Professional Documents
Culture Documents
Viton GLT-505
Viton GLT-505
Viton GLT-505
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
GLT-505
Introduction Product Description
Viton GLT-505* is a new generation, peroxide
Chemical Composition Terpolymer of perfluoro-
curable fluoroelastomer. It combines the excellent methyl vinyl ether, vinyl-
fluids resistance and low temperature flexibility found idene fluoride and tetra-
in Viton GLT with the improved flow of a lower fluoroethylene, plus cure
viscosity polymer. Viton GLT-505 is designed for site monomer and process
compression and transfer molding of sealing devices aid
such as O-rings and gaskets. Physical Form Slab
Stock Properties
Viscosity, ML 1+10, 121°C (250°F)
Units 70 67 72 107 43
Mooney Scorch, MS at 121°C (250°F)
Minimum, in lb 37 37 39 58 23
2-pt rise, min 26.7 24.2 >30 >30 27.2
5-pt rise, min >30 >30 — — >30
ODR at 177°C (350°F), Microdie, 3° Arc, 15 min
ML, in lb 21 15 16 30 13
Ts2, min 1.3 2.0 2.5 1.7 1.2
Tc 90, min 6.2 4.6 4.9 6.9 7.0
Mc 90, in lb 103 107 91 95 96
MH, in lb 112 117 100 103 105
ROSAND Capillary Rheometer at 100°C (212°F), 1.5 mm Die, L/D = 0/1
Piston Speeds Shear Rate Pressure, MPa
12.7 mm/min 113 s–1 6.2 6.8 7.0 7.2 4.8
50.8 mm/min 452 s–1 8.9 9.9 9.7 9.8 6.8
127 mm/min 1130 s–1 13.8 17.7 14.9 15.4 9.2
Vulcanizate Properties
Slabs Cured: 10 min/177°C (350°F)
Post Cured: 24 hr/232°C (450°F)
Stress/Strain at 177°C (350°F)—Original, No Post Cure
100% Modulus, MPa (psi) — — — — —
Tensile Strength, MPa (psi) 2.8 (410) 3.3 (485) 2.9 (415) 4.3 (625) 3.1 (450)
Elongation at Break, % 61 57 72 97 76
Stress/Strain at –20°C (–4°F)—Post Cured
100% Modulus, MPa (psi) 20.8 (3020) — 22.7 (3290) 20.6 (2985) 16.0 (2315)
Tensile Strength, MPa (psi) 27.7 (4020) 23.2 (3370) 24.0 (3475) 27.9 (4050) 24.0 (3480)
Elongation at Break, % 161 87 106 164 162
Stress/Strain at 23°C (73°F)—Original, Post Cured
100% Modulus, MPa (psi) 6.8 (980) 8.1 (1170) 5.8 (845) 6.4 (935) 5.8 (845)
Tensile Strength, MPa (psi) 15.6 (2260) 14.9 (2160) 12.4 (1795) 15.4 (2230) 14.6 (2110)
Elongation at Break, % 171 167 194 173 179
Hardness, A, pts 74 78 76 73 74
(continued)
2
Table 1 (continued)
The Performance of Viton® GLT-505 in Typical Compounds
A B C D E
Viton GLT-505 Viton A-401C Viton B-70 Viton GLT Viton GLT-305
3
Table 2
The Effects of Fillers in Viton® GLT-505
F G H I J K
N990 N990 N990 N990 Alba- Blanc
Filler Type Black Black Black Black glos Fixe
Amount, phr 45 30 15 5 30 30
Stock Properties
Viscosity, ML 1+10, 121°C (250°F)
Units 94 78 66 61 82 70
Mooney Scorch, MS at 121°C (250°F)
Minimum, in lb 50 42 35 32 45 38
2-pt rise, min 26.3 >30 >30 >30 26.6 25.6
5-pt rise, min >30 — — — >30 >30
ODR at 177°C (350°F), Microdie, 3° Arc, 15 min
ML, in lb 22 20 18 17 24 20
Ts2, min 1.1 1.2 1.3 1.5 1.3 1.3
Tc 90, min 5.9 5.6 5.3 6.3 5.6 5.3
Mc 90, in lb 116 106 93 78 101 93
MH, in lb 126 116 101 85 110 101
ROSAND Capillary Rheometer at 100°C (212°F), 1.5 mm Die, L/D = 0/1
Piston Speeds Shear Rate Pressure, MPa
12.7 mm/min 113 s–1 7.3 6.9 6.6 6.3 6.8 6.3
50.8 mm/min 452 s–1 9.9 8.8 8.5 8.1 8.8 7.9
127 mm/min 1130 s–1 14.2 12.2 12.2 11.5 11.5 11.1
Vulcanizate Properties
Slabs Cured: 10 min/177°C (350°F)
Post Cured: 24 hr/232°C (450°F)
Stress/Strain at 177°C (350°F)—Original, No Post Cure
100% Modulus, MPa (psi) — — — — — —
Tensile Strength, MPa (psi) 5.2 (760) 3.6 (520) 2.6 (375) 1.6 (230) 2.3 (340) 1.8 (260)
Elongation at Break, % 76 70 74 61 56 46
Stress/Strain at 23°C (73°F)—Original, Post Cured
100% Modulus, MPa (psi) 10.8 (1570) 6.8 (980) 2.7 (395) 1.4 (210) 4.3 (625) 3.3 (480)
Tensile Strength, MPa (psi) 17.5 (2540) 17.0 (2470) 14.5 (2105) 8.7 (1260) 10.5 (1525) 11.1 (1610)
Elongation at Break, % 148 183 231 255 159 221
Hardness, A, pts 78 71 58 51 66 61
Stress/Strain at 23°C (73°F)—After aging 70 hr/200°C (392°F)
100% Modulus, MPa (% change) 11.0 (1.9) 6.9 (1.5) 2.8 (3.7) 1.5 (7.1) 4.6 (7.0) 3.2 (–3.0)
Tensile Strength, MPa (% change) 18.3 (4.6) 17.9 (5.3) 13.0 (–10.3) 7.7 (–11.5) 12.3 (17.1) 9.2 (–17.1)
Elongation at Break, % (% change) 155 (4.7) 196 (7.1) 216 (–6.5) 240 (–5.9) 182 (14.5) 202 (–8.6)
Hardness, A, pts 78 71 61 54 66 61
Stress/Strain at 23°C (73°F)—After aging 168 hr/200°C (392°F)
100% Modulus, MPa (% change) 11.0 (1.9) 7.0 (2.9) 3.0 (11.1) 1.5 (7.1) 4.2 (–2.3) 3.3 (0.0)
Tensile Strength, MPa (% change) 18.5 (5.7) 17.6 (3.5) 13.9 (–4.1) 6.4 (–26.4) 11.6 (10.5) 10.2 (–8.1)
Elongation at Break, % (% change) 160 (8.1) 194 (6.0) 225 (–2.6) 220 (–13.7) 178 (11.9) 213 (–3.6)
Hardness, A, pts 79 71 62 55 66 61
(continued)
4
Table 2 (continued)
The Effects of FIllers in Viton® GLT-505
F G H I J K
N990 N990 N990 N990 Alba- Blanc
Filler Type Black Black Black Black glos Fixe
Amount, phr 45 30 15 5 30 30
5
Table 3
Effect of Coagents/Acid Acceptors in Viton® GLT-505
L M N O P Q
Viton GLT-505 100 100 100 100 100 100
Calcium Hydroxide 4 — — 4 4 —
Zinc Oxide — 3 — — — 3
Maglite Y — — 3 — — —
MT Black (N990) 30 30 30 30 30 30
DIAK #7 — — — 4 2 —
DIAK #8 1 1 1 — — 0.8
Luperco 101XL 4 4 4 4 2 2.5
Stock Properties
Viscosity, ML 1+10, 121°C (250°F)
Units 78 701 75 69 74 74
Mooney Scorch, MS at 121°C (250°F)
Minimum, in lb 42 37 41 36 40 39
2-pt rise, min >30 >30 26.1 11.0 18.2 >30
5-pt rise, min — — >30 12.7 21.4 —
10-pt rise, min — — — 14.4 24.4 —
ODR at 177°C (350°F), Microdie, 3° Arc, 15 min
ML, in lb 20 21 23 22 24 21
Ts2, min 1.2 1.4 1.3 0.8 0.9 1.4
Tc 90, min 5.6 5.8 5.4 4.1 5.0 6.4
Mc 90, in lb 106 96 95 121 101 86
MH, in lb 116 104 103 132 110 94
ROSAND Capillary Rheometer at 100°C (212°F), 1.5 mm Die, L/D = 0/1
Piston Speeds Shear Rate Pressure, MPa
12.7 mm/min 113 s–1 6.9 6.9 7.0 7.0 7.2 7.3
50.8 mm/min 452 s–1 8.8 8.9 9.1 9.1 9.5 9.9
127 mm/min 1130 s–1 12.2 12.2 12.7 12.4 14.4 14.6
Vulcanizate Properties
Slabs Cured: 10 min/177°C (350°F)
Post Cured: 24 hr/232°C (450°F)
Stress/Strain at 177°C (350°F)—Original, No Post Cure
100% Modulus, MPa (psi) — — — — — —
Tensile Strength, MPa (psi) 3.6 (520) 3.1 (455) 3.4 (500) 4.2 (615) 3.5 (510) 3.1 (450)
Elongation at Break, % 70 81 79 58 68 87
Stress/Strain at 23°C (73°F)—Original, Post Cured
100% Modulus, MPa (psi) 6.8 (980) 4.9 (710) 6.0 (865) 11.8 (1710) 8.2 (1185) 3.7 (540)
Tensile Strength, MPa (psi) 17.0 (2470) 16.7 (2415) 18.4 (2665) 18.4 (2670) 18.2 (2635) 19.6 (2845)
Elongation at Break, % 183 205 189 136 168 265
Hardness, A, pts 71 70 70 76 71 68
Stress/Strain at 23°C (73°F)—After aging 70 hr/200°C (392°F)
100% Modulus, MPa (% change) 6.9 (1.5) 5.6 (14.3) 5.9 (–1.7) 11.8 (0.0) 7.8 (–4.7) 4.7 (27.0)
Tensile Strength, MPa (% change) 17.9 (5.3) 18.3 (9.6) 17.6 (–4.3) 18.1 (–1.6) 17.8 (–2.2) 18.1 (–7.7)
Elongation at Break, % (% change) 196 (7.1) 205 (0.0) 189 (0.0) 138 (1.5) 172 (2.4) 247 (–6.8)
Hardness, A, pts 71 70 69 76 72 69
Stress/Strain at 23°C (73°F)—After aging 168 hr/200°C (392°F)
100% Modulus, MPa (% change) 7.0 (2.9) 5.8 (18.4) 5.7 (–5.0) 11.4 (–3.4) 8.1 (–1.2) 4.4 (18.9)
Tensile Strength, MPa (% change) 17.6 (3.5 ) 18.2 (9.0) 17.2 (–6.5) 18.3 (–0.5) 17.6 (–3.3) 18.8 (–4.1)
Elongation at Break, % (% change) 194 (6.0) 195 (–4.9) 192 (1.6) 143 (5.1) 169 (0.6) 253 (–4.5)
Hardness, A, pts 71 71 69 76 72 69
(continued)
6
Table 3 (continued)
Effect of Coagents/Acid Acceptors in Viton® GLT-505
L M N O P Q
7
Table 4
The Performance of Viton® GLT-505 to MIL-R-83485 Specification
R S
Viton GLT-505 Viton GLT
Viton GLT-505 100 —
Viton GLT — 100
Calcium Hydroxide 4 4
MT Black (N990) 10 10
Austin Black 20 20
VPA #3 0.5 0.5
DIAK #7 — 4
DIAK #8 1 —
Luperco 101XL 4 4
Stock Properties
Viscosity, ML 1+10, 121°C (250°F)
Units 89 117
Mooney Scorch, MS at 121°C (250°F)
Minimum, in lb 49 62
2-pt rise, min 23.1 10.1
5-pt rise, min >30 11.6
10-pt rise, min — 13.2
ODR at 177°C (350°F), Microdie, 3° Arc, 12 min
ML, in lb 23 33
Ts2, min 1.4 1.1
Tc 90, min 5.8 5.0
Mc 90, in lb 112 109
MH, in lb 122 117
MDR 2000 at 177°C (350°F), 1° Arc, 6 min
ML, in lb 5 8
Ts2, min 0:42 0:30
T′50, min 1:34 0:53
T′90, min 3:26 2:39
MH, in lb 40 41
(continued)
8
Table 4 (continued)
The Performance of Viton® GLT-505 to MIL-R-83485 Specification
R S Mil-R-83485
Viton GLT-505 Viton GLT (Amendment 3)
Vulcanizate Properties
Slabs Cured: 10 min/177°C (350°F)
Post Cured: 24 hr/260°C (500°F)
Stress/Strain at 23°C (73°F)—Original, Post Cured
Tensile Strength, MPa (psi) 13.4 (1940) 13.3 (1935) 11.0 min. (1600 min.)
Elongation at Break, % 164 125 120 min.
Hardness, A, pts 73 76 75 ± 5
Specific Gravity 1.73 1.72
Stress/Strain at 23°C (73°F)—After aging 70 hr/275°C (527°F)
Tensile Strength, % change (max) –17.8 –18.1 –35
Elongation at Break, % change (max) –8.5 24.8 –10
Hardness, pts change –1 –3 ±5
Weight Loss, % –6 –6 –12
Stress/Strain at 23°C (73°F)—After aging 70 hr/23°C (73°F)/TT-S-735 Type III (ASTM Reference Fuel B)
Tensile Strength, % change (max) –15.7 –5.4 –30
Elongation at Break, % change (max) –6.7 –1.6 –20
Hardness, pts change –2 0 ±5
Volume Swell, % 3 2 +1 to +10
Stress/Strain at 23°C (73°F)—After aging 70 hr/175°C (347°F)/AMS 3021 (Stauffer 7700 Blend)
Tensile Strength, % change (max) –22.1 –10.6 –30
Elongation at Break, % change (max) –12.8 –3.2 –20
Hardness, pts change –5 –5 –15 to +0
Volume Swell, % 15 14 +1 to +20
Compression Set (Method B), % 8 10 15
Stress/Strain at 23°C (73°F)—After aging 70 hr/200°C (392°F)/ARM-200
Tensile Strength, % change (max) –24.2 –15.2 –35
Elongation at Break, % change (max) –9.1 –4.0 –20
Hardness, pts change –6 –7 –15 to +0
Volume Swell, % 16 15 +1 to +20
Compression Set (Method B), % 8 8 10
Compression Set, Method B, %, 25 x 3.5 mm (0.984 x 0.139 in) O-Rings
70 hr/23°C (73°F) 7 11 25
166 hr/175°C (347°F) 20 23 25
22 hr/200°C (392°F) 10 14 15
Cold Temperature Properties
Brittle Point, °C (°F) –38.1 (–36.5) –37.5 (–35.5)
TR 10, (maximum, °C [°F]) –29.9 (–21.8) –30.6 (–23.1) –28.9 (–20.0)
DSC (glass transition temperature)
Inflection, °C (°F) –27.7 (–17.9) –29.4 (–20.9)
9
Test Procedures
(Test temperature is 24°C [75°F] except where specified otherwise)
Property Measured Test Procedure
Stress/Strain Properties
100% Modulus ASTM D412-87, pulled at 8.5 mm/s
Tensile Strength (20 in/min)
Elongation at Break
10
Proprietary Materials
Sources of compounding ingredients used in developing the information in this bulletin are listed here.
This is not to imply that comparable ingredients from other sources might not be equally usable.
DIAK * No. 7 curing agent Organic Triazine (TAIC) DuPont Dow Elastomers L.L.C.
DIAK No. 8 curing agent Trimethyallyl Isocyanurate Wilmington, DE 19880-0010
(TMAIC)
11
For more information on Viton® (800) 853-5515 (U.S. & Canada)
or other elastomers: (302) 792-4000
www.dupont-dow.com
Global Headquarters European Regional Asia Pacific Regional
DuPont Dow Elastomers L.L.C. Headquarters Headquarters
300 Bellevue Parkway, Suite 300 DuPont Dow Elastomers S.A. DuPont Dow Elastomers Pte Ltd.
Wilmington, DE 19809 USA 2, chemin du Pavillon 1 Maritime Square #10-54
Tel. 302-792-4000 CH-1218 Le Grand-Saconnex World Trade Centre
Fax. 302-892-7390 Geneva, Switzerland Singapore 099253
Tel. +41-22-717-4000 Tel. +65-275-9383
Fax. +41-22-717-4001 Fax. +65-275-9395
The information set forth herein is furnished free of charge and is based on technical data that DuPont Dow Elastomers believes to be reliable. It is intended for use by persons having
technical skill, at their own discretion and risk. The handling precaution information contained herein is given with the understanding that those using it will satisfy themselves that
their particular conditions of use present no health or safety hazards. Because conditions of product use and disposal are outside our control, we make no warranties, express or implied,
and assume no liability in connection with any use of this information. As with any material, evaluation of any compound under end-use conditions prior to specification is essential.
Nothing herein is to be taken as a license to operate under or a recommendation to infringe on any patents.
CAUTION: Do not use in medical applications involving permanent implantation in the human body. For other medical applications, discuss with your DuPont Dow Elastomers
customer service representative, and read Medical Caution Statement, H69237.