Professional Documents
Culture Documents
Datasheet
Datasheet
TRIPLEX 5 - 15 SPC
4107 9513 96.01
BASE MOUNT
Page 1 of 5
19 March 2020
SPECIFICATION
Single Point Connection (SPC) System Design Air Receiver
The Oil-Less Scroll Laboratory air package features a common Corrosion resistant, ASME Coded, National Board Certified
base with single point connections for electrical, discharge vertical air receiver rated for minimum 200 psig (1379 kPa)
air, and condensate drains. Designed and manufactured with design pressure.
ISO 13485 processes, each system is completely tested before
The air receiver assembly includes:
shipment and includes:
• Zero Loss electronic drain valve, liquid level gauge glass, safety
• Three “oil-less” scroll compressors and three motors, or three
relief valve, and manual drain valve
compressor towers, each with two “oil-less” scroll compressors
• Piped 3-valve bypass assembly with flange-fitted valves
and one motor
• Pressure gauge
• Duplex desiccant drying system with purge control
• Integral pre-wired control panel
Dryer/Filter/Regulator System
• Corrosion resistant vertical air receiver
Each desiccant dryer is sized for peak calculated demand
Compressor Module and produces a -40°F (-40°C) pressure dew point. Each dryer
operates from a demand based purge saving control system
The compressors are continuous duty rated scroll type, single featuring repressurization cycles. The dryer assembly includes
stage and air-cooled. The compressors have one fixed and one the following mounted and piped:
orbiting scroll sealed with PTFE tip seals.
• Fully duplexed high efficiency coalescing prefilters, each with
• Field replaceable tip seals automatic drain and element change indicator. Prefilters rated
• Dust and contamination protection from two part face seal for 0.01 micron.
• Orbiting bearing and pin crank bearings are grease filled • Adjustable multi-orifice purge valve assembly
• Heat dissipation maximized by an integral cooling fan • Fully duplexed rough and fine particle final line filters in series,
• V-belt driven compressor protected by totally enclosed belt each with manual drain and element change indicator. Final
guard line filters rated for 0.01 micron.
• Fully adjustable motor mounting base to achieve belt • Duplexed final line regulators and safety relief valves
tensioning • Ceramic type dew point sensor with ± 2°F system accuracy
BeaconMedæs • 1059 Paragon Way, Rock Hill, SC 29730 • Phone: (803) 817-5600 • Fax: (803) 817-5750 • www.beaconmedaes.com
SSB-138-03
4107 9513 96.01
Page 2 of 5
19 March 2020
8 7 6 5 4 3 2 1
Standard Configuration
NOTES:
D
Model Shown: 7.5 Hp Triplex D
A A
8 7 6 5 4 3 2 1
NOTES:
High efficiency inlet and outlet filters
to protect the desiccant beds and air
7.5 HP TX / 200 GALLON SHOWN
6
stream, achieving ISO 8573-1:2010
D D
Class 1.2.0.
moisture efficiently.
4
Anodized aluminum blocks and 7
9 flanged fittings utilized throughout air
stream design to reduce leak points.
Notes: 1. Normal operating conditions at a maximum ambient of 105°F. Consult factory for higher ambient conditions.
2. All capacities are shown as system capacities (all compressor modules running) and are shown in Standard Cubic Feet
per Minute (SCFM). Unit performance measured according to ISO 1217, Ed. 3, Annex C-1996. Reference conditions:
absolute inlet pressure 14.5 psig (99.97 kPa) , intake air temperature 68°F. System capacity does not account for losses due
to dryer purge or other system losses.
3. All system BTU/HR are shown with all compressor modules running.
4. All noise levels are shown in dB(A) and all compressor modules running.
5. System is designed for output pressure of 110 psig (758 kPa). For alternate pressures contact factory.
Standard Configuration
8 7 6 5 4 3 2 1
5 Hp - 7.5 Hp Triplex
NOTES:
(7.5 Hp Shown)
7.5 HP TX / 200 GALLON SHOWN
D D
"L"
1/2" FNPT
COND. DRAIN “L”
C C
"W2"
"W1"
B B
"H"
1-1/4" FNPT
DISCH. CONN.
A A
Notes: 8
• Discharge flex connections are built into package.
7 6 5 4 3 2 1
• Allow 36" in front of control panel for maintenance and ventilation, all other sides require 24" of clearance.
• Additional drawings/diagrams available for download at www.beaconmedaes.com.
SSB-138-03
4107 9513 96.01
Page 5 of 5
19 March 2020
Notes: 1. Normal operating conditions at a maximum ambient of 105°F. Consult factory for higher ambient conditions.
2. All capacities are shown as system capacities (all compressor modules running) and are shown in Standard Cubic Feet per
Minute (SCFM). Unit performance measured according to ISO 1217, Ed. 3, Annex C-1996. Reference conditions: absolute
inlet pressure 14.5 psig (99.97 kPa), intake air temperature 68°F. System capacity does not account for losses due to dryer
purge or other system losses.
3. All system BTU/HR are shown with all compressor modules running.
4. All noise levels are shown in dB(A) and all compressor modules running.
5. System is designed for output pressure of 110 psig (758 kPa). For alternate pressures contact factory.
Standard Configuration
8 7 6 5 4 3 2 1
10 Hp - 15 Hp Triplex
NOTES:
"L"
1/2" FNPT
COND. DRAIN
C C
"W2" "W2"
"W1"
B B
"H"
1-1/4" FNPT
DISCH. CONN.
A A
• Allow 36“ in front of control panel for maintenance and ventilation, all other sides require 24“ of clearance.
• Additional drawings/diagrams available for download at www.beaconmedaes.com.
BeaconMedæs
1059 Paragon Way
Rock Hill, SC 29730
Phone: (803) 817-5600
Fax: (803) 817-5750
www.beaconmedaes.com