merah dalam terminal CAL di
osiloskop yang terdapat dalam ujung kiri bagian bawah layar. Dalam tampilan layar akan
muncul Gelombang Kotak atau Wave Image. Jika dalam terminal CAL terdapat tulisan 1
Khz dan 2 Vpp ini artinya osiloskop perlu dikalibrasi supaya nilai peak to peak dalam kotak
div memiliki nilai 2 volt dengan frekuensi gelombang sama dengan 1 KHz.
Atur Volt/Div
Putar selektor volt/div Channel 1 dalam posisi 1 volt/div dan pastikan tinggi gelombang
kotak berada tepat di 2 div / kotak vertikal pada layar osiloskop. Hal ini dimaksudkan untuk
memenuhi kondisi 2 Vpp. Bila tinggi vertikal gelombang kotak melebihi 2 div atau bahkan
kurang, maka silahkan putar tombol var untuk menyesuaikan tinggi tegangnnya. Jika
gelombang kotak yang tertampil sudah tepat berada pada 2 div, maka cara mengkalibrasi
tegangan dalam channel 1 sudah berhasil.
Langkah selanjutnya adalah kalibrasi frekuensi dengan memutar knob time/div ke posisi 0,5
ms/div. Agar frekuensi gelombang kotak dapat memenuhi standar sebesar 1 Khz maka
periode 1 gelombang tersebut haruslah 1 ms. Sehingga pastikan 1 periode gelombang kotak
yang tertampil berada tepat 2 div / kotak horizontal. Bila periode gelombang kotak melebihi 2
div atau bahkan kurang, maka silahkan putar tombol var untuk menyesuaikan panjang
periode gelombangnya. Nilai periode dalam 1 gelombang bisa dihitung dengan nilai 0,5 ms +
0,5 ms menjadi 1 ms. Dengan demikian, nilai frekuensi yang bersimbol f ini sama dengan
1/T, yaitu 1/1 ms atau 1/0,001 s = 1000 Hz atau 1 KHz.
Jika channel 1 sudah selesai dikalibrasi frekuensi dan tegangannya, maka channel 1 osiloskop
pun sudah siap digunakan. Akan tetapi, untuk menggunakan channel 1 dan channel 2, tentu
saja Kamu juga harus mengkalibrasi channel 2 juga. Cara kalibrasi osiloskop pada channel 2
dilakukan sama seperti langkah-langkah kalibrasi pada channel 1 diatas dengan
menyesuaikan pengaturan yang awalnya pada channel 1 menjadi channel 2.